Search Documents

By M. R. Shahan, C. E. Seaman, Mischler S. E., T. W. Beck

"Float dust deposits in coal mine return airways pose a risk in the event of a methane ignition. Controlling airborne dust prior to deposition in the return would make current rock dusting practices more effective and reduce the risk of coal-dust-fueled explosions. The goal of this U.S. National Institute for Occupational Safety and Health study is to determine the potential of open-air water sprays to reduce concentrations of airborne float coal dust, smaller than 75 µm in diameter, in longwall face airstreams. This study evaluated unconfined water sprays in a featureless tunnel ventilated at a typical longwall face velocity of 3.6 m/s (700 fpm). Experiments were conducted for two nozzle orientations and two water pressures for hollow cone, full cone, flat fan, air atomizing and hydraulic atomizing spray nozzles. Gravimetric samples show that airborne float dust removal efficiencies averaged 19.6 percent for all sprays under all conditions. The results indicate that the preferred spray nozzle should be operated at high fluid pressures to produce smaller droplets and move more air. These findings agree with past respirable dust control research, providing guidance on spray selection and spray array design in ongoing efforts to control airborne float dust over the entire longwall ventilated opening. IntroductionCoal mining processes produce airborne dust that naturally deposits on the floor, roof and ribs of mine airways. These fine dust particles, termed float coal dust when smaller than 75 µm in diameter, are deposited in the return entries of coal mines and can be reentrained by pressure waves induced by methane-air explosions (Rice et al., 1911; Nagy, 1981; U.S. National Institute for Occupational Safety and Health (NIOSH), 2006). These particles are also those most likely to participate in coal-dust-fueled explosions, which can potentiate and propagate explosions resulting in extensive damage. In order to meet compliance requirements of at least 80 percent incombustible content in the composition of material deposited in mine entries (U.S. Mine Safety and Health Administration (MSHA), 2016), coal mines apply an inerting agent, specifically, rock dust (Harris et al., 2009). Should methane be present in the mine atmosphere, the required fraction of incombustible content is further increased by 0.4 percent for each 0.1 percent methane. The removal of airborne float coal dust (AFCD) prior to deposition is an approach intended to make current rock dusting practices more effective by increasing the proportion of inert material to combustible material, resulting in a lower risk of coal-dust-fueled explosions."

Jan 1, 2018

By S. Noll

Ventilation is an essential part of any underground mining operation. It provides fresh air for workers and machinery, keeps up an adequate mine climate and dilutes and dissipates noxious gases. Possible changes in the economic environment for mining in the future, e.g. increasing energy costs, will necessitate optimization of distribution of airflow within most mines. This paper discusses the scientific set-up for measurements as well as the behavior and influence of parameters of ventilation according to airflow distribution under consideration of technically possible set-ups of mine fans. This study was done in an underground mine with a flat seam room and pillar mining method.

Feb 27, 2013

By M. Mead, J. Dumouchel, W. Yule, J. Giroux

The QMM mineral sands of South East Madagascar contain approximately 1,900 million tonnes of mineable sand with a total heavy mineral (THM) content of roughly 4.5wt%. The QMM deposits are the world’s largest known reserves of 60% TiO2 ilmenite and also contain a small volume of zircon. The deposits are semi-continuous and homogenous and the mineralized sands are free flowing with minimal overburden, induration & slimes. These characteristics are favourable to dredge mining and allow the application of conventional wet gravity, electrostatic & magnetic separation to final products. A mature THM mineral suite of high valuable heavy minerals (VHM) content has enabled the development of a relatively simple separation process.

Jan 1, 2005

By N. A. Abdel-Khalek

The amenability of carbonate separation from a sedimentary phosphate ore using a bioflotation process was studied. Two types of bacteria were chosen for this study. The experiments were performed using oleic acid as collector. The flotation experiments were carried out using statistical designs for optimizing the main operating parameters. A concentrate containing 0.78% MgO and 30.15% P2O5 with a recovery of 92.31% was obtained from a feed containing about 2.45% MgO and 27% P2O5. These specifications could not be obtained using conventional flotation experiments under similar conditions in the absence of bacteria. Measurements of zeta potential, adsorption of bacteria and collector, as well as froth power, were performed to explain the role of microorganisms in the surface modification of both dolomite and phosphate and in their interaction with the collector.

