Search Documents

By Teja Reddy, Narasimha Mangadoddy, Mandakini Padhi

"In mineral comminution circuits, the feed to hydrocyclone consists of a heterogeneous mixture having varied degrees of liberation and sizes leading to the multi-component particle system. The presence of multicomponent particles exhibits a significant change in the classification performance parameters. In this work, a numerical study is conducted with an artificial mixture of magnetite and silica of different proportions having similar particle size distribution to understand the multicomponent interaction in a laboratory scale hydrocyclone. The heterogeneous feed is injected tangentially would attain different settling rates under the influence of centrifugal, drag and turbulent dispersion forces. In this work, Large Eddy Simulation (LES) is used to resolve the continuous phase turbulence. Modified Algebraic Slip Mixture (ASM) model using the corrected Newtonian rheology of fines to simulate multi-density and multi-size particles of the mixture in a hydrocyclone. The influence of the multi-component particles on classification performance is extracted from the simulation in terms of the performance curve, i.e. recovery to underflow, volume fraction distribution and the key forces acting on each particle in the mixture. An interaction was observed between different components during the classification process, featuring accumulation of heavier particle at wall-side pushing the lighter particles into the inner locus of zero vertical velocity (LZVV) zone. The comparison of separation factors of different size particles presented the higher probability of the magnetite of same size reporting to wall region and hence to underflow. Hence, an increased component cut-size with the increased magnetite proportion, particularly a profound effect on lighter density component’s cut-size was observed. INTRODUCTION The multicomponent existence is found in naturally occurring ores, affecting the pure metal extraction, nonetheless also affects the comminution and classification processes. Among many another classifier, hydrocyclone is a vital equipment used vastly in many industries. The main advantages over other classifiers are a static body, low operating cost and maintenance, high throughput, low floor space requirement etc. A typical hydrocyclone consists of a cylindrical section with a central tube connected to a conical section with a discharge tube. The fluid is injected tangentially into hydrocyclone causes swirling and thus generates centrifugal force within the device. The multiphase interaction inside the hydrocyclone is extremely complex and mostly explained by theories based on hypothesis. In past years, many theoretical models were proposed like a balanced orbital model (Criner, 1950), the residence time model (Reitema, 1961) etc. Though these models give an estimation of the cut-size and other performance parameters, it cannot predict the accurate performance of the actual state of operation. Among these models, the balanced orbital theory is the most adapted concept, based on the force balances of the particle in the dual vortex flow of hydrocyclone. The finer particle is subjected to the inward drag force, generated from the outer vortex flow to the air core, and drags the particle towards the overflow. The larger particle with the higher mass have enhanced centrifugal force and falls into primary vortex near wall reporting to the underflow. Generally, the forces acting on the particle include the drag force, centrifugal force, pressure gradient force, added mass force, Saffman lift force, Magnus force and basset force (Kraipech, 2005). The major forces like a drag, centrifugal, pressure gradient are the function of the particle properties like the size and the density. Hence, the existence of the multi-size and the multi-density particle will affect the separation phenomenon, with the varied forces acting on it. The understanding of the multicomponent classification effect using ores has been only explored in few studi"

Jan 1, 2018

By Jacques Eksteen, Sharif Jahanshahi, Neill J. Bartie, Shouyi Sun

The gradual increase in Cr2O3 levels of UG-2 ores has become a matter of concern for platinum producers in South Africa due to the formation of chromite spinels in melters. The effect of bulk FeOx/MgO ratio, Cr2O3, temperature and oxygen partial pressure on phase stability and composition in the system FeOx-MgO-SiO2-Cr2O3-Al2O3-CaO has been studied between 1400°C and 1600°C using the drop-quench technique. An increase in temperature was found to result in a decrease in [Fe/Cr]spinel. This effect is shown in Figure 1 for the six slag compositions investigated.

Jan 1, 2003

By S. S. Indi, D. