Search Documents

By Robert F. Mehl

THE mechanical behavior of metals and alloys is presumably conditioned by two factors; namely, the crystalline symmetry and the interatomic forces. Considerable attention has been given to the first of these factors through the recent advances in X-ray technique. It is the purpose of the present paper to call attention to the importance of the second of these factors, to point out promising methods of investigation, and to present some pertinent data. Plastic deformation takes place by slip along atomic planes.1 This slip may be inhibited in a number of ways: by the interatomic forces of cohesion which bind the atoms rigidly in a lattice structure, which in pure metals is usually of high symmetry; by lattice distortion caused by solid solution formation or by mechanical strain; by the intercrystalline boundaries where slip is restrained, probably by the non-registration of the atom planes in adjacent crystallites;2 and by the presence of small hard particles which serve to "key" the slip along the atom planes.3 In pure metals, and perhaps also in solid solutions, the atom planes of easiest slip are those exhibiting the greatest density of atomic population and the greatest interplanar distance4 and apparently can now be predicted from the analysis of the lattices. Concerning the interatomic forces, which resist this slip by holding the atoms firmly together, little is known. Most textbooks on physical metallurgy, following the work of Bottone,5 correlate the hardness of the pure metals with the atomic volume,

Jan 1, 1928

By Robert G. Johnson, Richard J. Prosen

THE present work was done in connection with a program for investigating metal-to-ceramic braze techniques using the well-known reactivity of titanium with certain ceramic oxides. The investigation extended over the range of 0 to 30 pct Ti. The indium was obtained from the Indium Corp. of America and was specified to be 99.97 pct pure. The titanium was supplied by Metals Disintegrating Co. and was stated to be 99.5 pct pure. Each 2 to 4 g quantity of the alloy compositions studied was prepared using a mixture of 300 mesh powders pressed into pellet form. The pellets were heated in thin-walled molybdenum crucibles using a resistance-wound furnace in a vacuum less than 10-4 mm of Hg. Little reaction occurred between the molten alloy and the crucibles at the temperatures and short time intervals used. Only slight spectroscopic traces of molybdenum were found in the melt after a typical period of heating. The points shown on the phase diagram of Fig. 1 represent thermal arrest measurements. The phase boundaries shown are consistent with the thermal arrest and X-ray data obtained. The temperatures were determined using a Pt-Pt 10 pct Rh thermocouple with the junction spot-welded to a short molybdenum rod. The rod was almost completely immersed in the liquid metal, so that good thermal contact with the melt was achieved. The small mass of the crucible and its contents made it possible to obtain many heating and cooling curves in a few minutes time, an advantage which helped to minimize the effects of indium evaporation at the higher temperatures. A Brown strip chart recorder was used to display the thermal arrest curves. To check the technique, the melting point of 99.999 pure Al was measured and found to be within 1 of 660.2c, the accepted melting point. The upper limit of temperature with this technique was about 900°C beyond which the evaporation rate of indium became great enough to alter appreciably the alloy composition during the runs. A peritectic transition was found at 796°+ 5°C from 1.5 to 30 wt pct Ti. It was not found at 0.5 or 1.0 pct. A small super-cooling effect was observed. The melting-point transition to the B + L phase was found up to 20 pct Ti but not at 25 pct. Within the 1 deg accuracy of the measurement, the transition temperature was that of pure indium, 156°C. The liquidus line to the left of the 1.5 titanium point was located only approximately. The two crossed circle points at 1.0 and 0.5 pct Ti place a lower limit on the liquidus line and were determined by observing visually the cessation of vibrations in the melt caused by the damping effect as B-phase crystals were formed during cooling. The B-phase boundary was found at 23.8 pct Ti by X-ray analyses of small single crystals of the B phase isolated from 2 pct Ti melts. The compound was found to be Jetragonal with lattice dimensions of c = 3.052A and a = 10.094W. From the unit cell dimensions and the measured density of 6.42 i 0.05 g per cc, the compound was determined to be In4Ti3 which has 23.8 pct Ti. The calculated density of 6.44 g per cc is obtained assuming 2 mol

Jan 1, 1962

C. A. ROSE, New York, N. Y. (written discussion *).-Without doubt the excellent results obtained at Ajo will cause surprise among metallurgists; 75 per cent. average capacity and 80 per cent. extraction during the first year of operation of a plant using a new metallurgical process are figures that speak for themselves. It is obvious that the most troublesome feature of the process is the fouling of solutions. The effects of this are most evident in the electrolytic tank house; but apparently the solutions are so heavily loaded with salts that their dissolving power is also impaired. This is indicated by the fact that copper comes into solution during washing after the leaching of the ore is completed, as shown by the decreasing ratio of acid to copper in the various washes tabulated in Table 4, and also by the fact that 4.9 per cent. of the total copper in the ore remains in the tailings in a soluble form. Even though the extraction in leaching and the ampere efficiency in electrolysis would be benefited by keeping the salts in solution at a lower concentration, it is doubtful whether it would pay to decrease these salts by discarding more electrolyte without other changes in the, process, since this would increase the amount of cement copper produced, which is already very large. If, however, it would not disturb the process otherwise, this object could be accomplished by increasing the range of electrolysis, so that solution going to the tank house would contain, say, 4 per cent. copper and 1 per cent. acid, and the solution returned to the leaching plant 1 1/2 per cent. copper and 4.8 per cent. acid, and by increasing the volume of solution to be discarded, this to be taken from the electrolyzed solution returned to the leaching plant. By this arrangement, more salts will be removed from the system per ton of cement copper produced; and if sufficient solution is discarded to keep the iron content down to 1 1/2 per cent. it would he feasible to recover the copper from

