Search Documents

By James Y. Oldshue

"Very seldom is it possible when contacting a gas with a slurry to measure the dissolved gas concentration in the slurry, and even where possible, equilibrium data with a suitable Henry.s law constant are seldom available.In general, by assuming a reasonable value for the dissolved gas concentration in the slurry and a corresponding equilibrium gas partial pressure P*, KGa values can be calculated for the pilot plant and then scaled up. Then, with the same P* value at various reaction conditions, a mixer can be designed which is quite satisfactory, having a reasonable design factor for full-scale performance."

Jan 1, 2003

By Sergey Gudkov, Yuri Yemelianov, Stanislav Balikov, Andrey Boldyrev, Andrey Bogorodsky

"The results of POX of refractory gold-bearing concentrates using halide-ion as a lixiviant for precious metals and activated carbon as an adsorbent are given. It was found that gold did not recover to the solution when halide was added during POX. Silver partially dissolved in the solution. When halide-based reagents and activated carbon were added during POX, gold dissolved and loaded onto the activated carbon. The degree of sulfides oxidation was 99.3-99.6%. The recovery of gold onto granulated carbon was 94.7-94.8% when using chlorine-bearing lixiviants: NaCL, CaCL and carnalite and 98-99% when using KJ and KBr. This treatment process of refractory gold-bearing concentrates combines sulfide oxidation, dissolution and adsorption of precious metals. The results of the metals recovery achieved using this process can be compared with the recovery during POX-cyanidation. In this case, sodium cyanide was not used. This allows the reduction of capital and operational costs due to the absence of cyanidation, CIL and detoxification of leaching tailings circuits."

Jan 1, 2014

By J. Gebhardt, D. McBride, M. Cross, S. Gilbert

Heap leaching of ores containing chalcopyrite offers a low cost option to treat low grade complex copper sulfide ore bodies. However, the slow leach kinetics of chalcopyrite at ambient conditions typically results in unacceptably low recoveries. As the mineralogy of new ore deposits becomes more complex and the effects of gangue chemistry exert a greater influence on copper sulfide leach behavior, the control of leach reaction chemistry becomes more critical. Computational fluid dynamics (CFD) technology has been useful in the capture of multi-phase interactions and provides a path to simulate complex fluid flow, gas and liquid phases, through the heap, along with species transport. Coupling the flow models with the reactive mineral dissolution, and the sometimes competing aqueous chemical and solid-liquid reactions, yields a comprehensive model of the heap leach process. The leach kinetics of chalcopyrite dissolution in heap conditions is examined, and the incorporation of chalcopyrite leach kinetics in the CFD model is described. The application of the model to investigate optimization of the heap is discussed.

Jan 1, 2014

By Tsuyoshi Hirajima, Hideyuki Okamoto, Himawan .. T. B. M. Petrus, Keiko Sasaki

"Flotation of arseno bearing minerals from their copper ore has been an interest due to the increasing awareness on protecting the environment by minimizing the possibility of exposed arsenic compound. Some approaches have been proposed, but the mechanisms of separations have not yet fully understood. In this study, oxidation using oxygen was applied. Instead of the complex copper ore flotation results, pure single mineral of tennantite and chalcopyrite foatability was conducted using Hallimond tube. Resembled with the flotation results of copper concentrate containing tennantite, the separation possessed the best result at alkaline condition (pH 11) at where the arsenic content was reduced from 3300 ppm to 1800 ppm. In order to be able to understand the mechanism of the separation atomic force microscope (AFM) was utilized. AFM images showed changes in morphology and behavior when minerals were treated in both acid and alkaline condition. It was found that the morphological change showed the reaction products representing the rate of reactivity of tennantite and chalcopyrite. From the measured force of adhesion, it can be observed that in alkaline condition the surface of both minerals is more hydrophilic than that in acidic condition possessing higher value. This is in accordance with the X-ray photoelectron spectroscopy (XPS) spectra in which hydroxide moieties occupied the mineral surface in alkaline condition while elemental sulfur is in acidic condition."

Jan 1, 2014

By Kr. J. Dedelyanova

Selective flocculation of iron minerals could improve the economics of high intensity magnetic separation as concomitant process. When the minerals are finely disseminated is necessary a finer grinding to be applied which generates a lot of slimes. The HIMS is not enough efficient for particles below 20 microns ? territory where the selective flocculation is already well known industrial practice, so the combination of these two methods of beneficiation can bring a higher grade at high recovery to be achieved. The dynamics and selectivity of the precipitation process is studied in batch tests with flocculant starch and dispersants sodium silicate and sodium hexametaphosphate. The influence of preliminary conditioning with nitrogen acid at pH 2 before flocculation is also investigated. Flowsheet including these two methods is tested and the distribution of iron is shown.

