Search Documents

By Robert D. Pike

In November 1939, on behalf of the Harbison-Walker Refractories Co., the author undertook the study of the problem of utilizing the dolomite of northwestern Ohio for the manufacture of calcined magnesia suitable for use in refractories. Grateful acknowledgment is made of the unfailing assistance and encouragement throughout this work from the executive and technical staff of Harbison-Walker Refractories Company. The dolomite of the Niagara formation that is exposed or near the surface of a wide area in northwestern Ohio1 constitutes a vast supply of almost pure dolomite. It offers a virtually unlimited supply of cheap raw material of uniform dependable analysis for the manufacture of magnesia. A typical analysis of dolomite from the vicinity of Luckey, Ohio, follows: Stone Completely Calcined CaO(Sro)a............. 30.35 57.806 Mgo................... 21.55 41.050 SiO2. ................... 0.30 0.572 R2O3................... 0.30 0.572 Ignition loss............. 47.50 a SrO about 0.06 pct. Brines containing magnesium chloride or sea water can be reacted with calcined dolomite to produce magnesia.2'3 In such reactions the MgCl2 of the brine supplies some of the magnesia and the amount of dolomite required is thereby reduced by an equivalent amount, but brines of commercial importance containing magnesium chloride are some distance away from the purest grades of the dolomite of northwestern Ohio. It was decided therefore to concentrate upon the development of a suitable process for separating the lime and magnesia of dolomite, depending upon the dolomite itself as the sole source of magnesia. This would make it possible to place a plant at the dolomite quarry, thus eliminating the cost of transporting the stone and also rendering the calcined magnesia available at a most convenient production point, considering the cost of delivery throughout the steel industry. The selection of a process depending solely upon the dolomite as a source of magnesia also necessarily entails production of the lime content of the dolomite as a by-product. It was recognized that if such a lime by-product could be produced in a suitable form, a plant location in northwestern Ohio would also be advantageous for marketing the lime. The problem, therefore, was the discovery and development of a low-cost process for separating the magnesia and lime of the dolomite of northwestern Ohio and producing each in a form relatively free from the other, and meeting the respective requirements of established markets. A satisfactory solution of this problem has been found, and it is the

Jan 1, 1948

By R. M. Rose, K. A. Jones

Resistive measurements ulere made on superconducting niobium single crystals in transverse magnetic fields. Crystals were grouln in both high and ulfrahigh vacua, doped with stnall quantities of oxygen, and annealed in ultrahigh vacua at temperatures from 900' to 1350°C. Maxima in the fluxoid pinr~ir~g force were observedfor the [100] and [210] directions. The increase of the critical current density with dissoved oxygen was seen to saturate at relatively low concentration. This behavior, and the variation of J, and residual resistivity (as a function of oxygen content and annealing) of both clean and dirty gassy) crystals, is seen as a consequence of the formation of clusters with (210)~b habit planes and (200)ffo common boundaries. These suboxide clusters are apparenlly stable at high temperatures and very low oxygen concentrations. It is generally known that dissolved oxygen at concentrations well below the solubility limit sharply increases the critical current density of superconducting niobium.' Such a result would not be expected if Nb-0 solutions were random, not even as the result of segregation on the scale usually encountered in solid solutions. According to the Kim-Anderson theory of flux creep,' the critical transport current density is determined by the pinning force Fp associated with some feature of the microstructure. As the Lorentz force. a or (J X R), of the transport current in the magnetic field approaches Fp, flux creep and then flux flow occur. The pinning force is expected to be quite small if the heterogeneity involved is significantly smaller than tte range of coherency which for niobium is circa 250~.~ Although the strain field of an individual oxygen atom in the niobium lattice is relatively large, it does not seem plausible that individual atoms could be so effective as to account for the data. Also, ~ramer~ found that straining and strain aging specimens containing small amounts of oxygen on occasion decreased the residual resistivity. A possible explanation for the above behavior may be found in the work of van Ooijen and van der Goot,= who found that annealing changed J, for niobium foils containing oxygen, and they attributed the changes to ordering of the oxygen atoms. This phenomenon has been observed by other investigators using X-ray and PROCEDURE Cylindrical 4-in.-diam niobium single crystals with axial orientations [ill], [110], [112], and [oo~] were grown from pure niobium, see Table I for analysis, in an ion-pumped ultrahigh-vacuum system using the electron beam floating zone technique. Total pressure during growth was lo-'9 torr: the oxygen partial pressure was less than lo-" torr, as determined by a mass spectrometer. These crystals will be referred to as the "clean" crystals. Similar crystals were also grown in another system at a pressure of 5 X 10"6 torr. These crystals will be referred to as the "dirty" crystals. Specimens 14 in. long were cut from the as-grown crystals and one end was polished down to no. 600 carbide paper smoothness. A back-reflection Laue photograph was then taken in order to fix the crystallo-graphic directions transverse to the crystal. The critical current density J,, the current density necessary to produce a voltage drop of 1.0 pv between voltage leads placed a in. apart, was determined as a function of the magnitude and direction of the transverse magnetic field and of the oxygen concentration. The technique and experimental arrangement was essentially similar to that of Tedmon et al.' In the remainder of this paper, the azjmuthal angle $ for the field H is referenced to the [ I101 direction in all four crystals, and oxygen was added in small equal increments by anodization and annealing.7 The resistivity ratio, RR, of the resistance at room ternperature to that at 4.2"K (H =7.00 kG) was determined as well.

Jan 1, 1970

By O. L. Kowalke

THE measurement and control of temperatures have assumed positions of great importance in many industries. The manufacturers of byproduct coke and carbureted water gas find that proper temperature control helps to produce a better product and economizes in the use of raw materials. In the manufacture of glass, enameled ware, brass, and high-temperature refractories, temperature control is now regarded as being coordinate in importance with the control of materials used. To control such processes as malleablizing cast iron, and hardening, tempering, and annealing of steel in a manner to meet exacting market requirements has, within recent years, involved the installation of large and expensive pyrometer equipments. In many of these installations, it was necessary not merely to measure but also to record the temperatures over a period of time and thus obtain a record of the entire heat treatment and an effective check on the workmen in charge. In view of the importance of temperature measurement and control in such a wide variety of industries and the necessity for proper supervision of the installation and operation of the outfits, the following questions may be pertinent: What instruction is offered by the engineering colleges and what departments in the colleges are responsible therefor? The latest available catalogs of ten prominent engineering colleges east of the Mississippi River showed courses in high-temperature measurements given by the departments of physics. These courses, in general, were described as comprising classroom and laboratory instruction in the theory of high-temperature measurements, together with exercises in the calibration of the various devices used. In some cases it was stated that consideration would be given, in the courses, to the practical applications in the industries. In only one. college was the course required of all engineering students; in most colleges it was optional; in a few colleges, it was required only of certain groups. In colleges offering a course in metallurgical engineering, instruction in pyrometry was always given in connection with metallurgical laboratory work. The students in ceramic,

Jan 8, 1919

By Thomas Harris

This paper. was written in conjunction with the work being undertaken by the Technical Committees on Classification of Coal, and an effort has been made to compile information relative to the use of coal for stationary steam generation in order to use this information to assist the Committee on Classification of Coal for the ultimate purpose of elimination of losses both by the' reduction of indivi-dual effort and waste in the consumption of material. Under the auspices of the National Association of Purchasing Agents, a questionnaire was drawn up to develop this information from stationary steam plants throughout the United States. in order to consolidate the information de-veloped from the many hundreds of boiler tests on coals consumed by various coal¬burning equipment. These questionnaires covered: 1. The company reporting, location and method of delivery to the plant. 2. Complete coal date, including description of coals used (with. sufficient space to- include first, second and third, preference) on--source of coal used,- complete-analysis and factors affecting choice of, coal used. 3. Plant data, divided into - A. Hand fired, B. Overfeed stokers,. . C. Underfeed stokers, D. Traveling grate stokers, E. Pulverized coal, and included complete description of furnace data, draft data, coal-burning rate, type of stoker, type of pulverizer, efficiency date and remarks.

Jan 1, 1933

By L. A. Willey

IN 1953, a method for filtering a liquid phase from solid phases while in equilibrium at elevated temperatures was devised at the Alcoa Aluminum Research Laboratories. Since then, it has been applied to the investigation of liquid-solid equilibrium in metallic systems. In application, the method simplifies the centrifuge filt.ration procedure as developed by Scheil and described by Gebhardt Fig. 1 shows a sketch of the filtering apparatus located within a thermal analysis furnace. It consists of a stainless steel filter crucible A, into the bottom of which a porous carbon filter disk B, 1 3/4 in. diam by 1/4 in. thick, is sealed to the shoulder and rim with carbonaceous cement. The base of the filter crucible, machined to an angle, fits into a tapered seat at the mouth of a stainless steel vacuum chamber C. A connecting tube from the vacuum chamber to a vacuum line also serves as a means for supporting the apparatus from the base of the furnace. An alundum crucible D of 25 ml capacity is placed with- in the vacuum chamber below the filter for collecting the filtrate. Two thermocouples E, in stainless steel protection tubes, which extend from 1/16 to in. above the center of the filter, are mounted on the rim of the filter crucible. One thermocouple is used in differential connection with the furnace control thermocouple to regulate rates of heating and cooling. The other serves as a means for recording the temperature of the alloy prior to filtering. A suitable mold coating is used on exposed surfaces of stainless steel parts to guard against attack upon these parts as well as to avoid contamination of the alloy samples. A mold wash prepared from precipitated CaCO, is suitable for aluminum alloys. The porous carbon for the filter disks and the carbonaceous cement, grade 200 (graphite base), were obtained from the National Carbon Co. Porous car-bon, grade Nos. 10 to 60, has been employed. Grade No. 40, however, appeared to give the optimum advantages in operation. In operation, an alloy sample is remelted and heated to about 50°C above its liquidus temperature. At the same time, the filter apparatus is preheated to about the same temperature. The alloy then is cast into the filter crucible.

