Search Documents

By T. Bednarski, T. McCallum, L. Moya, L. Nsenga, B. Mbao

The accumulation of solids in solvent extraction (SX) circuits can cause problems with the physical and economic performance of the operation. These solids are responsible for the formation of crud, a solid stabilized emulsion containing organic, aqueous, air, and fine solid particles. The build-up of crud in SX settlers can limit SX operation throughput, require plant downtime, lead to higher organic losses, or result in higher aqueous in organic entrainment (all of which can have a significant, negative economic impact). Current practices for crud management are typically reactive. Crud is physically removed after it has been allowed to build to excessive levels in the circuit and processed mechanically using centrifuges or filtration. A new proactive solution has been developed to prevent crud formation and build-up. Low ppm dosage of an additive, ACORGA® CR60, into the pregnant leach solution (PLS) has resulted in reduced crud formation in pilot and commercial scale for a variety of PLS streams. This paper will review results from operations in North America and Africa, covering heap leach, concentrate leach, and agitated leach feeds. INTRODUCTION Crud formation and build-up in solvent extraction (SX) circuits has been a long time topic discussed and claimed to be crucial to the whole hydrometallurgical process (Liu, et al, 2006). Crud formation is present in all SX systems be it copper, uranium, zinc, etc., and Ritcey (1980) defined crud as a stabilized emulsion containing organic, aqueous, and fine solid particles. The ore type and feed composition is a major determining factor of crud formation and typically contains Si, Al, Fe, P, and sulfates (Ritcey, 1980). It typically builds at the interface between the organic and aqueous, but can also be observed as floating crud on the surface of the settler, or bottom crud, which is common to find in circuits treating agitated leach feeds such as in Africa. As crud formation has been unavoidable, many of the current crud management techniques are reactive, allowing crud to form and build in SX circuits. Once it does, it is removed and treated via different mechanical techniques, typically through some type of filtration or three-phase centrifuge, to remove the solids and recover the organic phase trapped within the emulsion (Ritcey, 1980). Automated pumping systems have also been designed and are frequently used in North American operations. The time and capital required to react to crud formation can be an overwhelming aspect to SX operation.

Jan 1, 2019

"Since the publication of a literature review on this topic (McIvor and Finch. 1986), the author has been involved in more than thirty rod milling efficiency tests at seven different milling operations. There have also been several interesting additional articles on rod milling found in the literature. This update describes the most important findings from investigations carried out since the previous review, as well as developments in the techniques used to evaluate the grinding efficiency of rod mills.Rod Mill Power DrawA series of power draw versus charge level measurements were taken on the rod mills at Leg Mines Selbaie and Kidd Creek Mines Limited (McIvor. 1989). These revealed a significant (about 10070) loss in power draw with the installation of new liners, a common observation among rod mill operators. This loss in power draw depends on the liner design, particularly the average thickness and lifting face profile of the new liner. The theoretical power usage of both mills was approximately 5070 lower than that given by the Allis-Chalmers power draw formula (Rowland. 1982).The shape of the power draw versus charge level curve suggested an opportunity for reducing media consumption. By increasing mill speed, power draw could be maintained with a smaller mill load, most significantly for mills operating with high charge levels. Analysis of data from 62 installations confirmed this (McIvor, 1989). On average, a 10 percentage point increase in critical speed results in a 15070 in specific media consumption (Le. kg of steel consumed per kWh of energy consumed). Table 1 lists a number of relatively high speed rod milling installations. No negative effects on the drive train, liner life, or the tendency for rods to tangle have been reported. A reduced lifting angle of the new liner leading face (e.g. 45 versus 90 degrees from the mill perimeter) is recommended for higher speed rod mills (Leclerq, 1990)."