Jan 1, 2014

By Andrei Kolesnikov

"The results of CFD modelling of complex heat transfer and fluid flow in DC electric arc furnace are presented. The model includes energy and momentum conservation equations for gas phase (freeboard), liquid phase (molten bath) and solid phase (walls and graphite electrode). Simulation revealed the temperature distribution in all elements of the furnace. The influence of the arc and melt resistance on the temperature distribution is discussed.Computational Fluid Dynamics (CFD) becomes a powerful tool for better understanding of the heta and mass transfer processes in industrial equipment. In current work commercial CFD software STAR-CD was used to analyse complex heat transfer in DC EAF, including forced and natural convection, conduction and radiation. The finite volume solver using body-fitted grid was used. The grids are non-staggered hexahedral grids and all variables are evaluated at cell centers. Steady-state calculations were performed with PISO algorithm. For the convective terms in equations the hybrid differencing scheme was used. An upwind differencing scheme was used for other terms. Conjugative heat transfer was taken into account in heat transfer calculations on gas-liquid and gas-solid interfaces. Radiation from the arc and inner surfaces of the furnace was calculated by a “discrete beam” approach. Source term in energy conservation equation was used to represent heat release in the zone occupied by the DC electric arc. The volume of this zone was calculated from semi-empirical equations. The Joule heat and heat due to chemical reaction in the melt were calculated through the source term expression in the energy balance equations for the slag and metal in the molten bath. The gas acceleration in the electric arc zone and stirring of the slag due to gas bubbles motion were accounted for by momentum source terms in the momentum conservation equations.All simulations were carried out using axisymmetric two-dimensional grid. The grid resolution was 20 cm per cell in most part of the furnace, except the arc region, where resolution was 5 mm per cell."

Jan 1, 2003

By A. Sand

Within stamp-charged coke making a large volume of coal is compacted to one single coal cake before entering the coke oven chamber. This is done by means of several falling stampers in a stamping machine having a mold nearly of the oven?s dimensions. Producing a high quality coke also from inferior coals requires a cake density of approximately 80% of the coal density. Besides that the industrial stamp-charging process demands a minimum mechanical strength of the coal cake to move it from the stamping mold into the oven chamber without failure. Densification and the build-up of cake strength were investigated earlier in stamping tests using a micro-stamping device. The quantities derived from these tests (as e.g. cake density or porosity) represent average values for the entire cake. Statements describing the local compaction state at different heights are difficult to achieve without destructing the cake. In order to gain better insight into the densification process and the inner structure of the coal cake a computational model based on the discrete element method (DEM) has been set up using 2 and also 3-dimensional simulation software. The stamper?s position and velocity as well as the force acting on the stamper were monitored and the model?s response was compared against measurement data from laboratory stamping tests. It was possible to reproduce the force and displacement pattern of the stamper in response to the viscoelastic properties of the cake using standard DEM bonding and contact models. Furthermore, the rearrangement of particles in response to the compaction by the stamper was tracked by calculating their displacement at the point the stamper hit the coal surface. The latter can also be used as indicators of particle deformation or breakage. By defining control points at different heights the particle displacement, stress and strain rates, porosity could be studied at different heights. Keywords: coke making, coal stamping, compaction, agglomeration, DEM, simulation