Jan 1, 1957

ALTHOUGH the refining period of the heat is generally defined as starting after the charge has been completely melted, it may more properly be considered as beginning with the first efforts to facilitate the shaping up of the slag and the making of corrective additions for the control of slag or metal composition. Such actions may be initiated during the latter half of the lime boil. The early part of the refining period may, then, in essence overlap the latter part of the melting period. The primary aims of the refining period are: (1) to reduce phosphorus and sulfur from the steel bath to levels safely below the maximum contents specified; (2) to eliminate carbon to a specified level as rapidly as possible and still allow time for proper conditioning of the slag and attainment of the necessary bath temperature; and (3) to have the heat ready for tapping or furnace deoxidation, with slag in the proper physical and chemical condition, and with carbon and oxygen contents and the temperature of the steel at the proper levels for the composition and grade of steel being produced. The particular conditions that fulfill these aims are distinctly different, depending upon whether the steel is to be finished according to fully killed. semikilled, or rimming practice and also depending upon the carbon range specified. Regardless of the type of charging practice employed, the object of the refining period is to produce repeatedly the desired finishing and tapping conditions for the grade of steel being produced. The variations and proportions of raw materials used in the charge may cause some variations in the degree of control required during refining, but not in the method of control. The refining period can therefore be discussed from a viewpoint largely independent of charging and melting practice. SHAPING UP THE SLAG In the first helper's vocabulary, refining practice consists in

Jan 1, 1951

By Gordon E. Agar

Several correlations have been proposed to relate energy consumption and size reduction in comminution, and although these are arrived at from different starting points, it is postulated that they are all statements of the same basic concept. To test this postulate, the dry ball mill grindability of langbeinite was determined, and the results were analyzed according to the various methods. An examination ' of the energy-particle size relationships proposed in the recent past revealed that they had much in common. In fact, the conclusion was tentatively drawn that these expressions were essentially the same, even though they were arrived at from quite different basic premises. The equations attributed to Charles2 and Holmes3 were shown to re- duce to the same single equation, W - A K-3, and the simulated continuous test used by Maxson et al.4 was shown to give the best experimental value of the required empirical parameter, ß. Furthermore, the size distribution parameter a in the Schuhmann equation, y - (x/K)2, was shown to be equal to ß in many cases. The kinetic approach used by Arbiter and Bhrany5 should give the same results as the Maxson test procedure; however, the batch operation used by Arbiter and Bhrany could not produce data that would be as precise as the simulated continuous technique. To test the validity of these conclusions, the simulated continuous method was used to obtain data on the dry grinding of langbeinite. The results are discussed in terms of the various equations and approaches. APPARATUS AND MATERIAL A ball mill with internal dimensions of 17.5 cm (6 7/8 in.) in length by 19.4 cm (7 5/8 in.) in diam was loaded to 50% of its volume with balls 3.2 cm in

Jan 1, 1969

SLAG composition, slag constitution, reactions in slag, and reactions between slag and metal-in other words, the physical chemistry of slags-are matters of great importance to the open-hearth operator, whether or not he makes use of any detailed knowledge of them. Although this is a relatively young branch of the science of steel- making, much progress has been made; however, much remains to be learned, and many of the statements that can be made at present are probably--or even certainly-subject to future change. Nevertheless, the physical chemistry of slags is sufficiently developed to provide a reasonably secure basis for real understanding of steelmaking reactions. FUNDAMENTALS OF SLAG CONTROL By way of introduction, some time is spent in this chapter on effecting an easy transition from some of the more "practical" manifestations of slag to discussions couched in the more formal language of physical chemistry. This necessitates a certain amount of repetition, but it is felt that the purpose of the chapter is best served in this way. Reactions in the metal phase have products that find their way into the slag and are important components thereof; they are discussed in detail in the preceding chapter. Some substances distribute themselves Between slag and metal in definite fashion, and others are found only in the slag. Their reactions are a large reason for this chapter. Limitations of Slag Control. The open-hearth process is essentially oxidizing and cannot be otherwise operated. (Oxygen gradients in the furnace, the mechanism of oxygen inflow, and similar subjects are discussed in Chapter XIX.) As shown in the calculations of material and heat balances for the charge (see Chapter XV), from 25 to 50 lb. of oxygen will flow from air or combustion gases into the charge or molten bath during the heat for each ton of liquid steel