Jan 1, 2009

By Alan Weakly

The Powder River Basin (PRB) of northeastern Wyoming and south-central Montana is the largest strippable reserve of compliant coal (0.6 or less lb of sulfur per million Btu) in the United States. In mining parlance, it is the Mother Lode! Wyoming’s portion of the Basin provides one fifth of the coal produced in the United States annually, and the state has been the nation’s top coal producer for the past six years. Based on 1993 production statistics and estimated strippable compliance coal reserves, Wyoming may remain the nation’s top producer for the next 76 plus years. Past articles on the PRB have focused mainly on production. After living and working in the Basin for the past five years, I have developed an appreciation for the area and its major industry that transcends size and production data. In the fall of 1993, MINING ENGINEERING’s publisher and I decided to present a series of articles that would cover many other aspects of the Basin. Ten topics were outlined, and specific individuals, selected for their knowledge and experience, were asked to contribute articles about their specialties. Although Montana has four large mines producing coal from the PRB, this series of articles will concentrate on the Wyoming portion of the Basin.

Jan 1, 1994

By G. Hoffman

Sustainable development has brought social, environmental and energy efficiency concerns together with management and governance of natural resources. Cement manufacturing, an energy- and natural resource-intensive industry, is adapting to meet sustainable development goals. Emission standards for cement plants and increasing energy costs have lead to changes in the use of natural resources and recycled materials. Utilizing pozzolans or supplementary cementitious materials (SCMs) as mineral admixtures in blended cement or as a substitute for cement in concrete lowers energy costs and CO2 emissions. Although the western U.S. is rich in natural pozzolans, artificial products, particularly fly ash, have greater use as mineral admixtures. Pozzolans and SCMs have many beneficial properties, such as preventing alkali-silica reactivity, a common problem in the western U.S. Barriers exist for mineral admixtures in the cement and concrete industries because of past inconsistencies in quality or availability. New environmental regulations on the primary industries producing artificial mineral admixtures could adversely affect the quality and quantity of these materials in the future.

Jan 1, 2009

By E. A. Sarver

The Fe(II) regeneration process is an important aspect of Alternate Anode Reaction Technology (AART) for copper electrowinning (EW). In AART, Fe(II) is oxidized to Fe(III) at the anode during EW, and it must be regenerated to maintain recyclable electrolytes. Regeneration is achieved via Fe(III) reduction by SO2(aq), and the reaction is catalyzed by activated carbon particles. To better understand this process, a kinetic model was developed and experimentally validated for the Fe(II) regeneration in the current work. The investigation focused on the primary reaction mechanism and the reaction rate dependence on four variables: carbon particle size, flow rate, initial Fe(III) concentration and initial SO2 concentration. The Fe(II) regeneration reaction is mass-transfer controlled in the presence of activated carbon. Carbon particle size and initial Fe(III) are the most influential factors under the conditions tested. Initial SO2 concentration is insignificant to the reaction rate.

Jan 1, 2007

By Paul C. Schmall, Thomas Tuozzolo, Arthur B. Corwin

The Lenox Avenue Reconstruction Project involved the excavation and replacement of 750 m (2,500 ft) of deteriorated subway invert concrete, 5 to 7 m (15 to20 ft) below water table in very permeable ground. The Replacement work was done over an 8 month period, while maintaining track service through this subway section. The project was dewatered with a single 125 l/s (2,000 gpm) wellpoint system,750 m (2,500 ft) in length, which was installed from inside the active tunnel structure and configured to coexist in the subway tunnel with operating trains as well as the construction activities. A thin diaphragm jet grout wall was utilized on one end of the site to cut off the flow of water across a difficult geological interface that was situated immediately below the tunnel invert. The thin diaphragm jet grout wall permitted the large 116th Street Station area to be dewatered completely with well points from outside of the excavation.