Sep 1, 2012

By M. Mezzetti, E. Anders, O. Popov, P. Hoske, H. Lieberwirth, M. Voigt

"The material breakage induced by high energy electric discharges is known in general as electric impulse technology. This technology can be used for processing solid materials, such as rocks and ores. The electric impulse technology has been around for about 60 years, originally developed and intensively investigated by Russian researchers. However, the application fields have been limited to research and laboratory scale projects. Currently, there are new attempts to transfer this technology into practical industrial applications. Practical examples include drilling of deep geothermal wells with an electric impulse driven drill-head. Traditional comminution implies high energy consumption, hence, high costs. The Electric Impulse Technology is interesting for comminution of mineral and complex ores since it could allow improved recovery and energy reduction, thus resulting in significant savings. Another advantage is the dust free processing, which contributes to make minerals processing environmentally friendly. The use of electrical comminution for processing complex ores is investigated within the ELIZE research project funded by the BMBF (project No. 033R161 A) and industrial partners. The main objective is the development of an industrial scale electrical comminution machine. The first development stages include the investigation and characterization of the electric impulse induced weakening on rocks and ores. The characterization results of the preliminary trials at the microstructural scale on granite, skarn and greisen will be presented and discussed in this article. INTRODUCTION The pioneer work in the area of electric impulse technology was conducted by Russian researchers about 60 years ago [1]. While there have been some successful attempts to transfer this technology into practical applications, such as rock processing [2], laboratory processing of mineral ores [3–5], recycling [5] and geothermal drilling [6–9], the jump into practical industrial large scale application has not been accomplished yet. The Institute of Mineral Processing Machines of the TU Bergakademie Freiberg currently leads a project which can be seen as the next logical step for the technology transfer to industrial applications, namely, the development of continuously operating complex ore processing machines based on the electric impulse technology."

Jan 1, 2018

By Jan Svoboda, Toyohisa Fujita

"The current status and history of innovation in magnetic methods of material treatment are reviewed. The milestones and key drivers of innovation are identified, advantages of magnetic separation in comparison to other physical methods of material manipulation are discussed and reasons for failure to live up to its potential and expectations are identified. The future focus in such diverse areas as mineral processing, waste treatment, recycling and biosciences is discussed and the research and development needs are outlined.Our walk through the innovation landscape in magnetic separation illustrates the enormous effort that has been expended over the years to convert a wealth of novel idea into workable techniques. Remarkable progress has been achieved and numerous successful innovations have been introduced into material treatment operations. On the other hand these techniques have experienced their fair share of failures. The reasons for these cover a wide spectrum of risks that accompany any effort to implement new technology."

Jan 1, 2003

By Häkkinen Antti, Salmimies Riina, Matveinen Maria

"Tailings generated during the upgrading of ore present a major challenge for the mineral processing industry. On one hand, the processing of tailings requires added capital input. On the other hand, increased difficulties in obtaining permits for dams and landfilling and increased costs associated with storage and tailings management also result in increased costs. To promote sustainability and make tailings management economical, added value must be generated from the waste material. This might be possible through the recovery of the metal values in the waste. This work discusses the possibilities of recovering metals from multimetal tailings through leaching in a stirred tank. The characteristics of the tailings are crucial and the distribution of the metals within the different size fractions is used to identify the most attractive route for the hydrometallurgical step. Leaching of nickel and copper is further investigated using acids at different concentrations. The leaching of base metals is possible at acidic conditions. Increased temperature and concentration of the leaching agent promote the dissolution of the metals, as could be expected. With simultaneous dissolution of several metals the dissolution mechanisms are difficult to identify. Furthermore, as several metals, not all of them being target elements, are leached another challenge arises from the selective recovery of those metals from the liquid phase."

Jan 1, 2014

By Carlos de F. Gontijo

The flotation of quartz particles was studied over the particle size range from 0.5 µm to 1000 µm and for advancing water contact angles between 0º and 83º. Flotation was performed in a column and in a Rushton turbine cell. Particle contact angle threshold values, below which the particles could not be floated, were identified for the particle size range 0.5~1000 µm, under different hydrodynamic conditions. The flotation response of the particles, either in a column or in a mechanically agitated cell with a similar bubble size, was comparable. Turbulence plays a role, as does bubble-particle aggregate velocity and bubble size. The stability of the bubble-particle aggregate controls the maximum floatable particle size of coarse particles. For fine particles, the flotation limit is dictated by the energy required to rupture the intervening liquid film between the particle and bubble. Flotation of very fine and large particles is facilitated with small bubbles and high contact angles. These results greatly extend our earlier observations and theoretical predictions.