Jan 1, 1944

By Thomas Brownfield

Development and production activity in Oklahoma during the year 1940 was of routine nature. Production, according to the Corporation Commission's figures, averaged 409,100 bbl. daily as compared with 421,000 bbl. for the year 1939. Discoveries were of minor importance except for the Cumberland pool in Marshall and Bryan Counties, in the southern part of the state. Maintenance of a relatively stable producing rate is attributable to the drilling of new wells and the recompletion of many old wells in the previously established producing areas. During the year 1785 new wells were drilled, a decline of approximately 10 per cent as compared with the previous year. Of the wells drilled, 962 were oil wells with a combined initial production of 241,000 bbl. daily, 172 were gas wells having aggregate capacities of 1205 million cu. ft., and 651 were dry holes. Wildcat activity increased 20 per cent over 1939 and 227 such wells were completed during the year; that isl 43 oil wells, 16 gas wells, and 168 dry holes. In addition to the new work completed, 603 wells were recorded as having been drilled deeper or plugged back to test new horizons; included were 334 producing wells with total initial production of 65,000 bbl. daily, 37 gas wells with initial aggregating 305 million cu. ft., and 232 abandonments. Footage drilled amounted to 4,730,000 ft., an average of 2650 ft. per well as com-pared with an average depth of 2600 ft. recorded the previous year. The principal new pools discovered as a result of the exploratory drilling were Cumberland; East Cromwell, in Okfuskee County, and Prague, in Lincoln County. At the end of the year Cumberland had 13 completed wells, which averaged 700 bbl. initial through tubing from the Simpson Bromide formation (Ordovician) at 4750 ft. East Cromwell had 10 wells with average initial of 435 bbl. in the Cromwell sand (Pennsylvanian) at 3460 ft. Prague had II wells with an initial average of 220 bbl. from the Senora sand (Pennsylvanian) at 3260 ft. There were notable extensions to the Dill pool, Okfuskee County, and to the Hewitt pool, Carter County. At the end of the year, 19 producing wells had been drilled in the former, with initials averaging 1000 bbl., and 63 wells averaging 150 bbl. daily in the latter. There were no notable changes in the policy of State conservation authorities with respect to proration. The Bureau of Mines recommendations for the year averaged 413,000 bbl. daily; the State author-ities fixed allowables at an average of 406,000 bbl. daily, while, as noted above, production averaged 409,100 barrels. The most important development in the older areas occurred in the following pools: Billings.—Seven oil wells with an average initial production of 2500 bbl. and two dry holes were completed during the year. Production from the Simpson horizon averaged 6025 bbl. daily as compared with 5950 the previous year. Production from this field has been almost steady since reaching its peak early in 1937. The major portion of the pool is efficiently operated as

Jan 1, 1941

By Thomas Brownfield

Development and production activity in Oklahoma during the year 1940 was of routine nature. Production, according to the Corporation Commission's figures, averaged 409,100 bbl. daily as compared with 421,000 bbl. for the year 1939. Discoveries were of minor importance except for the Cumberland pool in Marshall and Bryan Counties, in the southern part of the state. Maintenance of a relatively stable producing rate is attributable to the drilling of new wells and the recompletion of many old wells in the previously established producing areas. During the year 1785 new wells were drilled, a decline of approximately 10 per cent as compared with the previous year. Of the wells drilled, 962 were oil wells with a combined initial production of 241,000 bbl. daily, 172 were gas wells having aggregate capacities of 1205 million cu. ft., and 651 were dry holes. Wildcat activity increased 20 per cent over 1939 and 227 such wells were completed during the year; that isl 43 oil wells, 16 gas wells, and 168 dry holes. In addition to the new work completed, 603 wells were recorded as having been drilled deeper or plugged back to test new horizons; included were 334 producing wells with total initial production of 65,000 bbl. daily, 37 gas wells with initial aggregating 305 million cu. ft., and 232 abandonments. Footage drilled amounted to 4,730,000 ft., an average of 2650 ft. per well as com-pared with an average depth of 2600 ft. recorded the previous year. The principal new pools discovered as a result of the exploratory drilling were Cumberland; East Cromwell, in Okfuskee County, and Prague, in Lincoln County. At the end of the year Cumberland had 13 completed wells, which averaged 700 bbl. initial through tubing from the Simpson Bromide formation (Ordovician) at 4750 ft. East Cromwell had 10 wells with average initial of 435 bbl. in the Cromwell sand (Pennsylvanian) at 3460 ft. Prague had II wells with an initial average of 220 bbl. from the Senora sand (Pennsylvanian) at 3260 ft. There were notable extensions to the Dill pool, Okfuskee County, and to the Hewitt pool, Carter County. At the end of the year, 19 producing wells had been drilled in the former, with initials averaging 1000 bbl., and 63 wells averaging 150 bbl. daily in the latter. There were no notable changes in the policy of State conservation authorities with respect to proration. The Bureau of Mines recommendations for the year averaged 413,000 bbl. daily; the State author-ities fixed allowables at an average of 406,000 bbl. daily, while, as noted above, production averaged 409,100 barrels. The most important development in the older areas occurred in the following pools: Billings.—Seven oil wells with an average initial production of 2500 bbl. and two dry holes were completed during the year. Production from the Simpson horizon averaged 6025 bbl. daily as compared with 5950 the previous year. Production from this field has been almost steady since reaching its peak early in 1937. The major portion of the pool is efficiently operated as

Jan 1, 1941

By Freeman Bishop

Quietly picking his way through the thorny thicket of conservation issues is William E. Ruckelshaus, director of the Environmental Protection Agency in which President Nixon gathered the various anti- pollution units from the Interior, Commerce. Agriculture and Health. Education and Welfare departments. Mr. Ruckelshaus. EPA's first administrator, moved over from being Assistant Attorney General in charge of the civil division at Justice to this new post. Essentially, EPA is charged with administering swiftly proliferating antipollution programs. This means policing industry cities, farms and everything else. Ruckelshaus has been quietly fitting together the various pieces of this new agency, pulling then1 out of other Federal departments. Some 5800 employees are involved. The budget in 1971 for these segments will total about $1.5 billion.

Jan 1, 1971

By Walter H. Bruckner, George B. Clark

SINCE the end of World War II interest has been increasing in the use of shaped charges in the mining industry and in other industries using explosives for blasting purposes. Shaped charges employ the principle known as the "Munroe effect," which was discovered by Charles E. Munroe more than 50 years ago (in 1888). Details of their design have been explained e1sewhere.l,2,3 Fig I shows the essential features of design of two types of shaped charges (with conical and hemispherical cavities) and a schematic sketch of their action upon detonation. The following discussion deals with the behavior of the metal in the cavity liners when they are subjected to intense pressures exerted when the explosive charge is detonated. Among the conclusions reached in research on shaped explosive charges, the following have been established concerning cavity liners: 1,2 I. The optimum wall thickness of a conical cavity liner is dependent upon the apex angle of the cone as well as on the base diameter of the charge. Acute apex angles require thinner walls for optimum performance and more obtuse angles require thicker walls for the same base diameter. 2. Cones were more effective in forming a penetrating jet when the walls were tapered; i.e., the thickness of the wall of the cone increased from the apex down. 3. The physical and mechanical proper- ties of metals have a marked effect upon their performance as cavity-liner material. Boiling point, ductility, malleability, tensile strength, and hardness are among the properties that influence the effectiveness of a metal used as a cavity liner. Lead, for example, makes a wide, flat crater in steel plates. Aluminum makes a deeper crater than lead, and an aluminum alloy having a high tensile strength makes a deeper hole, but slightly smaller in diameter. Cast iron makes a deep, narrow hole. These findings, together with the following analysis under Metallographic Survey of Slug, offer solutions to many of the problems involved in solving the mechanism of the formation of Munroe jets. It has been fairly well established that cavity liners collapse in a manner similar to that indicated in Fig 2. Conical liners are known to collapse upon themselves while hemispherical liners are believed to turn inside out in the process of jet formation. The first has been definitely proved by recovery of collapsed portions of cones, while liners from partly detonated charges show that hemispheres may turn inside out. Fig 3 shows a sketch of a recovered slug from a 6-in. shaped charge using a 45° cone made of cast iron. (This size of charge drilled holes up to 3 ft in depth in solid granodiorite.)

Jan 1, 1947

By Milton H. Fies

Although pig iron from iron ore and red cedar charcoal preceded the mining of coal by many years, for tradition says that Alabama iron was used to shoe the horses of Andrew Jackson's soldiers, coal was not produced until 1830. In that year, coal was mined in Tuscaloosa County, in the vicinity of what is now the University of Alabama, and shipped on flat boats (obviously during the wet season, for there were many shoals) down the Warrior River to Mobile. About that time, the first railroad, the Decatur & Tecumseh, was being constructed in northern Alabama to overcome the obstructions to freight traffic caused by the now well-known Muscle Shoals in the Tennessee River. This railroad was patterned after a railroad at Mauch Chunk, Pa., which was used for hauling anthracite from the Panther Creek valley. The Alabama railroad, which required about four years to complete, was 46 miles long and was used solely for the transportation of cotton. Although it was a failure, it demonstrated the practicability of the undertaking, and the succeeding railroads, which were begun in 1834, 1848, 1852, and 1853, added immeasurably to the development of the coal resources of the state. Between the years 1830 and 1860, practically all the coal mined in the state was dug from the outcrop near the river or from the river beds, and shipped by boat to Mobile. Transporting coal down the Warrior River was an undertaking of great risk, required much skill, and frequently had heavy losses. It is recorded that this coal was sold to the gas company in Mobile in 1844; it was most likely mined from the Black Creek Seam. In 1914, on the completion of Lock 17, the Warrior River became a navigable stream from 9 miles above Cordova, Ala., to Mobile and offers a great opportunity for the future development of the coal resources of the state. Coke for foundry use was first made in Alabama in 1855. It was 21 years later, however, in 1876, that pig iron was made from Alabama ore with Alabama coal.

Jan 1, 1925

By J. R. Linney

Demand for eastern magnetite in 1948 necessitated practically all eastern magnetite industries to operate on a six-day week, with the result that over 11,000,000 long tons of crude ore were mined, and the shipping products amounted to approximately 5,000,. 000 long tons. Reports indicate that operating on a six-day week and doing maintenance work on the seventh day was satisfactory and resulted in excellent continuity of operation. In the Port Henry district, Republic Steel Corp. once again set new all-time records for the production of crude ore and total shipping product; 1,868,000 long tons of crude ore were mined, 945,000 from the Old Bed mine, 408,500 from the Harmony mine, and 514,500 from the Fisher Hill mine. Of the 969,000 long tons of shipping products, 663,800 long tons were sinter, 181,000 lump ore, and 115,200 con¬centrates.

Jan 1, 1949

By Walter R. Hibbard

THE increased strength of a polycrystal-line metallic aggregate compared with that of its individual crystals generally has been associated with complex stress distributions at the grain boundaries resulting from atomic irregularity between grains. This disregistry, together with the necessity for adjacent crystals to deform 'compatibly regardless of the single crystal crystallographic strain mechanism, complicates this mechanism so as to increase the metal's resistance to deformation. Although Taylor1 has shown from purely mechanical considerations the requirement for at least five active slip systems to absorb the complexities during the homogeneous deformation of polycrystalline face-centered cubic metals, experimental studies by Barrett and Levenson2 indicate that this is feasible only in a qualitative sense because of deviations from homogeneous deformation. Seitz and Read in their review3 state: "Unfortunately . . . present knowledge of the grain boundary influence is not sufficient to complement the work in single crystals and provide us with a good foundation for treating polycrystals." The purpose of this investigation was to attempt to clarify the gap between single crystals and crystalline aggregates by an analysis of the effects of deformational stresses. Some of the results were described by C. H. Mathewson in his 1943 Campbell Memorial Lecture.21 PREVIOUS INVESTIGATIONS Since the performance of single crystals deformed under pure stresses has been relatively thoroughly investigated, the most significant researches are concerned primarily with deviations from single crystal behavior of large grained specimens. Qualitative grain boundary effects involving the observed amount of slip were reported by Carpenter and Elam5 in 1921. Individual crystals in a two or three grained aluminum specimen deformed by tension acted in the normal manner described by Taylor and Elam4 except for marked modifications at the grain boundaries. There the power to withstand deformation was considerably increased, leaving a ridge on the specimen where decreased slip occurred, often noticeable 34 in: from the boundary. Adcock,6 Yamaguchi,7 Seumel,8 Hirst9 and others have also reported this phenomenon as a qualitative trend. Yet attempts by O'Neill10 and Ljunggren11 to measure a difference in hardness at grain boundaries in undeformed specimens were unsuccessful. Miller12 measured quantitatively the reduction in slip near the boundary between the single crystal and polycrystalline areas of zinc specimens. These effects consisted of two parts: I. Next to the polycrystalline interface the distribution of stresses was so altered

