Search Documents

By C. S. Barrett

It has been observed that deformation in iron takes place by slip on (110) + {112) + (123) planesl, 2, but in silicon ferrite with low deformation temperatures or high silicon contents (exceeding 4 per cent) the authors have found that slip is confined wholly to (110) planes, at least with small amounts of deformation. The purpose of the present investigation was to determine the effect of this alteration of slip mechanism on preferred orientations in cold-rolled and recrystallized strips. Incidental observations on the effect of the recrystallization temperature were also made. The numerous determinations of the texture of cold-rolled iron and steel have been in satisfactory agreement as to the principal features of the texture (with the exception of a few conclusions that apparently have been based on insufficient data). The texture is chiefly one in which 11101 directions of the grains lie along the direction of rolling, with a deviation of a few degrees, and in which the (100) planes lie in the plane of the rolled sheet, with a deviation from this position chiefly about the rolling direction as an axis. This deviation about the rolling direction as an axis has been measured by different observers and lies between about 45" and 50" or 60" for iron5, 6, 9 and is usually in the neighborhood of 50" for mild stee16, 7, 8. The range of this deviation is a function of the percentage of total reduction8, 10. Post8 reported that it decreases with increasing percentage reduction, but apparently he studied only the surface material, which Gensamer and Meh17 found to be somewhat differently oriented from the material in the inside of the sheet. McLachlan and Davey10 found that the deviation also decreases with increasing percentage of total reduction for the material in the interior of the sheet and is independent of the percentage of reduction per pass. The deviation about the cross direction as an axis (the direction in the

Jan 1, 1937

By F. O., Garrabrant

ELECTRIC power requirements for Climax are similar to those of most metal mines, except that large blocks of power are used underground and there are a number of other unusual applications. Power is furnished to the Company by the Public Service Co. of Colorado over two 100,000-volt lines to a bank of three 3333-kva. transformers 100/13.8 kv. These transformers are designed so that with the addition of forced cooling their capacity may be increased a third at 12,000-ft. altitude. On the secondary side of this bank is a 15-kv., 1200-amp. oil circuit breaker provided with automatic reclosing relays allowing three successive short circuits before lockout. From this breaker 13.8-kv. power is transmitted to a central switching station where all circuits radiate to the different operations of the property. Each circuit is protected by a 23-kv., 600-amp. oil circuit breaker with by-pass and isolating disconnecting switches. (A more complete description of the electrical distribution system at Climax, with detailed drawings, is contained in T.P. 1734, A.I.M.E., Mining Technology, July, 1944.)

Jan 1, 1946

By E. V. Potter, E. T. Hayes, H. C. Lukens

LARGE volumes of hydrogen are liberated at the cathode during electrolytic precipitation of manganese. Most of the gas escapes from the electrolyte, but a considerable amount may be entrapped in the manganese plate. Gas has been observed to escape from manganese melts in puffs that ignite at the surface. It has been reported that castings made with electrolytic manganese tend to rise in the molds; for this reason the manganese is often treated to remove hydrogen before the melt is made or it is premelted and used as cast manganese in making the alloys. The effect of hydrogen on the properties of manganese and its alloys is not known, but its effect on iron and iron alloys has been studied extensively.1.2 The close relationship between iron and man¬ganese suggests that hydrogen may have a similar effect on the properties of manganese and its alloys. The purpose of this investigation was to determine the amount of hydrogen or other gases in typical commercial electrolytic manganese sheet and to investigate ways of removing it most conveniently. APPARATUS The apparatus used is shown schematically in Fig. I. It consists of a chamber A in which the metal sample is placed, a vacuum or pressure gauge B, volume gauge C, vacuum pump D, hydrogen container E, auxiliary gas chamber F, and furnace G. The specimen chamber was made of two concentric quartz tubes. The outer one, a, connects with the closed gas system and is surrounded by the furnace G. A second tube, b, fits closely inside a and has a small end that projects into the space for the specimen and holds the thermocouple for measuring the temperature of the sample. The inner tube is joined to the outer tube outside the furnace, with rubber tape and sealing wax, to prevent gas leakage into or out of the closed system. This type of specimen container is loaded very easily and can be used several times if molten metal does not come in contact with the quartz. An ordinary mercury manometer B is used to measure the pressure in the system. The volume gauge C is essentially another mercury manometer, but the volume of the column is much larger than normal and the height of the mercury can be varied by raising or lowering the well H. In this apparatus the tube had a volume of I00 c.c. for a 60-cm. length. For larger changes in gas volumes; auxiliary containers F were used to increase the volume of the system by known amounts. Valves were arranged so that these auxiliary containers could be filled from the system and evacuated by the pump as often as necessary to accommodate the increases in the volume of gas in the system. The furnace G, used to heat the samples, was equipped with an automatic temperature controller, which maintained the desired temperatures within ± 5°C.