Jan 1, 1995

By Afshin Sadri, Wai Lai Ying, Brycklin Wilson, Zoe Coull

"Although there have been great steps forward to integrate corrosion engineering into operations, there is still an underlying tendency for maintenance tasks to be performed in a reactive manner. This is especially true when strategies focus on lagging indicators such as visual inspections, RCA (root-cause analysis), and FMECA (failure mode, effects and criticality analysis). This trend to “reactive maintenance” can be avoided by utilizing more inspection and monitoring methods to identify leading indicators of failures. Prevention is generally less costly than repairs; moreover, when paired with appropriate monitoring techniques, intervention of corrosion protection can be more effectively timed and based on more accurate data. Hatch asset reliability studies show nearly 80% of defects are introduced through operations and maintenance. Therefore, proactive corrosion management can provide the necessary feedback to optimize operations and maintenance strategies preventing costly corrosion losses. Understanding corrosion risks gives a clear picture of the benefits of a proactive approach to asset performance. Monitoring techniques (Non-Destructive Testing, field testing, sampling, etc.) by nature are a more effective means of improving maintenance efforts and preventing corrosion losses than other methods (RCA, FMECA). This paper will outline the importance of proactive corrosion management and demonstrate its benefits through industry examples.INTRODUCTION Over the past few decades, with the growth of technology and awareness of sustainable development many studies have shown the benefits of a proactive approach to maintenance strategies. However, in practice there is still an underlying tendency for maintenance tasks to be performed in a “reactive manner”. This is especially true when strategies focus on lagging indicators such as visual inspections, RCA (root-cause analysis), and FMECA (failure mode, effects and criticality analysis). This trend to “reactive maintenance” can be avoided by utilizing more inspection and monitoring methods to identify defects and leading indicators to failures."

Jan 1, 2017

By D. J. Charlton

"IntroductionMaintenance is a business, which to be successful, requires good management, systems and reporting. The prime objective of the maintenance management group, be they large or small, must be to anticipate and prevent interruptions in operations by keeping equipment in good mechanical condition. This objective should be carried out at minimum cost consistent with maximum productiveness.The objective of this chapter is to give an insight into the various aspects of maintenance management that must be considered to effectively and efficiently operate a mill complex. The degree to which the maintenance sub-systems are developed in an operating mill will be determined by the size of the mill and the needs of the operation.The criterion of the management system used is that the system serve the operation and not vice versa. The systems presented should be considered as tools and, as with all tools, they must be sharpened and replaced as the need arises or as more effective tools become available.To understand what is involved in maintenance management, it is worthwhile to consider a systems approach to analyzing management problems. This approach was developed by J.A.B. Rae while reviewing maintenance management systems for Cominco Ltd.A very simple system involving managing results and objectives is shown diagrammatically in Figure 1.The systems approach to organizational development involves four basic elements: an objective, a result, an activity and feedback. In the analysis, the activity element is broken down into individual actions that people could be held responsible for. If we introduce the action of operating into the diagram of Figure l, we arrive diagrammatically in Figure 2."

Jan 1, 1989

By D. Murray

A 2-hectare uranium tailings area has been reclaimed. The exposed tailings of 1.4 hectares were capped with glacial till and vegetated with grasses and legumes. The water running through the tailings was diverted around the tailings in a line ditch and treated with sodium hydroxide and barium chloride. Difficulties occurred in placing the till capping because of the low bearing strength and the uneven surface of the tailings. This led to varying thicknesses of till and the need for manual labour in some areas. Total reclamation costs were $32,200, with vegetation establishment costs at $13,700 per hectare. This report provides a record of work for use in assessing the long-term suitability of these treatments.

Jan 1, 1979

By M. Kalin

Tailings deposits are frequently the source of ground water contamination due to the transport of contaminated tailings pore-water. If amendments to tailings covers could be made to facilitate a precipitation reaction and halt or reduce the generation of acid in pyritic tailings, the quality of pore-water quality would be improved which would in turn reduce the production of contaminants. The effects of phosphate wastes, added to base-metal mine tailings in Newfoundland, Canada, were tested. Laboratory and field experiments determined the effects of different mixing ratios of phosphate wastes to tailings volume (1:4, 1:8, 1:12 and 1:20, dry weight) for a total period of 3.2 years. The addition of phosphate at ratios of 1:4 to 1:12 substantially increased the pore water pH, and reduced both acidity and Zn concentrations. These results suggest that addition of phosphate wastes to tailings covers can reduce acidity generation and improve tailings pore-water quality.