Jan 4, 1919

By F. D. Rosi

The slip and twinning behavior in extended titanium crystals were studied in some detail. The formation and appearance of coarse kink bands are discussed. Their crystallographic geometry was determined by X-ray analysis. A phenomenological interpretation of the complexities in kink band development is also presented. The critical resolved shear stress, coefficient of shear hardening, and plane of fracture were determined for several crystals extended at room temperature. THE slip and twinning elements observed in the room-temperature deformation of titanium were enumerated in a previous paper1 in which considerations were advanced regarding the nature and selection of these elements and their effect on the known mechanical properties of this metal. The present study concerns the crystallographic, microscopic, and mechanical aspects of flow in relation to the slip and twinning elements, and includes a prediction of slip systems, nature of slip and twin markings, inhomogeneities of plastic flow, and stress-strain characteristics. Unless otherwise noted, arc-melted titanium sponge (99.77 pct) was used in these experiments. The method of production of crystals, their dimensions, and the surface preparation for micrographic examination have been reported.&apos; For obtaining stress-strain characteristics, only those crystals which traversed the entire width of the specimen and were at least 8 mm in length were used. Tensile deformation of the crystals was performed with conventional grips for sheet specimens and a constant-stress loading beam, designed after the method of Andrade and Chalmers.&apos; The specimens were loaded by allowing sand to flow from a reservoir into a bucket suspended from the longer end of a balanced 6:1 lever arm at a rate controlled to load the specimen approximately 2 kg per min. Strain measurements were made using the Baldwin SR-4, bonded, resistance-wire strain gage, Type A-8, which permitted a reading accuracy of 2 microinches per inch. The formulas used in the evaluation of shear stress and shear strain, as in deriving the coefficient of shear hardening, are given by Schmid and Boasv n terms of the original orientation and change in length of the crystal. For calculating the critical resolved shear stress, the standard equation was used. The crystallographic nature of the unpredictable slip observed in a number of specimens was determined by the single-surface X-ray method of analysis as described in ref. 1. Experimental Results Prediction of Slip System: It was reported&apos; that room temperature slip in titanium takes place predominantly on {10i0} and in a <1120> direction, giving three potential slip systems. Hence, it should be possible to predict the operative primary system in the manner used by Taylor and Elam&apos; for alu- minum (i.e., the one with the greatest component of shear stress in the direction of slip). The stereo-graphic construction in Fig. 1 shows that this is true. In all cases, slip was found to occur initially on the (0110) plane and, in a number of cases, in the [21f0] direction. (The direction of slip was not determined for all orientations.) It follows that duplex slip can be expected when two slip systems are geometrically equally favorable for slip, as demonstrated in Fig. 2. In both crystals slip took place simultaneously on the (1700) and (olio) prismatic planes, as indicated by Fig. 2a and b. In the case of crystal B the movement of the specimen axis with increasing extension was toward the (10i0) direction, which represents the stable end orientation resulting from alternate slip on the [2ii0] and [1120] directions. This is analogous to the duplex slip process in face-centered cubic metals." Unpredictable Slip: In a number of crystals whose orientations were well within the operation of a single slip system, secondary slip occurred on planes not predicted by the criterion of maximum shear stress. Examples are shown in Fig. 3. In addition to

Jan 1, 1955

The Alligator Ridge Project is owned jointly by Amselco Minerals Inc. and Occidental Minerals, with Amselco being the operator. It is the latest of Nevada&apos; s gold heap leaching operations , having gone into operation in October of 1980 after a design and construction period of only seven and one-half months. Alligator Ridge is located about 77 km (48 miles) northwest of Ely, Nevada. Three separate but adjacent ore bodies will be mined: Vantage I, II and III. The first lies virtually at the surface and is totally oxidized; the second is somewhat deeper and contains some carbonaceous material; and the third is at the lowest horizon and contains substantial carbonaceous ore. The ore is a Carlin- type siltstone which has been silicified, especially at depth, and contains finely disseminated free gold. Exploration drilling on Alligator Ridge resulted in the defining of an ore reserve of about 4.54 million mt (5 million st) averaging 4. 12 g Au per mt (0. 12 oz Au per st). A pilot heap leaching program was run during 1979. Because of the high content of fine material in portions of the ore body, one test heap of 5,000 tons was leached, after being crushed to 19 mm (314 in.), in the conventional manner using cyanide and caustic while a second heap of 2,500 tons of ore was agglomerated with cement before leaching. Results of this work were reported at the 1980 American Mining Congress meeting by Paul Chamberlin (see Bibliography). The test work clearly indicated the superior leaching qualities of the agglomerated ore, and the plant was designed on this basis. Run-of-mine ore is crushed in an open-air crushing plant using a jaw crusher followed by two cone crushers, one standard and one shorthead. Provision was made to bypass the shorthead when the ore is wet from rain or snow. Crushed ore at 19 mm (314 in.) size is mixed with cyanide solution and cement, with the ratio of the latter to the ore being 2 to 5 kg per mt (4 to 10 lb per st). The resulting moisture content is about 870, and the fines are effectively bound to the coarse particles so that migration of the fines in the heap does not take place during leaching. For agglomeration, Amselco uses a rotating drum 2. 75 m 0 by 6 m long (9 ft 6 by 20 ft). For the same agglomeration, Candelaria uses three "grasshopper" conveyors, with introduction of caustic- cyanide solution at the conveyor transfer points. Provision was made for future addition of cement slurry at these same points.