Jan 1, 1948

By W. Rostoker, A. S. Yamamoto, K. Anderko

ALTHOUGH the corrosion resistance of magnesium and its alloys is closely related to iron content, there has been no direct measurement of the solid solubility of iron in magnesium. Bulian and Fahrenhors;1 and Mitchel]2 agree that pure iron or a limited terminal solid solution crystallizes from the Mg-rich liquid. For this reason a magnetic-moment method was selected to estimate that portion of the total iron content which is not in solid solution. Since iron in solid solution in magnesium cannot contribute to ferromagnetism, the difference between chemical and magnetic-iron analyses should yield the solid solubility. By experimentation it was found that the melting of pure sublimed magnesium (99.995 wt pet purity) in Armco-iron crucibles at about 800°C is a convenient way to introduce small amounts of iron. Melts retained 5, 10 and 20 min at 800°C analyzed 0.003,, 0.005,, and 0.018 & 0.001 weight pet Fe, respectively, after being stirred, heated to 850°C, and cast into graphite molds. The as-cast alloys were pickled in acid (dilute HC1 + HNO3), annealed at 600°C for 3 days, scalped on a lathe to remove the pitted surface, pickled again, extruded at about 100°C to 3-mm wire, reannealed 41/2 days at 500°C, and water-quenched. The specimens were again scalped, pickled, and used both for chemical and for magnetic analysis. Most of the precautions described were intended to prevent iron pickup by contact with tools or superficial iron enrichment by volatilization of magnesium during heat-treatment. It is believed that the specimens ultimately used for test were homogeneous and characteristic of phase equilibria at 500°C. Magnetic Analyses A susceptibility apparatus of the Curie type was used for magnetic analyses. Field strengths of up to 10,400 oersteds could be generated. By this method, an analytical balance measures the force of attraction which a calibrated magnetic field exerts on a suspended specimen. The force equation is as follows f/m = M dh/dy where f/m = force per unit mass of sample M = magnetic moment per unit mass dH/dy = magnetic field gradient The dH/dy characteristic of the instrument is determined by the use of a standard palladium sample, and the calibration is made independently for all values of H. Since a large finite field is required to saturate an assembly of ferromagnets, it is necessary to measure the apparent magnetic moment for increasing steps of H until a saturation value is obtained. The percentage of iron in the sample as free ferromagnetic iron may then be computed simply C= 100 (M1/M1) where C = percent content of undissolved iron in sample M1 = saturation magnetic moment of sample per unit mass M1 = saturation magnetic moment of iron per unit mass taken as 217 emu-cm per gm There is no serious difficulty in applying this method except for the unusual magnetic behavior of very fine particles of ferromagnetic substances. It has been found and is the basis for a widely accepted theory that with sufficient subdivision, the magnetic fields required to saturate and the coercive force after saturation rise to exceedingly high values. Recent work on precipitates of Fe and Co from copper solid solutions8 showed that about 5000 oersteds were necessary to approach saturation. The magnetic moments as a function of field strength measured in the present investigation are listed in Table I. Only the 0.018 wt pet Fe alloy yielded a magnetization curve with a fairly well-defined saturation plateau at 3.76x10 -2 emu-cm/ gm. This corresponds to 0.017 & 0.001 wt pet Fe in the alloy. This indicates that the solid solubility must be of the order of 0.001 wt pet Fe. The magnetic-moment data of the other two alloys are badly scattered, indicating that the amount of ferromagnetic iron in these samples is so low that the magnetic forces acting on them cannot be measured accurately by the analytical balance used. Nevertheless, the fact that even the 0.003, wt pet Fe alloy shows ferromagnetism indicates that the solid solubility must be below that value. Acknowledgment This work was sponsored by the Pitman-Dunn Laboratory of Frankford Arsenal, Philadelphia, Pa. The support and permission to publish are gratefully acknowledged. References W. Bulian and E. Fahrenhorst: Zeic. Metallkunde, 1942, vol. 34, pp. 116-170. 2 D. W. Mitchell: AIME Transactions, 1948, vol. 175, pp. 570-578. 3 G. Bate, D. Schofield, and W. Sucksmith: Philosophical Magnsine, 1955, vol. 46, pp. 621-631.

Jan 1, 1959

By E. J. Ripling

TUBES may be produced by a large number of forming processes, the most common of which will be discussed analytically in this paper. In no case will the stress analysis for any given tube producing process be derived formally for where such analyses are available, they may be referred to readily. Rather, emphasis will be placed on the interpretation of the theory of the different processes, few of which are developed to a state that will allow rigorous mathematical analyses, in an attempt to give a rational description of the effects of the different variables involved in each method. Tube producing methods can be divided into two groups: Those used to form shells, and those used to further work these shells into a shape more suitable for their final use. Among the first group are included roll piercing, extrusion and cupping for seamless shells, and bending with welding for welded tubes. The re-forming processes include sinking, drawing with a plug, and drawing with a rod. Only the plastic forming operations will be discussed here; other forming processes such as casting shells will not be considered. PRODUCTION OF SHELLS Shells for Seamless Tubing Piercing: The extremely important process of forming an axial hole in a billet by oblique rolling never has been analyzed satisfactorily, although a certain amount of experimental work relating to this process has been conducted. There are a number of factors that make piercing difficult to analyze; one of these is the fact that piercing is not a problem in plasticity, but one in fracturing, and the laws of fracturing are even less well understood than those of plasticity. If, however, it is assumed that fracturing occurs on a surface as a result of tensile stresses acting normal to this surface, piercing can be analyzed qualitatively by examining the stresses established in the oblique rolling process. To determine the origin of the tensile stresses that are thought to effect piercing, it will be necessary to know the angular relationships between the maximum stresses that are established in piercing. These angles quite frequently can be determined in a plastic deformation process by an examination of the deformed product. For example, consider the stresses established when a tensile test is conducted on a rectangular cross-sectional specimen of pearlitic steel. When stretched, this material first flows plastically, exhibiting the well-known yield jog on a stress-strain curve. The formation of the slip areas that give rise to the yield jog can be detected during the straining, since these flowed areas cause depressions on the specimen surfaces which can be seen if the surfaces are polished highly. The plastically strained areas also can be found after the specimen has been stretched to a strain not exceeding the yield jog, by sectioning the test piece and. etching these sections with Fry's etch. With this etchant, it is possible to dis-