Jan 1, 1945

By Howard Willey

Mining operations of the Charcas unit at present are limited to the Tiro General mine at Charcas, in the State of san Luis Potosi, Mexico. The Tiro General mine was first operated during the Spanish occupation of Mexico for rich silver ores in an oxidized zone along the outcrop of the principal vein. In depth the ore is a complex sulfide with widely varying proportions of sphalerite, argentiferous galena and chalcopyrite ; and until recent years, it was economically impossible to carry on mining otherwise than irregularly in sections of the veins richest in galena and chalcopyrite. The advent of selective flotation brought the orebody as a whole within the field of economic interest, and a flotation mill of 650 metric tons daily capacity was constructed in the year 1925. The mining of partly worked-out sections of the mine, as well as the very heavy ground in most of the stopes opened in virgin ore, presented an unusually difficult problem. This paper describes the so-called "filled top slice" stoping method finally adopted as the standard system. Physical and Geological Conditions The principal orebody of the mine is an oreshoot about 1400 ft ng in a fissure vein striking about east and west and with an average lip of 70" to the north. The footwall of the orebody is fairly cleancu and regular both longitudinally and vertically and generally shows a dell-marked post-mineral slip. The footwall rock varies from a fairly strong limestone to a broken, metamorphosed limestone which requires heavy timbering. In some sections it is an altered, crumbly porphyry, which swells badly and necessitates frequent renewal of drift and raise tirnber. The hanging wall is irregular and frequently an assay wall. The stopina width ranges from a few feet up to more than 90 ft.; it averages about 30 ft. For the most part the hanging-wall rock is a shattered and altered monzonite porphyry, nearly aways requiring heavy timbering. The orebody is greatly fractured by post-mineral movement, which usually followed the footwall and left it as a smooth surface frequently covered with a slippery clay gouge. Two well marked transverse faults

Jan 1, 1931

By J. A. Berger, R. J. Towner

A method for determining the disorientation between sub-grains that .share a common tilt or twist boundary from measurements on X-ray micrographs is described. The method may be applied to subgrains of almost any orientation having boundary angles in the range from about 1 min to 1 deg of arc. An adaption of the Berg-Barretl method has been made to allow calculation of small angles of about 1 min to 1 deg of arc: between adjacent subgrains from the relative displacement of their images on X-ray micrographs. schulz4 gave equations for determining subgrain disorientation where the axis of subgrain rotation and the reflecting crystal planes were parallel to the specimen surface. In our method, however, they need not be parallel and, indeed, may have va:rious orientations. His camera setup, involving a fine-focus X-ray tube for obtaining high resolution with continuous radiation, was different from the one used in the present investigation (a 1.2 x 1.2 mm effective source and characteristic radiation). The X-rays produced a slight magnification in the subgrain images in the Schulz method, but not in the present method. The commonly available type of X-ray tube used permitted relatively short exposure times with a fine-grained photographic plate, which could be magnified optically many times for the examination of small subgrains. The method is illustrated by results obtained on {110} tilt boundaries in a polygonized aluminum single crystal of 99.994 pct purity. The flat crystal was stretched 6 pct in tension and then heated at 500°C for a cumulative time of 5 hr. Earlier, cahn5 studied subgrains formed by polygonization in stretched and heated aluminum crystals. He observed kink bands to have well defined boundaries lying in (110) planes, at least in the early stages of deformation. Cahn found that the (110) tilt boundaries formed by polygonization were directly related to the lattice bending about the <211> axis which lay in the (111) slip plane perpendicular to the <110> slip direction. DESCRIPTION OF THE CAMERA Our camera was similar in detail to Honey-combe&apos;s.6 Unfiltered copper radiation was used at 35 kv, and 20 ma. With the particular specimen used here to illustrate the method, a 1.2 by 1.2 mm effective source and a distance of 780 mm from target to specimen were employed, giving a convergence of 5 min of arc in the primary beam. The distance was 9.5 mm from the specimen to film. The upper 1/2- by 1-in. portion of the front surface of the specimen was irradiated with the film in parallel position. Since the specimen had been inhomogeneously deformed, many regions were in a position to reflect characteristic radiation at the Bragg Angle. Five minute exposures were satisfactory with Kodak Single Coated X-ray Film, 1 1/2 hr

Jan 1, 1961

By P. D. Merica

MY remarks are addressed to the question whether a program of international mineral control can effectively serve as a means of maintaining world peace in the kind of world envisaged by the Atlantic Charter. They do not touch the quite different questions whether such control could be appropriately used for postwar punishment of Germany and Japan, or for other purposes. I assume also that the question relates, not to the transition period immediately following the war, but to the more normal years which we hope will succeed this. Finally, they deal primarily with metals and metallic minerals rather than with. oil or coal or other minerals, although they may be applicable also to these other nonmetallic materials.