Jan 1, 1981

By D. P. Harris

This paper surveys a few of the quantitative exploration models that might be of interest to an ex-plorationist seeking to apply methods of operations research to mineral exploration. A general development of each model is presented, and the model is evaluated relative to the exploration activity. Finally, a philosophy of exploration and mineral resources is presented, and a possible exploration strategy incorporating concepts of some of these models consistent with this philosophy is proposed. The high cost of conducting an effective exploration program has generated an increasing interest in methods of optimizing the allocation of the resources of a firm engaged in mineral exploration. As a step towards this, mathematical models have been formulated which are designed to quantify those variables of mineral exploration in such a manner that they can be integrated with all phases of the firm&apos;s operations so as to optimize its profit objective. QUANTITATIVE MODELS General: Exploration models express at least two concepts: mineral occurrence and effectiveness of search. In simplest terms, an exploration model might be formulated mathematically as follows: P(X) = F(X) . G(X), where P(X) = the unconditional probability of discovery of X deposits, F(X) = the probability of occurrence of X deposits, and G(X) = the probability of discovery of X deposits, conditional upon their existence in the search area. With these general models as a basis of reference, some of the specific exploration models are examined below. The Allais Model: DEVELOPMENT - M. Allaisl performed the first study in which a philosophy of exploration was formulated into a probability framework. His objective was to estimate the economic profitability of the exploration of the Algerian Sahara. Allais divided the Algerian Sahara into blocks of land (called cells) 10 km square and defined the random variable, X, as the number of mining districts per cell. Thus, F(X) would describe the probability of 1, 2, or n mining districts occurring within any cell of the search area. Allais reasoned that his best information as to the form of the distribution, F(X), was the number of mining districts per cell that had been found in well explored areas in the world, such as the Western States of the U.S. He found that the Poisson function produced a reasonably good fit to the distribution of districts in these explored areas: where? is a parameter, such as the average number of districts per cell. Thus, by determining the value

Jan 1, 1968

By William P. Blake

In another paper I have described in general the close association of zinc-blende and iron pyrites in the ore-deposits of southwest Wis consin. These two minerals generally occur together at the same horizon, a sheet of one being overlain by a sheet of the other; and also the pyrites is disseminated through the blende to such a degree that the latter is rendered comparatively worthless for the produc tion of spelter. Ordinarily the pyrites, which is mostly the trimetric marcasite variety, occurs in about equal quantity with the blende and is separated by hand-culliug and chipping; but there are large de posits where the ores are so closely mixed that they can neither be separated by culling nor by any mechanical method. The specific gravity of the two minerals is so nearly the same that attempts often made to effect even a partial separation by jigging have proved un. successful. The smelters of zinc-ores in the Mississippi valley will not take ores which carry more than 7 per cent. of iron; and it is therefore necessary to cull the massive (&apos;jack" with great care and at consid erable expense, in order to bring it up to the market-standard of purity. The results of trials to effect a separation of blende and pyrites in other regions have been equally unsatisfactory. The literature of this branch of metallurgy abounds in examples. In Wisconsin efforts have been made in the past to " burn " the mixed ores in heaps, in order to soften or destroy the pyrites, and facilitate its separation from the massive blende. The same method has also been resorted to when galenite is mixed through the substance of the blende, for the purpose of disintegrating the ore, so that it could be separated by jigging. The custom was to pile the ore and the fuel together. As might have been expected, the results were far from satisfactory. As is usual in heap-roast ing, some portions of the ore were overheated and decomposed; zinc was lost by volatilization; the galenite in some portions was

Jan 1, 1894

By J. R. FINLA

THE three great war periods of recent times involving the-chief industrial, commercial, and military nations of the world have been the following: 1. Wars centering around the French Republic and Napoleon Bonaparte, .1791-1815;. involving every nation in Europe, parts of Asia Minor and *North Africa., and the United States of America. 2. Wars in Europe, Asia, and North -America beginning with the Crimean War, 1854-56, the British Empire, France, Sardinia, and Turkey against Russia; the Sepoy rebellion in India, -1857; -war of France . and Sardinia against ..Austria in Italy, .185.9; :the Taiping rebellion in China, 1861; Civil War in , America, 1861-65; French. occupation .of .M Mexico, .1863; Prussian war against :Denmark, :1864; (Prussia and Italy against Austria sand various -south German : states, 1866; :the Franco-German War, 1870.7,1.

Jan 1, 1931

By Carlos G. Valenzuela

The value generally accepted for stacking-fault energy, of copper has been approximately 40 ergs per sq cm based on Fullman&apos;s2 value for the coherent twin-boundary energy and the assumption that is twice the twin boundary energy However, Thornton and coworkers8 determined that the lower limit of for copper is approximately 60 ergs per sq cm, based on measurements of dislocation-node radii. They suggested that the assumption of = 2t is invalid. It is the purpose of this note to present results which indicate that the values of obtained by measurement of twin-grain boundary intersections and the values obtained by measurement of dislocation-node radii are actually compatible. The most reliable values for of the a brasses, based on electron-microscope observation of dislocation nodes, are probably those values reported by Smallman and Green6 who applied the Siems correction (1961) to data obtained by Howie and Swann.3 These values shown in Fig. 1 give an extrapolated value of approximately 70 ergs per sq cm for pure copper. In the present work, Fullman&apos;s method for determining the stacking-fault energy of copper was extended to the a brasses. High-purity copper (99.999 pet) and high-purity zinc (99.999 pet) were mixed in proportioned amounts and melted in sealed and evacuated quartz tubes. The alloys were homogenized for a week at 750°C and chemically analyzed by means of X-ray fluorescence. These alloys, along with a specimen of pure copper, were rolled to 98 pet reduction and a thickness of 0.009 in., resealed, and annealed for 40 hr at 715°C. Values for the ratio of twin-boundary energy to the grain-boundary energy, it gb, were obtained from measurements of dihedral angles formed at the intersections of twin boundaries and grain boundaries by using Fullman&apos;s2 mechanical analogy of surface tensions acting at the intersection of an annealing twin and a grain boundary. The angles between the twin traces and the grain boundaries were measured for a large number of twin-grain boundary intersections at a magnification of X500 using a rotating mechanical stage on a Reichert metallograph. The rotary stage has a calibrated angle scale with vernier so that measurements can be made to 0.1 deg. The mean twin-grain boundary energy and standard deviation were calculated for copper and each of the brasses by the use of an IBM 7072 computer. It was found that the mean value of gb stabilized after approximately 100 twin-angle measurements. This was determined by plotting the mean against the number of angles measured. Since the measured angles deviate from true dihedral angles, a correction factor for grain orientation, discussed below, was applied. The stacking-fault energy was then calculated from these values and the values of grain-boundary energy derived by Taylor.7 The data obtained are tabulated in Table I. Values for stacking-fault energy are plotted in Fig. 1. The value of gb for the specimen of 1.03 pet Zn is close to the value obtained by Fullman2 for OFHC (99.98 pet) copper, 0.045. It is believed that the purity of the copper affects gb significantly. The 99.999 pet purity Cu used in this investigation yielded a value of yt/ygb, 0.76, which is much higher than that obtained by Fullman. Additional evidence suggesting that the purity of

Jan 1, 1965

Michigan State Department of Conservation, Lansing, Mich The Department of Conservation has two divisions issuing publications which should be listed in this directory. Geological Survey Division. R. A Smith, State Geologist Land Economic Survey Division L R Schoenmann, Head. A price list of publications of either division will be sent upon request to that division Geological Survey Division.-Citizens of Michigan may obtain publications of this Division on payment of forwarding charges Prices to others for available publications are given below: Vol 5 (1881-1884): Pt 1, Geological report of the Upper Peninsula of Michigan, by L L Hubbard, pt 2, Geology of Lower Michigan with reference to deep borings, by A C Lane, $125. Annual Report for 1908. Pt b, Geological section of Michigan, by A C. Lane and A E Seaman, 50 cents. Publication No 5, The Late Glacial and Post Glacial Uplift of the Michigan Basin, and earthquakes in Michigan, by W. H

Jan 1, 1933

By C. Kremer Bain

DURING the past several years of diamond drilling in Washington County, Mo., the St. Joseph Lead Co. has discovered a concentration of commercial lead-zinc ore at four different points within an area of 36 square miles. The largest and to date the most promising group of these orebodies is located in the Indian Creek area. It was considered to be of sufficient value to warrant development. The Indian Creek area is in the center of the northern half of Washington County, 11 miles northwest of Potosi, Mo., the county seat. The location is readily accessible from Potosi by car or truck over the all-weather Missouri State Highway No. 114. The topography is one of rolling relief, varying from an elevation of 700 ft above sea level on Mineral Fork and Indian Creek to a maximum of 1176 ft at High Point Tower. It is divided in equal halves between the drainage to Mineral Fork and to Indian Creek. The shaft site at 1060 elevation is on the divide between the two drainage areas. The Indian Creek side is rough and heavily wooded, with only a few cultivated clearings. The slopes to Mineral Fork are more gentle and rounded, with much of the area cleared for farm land. Most of the surface is covered with Potosi and Eminence formations, which show little evidence of any structure. Ore structure was worked out by extensive diamond core drilling, with holes varying in depth from about 700 to 1300 ft. As of Oct. 1, 1950, 218 prospect holes had been drilled within the 36-square mile area. The ore is disseminated galena with considerable accompanying sphalerite in the Bonne Terre forma-tion in the shape of irregular blanket-type deposits. The main controlling structural feature of the outlined mineral zone is a buried pre-Cambrian rhy-olite-porphyry ridge extending partly through the Bonne Terre formation, which laps against the por phyry and also covers it. The mineralized zone parallels and forms an irregular halo around the porphyry ridge and is concentrated in the Bonne Terre formation where the La Motte sandstone is cut out by the porphyry ridge. This is a very common mineral occurrence in the southeastern Missouri lead belt district. The La Motte sandstone, which normally underlies the Bonne Terre formation, is thus cut out entirely. In this area the Bonne Terre is usually about 275 to 320 ft thick, the La Motte varying in thickness from zero up to 400 ft. Commercial concentrations of ore are indicated at several places, the most notable being at the shaft site where an orebody at least 4000 ft long with widths of 500 to 600 ft has been outlined. The total thickness of mineralized rock reaches 150 ft in some holes, although total ore thickness runs from 8 ft to about 60 ft, often in more than one layer. Preliminary Planning Ore reserves as outlined lend themselves to open-stope mining with trackless haulage and mobile loading machines and drilling equipment. This type of equipment has proved to be very efficient during recent years in the company&apos;s lead belt operations. After a study of bids for shaft sinking and an estimation of comparative costs, it was decided that the shaft would be sunk by St. Joseph Lead Co. personnel using company equipment. Since the plant site is about 26 miles from the company&apos;s nearest lead belt operations, it was necessary to plan a complete surface plant, including mill, shops, office, change room, and warehousing facilities. Immediately following the filing of an application for a certificate of necessity, a headframe was selected for which detailed drawings were already available. The order was placed for fabrication so that it could be delivered and erected in time to serve for sinking the shaft. This eliminated the expense of a temporary headframe. Drilling was started on two churn drill holes near shaft location, and two 1000-gpm deep well pumps