Jan 1, 2014

By A. D. Shuloyakov, G. A. Finkelstein, V. I. Kurets, A. K. Vedin

"In disintegrating solid ores with mineral values disseminated in them, one of the principal tasks is to selectively separate valuable mineral particles from the matrix in which they reside, striving at the same time to keep their natural shape and size as intact as possible.The conventional mechanical disintegration methods do not meet this most important requirement in full. The other major objective here is to reduce electric power consumption during the fragmentation stage, since up to 65 per cent of the total power consumption at concentrators processing ores of non-ferrous, ferrous, rare, and precious metals is spent on disintegration steps.Numerous experiments conducted on dozens of ore types (tin, tungsten, and many others, as well as on rock containing diamonds, rubies, emeralds, etc.) have invariably demonstrated by far superior integrity of mineral values as compared with that obtained by mechanical as well as other types of disintegration.However, the process remains as power-intensive as ever which is due to the imperfect nature of the electro-technical devices that convert the network electric current into high-voltage electric impulses responsible for the disintegration process.The maximum capacity attained in disintegrating the hardest materials from 40 mm to 2 mm size in a single operating chamber with four high-voltage electrodes does not exceed 1.0-1.5 t/h. Attempts at increasing the number of electrodes and the capacity of the operating chamber have failed so far because of high overall dimensions and mass of the electrical part of the installation supplying the chamber with pulsating current, as well as of the commutation requirements. At the same time, a number of overseas operations have reported a significant breakthrough in their attempts to reduce dozens of times the overall dimensions and mass of the discharge impulse generating installation (EIS), which enables us to contemplate to increase the capacity of the EIS at least ten times in the nearest future. Yet, even with the currently achieved capacity of the EIS, these installations have found wide use in geological surveying, precious and semi-precious stones production, in grinding super hard materials, etc., since they provide spectacular selectivity of disintegration and thus the integrity of valuable mineral crystals."

Jan 1, 2003

By Pawel Strzalkowski, Marta Baszczynska, Urszula Kazmierczak

The paper presents issues related to interference of mining activities with the environment. Exploitation of mineral resources causes primarily a modification of the landscape. All of the negative impacts on environment are short-lived and last as much as it takes to exploit the raw material. After the mine closure reclamation is necessary during which all aspects that reduce harmful effects of the mining activities on the environment must be taken into account. Current ways of reclamation allow recreating natural environment, which is different from the original and enriched in diverse new values. This requires propositions of new forms of converted land development through a detailed analysis of technical, natural, planning, economic and social sphere requirements. Before making final decisions regarding selection of direction of reclamation, a thorough analysis of the key factors has to be carried out. All steps related to the implementation of the reclamation project are shown in the paper using Limestone Mine "Górazdze" located in the south-western part of Poland as an example. This paper also presents an analysis of current ways of post-mining reclamation towards agricultural and forestry landscape, along with our own suggestion for their extension in order to preserve biodiversity. For choosing optimal solutions the most relevant criteria were considered: existing natural values and possibility of their protection. Taking into account the economic and social aspects, supported by natural potentials, implementation of tourism and recreation in this area were proposed. It was shown that this proposition would not interfere with the current trends of the natural landscaping. Finally, after completion of reclamation and land development in the considered mine area, creation of a geo-park was proposed along with appearance of geotourism in the area. To illustrate the proposed forms of post-mining land development in the form of maps, an ArcGIS(ESRI) software was used.

Jan 1, 2014

By Alex Heath, Andrew Barycki, Baladron. Javier

"Efficient flocculation is important to thickener performance, affecting the overflow clarity, solids settling flux, underflow density and operability. Many factors affect flocculation; from the material/flocculant type, dilution of the feed and flocculant solution, mixing, to the shear rate and shear history. The flocculant addition point (or points) can be used as a tuning method to alter the effective flocculation time in a feedwell, with addition further up the feed pipe increasing the residence time but making the aggregates more prone to breakup if they experience high shear later in the process. Conversely, adding the flocculant later, eg under the feedwell shelf decreases the mixing time but allows some free (unadsorbed) flocculant to be available at the feedwell exit. An extensive trial has been performed on an operating thickener comparing seven individual different flocculant dosing positions through a Vane feedwell, and some combinations of two dosing points simultaneously. Measurements of the velocity, solids concentration and aggregate size were made throughout the feedwell at the different positions, with the dosing points significantly changing the aggregate size and clarity, and also affecting the solids concentration at some positions. The results are accessed in terms of flocculation kinetics and used as CFD validation data."

Jan 1, 2014

By N. Panteleeva, E. Konoplev, I. Michailova, S. Titkov, T. Gurkova, T. Chumakova, Sylvinit Co.