Jan 1, 1944

By C. S. Yust, J. W. Smith, J. R. Walsh, R. E. Simpson

This paper presents the results of a complete reservoir studv designed to determine a sound economic program for the conservation of oil and gas in the Pickton field, Hopkins County, Texas. The Pickton field produces from the Bacon Lime with all indications of the study being that production is predominately by dissolved-gas drive. Calculations of the total ultimate recovery to be expected under primary operations indicated only 16.7 per cent of the oil originally in place would be recovered. This unusually low recovery is due to the type of drive operating and the extremely high dissolved gas-oil ratio and shrinkage. Results are presented for six plans of returning gas to the reservoir, evaluated to determine (1) comparative recoveries and economics of (a) returning gas at a constant rate by supplementing Pickton gas with extraneous gas during the early portion of the operation, and (b) conventional gas-return operations without using extraneous gas, and (2) the optimum size of compressor plant for each type of pressure maintenance. The over-all economic program considers, for either type pressure maintenance operation. a gasoline plant to process the unusually rich casinghead gas. Since pressure maintenance will disturb equities, pooling of royalties is in the case of Pickton a prerequisite to conservation of oil by this type of operation, both from an economic and legal standpoint. In the event pooling of royalties cannot be achieved, the study considers a gasoline plant to operate under a modified primary production operation which will make the conservation of gas possible. INTRODUCTION The Pickton field, located in Hopkins County, Texas. was discovered in November, 1944. by the completion of Humble&apos;s C. D. Nichols 1, in the Bacon lime of the Lower Glen Rose formation, through perforations from 7,888 to 7.896 feet. The well initially produced 50.2 API gravity oil with a gas-oil ratio of 1,350 cubic feet per barrel. Subsurface samples of the reservoir fluid obtained soon after completion of the discovery well showed that the Pickton crude is unique in that it has an extremely high dissolved gas-oil ratio and is subject to very severe shrinkage. Calculations of the future behavior of the Pickton reservoir indicated that ultimate oil recovery by primary operations would be 3,269,000 barrels, representing only 16.7 per cent of the oil in place (19,577,000 stock-tank barrels), and that recovery could be substantially increased by returning the produced gas. The cumulative production of 1,382,694 barrels on November 1: 1947, amounted to 42.3 per cent of the estimated ultimate oil recovery from primary operations. The purpose of this study is to determine and evaluate the optimum program for conservation of oil and gas in the Pick-ton field, including the desirability of conducting gas-return operations and of installing a gasoline plant. LOCATION AND DESCRIPTION Pickton Field, The Pickton field, as shown in Fig. 1, is located in southwest Hopkins County, Texas, 12.5 miles southwest of the New Hope field, 2.7 miles northeast of the Coke field, 16 miles southwest of Sulphur Springs, and 8 miles northwest of Winnsboro, Texas.

Jan 1, 1949

By C. S. Yust, J. W. Smith, J. R. Walsh, R. E. Simpson

This paper presents the results of a complete reservoir studv designed to determine a sound economic program for the conservation of oil and gas in the Pickton field, Hopkins County, Texas. The Pickton field produces from the Bacon Lime with all indications of the study being that production is predominately by dissolved-gas drive. Calculations of the total ultimate recovery to be expected under primary operations indicated only 16.7 per cent of the oil originally in place would be recovered. This unusually low recovery is due to the type of drive operating and the extremely high dissolved gas-oil ratio and shrinkage. Results are presented for six plans of returning gas to the reservoir, evaluated to determine (1) comparative recoveries and economics of (a) returning gas at a constant rate by supplementing Pickton gas with extraneous gas during the early portion of the operation, and (b) conventional gas-return operations without using extraneous gas, and (2) the optimum size of compressor plant for each type of pressure maintenance. The over-all economic program considers, for either type pressure maintenance operation. a gasoline plant to process the unusually rich casinghead gas. Since pressure maintenance will disturb equities, pooling of royalties is in the case of Pickton a prerequisite to conservation of oil by this type of operation, both from an economic and legal standpoint. In the event pooling of royalties cannot be achieved, the study considers a gasoline plant to operate under a modified primary production operation which will make the conservation of gas possible. INTRODUCTION The Pickton field, located in Hopkins County, Texas. was discovered in November, 1944. by the completion of Humble&apos;s C. D. Nichols 1, in the Bacon lime of the Lower Glen Rose formation, through perforations from 7,888 to 7.896 feet. The well initially produced 50.2 API gravity oil with a gas-oil ratio of 1,350 cubic feet per barrel. Subsurface samples of the reservoir fluid obtained soon after completion of the discovery well showed that the Pickton crude is unique in that it has an extremely high dissolved gas-oil ratio and is subject to very severe shrinkage. Calculations of the future behavior of the Pickton reservoir indicated that ultimate oil recovery by primary operations would be 3,269,000 barrels, representing only 16.7 per cent of the oil in place (19,577,000 stock-tank barrels), and that recovery could be substantially increased by returning the produced gas. The cumulative production of 1,382,694 barrels on November 1: 1947, amounted to 42.3 per cent of the estimated ultimate oil recovery from primary operations. The purpose of this study is to determine and evaluate the optimum program for conservation of oil and gas in the Pick-ton field, including the desirability of conducting gas-return operations and of installing a gasoline plant. LOCATION AND DESCRIPTION Pickton Field, The Pickton field, as shown in Fig. 1, is located in southwest Hopkins County, Texas, 12.5 miles southwest of the New Hope field, 2.7 miles northeast of the Coke field, 16 miles southwest of Sulphur Springs, and 8 miles northwest of Winnsboro, Texas.

Jan 1, 1949

By H. N. Hall

Various factors must be considered in an engineering evaluation of gravity-drainage reservoirs. Among these are: (1) the effect of producing rate on total oil recovery; (2) the effect upon well productivity and ultimate recovery of the pressure level maintained during the producing life of the reservoir; (3) the economic advantage of full or partial pressure maintenance; and (4) estimate of the rate of gas production and injection and the possible purchase of gas under conditions of full pressure maintenance to ascertain compressor facilities needed. All of these factors can be evaluated only when a reliable method is employed for determining reservoir performance in gravity-drainage reservoirs. The purpose of this paper is to present a general method for calculating the performance of a gravity-drainage reservoir. This method is applicable for conditions of complete pressure maintenance, partial pressure maintenance and normal pressure depletion. Provisions are made to take into account variations throughout the reservoir of reservoir configuration, changes in permeability and fluid composition. Based on the method presented in this paper, an IBM 650 computer program has been developed. The past performance of an actual gravity-drainage reservoir producing under conditions of declining pressure and no gas injection was duplicated using this program. INTRODUCTION In tilted reservoirs the production of oil is influenced by drainage of oil from upstructure to downstructure locations. When this downstructure drainage of oil is sufficient to cause effective segregation of the gas and oil in a reservoir, the reservoir is usually classified as a segregation drive or gravity-drainage reservoir. (Discussion will be restricted to gravity-drainage reservoirs which have no encroachment of edge water.) The important feature in gravity-drainage reservoirs is the density difference between reservoir oil and gas. These phases tend to segregate in the reservoir with the result that in the gas cap the oil saturation is maintained at a higher level by drainage of oil from the gas-cap area. Oil can be produced from the oil zone at a low gas-oil ratio and reservoir energy is thereby conserved. The standard material balance in not adequate for predicting gravity-dramage reservoir performance because it does not take into account the difference in saturation above and below the gas-oil contact. Several authors&apos;.&apos; have presented methods for calculating the performance of gravity-drainage reservoirs in which reservoir pressure is maintained constant by gas injection into the gas cap. Using some simplifying assumptions, these methods can be employed with a desk calculator to give acceptable results. The problem of predicting the performance of gravity-drainage reservoirs under the conditions of declining reservoir pressure is many time more complex than that of constant pressure. fierefore, attempis to develop a method suitable for desk calculation have required excessively simplified assumptions. In the past several years, highspeed digital computers have become more widely available for reservoir engineering problems. These corn puters are well suited to problems such as the prediction of the performance of gravity-drainage reservoirs with pressure decline. Many of the simplifying assumptions necessary for hand computation can be eliminated so that a realistic approach to the gravity-drainage process can be made. CONCEPTUAL PICTURE OF OIL MOVEMENT IN GRAVITY-DRAINAGE RESERVOIRS Before attempting to develop an analytical treatment for conditions occuring in a gravity-drainage reservoir, a concept should be formed concerning the movement of fluids in the reservoir as oil is produced. A review of the literature&apos;.&apos; shows that it is customary to classify gravity-drainage operations into two categories—(1) with complete pressure maintenance, and (2) with declining pressure. The same line of reasoning will be followed in presenting the concept of the movement of fluids in the reservoir because it is easier to visualize the movement of fluids under conditions of complete pressure maintenance. After discussing complete pressure maintenance, an analogy will be made between that and the case of declining pressure. It should be kept in mind throughout that the final aim for the problem of solving gravity-drainage performance with digital computers will be to develop a general program for any kind of gravity-drainage reservoir. COMPLETE PRESSURE MAINTENANCE One feature which is generally common in gravity-drainage reservoirs is a gas cap located at the top of the structure. This is shown in Fig. 1(a). Fig. l(b) shows oil saturations that might occur through the reservoir. In the gas cap, oil saturation is lower than