Jan 1, 2004

By M. F. Gallerneault, V. Fallah, A. Howells, W. M. T. Gallerneault

"The occurrence of recrystallization in cold-worked aluminum sheet during the brazing process leads to loss of strength, an inhomogeneous grain structure and reduced corrosion resistance. AlMgScZr alloys are known for their extraordinary recrystallization resistance due to the influence of Sc and Zr addition on their microstructure. Here, we investigate the effect of alloy composition (i.e. Mn, Mg, Sc, Zr content), cold-roll reduction and pre-aging treatment on the recrystallization behavior of cold-rolled sheets at brazing temperatures typically used during the manufacture of heat exchanger units. The analysis of recrystallization behavior is carried out through microstructural characterization and the results are compared with the behavior of a commercial, AA3xxx-based heat exchanger alloy.INTRODUCTION Control of recrystallization is of critical importance during brazing, which is a widely-used joining technique for aluminum alloys in aircraft structures (Heinz, 2000) and automotive heat exchangers (Miller, 2000; Marshall, 1993). Due to excessive local heat at brazing temperatures, the cold work texture of aluminum alloys in the cold-rolled sheets may undergo a local recrystallization process (Marshall, 1993). This leads to the formation of an inhomogeneous microstructure and thus anisotropic mechanical properties (Miller, 2000) and low corrosion resistance (Marshall, 1993) across the sheet. X800, a commonly-used Al-Mn alloy series for automotive heat exchangers applications, has been developed specifically for a higher strength as well as an enhanced corrosion resistance as opposed to the traditionally-used AA3003 alloy (Marshall, 1993). X800 alloys, however, exhibit a low recrystallization resistance at normal brazing temperatures, i.e. 590°C. In contrast, Al-Sc-Zr alloys have been shown to exhibit an extraordinary recrystallization resistance at such temperatures (Riddle, 2004) while also being corrosion resistant and possessing a high room-temperature strength (Fuller, 2002). This has been shown to be due to the formation of coherent, nanoscale Al3(ScZr) precipitates that effectively impede grain boundaries while also exhibiting very slow coarsening kinetics at high temperatures (Riddle, 2004; Jones, 2003; Ocenasek, 2001). In this study, we analyze the recrystallization behavior of X800 alloys under brazing conditions through introducing Sc and Zr into the system as well as varying the Mn and Mg content. The effect of processing route is also studied by introducing a pre-aging stabilization treatment as well as varying the cold-roll reduction prior to the final brazing anneal."

Jan 1, 2018

By R. J. Twigg, S. D. Chang

"The production of heavy water, the moderator in a CANDU reactor, is examined following a flow sheet of a typical Canadian plant. The process involves the extraction and concentration of deuterium from natural water through a chemical exchange mechanism with hydrogen sulphide. Consequently, corrosion problems associated with sour environments – the use of hydrogen sulphide - are an everyday problem and have led to the development of a highly refined materials selection and testing program to prevent equipment from failing prematurely.IntroductionHeavy water is a naturally occurring compound in ordinary water and is formed from the combination of two deuterium atoms and one atom of oxygen. Deuterium is a heavy hydrogen atom which has a nucleus of on e proton and one neutron. Hence, heavy water is a combination of heavy hydrogen and oxygen and is chemically known as deuterium oxide. It looks and tastes like ordinary water but it freezes at 3.8°C and boils at 101.4°C. The molecular weight of heavy water is 20 as compared to 18 for ordinary water; the density of heavy water is ten per cent greater than that of ordinary water.Although heavy water and ordinary water exhibit only small differences in their chemical and physical properties, there are large differences in their nuclear properties, the most important of which is the neutron moderating ratio, used to measure the ratio o f the slowing down power to the neutron capture characteristics. For heavy water the ratio is 21000 and for ordinary water it is 50. This high moderating ratio is essential for achieving a high neutron economy. Heavy water is, therefore, chosen as the moderating and heat transport fluid in the CANDU reactor."

Jan 1, 1983

By Robert B. Wickham

"American Barrick has always balanced its aggressive operating approach with a conservative financial strategy. In fact, what enables their mining team to pursue such aggressive plans with confidence is the conservative financial strategy adhered to by the company. These policies are built on a prudent mix of gold linked financings, equity and gold price hedging.This paper outlines these policies and focusses in particular on American Barrick's gold price hedging program.IntroductionThe company's balance sheet at the end of 1990 clearly shows the wisdom of its conservative policies. Total assets have grown to over US$1 billion; cash has grown to US$312 million and shareholders' equity to US$645 million. All amounts included in this paper are quoted in U.S. dollars. Increased gold production and an effective gold price hedging program also combined to produce record income from operations, earnings and cash flow in 1990.The first half of 1991 is also indicative of the benefits of the company's conservative financial policies. Increasing production, together with its comprehensive gold hedging program, has generated increased earnings, even in a period of falling gold prices.All year-over-year numbers for the first six months are up. Gold production was 36% higher; earnings of $40.2 million $ 0.30 per share - were 46% higher than 1990.Barricks revenue continued to increase despite gold prices remaining unchanged during 1990. Barrick's hedging policy protects the company from falling gold prices on the basis that the upside looks after itself. Their hedging program - including various goldlinked fmancings - enabled Barrick to realize an average price of $437 per ounce of gold sold in 1990, compared with the Comex average gold price for the year of $384 per ounce."