Jan 1, 2001

The status and outlook for mining, in your view. Minerals remain a major part of the world’s economic foundation. The fortunes of the mining industry rise and fall with general economic trends, but mining is no less important today on a global basis than it has been historically. Certainly, portions of the industry are critically depressed — domestic copper to name one area —but other sectors are prospering. Mineral consumption, both worldwide and in the United States, has increased steadily since the Great Depression, hitting all-time highs in 2000, the last year for which I have seen data. The highly developed economy in the United States tends to obscure the continuing importance of minerals here. But in less developed nations the critical nature of minerals is obvious and well accepted. In short, although there is no shortage of problems or challenges facing mining — there never has been — mining remains an essential business with great global opportunity.

Jan 1, 2003

By Dennis Ofiara

Several recent tunnel jobs have required special adaptations of hard rock TBMs. Some of the special job conditions are ?no blast? launch requirements, small shafts or launch pits, proximity to existing underground structures, and short tunnels where the TBM must be retrieved through the primary lining. This paper describes a few of these projects, and the machine adaptations that have made TBM excavation feasible.

Jan 1, 2008

Based on X-ray phase analysis and exploratory experiments, a new technology was developed to recycle multiple valuable elements in spent Al2O3-based catalyst. The experimental results showed that after roasting at 750°C for 30 minutes at an Na2O:Al2O3 mol ratio of 1.2, the leaching recoveries of alumina, vanadium and molybdenum from the spent catalyst were 97.2%, 95.8% and 98.9%, respectively. Vanadium and molybdenum in sodium aluminate solution can be recovered by barium hydroxide and barium aluminate. The precipitation recovery of vanadium and molybdenum was 94.8% and 92.6%, respectively. Al(OH)3 is prepared from sodium aluminate solution using the carbonation decomposition process. The purity of Al2O3 is 99.9% after calcinations, and the recovery of alumina can reach 90.6% in the whole process. The Ni-Co concentrate was leached with sulfuric acid, and a nickel recovery of 98.2% and a cobalt recovery of more than 98.5% were obtained under the experimental condition of 30% (w/w) H2SO4, 80°C, a liquid: solid ratio of 8:1 (by weight), a reaction time of 4 hours and a stirring rate of 800 rpm.

Jan 1, 2007

By D. Rendini, R. D. Gutridge

INTRODUCTION Gwinnett County, Georgia, is a part of the rapidly expanding metropolitan Atlanta Georgia area. Located approximately 48 km (30 miles) northeast of Atlanta, Gwinnett County has a current population in excess of 600,000 and is projected to reach a population of 1,200,000 by 2025. As a part of the County’s master plan to supply drinking water for the expanding population and to increase system reliability, the Gwinnett County Public Utilities Department undertook the Shoal Creek Raw Water Intake and Pump Station Project. Figure 1 shows a vicinity map for the project. Prior to construction of the Shoal Creek Raw Water Intake and Pump Station Project the County had a single raw water intake to feed water from Lake Sidney Lanier (Lake Lanier) into a filter plant for processing into potable water. This project together with a newly constructed water filter plant provides Gwinnett County additional capacity and system redundancy to prevent interruptions to the drinking water supply. Lake Lanier is a man made reservoir with over 800 km (500 miles) of shoreline and was constructed by the Army Corps of Engineers in the 1950s for hydro electric power generation, flood control, and navigation benefits for the Chattahoochee River. Over time, Lake Lanier has become an increasingly important source of drinking water for the metropolitan Atlanta area. This paper focuses on the primary underground construction and lake tap components of the project including a 42.7 m (140 ft) deep pump station shaft 24.4 m(80 ft) in finished diameter transitioning to a 6.1 m (20 ft) finished diameter shaft, a3.05 m (10 ft) finished diameter by 19.8 m (65 ft) deep intake shaft constructed in an average of 21.3 m (70 ft) of water, and a 190.5 m (625 ft) by 3.05 m (10 ft) finished diameter modified horseshoe tunnel connecting the two shafts. This raw water intake system, in conjunction with the incorporated pump station with 8 pumps and dual1,829 mm (72 inch) pipelines, provides a system capacity of 1,091,062 m3/day(240 MGD) to two water filter plants and is expandable by the addition of pumps to1,500,210 m3/day (330 MGD). Parsons provided design and construction management services for the project. The $29.6 million contract to construct the project was awarded to W.L. Hailey &Company. Notice to proceed was given August 6, 2001 and substantial completion was achieved on January 20, 2004. Value engineering changes adopted for the project contributed to completing the project at a final cost of $28.8 million.