By W. E. Keck

THE potential iron ores of Michigan can be classified from the stand-point of the predominant impurities into siliceous, sulphurous and phos-phorous ores. Research on the flotation of each of these classes of ore was carried out in the following Planner. The flotative properties of the valuable minerals of iron and of the worthless and deleterious ones were first determined under carefully controlled conditions. This information was then applied to synthetic mixtures of these minerals, which simulated the potential ores. Finally, data obtained during the two foregoing stages of the investigation were used in the flotation beneficiation of samples of the potential ores. Hematite is the most important mineral of iron in each of the above classes of iron ores. This paper deals with a study of that mineral in the very nearly, pure state. There are two varieties of the mineral-specular hematite and massive hematite. The latter is the principal variety, but the former is an Impor-tant mineral of iron in some of the potential ores. Because of this condi-tion, flotation research was performed with both varieties. This research consisted essentially of: (1) a survey of the literature on hematite flota-tion, (2) the preparation of pure massive hematite, (3) the preparation of pure specular hematite, (4) the; development of a laboratory procedure and (5) flotation experimentation. For the purpose of this discussion, the results of previous work on the flotative properties of hematite can be summarized as follows: Specular hematite has been readily floated with terpineol and sodium oleate or heptylic acid1. Further, hematite has been likewise floated with a pro-prietary frother and oleic acid or other soluble oils 2. Finally, lead nitrate, copper sulphate, silver nitrate, chromium nitrate, mercuric chloride, ferric

Jan 1, 1937

New York Meets first Wednesday after first Tuesday of each month. J. E. JOHNSON, JR., Chairman EDGAR RICHARD, Vice-Chairman D M LIDDELL Secretary, 7 Wall St.. New York. N. Y. C. A. BORN, Treasurer JOHN V. N. DORR LEWIS W. FRANCIS Boston Meets first Monday of each winter month. R. L. AGASSIZ, Chairman JAMES G. CARLETON. Vice-Chairman E. E. BUGBEE Secretary-Treasurer, Mass. Inst. of Technology, Cambridge, Mass. W. E. C. EUSTIS G. A. PACKARD Columbia Holds four sessions during year. Annual meeting in September or October. W. H. LINNEY, Chairman OSCAR LACHMUND, Vice-Chairman LYNDON K. ARMSTRONG, Secretary-Treasurer, P. O. Drawer 2154, Spokane, Wash. STANLY A. EASTON S. SHEDD

Jan 12, 1917

The opening session was held on Tuesday evening, June 28th. Mr. F. S. Witherbee, of Port Henry, a member of the Local Committee, welcomed the Institute as follows: Mr. President and Gentlemen and (if I my also add) Ladies of the Institute: In the absence of the Chairman of our Local Committee it is my pleasant duty to give you a cordial welcome once more to the shores of Lake Champlain. I think some fourteen years have passed by since we last had the pleasure of receiving you at a meeting in this vicinity ; but the pleasure of that meeting still lingers in our memory; and the profit which we derived from your discussions and from your presence with us has made us heartily desirous to have you here again. If the truth must be known, we were for a time much embarrassed by the difficulty of providing adeqriate and comfortable shelter for the large number of friends whom we hoped (and, as this assembly indicates, had good reason for hoping) to receive. But the liberality and zealous co-operation of the Delaware & Hudson Canal Company and its hotel manager, in offering to open Hotel Champlain, at no little inconvenience, before the usual time, presented a solution of this difficulty, provided the date originally proposed for the meeting could be changed to a week later. This change was duly authorized; .and I think you will all agree with us that it was wise.. At all events, I am sure, I now need offer no apologies for the roof which covers yau. During the fourteen years which have elapsed since your last visit to us, great strides have been made in the industrial development of this country. The meetings of the Institute, held from one end of the land to the other, have permitted you to witness the transformation of small hamlets? like Birmingham, Ala., into populous and thriving industrial centers. You have seen the Minnesota and the