Jan 1, 1991

By Alex MacEachern

Air is the gaseous substance that envelopes the earth and forms its atmosphere. It is remarkable in the constancy of its composition; for while this is being continually changed as the result of the respiration of men and animals, and by addition of gases arising from organic changes and the products of combustion, it is ever being brought back to normal and the proper balance restored by the processes of plant and vegetable life. Nature sees to it that the air in which we live and breathe is kept purified. This does not apply to the air in a coal mine, where there are no natural forces to change and make use of the different gases formed or evolved, and where mechanical ventilation is the only effective means of keeping the air pure. The atmosphere consists of oxygen and nitrogen, not in the combined state but merely mixed. By volume, the composition is: oxygen, 21 percent, nitrogen, 79 percent, there being included with the latter small quantities of such substances as water vapour, carbon dioxide, nitric acid, ammonia, ozone, argon, neon, and organic gases. Of the two principal gases which form air, oxygen alone supports life. When air is inhaled into the lungs the oxygen is absorbed by the blood, which carries it through the body to nourish and energize it. Exhaled air consists of water vapour and about 4 per cent carbon dioxide, with from 16 1/2 to 17 per cent oxygen and 79 per cent nitrogen; the oxygen alone having been drawn on to any considerable extent.

Jan 1, 1930

By T. G. Joseph, A. Sharma

ABSTRACT: Ultra-class haul trucks operating in oil sand face operational and maintenance issues as a result of soft underfoot conditions (Joseph, 2002). With exposure to frequent high g loading events, tire life is reduced due to sidewall belt fexure and frequent ground contact. Therefore, an improved under-standing of the interaction between tires and oil sand is needed. This paper examines the outcomes of a series of static and cyclic loading tests, performed using a scale tire on rigid, sand, and oil sand surfaces. Geometric predictions are made regarding the footprint area and vertical deformation of an ultra-classtire on similar surfaces.

Jan 1, 2011

By M. Aushouri, S. H. Mansouri, N. Aminizadeh

A thermo-chemical model of the Peirce-Smith copper converter in blowing the copper stage has been developed to predict the molten temperature. The key assumption of the model was that white metal and gas phases in the converter were in thermal and chemical equilibrium. In this model, the chemical reaction of white metal and oxygen was accomplished completely. So long as sulfur existed in the bath, the generation of Cu2O was frozen. The reaction rate was considered to be constant and controlled by the reacted sulfur. The converter temperature was calculated by heat balances over time. The model was validated by a detailed comparison with measured industrial data. A good agreement was obtained. The converter temperature depended on process parameters such as oxygen efficiency, molten emissivity and oxygen enrichment.

Jan 1, 2007

By James J. Scott

"In the two years since their introduction, Friction Rock Stabilizershave replaced40 per cent of the previously used fixtures in the metal and non-metal mines in the United States. The Friction Rock Stabilizer, or ""Split Set "" , is a mechanical rock stabilizing system which uses friction to prevent rock movement . The Split Set is a tapered, rolled, steel tube that is slotted along its length. As it is driven into a drilled hole smaller than its diameter, it compresses, pre-loading the surrounding rock. This paper discusses the uses and acceptance of the friction rock stabilizer in mines in the United States. IntroductionFriction Rock Stabilizers, commonly called Split Set™· Stabilizers, have been under development by the author and Ingersoll-Rand Company since early 1973. Five years of intensive laboratory and field testing led to their introduction to the metal mines in the United States in the fall of 1976. Actual sales started in February of 1977and, to date, over five million units have been marketed to metal mines. The present rate of usage is near 3 V2 million units per year, which is approximately 50070 of all roof fixtures used in the United States metal mining industry,Richard Hoppe, senior editor of Engineering & Mining Journal. , in an article in the February 1979 issue entitled ""Winning the Battle Against Bad Ground"", said: ""In hardrock mining operations in the western U.S., particularly underground uranium mines where exceedingly difficult ground is common, no roof support system has been accepted more quickly than the Split Set friction bolt invented by Dr. James J . Scott and developed by Ingersoll-Rand Co."" This paper describes how Friction Rock Stabilizers function and presents technical data to show the uniqueness of such systems."

