Search Documents

By J. Engesser

A research project was undertaken to determine if coal addition tofluxed-magnetite pre-fired pellets would reduce nitrogen oxide (NOx)emissions during pellet induration. Iron oxidation rate tests, coal oxidation rate tests and calcination rate tests were conducted in a laboratory furnace to determine the amount of coal necessary to provide adequate heat for limestone calcination without producing detrimental effects to magnetite oxidation. Pilot scale pot-grate tests were then performed with and without coal in the pre-fired pellets to verify pellet quality parameters and nitrogen oxide emissions. The off-gas during each pot-grate test was analyzed for NOx, CO2, CO, SOx, and O2. There was approximately a ten percent reduction in NOx emissions with coal addition during the normal pot-grate firing cycle. There was a 75% reduction in NOx emissions during firing cycles that used 25% to 75% excess air during firing rather than the normal 300% excess air.

Jan 1, 2003

By Ramesh Kumar Chauhan, Umakant Sharma, Manwendra Pratap Singh, Ashok Kumar Chadha

The power sector in India has an installed capacity of 267.637 GW as on March 2015. Out of this total installed capacity, the hydropower sector contributes 41,267.43 MW as renewable energy source. The development of various proposed hydropower schemes in India are primarily concentrated in mountainous regions of Himalaya and often involves underground tunnelling. Underground tunnelling of considerable magnitude is generally associated with adverse geological conditions and associated geological surprises. The main objective in case of Tunnels constructed especially for hydro projects, which carry enormous quantum of water is that, it should not leak. Moreover, the tunnels which are part of water conductor system should resist the inflow of water from the surrounding ground in order to avoid draining of natural water sources and lowering of existing groundwater levels. Lowering of water table may result in subsidence and damage to existing surface structures, loss of capacity of drinking water schemes and in some cases even catastrophic sliding of landmass. Grouting and pre-grouting in tunnels serve three different purposes i.e., Stabilization, Strengthening and sealing of the rock mass around tunnels to avoid leakage of water from tunnels. In present paper, results of grouting methodology adopted during final construction stage of RHEP (412 MW) along with the introspection of Water Pressure Tests conducted for determination of the efficacy of grouting were elaborately presented. The process, of contact and consolidation grouting which is respectively followed by water pressure tests along entire reach of HRT (15.177 Km long) were also addressed in detail. Pertaining to the results of water percolation tests (before and after consolidation grouting), it was also attempted to categorize the behaviour of different rock mass classes/ conditions in reference to different quantum of grout intake and corresponding Lugeon values. Importance of planned and dedicated successful grouting procedure adopted in hydropower project at RHEP is also emphasized.

Jan 1, 2016

By John J. Friel

The addition of dolomite to iron ore pellets improves their high-temperature reduction properties primarily by increasing their reducibility and raising their softening temperature. In this study we prepared dolomite-fluxed pellets from three different concentrates; Hibbing, a magnetic taconite, Knob Lake, an earthy hematite; and Carol Lake, a mixture of specular hematite with magnetite. The composition n of the concentrates is given in Table I. The pellets were subjected to standard physical tests and the following reduction tests: low temperature degradation, swelling, softening, and thermogravimetric analysis. Petrographic examination and electron microprobe analysis allowed us to evaluate the effect of composition and firing on the phase assemblage. Further, we were able to interpret the test results in terms of chemistry and microstructure. This approach enabled us to determine which fluxed composition best suited each of the concentrates.

Jan 1, 1980

By L. Michael Kaas

Any increasing number of restrictions are being placed on mining management's ability to pursue profit. Raw materials pricing, the cost of capital equipment, labor cost, and overhead costs, are becoming more difficult to control. Cost reduction is one of the few remaining areas in which management may still exercise its profit making ability. Equipment maintenance is an area where mine and mill management can readily reduce costs and increase profits. Why is this possible? First, maintenance costs comprise a large portion of total operating cost. Thirty to sixty percent of the operating cost dollar is not unusual. Even a relatively small percentage reduction in this cost represents a very sizeable increase to mining profitability.

Jan 1, 1967

By R. J. Clements

The waterway transportation system in the united states consists primarily of the Mississippi river system. With its navigable tributaries, it is 12,500 miles long. This system naturally accesses about 40 percent of the nation. With its connecting railroads and highways, the river system accesses the united states from the Appalachian mountains in the east to the rocky mountains in the west. Within this area is the vast majority of our agricultural, industrial and material resources.

Jan 1, 1984

By Ted Klemetti

Roof deterioration in weak moisture-sensitive rock leads to roof falls in coal mines. An observation site was set up in intake air at an underground coal mine in central Ohio to evaluate the time-dependent deterioration of moisture-sensitive roof rock. By periodically collecting and weighing the rock falling from the roof, the National Institute for Occupational Safety and Health (NIOSH) was able to quantify the deterioration of the moisture-sensitive shale roof. The measurements showed that more roof rock is falling in the dry winter months. Movements in an intersection were monitored in order to determine if deformation correlated with seasonal changes in temperature and humidity. The rate of intersection roof-to-floor convergence was found to be cyclical and related to seasonal changes, with more convergence during the months of April through September. At the study site intersection, the roof beam did not show deflection indicating movement most likely due to mine floor deformation. The bolt load also increased in the warmer months before shedding load, possibly due to rock failure. Temperature and relative humidity sensors, placed in holes in the roof show that mine air does not mix with the air in the holes. Consistent saturation levels of relative humidity were measured in the holes and it appears that high levels of moisture may have migrated into the bolt holes from roof shales. A roof sealant applied to a portion of the test roof appears to be preserving the roof and reducing the amount of rock fall into the entry, while the screened area virtually eliminated rock falling from the roof.

Jan 1, 2009

By Mark Leggett, Kevin Roberts

The need to modernise and increase the safety provision of older road tunnels raises challenges in maintaining the operation of the tunnel during such improvement works. The Mersey Kingsway twin road tunnels located in Liverpool UK, constructed in the late 1960s, have had three new cross passages constructed to allow emergency evacuation from one tunnel to the other tunnel and provide safer access for emergency services. The 3200m long road tunnels are lined with an unusual reinforced concrete steel-faced segmental lining with a paint finish. Construction of the cross passages occurred during night possessions with the tunnels returned to normal operation during the daytime. Constructed through water bearing sandstone and lined with precast concrete segments, the passages required advance ground treatment and support works. This paper presents the historical background to the Mersey Tunnels and describes the procurement strategy, design and construction approach adopted for these important safety improvements.

Jan 1, 2003

By A. Vaillant

Classifiers that are used to separate granular materials into a coarse and a fine stream, are considered. Fundamental Equations are presented which apply to all, such Classifiers and all feed size distributions. The practical, real Classifier is compared quantitatively with the perfect. Classifier. A Formula is introduced for the Real Classifier Selectivity, that defines what portion of each particle size is sent to the coarse outlet duct. This selectivity function is characterized by three Parameters, one of which (b) is a numerical measure of the sharpness of classification. A new dimensionless variable (J) appears in Equations and Graphs for recirculating load, product size distribution and specific surface in the classified product. This variable combines the effects of sharpness of separation, Classifier setting and fineness of a Rosin-Rammler Type feed to the Classifier. Classifier efficiency is defined, based on Specific Surface.

Jan 1, 1967

By William E. Cutcliffe, John A. Ames, John D. MacFadyen

Webster's dictionary nearly equates portland cement with its current primary definition of cement. Although such equation may be a triumph of common usage, the confusion between the terms cement and concrete unfortunately is very widespread. Full definition of cement properly would extend to many substances, but for purposes of this chapter cement is restricted to varieties of portland cement including portland-pozzolan cement. Among the usually recited historical notes concerning cement is that it was developed by the Romans. Their use of cement in the great structures of Rome, and even in the far comers of their Empire, such as Hadrian's Wall in the north of England, testifies to the antiquity of a major cement industry. From English sources we know of John Smeaton's carefully proportioned hydraulic cement mixed in 1756 and of Joseph Aspdin's patented cement to which, in 1824, he gave the name portland cement. (He claimed that his cement mortar looked like the famous dimension limestone quarried from the Isle of Portland on England's south coast.) The year 1971 marked the centennial of portland cement manufacture in the United States. A fair historical account of the many real contributors to the cement industry since 1756 unfortunately would be too extensive for this chapter. Development of rotary kiln practice and burning at higher temperatures clearly was the major move into today's technology. Cement manufacture is the processing of selected and prepared mineral raw materials to produce the synthetic, mineral mixture (clinker) that can be ground to a powder having the specified chemical composition and physical properties of cement. Cement making incorporates a number of distinct steps, but it is characterized by the key pyroprocessing (or burning) step, which brings about the necessary changes in the raw materials. This pyroprocessing is a chemical process. Conversion of large volumes of mineral raw materials into specification-controlled cement at relatively low cost is the objective. Statistics on the cement industry are of uneven quality. The US Bureau of Mines (USBM) is the principal collector of available data. These statistics can be only as good as the quality of information supplied by the reporting companies. The data perhaps most often questioned relates to productive capacity of the industry. The questions submitted by USBM are valid, nevertheless, and the information gained from them, as good as is available, is what is generally used. The Portland Cement Association also is a source of much quality information. In analyzing cement industry production rates, it is well to keep in mind that measurement of raw materials requires the reader to recognize that approximately 1.6 t of dry raw materials are required to make 1 t of clinker. This number can vary depending on the amount of kiln dust wasted. Also that to produce 1 t of portland cement required .94 to .96 t of clinker, the remainder being gypsum or anhydrite. A ton of masonry cement or pozzolanic cement re- quires considerably less clinker.

Jan 1, 1994

By R. J. Sweigard

One of the foremost problems in reclaiming prime farmland is compaction of the subsoil which is caused by the reclamation equipment. Wheel tractor-scrapers are most commonly used to replace subsoil and have been blamed for the majority of the compaction problems. Two methods of alleviating this problem that are presently being considered are mechanical subsoil loosening machines and truck- shovel combinations for subsoil handling. A field study was conducted in which dry bulk density measurements were taken in an effort to determine the effectiveness of truck-shovel combinations and subsoil loosening equipment in reducing bulk density in comparison to typical scraper replacement.

Jan 1, 1987

By Eugene P. Pfleider

The mining industry of the World, and particularly of the United States, has made a complete reversal from underground to surface mining methods since the turn of the 20th Century. This has occurred even as average ore grades were decreasing and strip ratios rising. In the early 1900's there were over 100 underground mines producing from the three iron ranges of Minnesota -- today there are hone. Practically all of our coal prior to 1930 was mined underground; today over one-third is from surface operations and that percentage is increasing. Although world mining has hot changed to surface techniques as rapidly as has the U. S. Industry, the shift is escalating and will approach our figures shortly. A comparison of World and U. S. production figures are shown in Table 1, taken from the AIME Surface Mining volume, and the trend rates for the U. S. are depicted in Fig. 1.

Jan 1, 1968

By O. Lopez

"Stringent regulations and increased arsenic presence in ore bodies being exploited have created the need for cost effective and environmentally compliant technologies to remove selenium and arsenic from mine waters and metallurgical waste streams. Existing treatment methods have high life cycle costs and/or produce residues that, due to their unknown stability over the long-term, may represent future liabilities. This results in high compliance costs and uncertainties which negatively impact existing operations and projects in permitting. Selen-IX™ is a new ion exchange based process that selectively removes selenium from mine impacted waters down to 1 ppb while producing a stable inorganic iron-selenium product. Results of piloting completed on streams generated from coal and copper-gold deposits are presented along with preliminary equipment sizing and life cycle costs of full scale treatment. An example of a commercially available system for arsenic removal using sulphide precipitation is presented. The benefit of this treatment method is discussed based on recently completed technical feasibility assessment including laboratory testing and preliminary engineering design. INTRODUCTION Selenium Due to the chemical similarity between selenium and sulfur, selenium substitutes sulfur in many minerals that can be found in a wide range of deposits including coal, base metal, precious metal, phosphate, and uranium. One of the main environmental challenges facing the industry in North America today is related to the removal of hexavalent selenium, e.g. selenate, to ultralow levels, typically between 1 to 10 ppb, from large flows of often cold water containing less than 1,000 ppb of selenium. Recent studies commissioned by the industry identified biological selenium reduction systems as the best available technology. Although the biological selenium reduction process is commercially proven in certain applications to remove selenium to ultralow discharge levels, the technology has been primarily applied to relatively low and constant flows of warm water produced by the Flue Gas Desulfurization (FGD) scrubbers in the power generation industry. The wide spread adoption of this treatment method by the mining industry is hindered by high capital and operating costs associated with treating large flows of cold water, lack of data and knowledge about the long term stability of solid residues produced by this treatment, and limited capacity of biological systems to respond to sudden changes in flow and/or mass load of contaminants. Furthermore, it has been reported that reaching discharge limits less than 3 ppb could be a challenge and that polishing treatment for the removal of BOD and phosphate maybe required to avoid the impact of the biological treatment which requires organics and nutrients, on aquatic environment downstream of treatment plants. Alternate treatment systems are being developed to overcome and/or completely avoid some of the challenges of biological systems. One such treatment system is BioteQ’s Selen-IX™ process which is purely physico-chemical treatment system."

Jan 1, 2015

By G. S. Adisoma, J. J. K. Daemen, R. O. Roko

A common assumption in determining the shear strength of a rock joint using a direct shear test is that the surfaces undergoing relative shear are in complete contact. Furthermore, the limiting displacement associated with the residual strength values is obtained based on engineering judgement through visual inspection of shear force versus displacement curves. This study proposes a systematic way of determining the residual shear strength of rock joints by evaluating the limiting displacement leading to a minimum cohesive strength value and taking the true area of contact into account. The results of the study indicate that there is a limiting displacement associated with the residual shear strength, and some rocks may have an inherent interface residual cohesive strength different from zero. When the cohesion is different from zero, the residual shear strength is likely to be underestimated if the true area of contact is not considered. In the case where zero calculated cohesion is obtained, the area of contact has no bearing on the shear strength equation because the frictional force depends only on the normal load.

Jan 1, 1986

By R. W. Smith, D. Clare

The removal of metals from an acid mine drainage (Leviathan Mine, Alpine County, California) water by precipitate flotation was investigated. The Leviathan waters vary from about pH 4.0 to pH <2.0and contain from about 2,000 to about 12,000 ppm SO42-.The main multivalent metals present in solution are Fe, Ca, Mg, Al and Mn. Both Cu and Co are present in small amounts. The pH was adjusted with lime. The collector used was either sodium oleate or tall oil. The sodium oleate was used as a function of pH to establish optimum flotation conditions and the tall oil was used only at the optimum pH. Dow Froth 250 was used as a frother. In some test additional Cu was added to the system. Excellent recovery of Fe and Cu were achieved at optimum pH. The process achieves results comparable to precipitation and filtration without as much problems with screens blinding because of less material to filter.

Jan 1, 2004

By Robert H. Merrill

7.1-STABILITY OF SLOPES IN SOIL AND ROCK ROBERT H. MERRILL 7.1.1-DESIGN ANALYSIS APPROACHES The analyses of slopes in soil or rock can be made through application of soil- or rock-mechanics principles. In most cases, the material in the slope wall can easily be identified as either a soil or a rock. However, there will be instances where, because of unique characteristics, the soil may behave as a rock structure, or vice versa. By necessity, these unique cases must be identified through experience or critical observation by the engineer, because there are no definitive rules clearly establishing the differences. The most important step in a solution to a slope problem is to define it. Normally, once the problem is identified, a solution usually can be found or a reasonable estimate obtained. The design analysis of a slope wall implies an evaluation of the stresses or forces in the wall, and of the ability of the material in the wall to withstand them. Therefore, the factors influencing a design analysis can be divided into two categories: those which influence stresses, and those which influence the ability of the wall to withstand stress. For simplification, the latter is termed the strength of the soil or rock. Perhaps the basic difference between analyses for soils and those for rock is in the identification of the failure surface. Soils generally do not have an identifiable failure plane. However, some soil layers in a slope wall may have different strengths. A soil slope wall may consist of a thin layer of topsoil overlying a thick, uniform clay, or a topsoil over a gravel or other materials. Therefore, the soil generally does not have a potential plane of weakness that can be identified through observation. On the other hand, rocks normally contain planes of weakness in the form of fractures, faults, joints, bedding planes or other discontinuities weaker than the intact rock, which can be found through observation and/or tests upon rock samples. If the failure surface cannot be identified, the principles of soil mechanics should apply because, in soil mechanics, the failure surface usually is assumed. If it can be identified, then the principles of rock mechanics should apply. 7.1.2-ANALYSES OF STRESSES OR FORCES IN SLOPES All existing methods of soil-slope analysis are based upon interpetations of the Coulomb and Coulomb-Navier failure criteria, commonly termed the total-stress 2nd the effective-stress criteria (Sec. 6.1). The total-stress criterion may be illustrated by the diagram in Fig. 7-lA, which relates the total stress, S, to the cohesion, c: the normal stress, u, and the angle of internal friction, 9, by the expression

Jan 1, 1973

By J. Routh

Analysis of AI, As, Ba, Be, Ca, Cd, Co, Cu, Fe, K,. Mg, Mn, Mo, Na, Ni, Pb, Sb, Se, Sr, 11, V and Zn in various types of samples collected at Van Stone mine (a Pb-Zn deposit in Washington) and surrounding areas indicates that the concentrations of several elements in water, soil and sediment are higher than their background. values. Concentrations of metals in water decrease sharply downstream and are below the maximum contaminant levels specified for drinking water. Under present physico-chemical conditions, contamination of water is insignificant but the enrichment of heavy metals is found in soil and sediment.