Jan 1, 1893

By L. D. Clark, S. S. Saluja

A physical law, governing the rupture of rock by confined explosive charge correspondent to current expressions for determining weight of charge to rupture rock burden, W, was developed in the form Q = cVw3 by two early investigators performing unique experiments with ice. The coefficient C, is found by trial blast. Recent physical tests conducted with rock, synthetic materials and ice to establish the validity of the theory on which it and other related formulae are based indicated: (a) that failure under hydrodynamic impact pressure is by tension rather than shear as was assumed; (b) that the fundamental law of mechanics, enabling the determination of Q = cvw3, modified to the form P = R x Sa x Wb is valid when low velocity explosives are used; (c) that rock breakage under the action of low velocity explosives is entirely due to explosion gas pressure, as was believed; (d) that under the action of high velocity explosive it is due to the joint effects of scabbing and gas pressure; and that further possible modification could make the above equation also applicable to these joint mechanisms. shape could be easily frozen and because large loads would not be required. They found: (a) that the not unfamiliar shearing equation for metals was applicable to ice where P = load in lb; S = periphery of pressure surface, in.; W = burden, in.; K = modulus of rupture by shear in lb per in.2; and (b) that "the form of cavity produced by the application of gradual pressure is similar to that obtained by blasting in rock under similar conditions of free face and pressure surface!" This similarity in crater shapes leads to the conclusion that rock would rupture by shear, as did ice, and its behavior under the force of a blast could be governed by such a relationship as P = S x W x K. Three important interrelated empirical expressions were derived and rock, charging and spacing coefficients C,, C, and e were established and substantiated by trial blasts. In checking the accuracy of the main assumptions, duplication of the ice tests, substituting rock, suggested that K is not constant and that P = K x W x S, though valid for ice, does not necessarily hold for homogeneous limestone.&apos; Conclusions from this later work raised questions making continued investigation desirable because such conclusions do not destroy the practical value of the empirical equations or theory. Further study for the establishment of the relationship between load, burden and periphery of the pressure surface and possible application of these to the mechanism of rock blasting was undertaken by the authors of this paper. MECHANICAL TESTING - EXPERIMENTAL PROCEDURE Certain inconsistencies in the results of the aforementioned tests repeated on three types of limestone suggested these inconsistencies be attributed to rock inhomogeneity. It was also suspected that the loading speed, which could not be held uniform, may have contributed. The earlier work with both rock and ice

Jan 1, 1964

By S. K. Ruggieri, R. A. Jankowski

Airborne respirable dust levels on longwalls can be reduced if operators approach the dust control problem in a logical and fundamental manner. This can be accomplished through the proper application and continued use of effective dust control techniques. The Bureau of Mines is currently assessing the effectiveness of longwall dust control techniques in use today to provide mine operators with guidelines for selecting the most appropriate control technology. This paper presents a fundamental approach to the problem of shearer dust control. Three dust control techniques to be discussed are: deep cutting/increased pick penetration for reducing the amount of respirable dust generated; drum water sprays/improved water supply system to suppress the amount of airborne respirable dust; and improved external water spray system, the “shearer-clearer, "to push the dust close to the face. The techniques have been evaluated infield trials and have been shown to be both practical and effective in applications to control shearer generated dust.

Jan 1, 1985

Anticipating the increasing importance of establishing working conditions on a scientific basis, the Department of Labor created the Working Conditions Service. This service is distinct from that performed by the Mediation and Conciliation branch, which deals with working conditions and industrial relations as controversial issues between employers and employees. The work of the Service is conducted through three coordinated divisions; Division of Industrial Hygiene and Medicine, Division of Labor Administration, and Division of Safety Engineering. The Division of Industrial Hygiene and Medicine will develop standards of sanitation and medical practice in industries. The personnel of this Division is detailed from the United States Public Health Service. The Division of Labor Administration will advise employers as to employment systems and labor management policies, and assist in putting into operation standard policies.

Jan 2, 1919

By William Hurst

THE content of this paper is a presentation of the diffusivity theory for the calculation of the water drive on an oil reservoir in which b the history of reservoir pressure with time are the essential parameters for the determination of the rate and cumulative water encroachment into a field. The paper is divided into two parts-the main portion and appendix. The main body is essentially the application of the principles underlined here to actual field data. It consists of the work plots of the radial-flow case, and includes a discussion of an illustrated problem for which the water-drive calculations are treated in conjunction with the volumetric-balance equation. The appendix is a mathematical treatment of the linear, radial, and spherical cases of water influx into a reservoir.