Jan 1, 2005

By Cem Şensöğüt, Özer Ören, Yaşar Kasap

The mining sector, which has an important place in terms of raw material and energy supply, is referred as a sector with one of the highest fatal accidents in comparison with other sectors. In this century, where occupational health and safety awareness has increased, it is important to review the past accident statistics and to determine the current deficiencies by using the information in the inventory. In this study, the Malmquist total factor productivity index (MPI) has been utilized to investigate the changes in the work accidents occurring in the Western Lignite Corporation (Turkey), where underground and surface production methods are applied, and to determine the measures to be taken. According to the results obtained, both the decrease in production amount and the increase in the number of accidents caused inefficiencies during the period in concern due to the expected 10-year economic life of the mechanized system operating in the underground production panel that came to an end in 2007 and the flooding took place in early 2017. Compared with the underground operations, it has been determined that production can be carried out at the appropriate scale despite the heavy working conditions encountered due to the changing climatic conditions and the progress of production in the surface operations.

By Louis W. Cope

Mongolia is known in western countries as the location of rich dinosaur fossil fields. However, the country is even richer in mineral resources. The Ministry of Industry and Trade reports 6,000 mineral occurrences of 80 metals and minerals. Mongolia has already attracted much foreign investment in the mining sector. Mining is the country’s largest industry. It is responsible for 17 percent of the gross domestic product, 65 percent of industrial output and 57 percent of export earnings.

Jan 1, 2006

By Ren Xiangwen, Shi Xuefa, Shao Mingjuan, Ye Jun, Yang Yaomin, Li Bing

"The Mid-Atlantic Ridge (MAR), one of the archetypes of slow spreading ocean ridges, extends from the Arctic Mid-Ocean Ridge southward to the Bouvet triple junction making up a significant proportion (~ 40%) of the global oceanic ridge system. During the past few decades, many hydrothermal fields like TAG, Logatchev, Ashasze were discovered along the northern part of the MAR, whereas the southern part, which makes up one third of the ridge (6000km), shows little documentation of hydrothermal mineralization, except for three sites: Site 4°48! the Nibelungen Field, and Lilliput. During March to May 2011, following discovery of three new hydrothermal fields during the 2nd Leg of COMRA's 22 Cruise of the R/V DayangYihao, the 3rd and 4th Legs found another two high temperature hydrothermal fields (SMAR15°S, SMAR26°S), one low temperature field, and several fields with strong turbidity and temperature anomalies in the water column. In this study, we present a preliminarily study of the mineralogy and isotopic geochemistry of the sulfides from SMAR 15°S and SMAR26°S.SMAR 15°S is situated in a SE-NW offset depression of an axial neovolcanic ridge in the median valley, with water depth of about 2793m. In the water column around this field, strong turbidity and temperature anomalies were detected. Ten-meter tall venting chimneys, hydrothermal mounds, as well as a large amount of hydrothermal vent shrimp were also observed and recorded by ROV and deep-tow camera surveys. The samples collected from this field include sulfide chimney fragments, massive sulfides and basaltic rocks. Based on the major metal and the mineral assemblages, three types of sulfides have been identified: 1) Zn-Fe rich sulfides with abundant wurtzite and pyrite zoned fragments, 2) Cu-Fe rich sulfides with much isocubanite and pyrite assemblage, 3) Fe-rich sulfide with massive pyrite fragments. These indicate that this field has undergone at least three phases of mineralization during the venting history."