Jan 1, 1954

By P. Gordon

An isothermal jacket microcalorimeter, supplemented by metallographic, microhardness, and X-ray measurements has been used to study the isothermal annealing of high purity copper after room temperature tensile deformation. The amount of stored energy released during annealing has been measured as a function of deformation in the range 10.8 to 39.5 pct elongation. The data have shown the major heat effect to be associated with recrystallization and have allowed an analysis of the recrystal-lization kinetics and the calculation of activation energies of recrystallization. WHEN a metal is deformed plastically, some of the energy expended is dissipated as heat during the working process, while the remainder is stored within the metal in the form of lattice distortions and imperfections. During subsequent heating of the metal, the distortions and imperfections can be largely annealed out and the associated stored energy released as heat. It is apparent that measurements of the evolution of stored energy during such annealing may produce important information concerning the nature of the annealing mechanisms and the imperfections involved. Some excellent studies of this type have been made in the past, notably those of Taylor and Quinney,&apos; Suzuki,2 Bever and Ticknor,3 Borelius, Berglund, and Sjöberg,4 and Clarebrough et al.5,6 None of this work, however, employed isothermal techniques, with the exception of the Borelius studies&apos; in which only the early annealing stages were investigated. Since isothermal measurements, as compared with heating or cooling curve, have the merits that 1—they reveal the kinetics of a process more clearly, 2—the results obtained are more easily applied to theory, and 3—most fundamental investigations of annealing using techniques other than calorimetry have been carried out isothermally, it was considered important to apply calorimetry to the study of the isothermal annealing of metals. Accordingly, an isothermal jacket calorimeter of the Borelius type,&apos; supplemented by metallographic, hardness, and X-ray measurements, has been used to study the annealing of high purity copper after room temperature tensile deformation. Experimental The microcalorimeter has been described fully elsewhere." Briefly, the specimen to be studied is placed in a constant temperature environment of virtually infinite heat capacity achieved, as shown in the drawing of Fig. 1, by means of a vapor thermostat. A high thermal resistance is provided between the sample and the environment and a sensitive differential thermopile (see Figs. 2 and 3) arranged with half its junctions in contact with, and thus at the constant temperature of, the environment, and the other half in contact with the sample. A reaction in the sample develops a small difference in temperature, AT, across the thermopile, which is followed by a recorder-galvanometer set-up as a function of time, t, and is converted to reaction heat per unit time, P, by the use of the equation AT P=a?T + b AT dt The constants, a and b, in Eq. 1 are determined by a simple calibration, making use of the Peltier heat developed by a small current run through the junction of a thermocouple located in an axial hole in the specimen (Fig. 2). In its present form, the limit of sensitivity of the calorimeter is a heat flow of 0.003 cal per hr. The copper used was the spectroscopically pure metal supplied by the American Smelting and Refining Co. in the form of 3/8 in. diam continuously cast rod, reported to be 99.999+ pct Cu. A small amount of the copper was available at the start of this work and is referred to hereafter as lot A. A second batch, lot B, was obtained later, most of the results described subsequently being for this lot. As will be seen, there is some indication that lot A was somewhat purer than lot B, but it is not known whether this difference was present in the as-received metal or arose during subsequent handling. The two lots of copper were remelted and cast into two 1½ in. diam ingots in vacuo, using high purity graphite crucibles and molds. The ingots were upset several times to break up the large cast grains, and then rolled and swaged to rods 0.391 in. in diameter, using several intermediate anneals with about 40 pct reduction in area between anneals. The penultimate anneal was 2 hr at 350°C. X-ray examination showed no marked general preferred orientation in the resulting rods. The grain structure typical of the two rods is shown in the micrograph of Fig. 4." It was found to be virtually im- possible to get an unambiguous measure of the absolute grain size in the two annealed rods because of the profusion of annealing twins and the lack of regularity of the grain boundaries. However, counts of the number of boundaries intersected per unit length along a random line on a polished section, making a correction for the proportion of boundaries (about half) estimated to be twin boundaries, gave a figure of about 0.015 mm for the average grain diameter. The grain size of the rod from lot A was about 5 pct smaller than that from lot B. The rods were cut into 1 ft long bars and these deformed in tension at room temperature to various total elongations in the range 10.8 to 39.5 pct. A strain rate of 1 pct per min was used. The deformed bars were then stored in a dry ice chest until such time as samples were to be cut from them. Five bars deformed as indicated in Table I were used for the subsequent tests. In all cases, all the calorimeter.

Jan 1, 1956

By J. O. Brittain, N. R. Adsit

A number of zinc bicrystal specimens with the grain boundary loaded in simple shear were plustically deformed in creep in a vacuum at 200°C and under an argon atmosphere at 350°C. The results indicated that the amount of grain boundary sliding at a given time was controlled by the slip in the grains and was proportional to the resolved shear stress on the slip plane. Curves of grain boundary sliding vs time were found to be cyclic with no regular periodicity. ALTHOUGH grain boundary sliding (G.B.S.) has been investigated in a number of different types of tests on various materials there is substantial disagreement on the interpretation of the various observations. Gifkins1 has presented a comprehensive review of the subject of G.B.S. and fracture. He reports that the activation energy for high-temperature creep is equal to that for volume self-diffusion and that pure metals show less tendency towards intercrystalline fracture than alloys. Pure metals show appreciably greater grain boundary migration than alloys, and both grain boundary migration and grain boundary sliding follow the same general trend in time as plastic deformation during creep.&apos; While there have been a number of different mechanisms proposed to account for G.B.S., none of the models explains all the results. Since zinc has only one prominent slip system, it was hoped that experiments on G.B.S. in zinc bicrystals might enable us to separate the effect of grain boundary angle and the effect of matrix slip and thereby resolve at least one part of this complex phenomenon. EXPERIMENTAL PROCEDURE Bicrystals of pure zinc (99.99 pct) were grown by a Bridgeman technique in a furnace having a gradient of 20°C per in. The bicrystals were seeded to a desired orientation and grown in a split graphite mold which was 3/4 by 5/8 by 8 in. The mold was enclosed in a Pyrex tube and the tube was evacuated and then filled with a small amount of argon before it was placed in the furnace. The growth rates were 1/2 to I in. per hr for the bicrystals and 1/2 to 3 in. per hr for the single-crystal seeds. The longitudinal V notches served to hold the grain boundary in position during the growth process. A schematic rep- resentation of a specimen which had been cut with a jewelers saw from the bicrystals is shown in Fig. 1. All specimens of a series were cut from the same crystal, some of which were 7 in. in length. After specimen preparation the boundary was approximately 5/16 in. long and the V notches had a radius of 1/16 in. The boundaries were straight at a magnification of X100 with the exception of a few which had a gradual radius of curvature of greater than 3.2 in.-1. Laue back-reflection photograms were taken on the specimens to check the orientation of grains in the bicrystals. The method of relating the orientation of the two lattices is shown in Fig. 1, where 0 is the angle between normal to the boundary and the trace of the basal plane, is the angle in the boundary between the trace of the basal plane and a line parallel to the V notch, and x is the angle in the basal plane between the Burgers vector and the perpendicular to the grain boundary. After mechanical polishing the specimens were chemically polished.2 Subsequent to the polishing operation the specimens were encapsuled under a vacuum of better than 25 annealed at 340°C for 1 hr to remove the effects of this handling, and again chemically polished. Finally, fiduciary marks were scribed on the specimen using a micromanipulator. Creep tests, which were conducted in a modified Bausch apparatusS with the boundary loaded in simple shear, were run at a constant load (since the boundary area remained essentially constant this is approximately constant grain boundary stress). The temperature was controlled to ±1/4°C as measured on a semiprecision potentiometer with a calibrated thermocouple. The specimens were tested in a vacuum of better than 0.5 at 200°C and in purified argon at a pressure of 1/2 atm at 350°C. The op-