Jan 1, 1942

By H. J. Levinstein, H. J. Guggenheim

RbFeF3 is a transparent ferromagnet with a large faraday rotation which permits the direct observation of magnetic domain structures in bulk crystals. If the position of dislocations within the crystal were known a study of domain wall dislocation interactions would be possible. In this paper an etch pitting solution is described which gives a one-one correspondent between the etch pits and the dislocations intersecting the (100) surfaces of RbFeF3 crystals. In addition, RbFeF3 is shown to have sufficient plasticity so that known arrays of dislocaticms can be put into the crystal. It is concluded that RbFeF, is an ideal material for the investigation of domain wall dislocation interactions. THE influence of lattice defects on the motion of domain walls in ferromagnetic materials has been studied extensively both theoretically and experimentally.4 The experimental data obtained has been qualitative in nature due to the lack either of a quantitative knowledge of the magnetic domain array in the material or of the nature of the dislocation configuration in the material. At room temperature RbFeFJ has the cubic perovskite structure. It is ferromagnetic below 86°K.5,6 It is also transparent and has a large faraday rotation in the magnetic state.7 The domain structure of this material is observable in three dimensions in crystals which are millimeters in thickness.&apos; Since RbFeF3 satisfies the requirements of having an easily visible three-dimensional magnetic domain structure, it was of interest to determine if the dislocation structure of the material could be determined and if the material was sufficiently plastic so that dislocations could be introduced into the as grown crystals. This is a report of the results of that investigation. EXPERIMENTAL PROCEDURE The crystals of RbFeFs used in this experiment were grown by a technique described elsewhere.5 In order to obtain flat strain-free surfaces, the samples were first cut to the crystal orientation desired and the surfaces were polished by employing standard metallographic techniques. The samples were then immersed in a solution of 1 to 3 g of KOH in 100 ml of water. This solution removes the damaged surface layers uniformly leaving a film on the surface of the sample. Etch pits are obtained by immersing the sample in an approximately 50-50 solution of 30 pct peroxide and concentrated acetic acid. The film formed during the KOH treatment turns deep red in color in the etching solution and flakes off the sample. The etching time required depends upon the pit size desired and

Jan 1, 1970

By S. G. Cupschalk, F. A. Dahlman, J. J. Wert

Studies have been undertaken to determine the indicidual effects of particle size, degree of long-range ovder, antiphase domain size, and root mean square stran on the microhardness and yield strength of ordered alloys. Dnta have been analyzed for Cu3Pt initzally ordered to a value of 0.82 and after deformations of 1 and 6 pct. It was observed that deformation fleatly reduced the degree of long-range order. Furtherrnore, wztkin this range of relatively small deforntntlons, the average particle size changed very little while the antiphase domain size was greatly reduced. Smultaneosly, the mcrohardness changed by a factor of two durzng the deforrtation process. PREVIOUS studies have reported some of the effects of cold work on the broadening of X-ray diffraction peaks. These investigations were performed on powder and wire samples representing both ordered and disordered states; i.e., the specimens were initially studied in a severly cold-worked condition. By comparing the difference in line shape between the annealed and cold-worked peaks, fundamental information was obtained concerning particle size, strain distribution in different crystallographic directions, degree of long-range order, and change in antiphase domain size. Considerable theoretical work has been done concerning the analysis of diffraction data obtained from cold-worked metals. Stokes&apos; expressed the change in diffraction profiles in terms of Fourier coefficients. Much of the work in this area has been summarized by warren2 in an extensive review article concerning the analysis of plastic deformation by X-ray diffraction. Cohen and Bever3 applied these techniques in studying the effects of cold work on alloy systems exhibiting long-range order. They utilized the Fourier coefficients of fundamental peaks in conjunction with those of the superlattice peaks to determine the change in antiphase domain size. Little work of this nature has been reported for ordered systems that have undergone small degrees of plastic deformation. The purpose of this investiga-tion was to determine the effects of small deformations in such a material with respect to particle size, strain distribution in various crystallographic directions, antiphase domain size, degree of long-range order, and hardness. EXPERIMENTAL PROCEDURE CusPt was used for the initial investigation since the order-disorder transformation takes place with- out a change in crystal structure. The transformation is readily detectable via X-ray diffraction techniques due to the large difference in the scattering factors of copper and platinum. Additionally, the alloy is relatively low melting (approximately 1300°C) and is easily deformable in both the ordered and disordered states. 1) Specimen Preparation and Cold Working. A 100-g, 12-in. diam., cylindrical specimen of Cu3Pt was prepared by melting and casting 99.99 pct pure Cu and Pt i.n vacuo. Prior to any mechanical working, the material was homogenized in a vacuum for 60 hr at 100O0C, and surface defects were removed by machining to a depth of approximately 116 of an in. The material was then cold-rolled, with an intermediate anneal, into a strip approximately 12 in. wide by 14 in. thick. Straightening and flattening removed another 0.025 in. from the thickness. After a recrystallization treatment at 750°C for 30 min, the specimen was slow-cooled from 55OoC, at the rate of 6°C per hr, down to 150°C to induce superlattice formation. This treatment yielded an ASTM grain size of 7 and a degree of long-range order equal to 0.83 0.06. After obtaining X-ray and Knoop hardness data, the sample was cold-rolled approximately 0.75 pct in one pass through a hand-operated jewelers&apos; mill. X-ray and hardness data were again obtained and the specimen was reduced an additional 5.41 pct in a single pass through the mill. 2) X-Ray Measurements. The specimen was examined in the ordered condition and after the two degrees of cold working previously mentioned using a General Electric XRD-5 unit equipped with a spectrometer and scintillation counter. Using Mo-Ka radiation with a zirconium filter, six orders of the 100 reflection were obtained. It was anticipated that point counting would be necessary for an accurate determination of the low-intensity peaks and tails: however, it was demonstrated that, by using a scanning speed of 0.2 deg per min and the appropriate time constant, the recorded data were sufficiently accurate. Thus, for ease of experimental procedure, all peaks were recorded on chart paper. Specimen position in the holder was considered to be insignificant after making a series of measurements of the same peak area in different positions with respect to the beam. Since peak overlapping did occur at high values of 20, it was necessary to separate the peaks graphically prior to analyzing the data in order to minimize this source of error. The peak tails were also carefully drawn to obtain the best possible data. Fourier coefficients of the line profiles were calculated on an IBM 7072 computer, and graphical meth-ods2j3 were employed in analyzing the results. For this type of calculation, in which the line profile is represented by intensities taken at set intervals, the intervals selected must be sufficiently small to give an accurate representation of the line profile. It was decided that for 20 = 0.02 deg the line profiles were