"INTRODUCTIONFlotation of mineral particles by cationic surfactants – namely alkyl amines and their derivatives – is finding ever growing application in processing of various ores and in quality refinement of the benefication end products, iron concentrates for example. In the recent years application of cationic collectors - alkylmorpholines - enabled the development of new highly efficient procedure of water-soluble mineral processing, being also the one with low energy consumption. This procedure is a reverse flotation of carnallite from bay salts of salt-pans and from carnallite ores.The efficiency of cationic SAS influence depends upon colloid-chemical state of the collector in flotation liquid phase, especially if the latter comprises mineral salts. Availability of clayey impurities or slime particles of iron oxide in cation flotation feed, which actively sorb the cationic collector, deteriorate considerably the cation flotation performances. In Halurgy Institute the investigations of cation flotation under potash and carnallite ore processing have been carried out, and new reagent modes, enhancing cationic surfactants sorption at mineral particles, have been developed. Application of new reagents enables one to decrease considerably the consumption of expensive cationic collectors and to enhance the floatability of coarse mineral particles."

Jan 1, 2003

By P. Knüpfer, B. Babel, M. Rudolph, F. Perez Maldonado, U. A. Peuker, L. Ditscherlein

"In heterocoagulation processes for the separation of mineral particles, the most famous being froth flotation, the main characteristic of separation is a differing wettability of the constituents to be separated. This most crucial property in the economically important process of flotation is often only and incompletely, quantitatively described in terms of contact angles against water. A water contact angle larger than 90° is referred to as hydrophobic and hydrophilic vice versa. Looking at Young’s equation shows that it is actually the surface energy of the solid in interaction with the surrounding phases and their surface energies (or surface tensions for liquids) which describes whether there will be hydrophobic/hydrophilic hydration interactions leading to attraction or repulsion. This, we have previously published for various more or less hydrophobic minerals in correlation to their flotation response, i.e. flotability (c.f. Rudolph & Hartmann, Coll.Surf.A 513, 380-388). In the same paper we also discussed the heterogeneity of wettabilities as assessed with the novel method of inverse gas chromatography. Furthermore we have also reported on hydrophobic force distributions as assessed with atomic force microscopy which are as well due to wettability heterogeneities (c.f. Fritzsche et al., Coll.Surf.A 459, 166-171).In this paper we present wettability distributions of different substrates and particles with various surface roughnesses/shapes and degrees of hydrophobization as assessed with iGC, AFM and dynamic sessile drop analyses. We are putting the results in context in unifying models and present methodologies helpful to make use of the fundamental information and their impact on the actual industrial separation process in fundamental process models. Besides froth flotation we also emphasize the impact on selective hydrophobic flocculation process."

Jan 1, 2018

By Avishan Atrafi

Frothing behavior of surfactants originate from their preferential adsorption at the gas-solution interface. Different surfactants may demonstrate different adsorption behaviors depending on their molecular structure and surface activity. The quantity and rate of adsorption of surfactants at the gas- solution interface in flotation systems will certainly affect kinetics of reaction and fractionation of surfactant between bulk and foam phase and subsequently their frothing characteristics. In this paper, the frothing characteristics of sodium oleate which is the main constituent of fatty acids used in flotation systems is explained. The adsorption behavior of sodium oleate is then compared to a typical non-ionic frother (Methyl Isobutyl Carbinol, MIBC) in terms of different adsorption behavior at the gas-solution interface. Since long chain fatty acids are weak electrolytes, their behavior is a strong function of pH. Also semi soluble salts including apatite contain considerable amounts of ions like calcium in their lattice, so the effect of presence of ions on the frothing behavior of fatty acids requires an investigation. A mass balance on the surfactant transferred to the foam was solved to estimate the bubble surface area flux in foam, which explained how the adsorbed surfactant at gas-solution interface controls the bubble surface area flux at foam. Since sodium oleate adsorption at foam takes place gradually, frother concentration as a function of time was monitored by the total organic carbon measurement (TOC) to compare the surfactant uptake rate at different concentrations, pH and ionic strength. The surfactant concentration adsorbed within foam together with the value of adsorption density from the Gibbs adsorption, leads to the calculation of the surface area flux and prediction of average bubble size in the foam at a specific time frame. This value was compared at different concentrations of sodium oleate. Dynamic surface tension measurements were accompanied to explain the adsorption behavior, though finally equilibrium surface tension turns out to better explain the foamability characteristics. Keywords: flotation collectors, flotation froths, foams, fatty acids, adsorption behavior

Sep 1, 2012

By Matt Kilburn, Liming Lu, Steve Suthers, Alexander Edenton, Rodney Smyth, Matt Adam