Jan 1, 1980

By R. Lodha, C. Oprea, G. Oprea, H. Zargar, T. Troczynski

"The basic refractories used in non-ferrous industry contain chrome ore for improving the thermal shock resistance, thus reducing the penetration of molten metal and fayalite-type slags into the lining. The current study aims to replace chrome ore with Me4+ ions along with Fe3+ ions in order to form MgO-Al2O3- FeOx-Me4+O2 based complex spinel systems that could perform similar to the complex chromia-bearing spinel in the magnesia-chrome refractories. This system allows for lower temperatures of synthesis and sintering. In our study, compositions with 60% MgO were fired below 1500°C and resulted in complete formation of complex spinel, and open porosity less than 5%. The in-situ formation of the complex spinel from the fine mix of oxides in the MgO-Al2O3-FeOx-Me4+O2 system offers a suitable alternative of binding system to produce basic refractories at lower temperatures and of similar physical and mechanical properties with magnesia-chrome bricks fired above 1750ºC. INTRODUCTIONThe synthesis of magnesium aluminate spinel (MgAl2O4) (Maschio, Fabbri, & Fiori, 1988) or magnesium chromate spinel (MgCr2O4) from their respective oxides is diffusion controlled resulting in a sluggish reaction even at high temperatures. For instance, the diffusion of Mg2+ and Al3+ ions in the intermediate spinel layer during reaction is slower than the diffusion of Mg2+ in corundum and Al3+ in periclase. The interfacial layer of spinel formed during the reaction increases the diffusion path for the spinel forming cations. This accompanied by ~8% volume expansion retards further reaction resulting in incomplete spinel forming reaction during sintering and hence densification during the reaction cannot be achieved. In order to assess sintering studies with fine particulate oxides that would result in a lower diffusion path, a mechanical mixture of the hydroxides of aluminium and magnesium calcined at 1400ºC to 1600ºC for 1 hour does not result in complete spinel formation (Sarkar, Das, & Banerjee, 2003), which indicates that reaction sintering of stoichiometric magnesium aluminate spinel is retarded by initial reaction forming the interfacial spinel layer. The basic bricks used as linings in non-ferrous pyro-metallurgical convertors are manufactured using magnesia and chrome ore, the sintering of which produce spinel solid solution. This solid solution is a mix of both normal and inverse spinel structures that sinters at temperatures in excess of 1800ºC in air."

Jan 1, 2012

By V Dolmage

Copper Mountain is the third largest copper mine in British Columbia, and is now producing close to 20 million pounds of copper per year, with which is recovered also 4,000 ounces of gold and. 13,800 ounces of silver. After a long and checkered career, during which the ownership and management changed several times, this deposit finally came into the possession of the Granby Consolidated Mining, Smelting and Power Company in 1923. It was not, however, until the end of 1925 that the mine, under the management of Charles Bocking and C. H. Smith, was successfully placed on a basis of profitable production. It is a low-grade deposit of the contact-metamorphic type, with refractory ores consisting of chalcopyrite and bornite in a gangue of altered andesitic and basaltic breccia. The ore is concentrated to a product carrying over 30 percent copper, which is smelted in Tacoma. The deposit is 12 miles south of the town of Princeton, which is on the Kettle Valley railway, 150 miles east of Vancouver and 40 miles north of the International Boundary line. Princeton is served also by a branch of the Great Northern railway, which leads clown the Similkameen, Okanagan, and Columbia valleys. Copper Mountain mine and camp are connected to Princeton by a good mo tor road extending up Wolf Creek valley, while the haulage level of the mine, which emerges on the steep side of the Similkameen valley 1,000 feet below the camp, is connected with Princeton by a spur of the Kettle Valley railway leading up the Similkameen canyon and passing en route through Allenby, where the concentrator is situated.