Jan 1, 1951

By A. B. Young

THERE were produced in this country in 1923 probably in the neighborhood of 12,000 or 13,000 tons of refined and crude arsenic, by far the greater portion coming as a by product of smelting operations. Early this year copper smelters were producing arsenic at the rate of about 425 tons per month and lead smelters at the rate of 7;0 tons per month. During the entire eighteen years prior to 1919, there were produced in the United States only 47,000 tons of arsenic, which amounts to only 25 per cent. of the present output. The great increased demand has come about through the augmented use of arsenates as insecticides and arsenates as weed killers. In an extract from "Mineral Resources of the United States" on "Arsenic in 1922," Messrs. Heikes and Loughlin say, "The minimum possible demand for arsenic in 1923 was estimated at the end of 1922 to be about 13,000 tons, including 2000 tons for plate glass manufacturers, 3000 tons for lead arsenate, 3500 tons for calcium arsenate, 1500 tons for weed killers, 1200 tons for Paris green, 1000 tons for sheep dips and 750 tons for proprietary mixtures. More recent information, however, indicates twice as great a demand for calcium arsenate." The latter has found great use in the last three or four years as a weapon to combat the boll weevil pest of the southern cotton belt. ~t the present writing refined white arsenic is being quoted on the New York market at from 13)d c. to 1455 c. per Ib., while the average price during the eighteen-year period just mentioned was 4.8 c.

Jan 1, 1924

By Ernest R. Lilley

While American scientific literature contains much information upon geologic conditions controlling the production of oil in Rumania, copper in Chile, and other fuel and metallic resources in many foreign countries, it is singularly lacking in data about the nonmetallics outside of the United States. Thus, though the United States is the outstanding market for European high-quality refined kaolin, and for the chinaware, porcelain, and other products of the European ceramics industries, American literature contains only the briefest references to the deposits from which the raw kaolin utilized is obtained. To the writer, to whom has come in the past year the opportunity of visiting a number of these deposits personally, they have proved of extreme interest both commercially and geologically. It is the latter phase that is discussed in this paper. The older and now largely crystalline rock areas of France, Germany, and other parts of western Europe contain numerous pegmatite dikes of which the upper portions have been subjected to surface weathering and kaolinization in much the same way as those of the eastern portion of the United States. Like the latter, the European pegmatite kaolins have long been known for their freedom from iron and other impurities offensive to the china and porcelain manufacturer. Unfortunately, they are also, like the American deposits, individually of small size and noted for their high costs of production. Deposits of sedimentary clay similar in many respects to the high-quality sedimentary kaolins of Georgia and South Carolina are known and worked, notably in southern Germany and in the Newton Abbott district of Devon and Dorset in England. In general, their relationship to the parent rock from which they were derived is more evident than in the United States and the individual deposits are of smaller areal extent and less regular in outline. While these deposits are of considerable economic importance they did not, because of their similarity to deposits in America, attract and hold the interest of the writer to the extent that several other types of deposits did. It is to the latter, which are so different from the kaolin

Jan 1, 1932

By Robert M. Grogan, Gill Montgomery

Fluorspar, the commercial name for fluorite, is a mineral composed of calcium fluoride, CaF,. Its valuable properties are due to its content of fluorine, and it is the principal commercial source of that element. The name is derived from the Latin word "fluere," to flow, because the mineral has a low melting point and is used in metallurgy as a flux. Cryolite is a sodium aluminum fluoride, Na,AlF,. It is a rare mineral which has been found in commercial quantities in only one place in the world, Greenland. Small amounts of it are shipped from stock in that country, and its place in industry has been taken over almost completely by synthetic cryolite. Because of the relative unimportance of cryolite, discussion of it has been relegated to a short section at the end of this chapter, which is principally concerned with fluorspar. History Fluorspar was used for ornamental purposes by the Greeks and Romans, who fashioned such things as vases, drinking cups, and table tops from it. Various peoples including the Chinese and the American Indians carved ornaments and figurines from large crystals. Its usefulness as a flux was known to Agricola (1564), who wrote about it in 1546. Mining began in England about 1775 and at various places in the United States during the period 1820 to 1840. Production became substantial following the development and widespread adoption of the basic open hearth method of making steel, in which fluorspar is used as a flux. After that, production and usage were stimulated by growth in the steel, aluminum, chemical, and ceramic industries and were accelerated by World Wars I and II. Fluorocarbons entered the picture in 193 1 and the use of anhydrous hydrogen fluoride (HF) as a catalyst in the manufacture of alkylate for high octane fuel blends began in 1942. The development of the froth flotation process in the late 1920s, a differential flotation scheme for separating fluorspar from galena, sphalerite, and common gangue minerals in the 1930s, and the application of heavy-media concentrating methods to the treatment of low grade ores in the 1940s were outstanding technological contributions that enabled increased production of fluorspar concentrates. In recent years the development of pelletizing and briquetting processes for making flotation concentrates into gravel-size particles for use in steel furnaces and the development of more efficient and selective flotation schemes for treating crude ores containing abundant dolomite and barite have been major improvements in the industry.

Jan 1, 1975