Sep 1, 2014

By C. A. Young, J. D. Miller

The surface chemistry of the calcite/oleate flotation system was examined by in-situ FT-NIR/IRS. Spectra of combination and overtone bands of aliphatic stretching vibrations revealed gauche/trans conformational changes that occurred solely as a function of temperature. The conformational changes were attributed to the simple "melting" behavior associated with phase transitions. It was concluded that chemisorbed oleate at calcite surfaces is gel-like at temperatures below 22oC, resembles a coagel between 22oC and 31oC, and becomes micelle-like at temperatures above 31oC. By comparison, chemisorbed oleate at fluorite surfaces also undergoes these phase transitions but is additionally dependent on adsorption density. The conformational changes were observed at high chemisorption densities (> 2.0x10-10 mol/cm2) and attributed to molecular forces, primarily van der Waal's interactive forces, among neighboring chemisorbed oleate molecules. Similar analysis of in-situ FT-NIR/IRS spectra of surface-precipitated calcium dioleate at calcite surfaces did not exhibit this behavior thereby confirming that surface-precipitated calcium dioleate remains in an all-trans conformation. The results help explain why surface polymerization is not observed at calcite surfaces but is observed at fluorite surfaces.

Jan 1, 2002

By H. J. Sutherland

This paper reviews the results of the subsidence research prop ram at Sandia National Laboratories. The manuscript highlights the following: the application of empirical methods (profile functions) to the subsidence above longwall panels in the U.S.; the use of the "rubble model" to describe the behavior of broken strata as it distends when it falls to the Mine floor (or top of the rubble pile) and then is subsequently compacted as it is loaded by overlying elements of strata; and, the application of physical modeling techniques (centrifuge simulations) and numerical techniques to study the failure mechanisms in highly structured stratigraphy. The capabilities of the latter two are illustrated ')y comparing their predictions to the results of a field case that has complicated stratigraphy.

Jan 1, 1982

By D. A. Norrgran, J. A. Wernham, D. E. Walsh

A qualitative test program was sponsored jointly by the University of Alaska and Eriez Magnetics, in order to study placer gold nugget recovery using an eddy-current separator. Various gold nuggets from Alaska, ranging from 6.4 mm to 63.5 mm in size, were tested. All testing was performed using an Eriez Laboratory ESC, Model REA, fitted with 2000 gauss, surface field strength magnetic rotor. The belt speed was set to 91 meters per minute and the rotor speed was set to 2500 rpm in the forward direction. The splitter was adjusted to just reject the largest pieces of rock that measured an average 76 mm x102 mm x 127 mm. Based on the results of this limited test work, it can be recommended to placer gold mine operators, that Eriez Magnetics ECS technology is a viable and practical concentration technology for coarse gold recovery. Silver and platinum were also tested.

Jan 1, 2003

By Ashis Bhattacherjee, Rahul Upadhyay, Nearkasen Chau, Aditya Kumar Patra, Dhanjee Kumar Chaudhary

Heavy earth-moving machineries used in open-pit mines intensively expose the drill operators to whole-body vibration and shocks and thus to musculoskeletal disorders. The roles of an individual, machine, and rock-related factors in their exposure remain poorly understood. This cross-sectional study investigated their role among 39 drill operators from Indian iron ore mines. It shows that 70% of the operators were exposed to high levels of vibration, above the limit values recommended by ISO 2631-1. Multiple linear regression models showed that the whole-body vibration and shock exposures were strongly associated with operator’s age, drill machine model, rock’s hardness, uniaxial compressive strength, and density. The role of body mass index was close to significance (p = 0.08). Univariate analyses found that drill’s age, seat pad thickness, and seat backrest height were also strong predictors. These results help in identifying risky operators, materials and occupational situations, and in implementing appropriate prevention and intervention to reduce and monitor the exposures and health risk.

By E. Sun

Tailings disposal is a significant consideration for the mining industry, with the majority of the ore processed in most mining operations ending up as tailings. Several tailings dam failure accidents have occurred during the past few years and mine tailings dam failures are occurring at relatively high rates. Tailings dam failure is disastrous with the serious damage and the loss of lives. To increase the tailings dam safety, a tailings dam monitoring and pre-alarm system (TDMPAS) based on the internet of things and cloud computing platform has been accomplished with the abilities of real-time monitoring of the saturated line, impounded water level, rain fall and the dam deformations etc. The TDMPAS has been applied in several mines in China and helped the mine engineers monitor the tailings dam safety and get warning information automatically and remotely in any kind of weather conditions. This work has been demonstrated the tailings dam monitoring and pre-alarm system (TDMPAS) is meaningful to monitor the tailings dam physical safety condition. The TDMPAS could be applied to monitor all the national tailings dams online in the future.

Jan 1, 2012