Jan 1, 1929

By H. R. Oliveira, C. R. Aragonez de Vasconcellos

Pipeline operation and maintenance necessarily involves geotechnical studies at points and areas with deflagrated instabilities or still to map and monitor areas prone to geotechnical problems. Landslides, erosions and debris flows are some examples of natural hazards, that not rarely, can bring high consequences to pipelines, sometimes leading them to high stresses levels and ruptures. Bolivia-Brazil Natural Gas Pipeline has 2.593 kilometers since Rio Grande City in Bolivia until Canoas City, in south Brazil. The pipeline crosses a lot of types of geological fields and difficult topography. The south spread of the pipeline has the most prone areas to geotechnical hazards because of its hard topography combined with the variety of geological materials, such as, colluvium deposits and debris flow areas. The aim of this paper is to present the right-of-way geotechnical risks that affect pipelines, presenting some practical remedial works done by TBG at Bolivia-Brazil Natural Gas Pipeline as well as the integrity plan and the adopted actions in way to prevent geotechnical accidents.

Jan 1, 2005

"In the present study, the reduction behavior of composite pellets comprising of iron oxide, synthetic graphite and slags were investigated in a laboratory-scale horizontal tube furnace. Two different types of slags indicating silicate base and aluminate base slags were chosen to examine the effect of slag chemistry on the reduction behavior of pellets. Slag composition of binding materials has influences on the reactions occurring in composite pellets during direct reduction. In-situ high temperature visualization approach was used to observe the slag / iron / carbon interactions at 1773K (1500°C). The off-gases were measured by means of infrared analyzer to determine the reaction rates of the pellets. Different physical appearances during the in situ reaction inferred a strong correlation between the slag composition and internal reactions. In addition, compression tests were conducted to examine physical strength of the pellets. This investigation was carried out to establish feasibility of physical property control of pellets by selecting optimum slag compositions of binding materials INTRODUCTIONCurrently, most of the iron ore mines have facilities that make an ore more usable for the blast furnace operation by improving its physical properties (e.g. pelletizing and sintering). However, during the process, a large amount of fuel is supplied to indurate materials which consequently deteriorate energy efficiency and produce more CO2 emission. Along with increased interests, direct reduced iron (DRI) making process; simply without coke oven or sintering process, has opened the era of clean and environmental friendly iron making process. While some of the established DRI technologies such as Midrex and HYL were restricted to certain locations where natural gas is abundant, coal based technologies using Rotary Hearth Furnace (RHF) such as FASMET and ITmk3 have been developed with regardless of expensive fuel deposit. In addition to the direct use of pulverized non coking coal and fine iron ore, RHF process also has advantages of utilizing waste materials such as EAF dust, biomass and recycled plastics. Nevertheless, there are still many challenges in the coal utilizing technologies as the unprocessed coal and the waste materials contain huge volatiles and ashes. Although recent investigations on volatiles in a RHF process (Sohn and Fruehan, 2005, 2006) have indicated the benefits of coal in terms of iron oxide reduction and have shown feasibility of multi-layer process, carbon composite pellets still have disadvantages because of its weak mechanical bonding strength. As the mixed system with carbon and oxides generates intermediate gases (e.g. CO and CO2) between solid particles, it is difficult to keep its physical state without the help of binding materials. In this reason, industries have been tried to use various binding materials such as bentonite, kaolinite and Portland cement. However, they are still struggling to find out new materials that provide not only sufficient mechanical strength but also metallurgical properties, such as porosity, reducibility and swelling throughout the reduction reaction. Recently, Canadian researchers (Aota et al, 2006) observed enhanced mechanical strength of pellets by using high alumina cement as a binder and concluded that the method could be used to recycle EAF dust as well, but in depth mechanism of reinforced strength has not been concerned. Most of the ashes coming from binders formulate certain type of slag during the reduction process due to its incombustibility. Thus, observation and regulation of slag property is an essential for the control of carbon composite pellet. Yet, only a little thermodynamic consideration from the perspective of slag chemistry has been adapted in the iron and steel making industries as ash has been easily ignored for its tiny proportion. In this study, effect of CaO-SiO2- Al2O3 slag system on the reduction of iron oxide was investigated in terms of"