Jan 1, 1967

By Yap Chu-Phay

IN 1923, when the writer began his studies in metallurgy, he came upon an article by Professor Honda on the, Equilibrium Diagram of the Iron-carbon System, 1 which made a profound impression on him. What interested him most was this sentence: "In the recent diagram of the iron-carbon system, the solidus is usually shown as a curve bending considerably downward. But it can be shown by thermodynamics that if the liquidus is straight or slightly curved, the same must also be true for the solidus. Hence, in my constitutional diagram, the lower portion of the solidus is slightly bent upward." Ever since then the writer has been interested in thermodynamics, especially chemical thermodynamics. The applications of thermo-dynamics to the metallic systems have been, in the writer&apos;s opinion, sadly neglected, although we continually use the phase rule in our study of equilibria in the liquid and solid states of metallic alloys. Many investigators, among whom may be mentioned Heycock and Neville, and s Honda and his coworkers, have applied the simple Raoult-van&apos;t Hoff law of depression of freezing point, mainly to determine the heat of fusion, but no attempt has been made to investigate the applicability of the thermo-dynamic laws of solution (as opposed to the laws of solution derived from other sources) to metallic systems" showing either limited or complete solid solutions. Perhaps the reason for this neglect is that until recently there have been so few reliable data on the solidus, which is much more difficult to determine than the liquidus. The writer has under way at the present time an investigation of a number of systems, the solidi of which have been more or less reliably determined. Recently, the writer has not only shown the valid applicability of the thermodynamic laws of solution as applied to the system antimony-bismuth but has also suggested a method of attacking problems involving complete and incomplete equilibria.2 In the present paper, the same method of approach is employed. For convenience, we shall divide this paper into two parts:

Jan 1, 1931

By John J. Howard

WE are approaching the depletion of our principal source of iron ore-the Great Lakes deposits, which have provided 85% of the nation&apos;s requirements for the past fifty years. This situation presents a threat to our standard of living and our position as a world power. Fortunately, in the Great Lakes region there are still tremendous quantities of potential iron ore in the form of the low iron, high silica rock called taconite. The economical extraction of iron from taconite will insure our future steel supply if no new deposits available to the United States even in time of war are discovered. In the new process presented here, the iron is reduced directly by a simple method and then separated from the silica. The product is "feed," not to the blast furnace, but to the steel plant. This process requires very much less plant, less physical and chemical treatment, and less fuel and auxiliary materials than the conventional ore concentration-blast furnace method. In my opinion, this new, fundamentally different approach offers a better hope for the solution of the iron ore problem.

Jan 5, 1950