"Magnetite concentrate is naturally good for pelletising. However, due to the depletion of reserves of traditional high grade hematite iron ore worldwide, the usage of magnetite concentrate in sintering is expected to increase substantially. Magnetite concentrate is typically high in Fe grade and releases extra heat when oxidised to hematite. This will not only improve the quality of agglomerates produced, but also have a potential beneficial impact on the fuel consumption of the agglomeration process. There are an increasing number of magnetite projects currently being considered and developed. However the concentrates from some of these projects are too coarse as pellet feeds and much finer and denser than normal sinter feeds. Accordingly, special strategies are required in order to utilise the coarse magnetite concentrates at high proportions in pelletising and sintering. This paper discusses various raw material preparation technologies and blending optimization methods demonstrated to be effective for improving the sintering and pelletising performance of coarse magnetite concentrates. Pre-granulation and addition of binders, such as hydrated lime, were found to be particularly efficient in recovering the sintering productivity of sinter blends containing magnetite concentrates. In pelletising, HPGR (High Pressure Grinding Rolls) grinding enabled production of good quality pellets from 100% magnetite concentrates and optimized blends containing up to 70% magnetite concentrates also formed good pellets.INTRODUCTION Magnetite concentrates are often used as feed materials for pellet plants or sinter plants depending on their grades and grain sizes. To achieve the required quality of green and fired pellets, the concentrates often need to be ground very fine (80% passing 38- 45 m), which inevitably consumes a great amount of energy. Therefore, efficient grinding processes are required to reduce the amount of energy consumption needed to achieve the sizing and chemical specification of pellet feeds. The use of magnetite concentrates in sintering has the potential to improve sinter chemistry, which is deteriorating over time due to the slowly decreasing grade of direct shipping iron ores around the world (Yang and Mathews, 1997; Yang and Witchard, 1998, Yang and Davis, 1999; Yang 2005). However, methods are required to allow the utilisation of high levels of concentrates in sintering while maintaining productivity and sinter quality (Han and Lu, 2017)."

Jan 1, 2018

By Dietmar Freyhammer

Grinding is the last stage of the comminution process. In the grinding process the particles size are reduced by impact and attrition stresses. The fine grinding of ores is nowadays finding increased application due to depletion of coarse grained, easily processed ore bodies and the increased need to process distributed fine grained deposits, such fine ground iron ore powder is the basis for the pelletisation process. Depending on the ore type and the project environment different approaches to comminution are requested to provide an adequate ground iron ore for the pelletisation process. Currently the ball mill is the most used equipment in grinding iron ore for pellet feed. Based on the various examination and investigation of minerals on grind ability related to the throughput, to the resulting sieve characteristics and necessary energy consumption, the mill circuit can be: Open dry circuit. Closed dry circuit Open wet circuit Closed wet circuit. CEMTEC GmbH is a renowned name worldwide and offers tailor made solutions to cope these issues.

Sep 1, 2012

By Jaime Sepúlveda

"A broad diversity of critical operating conditions may influence, in very convoluted ways, the actual performance of any given mineral processing system, to the extent that it becomes nearly impossible to empirically determine the independent, decoupled impact of each condition. An effective approach to better understand the behaviour of such complex systems is via the extensive use of sufficiently detailed and reliable mathematical models, allowing the process analyst to explore and learn about the independent effect of all relevant operational conditions. Certainly, these tasks are greatly facilitated if the appropriate software tools - such as the Moly-Cop Tools software package - are readily available. Moly-Cop Tools 3.0 is a set of 63 easy-to-use EXCEL spreadsheets designed to help process engineers characterize and evaluate the operating efficiency of any given grinding circuit, following standardized methodologies and widely accepted evaluation criteria. Moly-Cop Tools 3.0 covers conventional and semiautogenous mills, crushers, HPGR’s, rod mills and vertimills, with the corresponding mass balance and parameter estimation routines; plus complementary spreadsheets regarding Bond’s Law calculations, grinding media selection and performance evaluations and other useful utility functions. As a relevant example of application, specifically focusing on semiautogenous grinding operations, the current publication describes how the models can help us learn and rationalise critical empirical observations such as the relationship between feed particle size and optimal ball filling, the role of the rocks as autogenous grinding media as well as the impact of feed size and discharge grate opening on the mill grinding capacity. Over the last 20 years, Moly-Cop Tools has gained wide acceptance around the mineral processing community in recognition to the quality of the mathematical models contained, their simplicity of application and ease of sharing of the calculations amongst all interested parties, since it is available free-of-charge with no restrictions to make as many copies as needed."

Jan 1, 2014