Jan 1, 2012

By P. Nayak

"Comminution is an energy intensive and expensive process consuming approximately 40-50% of the total processing costs in a mining operation. This process poses an even greater challenge with gold ores due to their low elemental concentration and small particle size. Over 99.9% of the ore fed to the mill is waste which must be removed during the ore processing stage. Preconcentrating the Run of Mine (ROM) ore before feeding the mill will result in significant cost savings. In partnership with Sacré-Davey Engineering, Agnico Eagle Mines Limited identified this opportunity and is currently evaluating the implementation of sorting technology to preconcentrate the ore or upgrade the waste material at its operations. This paper will discuss the steps adopted by Agnico Eagle in the evaluation and installation of sorting technology at its operations. Since the Company has a large portfolio of operations, the first step in the project was to shortlist the operations that had the highest probability for successful application of the technology. Following this, the top three operations were selected for bench scale evaluation. The projects which showed the most economic potential were then considered for detailed evaluation and pilot plant installations. This paper provides an insight into the methodology followed by Agnico Eagle and Sacré-Davey in the evaluation of the technology.INTRODUCTION The benefits of ore sorting technology are being increasingly understood by the mining industry today. The application of ore sorting in gold mining is attractive due to the nature of the mineral distribution. The presence of high value minerals distributed in an extremely small mass of the ROM ore creates a tremendous opportunity for preconcentration with ore sorting. Since Agnico Eagle currently has a portfolio of eight operating mines and numerous development projects and exploration properties, the challenge was to identify the deposits which had the most favourable mineralogy and grade distribution for successful ore sorting. The success of ore sorting is mostly based on the minerals present in the deposit and the grade distribution. The minerals signify the amenability of the deposit for ore sorting and the kind of sensing technology to be used. On the other hand, the grade distribution demonstrates the amount of material that can be rejected without losing value. In order to understand a deposit’s characteristics, it is important to examine the sample’s behaviour with various sensors and then assay it to know its actual value. It is a common practice in the mining industry to document assay value of drill cores and/or material feeding in and out of the mill. However, those VALUES (are insufficient to understand the grade variability on a granular basis. To capture the ore variability in very high resolution and significantly improve the selectivity of the material feeding the mill, it is vital to assay the samples on a rock-by-rock basis, as this is the level of resolution which will be examined by the ore sorter during sorting. A careful and elaborate procedure was followed in evaluating the technology at Agnico Eagle’s operations which is discussed in this paper."

Jan 1, 2019

By Dong-min Lee

As the construction industry is becoming more large-scaled and complex, the BIM technology has been utilized throughout the industry. Since 2008, the construction industry in South Korea (Korea) has required carrying on BIM-based project continually. According to this trend, BIM S/W market, as well as BIM library market is also gradually activated. Many countries have already been establishing Web-based BIM library market, also Korea has been trying to establishing this Web-based BIM library market. In this study, through market research of Web-based BIM library market of advanced countries including the U.S.A. and U.K., establishment strategy of BIM library market to be derived by late starters that introduce BIM such as Korea, Japan and China was deduced based on current establishment status of BIM library market in Korea. In addition, deal with an issue that a clear revenue-sharing system between business principals of Web-based BIM library market is not available at the current stage was presented as a factor of inhibiting activation of BIM library market. So in order to offer a reasonable revenue-sharing strategy in BIM library market as conceptual level, a methodology and process of applying Game theory being used for deriving. It is expected that a reasonable revenue-sharing model between business principals would be presented as its standard of BIM library market to be more activated in the future.

Aug 1, 2013

By Hyumng Sup Choi

The role of the interfacial electrical 'Condition on the adsorption of col-lectors on mineral surfaces has been studied by electrophoretic mobility and adsorption measurements made on zircon. From the investigation of the electrokinetic properties of zircon, H+ and OH-are seen to act as potential determining ions, thus controlling the electrical nature of this mineral. The isoelectric point of zircon occurs at a pH of approximately 5.0, and it is evident, therefore, that the zircon surface would be positively charged below a pH of 5.0 and negatively charged above this pH. The adsorption of collectors therefore de-pends strongly on the pH of the solution; anionic collectors are adsorbed on positively charged surfaces and cationic collectors on negatively charged surfaces. This, in turn, de-fines the effective flotation condition, with respective collectors, for this mineral. The above results have been correlated with the flotation behaviour obtained by the simplified flotation test using a modified Hallimond tube.

Jan 1, 1963