Jan 1, 1994

By Jon Y. Kaneshiro, Stephen J. Navin, Jerry Ostberg

In 1968, the U.S. Bureau of Reclamation awarded S.S. Mullen Construction of Seattle, the Intake Tunnel (488 m by 4 m diameter tunnel) and Pumping Plant No. 1. In1998, the Southern Nevada Water Authority awarded Lake Mead Constructors (Kiewit of Omaha) a parallel New Intake Tunnel (518 m long by 4.6 m diameter tunnel) and Pumping Plant. Both projects provide water to a thirsty Las Vegas. This paper presents a detailed comparison of the two intake tunnels in terms of grout takes and pressures, geologic mapping and rock quality, grout penetration beyond the excavation line, degree of fracture grouting, and groundwater inflow boundary considerations. The paper provides a comparison of grouting techniques and material developments then and now.

Jan 1, 2001

By Eddie Woods, Jon Hurt, Roger May, Paul Watson

The Channel Tunnel Rail Link (CTRL) will be Britain’s first major new railway for over a century—a high-speed line running for 109km (68 miles) between St. Pancras station in London and the Channel Tunnel. The new line has been under construction since October 1998 and the first phase will open in October 2003. The project includes22km of twin 7.15m ID TBM bored tunnels under London and the River Thames, and the 3km North Downs Tunnel, the first major NATM tunnel to be constructed in the United Kingdom since the collapse of the Heathrow Express Tunnels in 1994. This paper will discuss the design of these tunnels and describe the construction progress to date. The discussion will include details of segmental lining design, TBM specification, and sprayed concrete lining design.

Jan 1, 2003

By K. Feledi

"A booster fan is an underground mechanical ventilation equipment installed in series with a main surface fan that is used to boost the air pressure provided by the surface main fan passing through it. As mining continues to expand and go deeper, the need for improved and efficient ventilation increases. This has led to the use of booster fans and other auxiliary ventilation devices in underground mines. This paper details experiments and results carried out at Missouri S&T Experimental Mine that investigated air leakage and recirculation caused by the use of booster fans. The results were compared with the situations where booster fans are used and not used.The variables considered were the booster fan blade angle and the fan combinations. Air quantity measurements were taken at each individual stopping under a number of scenarios and across four blade angle settings. The first set of situations examined were; the main surface Joy fan only running, the main Joy, and the west booster fan running, and the main Joy fan and east booster fan running. Observations were made which lead to the conclusion from the experimental analysis that booster fans affect the behavior of leakage and recirculation. The locations of the booster fan and the blade angle setting have the most effect on leakage and recirculation. To limit the potential for system leakage and recirculation, the location and size of a booster fan in a ventilation system should be thoroughly evaluated.INTRODUCTION Missouri S&T Experimental Mine ventilation system The Missouri S&T Experimental Mine has two shafts. One currently serves as the main intake shaft. Air is forced through the main shaft by a Joy Manufacturing Vane Axial fan and follows the direction shown on the map on Figure 1. The air is currently naturally exhausted through the Wheeler portal. As indicated on the map there are eight stoppings in the mine, with stoppings number 2 and 8 fitted with man doors. The mine also consists of three raises which are either fully or partially blocked, two portals with one acting as an exhaust and the other generally closed by a hydraulic Kennedy door."

Jan 1, 2015

By Keiichi Fujita, Michio Miyoshi, Hisashi Miyazaki

In the construction of "Hamacho" subway station (Tokyo Metropolitan Rapid Transit), in order to minimize ground surface settlement, the pipe-roof method was employed as an auxiliary measure when removing the portion between two parallel shield tunnels to form one large tunnel for the station. 14 steel pipes (dia.1,219.2mm, length 75m) were driven in horizontally so as to cover tunnels and support heavy and extremely soft covering soil and surface structures. Procedures of temporary supporting, excavation under compressed air, reinforcing, concreting, etc., and some comparisons with conventional methods are described.

Jan 1, 1979