Jan 1, 1965

By M. O. Abo-el Fotoh, J. B. Mitchell, J. E. Dorn

The effect of strain rate and temperature on the tensile flow stress of a polycrystalline bcc alloy of magnesium containing 14 wt pct Li and 1.5 wt pct Al was investigated for strain rates of 3.13 x lom5 to 3.13 x 10-3 per sec over the range from 20° to 300°K. From about 180° to 300°K the alloy exhibited an ather-ma1 deformation behavior where the flow stress was independent of strain rate and increased only slightly with decreasing temperature. At lower temperatures the flow stress was strongly strain-rate- and temperature-dependent, characteristic of deformations controlled by thermally activated mechmzisms. The activation volume for thermally activated plastic defornzation was between 5 and 30 cu Burgers vectors, independent of plastic strain. This low-temperature thermally activated deformation behavior was found lo be in satisfactory agreement with the theoretical dictates of the Dorn-Rajnak1 formulation of the Peierls mechanism where deformation is controlled by the rate of nucleation of pairs of dislocation kinks over the Peierls energy barriers. SEVERAL studies of the low-temperature thermally activated deformation of bcc metals and alloys (molybdenum,1 tantalum,1 Fe-2 pct Mn,2 Fe-11 pct MO,3 and AgMg4) have revealed that the strain rate is controlled by the activation of dislocations over the Peierls-Nabarro energy hills. Although there is some uncertainty as to the nature and effect of solute atom-dislocation interactions during low-temperature deformation of bcc metals, it has been concluded by Dorn and Rajnak,1 Conrad,1 and Christian and Masters6 among others that overcoming the Peierls-Nabarro stress which arises from the variations in bond energies of atoms in the dislocation core as it is displaced is the probable mechanism controlling low-temperature deformation. The purpose of this research was to investigate the low-temperature plastic deformation of the bcc alloy Mg-14 wt pct Li-1.5 wt pct A1 to determine if the behavior of this alkali metal alloy might be analogous to that for other bcc metals. This alloy was selected because of its availability and its current industrial importance as a lightweight material for aircraft and aerospace applications. I) EXPERIMENTAL PROCEDURE Polycrystalline tensile specimens having cylindrical gage sections 2 in. long by 0.2 in. in diam were machined from as-received alloy sheet stock of Mg-14 wt pct Li-1.5 wt pct Al. Specimens were annealed in an argon atmosphere at 423°K for 4 hr and maintained in a kerosene bath together with the sheet stock to prevent corrosion. The resulting specimen microstructure consisted of a coarse uniform dispersion of incoherent precipitate MgLi2Al particles7 in a bcc 0 phase matrix having an average grain size of 150 p. Prior to testing the specimens were chemically polished in dilute hydrochloric acid. Comparison of tensile properties and microstructures of specimens cut from center and edge sections of the sheet stock revealed no effects of inhomogeneities in the sheet material. Tensile tests were performed on an Instron machine at crosshead speeds corresponding to tensile strain rates of 1.56 x 10-5 and 1.56 x 10"3 per sec. Stresses were determined to ±2 x 106 dynes per sq cm and strains to within ±0.0001. Average values of shear stress t and shear strain y reported were taken as one half the tensile stress and three halves the tensile strain, respectively. Flow stresses were taken at 0.05 pct strain offset. Test temperatures down to 77°K were obtained by immersing the specimens in constant-temperature baths. Lower-temperature tests were performed in a liquid helium cryostat to within ±2°K of the reported values. Prior to testing at the various temperatures and strain rates all specimens were prestrained at 2 35°K at a shear strain rate of 3.13 x 10-5 per sec to a stress level of 0.606 x 10&apos; dynes per sq cm to obtain a uniform initial state. Additional tests were made to determine the effect of changes in strain rate and strain on the flow stress by rapidly changing the crosshead motion during testing. Shear moduli of elasticity, needed for analyses of the data, were obtained at several temperatures by a common technique of determining the resonant frequencies of vibrations of rectangular test specimens. 11) EXPERIMENTAL RESULTS Fig. 1 shows the experimentally determined flow stress vs temperature for two strain rates. Two distinct regions of behavior are evident. Below about 180°K the strong increase in flow stress with increased strain rate and decreasing temperature indicates that deformation is controlled by a thermally activated dislocation mechanism. At higher temperatures an athermal region is evident where the flow stress is independent of strain rate and only slightly dependent on temperature. The applied stress t to cause plastic flow was separated into two components:

Jan 1, 1969

By John Wulff

In a previous paper Burwell and Wulff1 have shown by electron diffraction studies that allotropic transformations can be induced in 18-8 stainless steel by polishing to a depth of about 5 X 10-5 cm. The development of a successful etching technique, which removes accountable amounts of metal from the surface without pitting and without changing the root-mean-square profile as measured with an Abbot pro-filometer, led to the application of the whole technique and material to an investigation of various mechanical methods of surface preparation, such as grinding, lapping, superfinishing and cold-rolling. Ideally suited to such a study is 18-8 of low carbon and nitrogen content. The material can be heat-treated to produce a coarse-grained single-phase structure. On cold deformation there occurs not only a reduction in grain size but, at regions of maximum stress, a change of face-centered material to body-centered material, provided the metal is worked below about 200°C. When worked between 200"about and 415°C., diffraction studies evidence a reduction in grain size without the appearance of any new body-centered ferrite. Ferrite, which can be referred also to strains induced by carbide precipitation, is evident when the material is worked at temperatures between 4150 and 800°C. Stainless steel is advantageous because the usual surface-finishing operations do not readily oxidize it to any appreciable depth. In order to produce detectable oxide films on the surface of austenitic 18-8 in a time equivalent to that required to produce, for example, a fine ground finish on 1/2 sq. in., the sample must be held in a furnace or oxygen stream above 600°C. By using longer heating times, it is possible to achieve measurable oxide films on samples , whose surface temperatures exceed only about 250°C. Experimental Procedure The apparatus, material, and technique described in the previous paper1 were employed in this investigation. Samples of 18-8, I by I cm. by 4 mm., were carefully annealed in the austenitic range to produce a coarse-grained structure. They were then quenched and pickled to remove scale, On a lapping machine of the Graton2 type, both sides of each sample were polished to a a of 1/6 a wave length of sodium D light. Thereafter they were electrolytically etched to remove at least 1 X 10-3 cm. of the surface, a depth that is well below that of any defermations induced by surface preparation. samples of this material, carefully mounted in steel holders, were then sent to various industrial organizations known for special finishing techniques. In the instrue ment shops at the Massachusetts Institute of Technology check samples were finished by the same methods, as far as they were available. Abbot profilometer3 readings Were made on all the samples, which were then carefully degreased in double distilled benzine and alcohol, dried in a hot-filtered air blast, and kept in a desiccator. SUC-

Jan 1, 1941

By John Wulff

In a previous paper Burwell and Wulff1 have shown by electron diffraction studies that allotropic transformations can be induced in 18-8 stainless steel by polishing to a depth of about 5 X 10-5 cm. The development of a successful etching technique, which removes accountable amounts of metal from the surface without pitting and without changing the root-mean-square profile as measured with an Abbot pro-filometer, led to the application of the whole technique and material to an investigation of various mechanical methods of surface preparation, such as grinding, lapping, superfinishing and cold-rolling. Ideally suited to such a study is 18-8 of low carbon and nitrogen content. The material can be heat-treated to produce a coarse-grained single-phase structure. On cold deformation there occurs not only a reduction in grain size but, at regions of maximum stress, a change of face-centered material to body-centered material, provided the metal is worked below about 200°C. When worked between 200"about and 415°C., diffraction studies evidence a reduction in grain size without the appearance of any new body-centered ferrite. Ferrite, which can be referred also to strains induced by carbide precipitation, is evident when the material is worked at temperatures between 4150 and 800°C. Stainless steel is advantageous because the usual surface-finishing operations do not readily oxidize it to any appreciable depth. In order to produce detectable oxide films on the surface of austenitic 18-8 in a time equivalent to that required to produce, for example, a fine ground finish on 1/2 sq. in., the sample must be held in a furnace or oxygen stream above 600°C. By using longer heating times, it is possible to achieve measurable oxide films on samples , whose surface temperatures exceed only about 250°C. Experimental Procedure The apparatus, material, and technique described in the previous paper1 were employed in this investigation. Samples of 18-8, I by I cm. by 4 mm., were carefully annealed in the austenitic range to produce a coarse-grained structure. They were then quenched and pickled to remove scale, On a lapping machine of the Graton2 type, both sides of each sample were polished to a a of 1/6 a wave length of sodium D light. Thereafter they were electrolytically etched to remove at least 1 X 10-3 cm. of the surface, a depth that is well below that of any defermations induced by surface preparation. samples of this material, carefully mounted in steel holders, were then sent to various industrial organizations known for special finishing techniques. In the instrue ment shops at the Massachusetts Institute of Technology check samples were finished by the same methods, as far as they were available. Abbot profilometer3 readings Were made on all the samples, which were then carefully degreased in double distilled benzine and alcohol, dried in a hot-filtered air blast, and kept in a desiccator. SUC-

Jan 1, 1941

By F. X. Meyer

THE United States Smelting Refining and Mining Company maintains an ore-purchasing department for procurement of custom tonnages of milling and smelting ores and concentrates for treatment at its Midvale plant. Arrangements with other companies provide for treatment of Company and custom zinc concentrates. Location of the Midvale plant in the heart of the Western mining country makes it possible to serve shippers from these nine producing states: Arizona, California, Colorado, Idaho, Montana, Nevada, Oregon, Utah, and Washington. Shipments from most of these states travel over main-line railroads, delivery being made at Midvale within a short time after billing of the shipment. Shipments varying in size from a few sacks to carloads can be handled at

Jan 1, 1948

By F. M. Lewis, J. F. Myers

The paper reports the development of a large, slow speed ball mill closed circuited with a hvdro-scillator. This increased grinding efficiency 28 pct over conventional units. AS the title indicates, this is a progress report for the first year of experimental operation of a relatively large diameter, slow speed ball mill with 1-in. balls, with and without various classifiers, and including a hydroscillator. Several years ago the authors came to the conclusion that if any further progress were to be made in our flotation process, an understanding of the chemical and physical reactions and the control thereof, in the grinding circuit, was essential. It may be stated, at this point, that the preparation of a correct feed for the flotation process is still the number one objective of our grinding studies. This progress report deals with grinding "per se," and not with the chemical and physical reactions as the result of grinding. Prior to this time we had taken the naive position, that since grinding had been practiced by the industry for some fifty years or more, it had been well exploited and developed by a host of investigators. Consequently, we had given the matter only superficial attention. At the start of our study, we were aware of the fact that some difference in opinion existed, but we were not prepared for the controversial evidence that developed nor for the extent to which the experts differed in their viewpoints. There seemed nothing else to do but to tour the continent and decide for ourselves what was right and what was wrong, read all the published literature and visit with anyone who had ideas about the matter. This we did over the next few ensuing years. Since our study has met with some measure of success, we report, herewith, these data that ultimately they may be of help to other investigators. In 1944 it became necessary to increase our grinding capacity and at the same time to grind the sulphide portion a little finer. This provided the impetus to put our ideas into effect. As has been previously described, our grinding flowsheet at that time consisted of a 6x12 rod mill, followed by two 5x10 ft, and one 6x12 ft trunnion overflow ball mills, with conventional rake classifiers. Naturally, we first considered all the possibilities of altering or adding to the existing equipment. It became evident that if any appreciable increase in grinding efficiency could be obtained, it would pay to scrap the existing small mills and classifiers and install one big mill with adequate classification. Trying to determine just how much more efficient a big mill could be, in which were incorporated all

Jan 1, 1951

By J. F. Myers, F. M. Lewis

The paper reports the development of a large, slow speed ball mill closed circuited with a hvdro-scillator. This increased grinding efficiency 28 pct over conventional units. AS the title indicates, this is a progress report for the first year of experimental operation of a relatively large diameter, slow speed ball mill with 1-in. balls, with and without various classifiers, and including a hydroscillator. Several years ago the authors came to the conclusion that if any further progress were to be made in our flotation process, an understanding of the chemical and physical reactions and the control thereof, in the grinding circuit, was essential. It may be stated, at this point, that the preparation of a correct feed for the flotation process is still the number one objective of our grinding studies. This progress report deals with grinding "per se," and not with the chemical and physical reactions as the result of grinding. Prior to this time we had taken the naive position, that since grinding had been practiced by the industry for some fifty years or more, it had been well exploited and developed by a host of investigators. Consequently, we had given the matter only superficial attention. At the start of our study, we were aware of the fact that some difference in opinion existed, but we were not prepared for the controversial evidence that developed nor for the extent to which the experts differed in their viewpoints. There seemed nothing else to do but to tour the continent and decide for ourselves what was right and what was wrong, read all the published literature and visit with anyone who had ideas about the matter. This we did over the next few ensuing years. Since our study has met with some measure of success, we report, herewith, these data that ultimately they may be of help to other investigators. In 1944 it became necessary to increase our grinding capacity and at the same time to grind the sulphide portion a little finer. This provided the impetus to put our ideas into effect. As has been previously described, our grinding flowsheet at that time consisted of a 6x12 rod mill, followed by two 5x10 ft, and one 6x12 ft trunnion overflow ball mills, with conventional rake classifiers. Naturally, we first considered all the possibilities of altering or adding to the existing equipment. It became evident that if any appreciable increase in grinding efficiency could be obtained, it would pay to scrap the existing small mills and classifiers and install one big mill with adequate classification. Trying to determine just how much more efficient a big mill could be, in which were incorporated all

Jan 1, 1951

By R. R. Templeton

THE year 1924 was particularly notable in the petroleum industry of California as it was a period in which extensive town-lot drilling, with attendant overproduction and allied problems, virtually ceased and the industry returned to a nearly normal condition. Nearly all major field operations were conducted by large operating and marketing companies; in contrast to 1922 and 1923 field operations, when small promotion companies set the pace and forced the large companies to follow. The outstanding features of petroleum development were: 1. The three major fields of 1923, namely Huntington Beach, Long Beach, and Santa Fe Springs, declined from a production of 13,042,939 bbl., in January, to 6,764,417 bbl., in December, a drop of nearly 52 per cent: During this period, Huntington Beach declined 35 per cent., Long Beach 42 per cent., and Santa Fe Springs 63 per cent. 2. Methods of pumping deep wells were improved in some particulars; this contributed toward sustaining the productions of these three famous fields above what was predicted. 3. Of the fields producing previous to 1924, only three increased in production to any appreciable degree, during the year, as the result of bringing in new wells. These fields are Dominguez, Torrance, and Wheeler Ridge. Dominguez, discovered in September, 1923, produced 56,851 bbl. in January and increased regularly to a production of 1,641,042 bbl. in December. Torrance increased from a production of 972,261 bbl. in January, to 1,783,670 bbl., in May, and then declined to 1,393,215 bbl. in December. Wheeler Ridge, discovered in January, 1923, produced 23,254 bbl., in January, 1924, increased to a high of 33,678 bbl., in September, and declined to 27,430 bbl. in December. 4. Nearly all the production that had been shut-in during 1923 was opened in 1924, except some wells chiefly in Coalinga, Fullerton, and Santa Maria districts. The opening up of this shut-in production, combined with the increased productions from Dominguez and Torrance, were the chief factors that held the rate of decline for the state to a gentle slope.

Jan 7, 1925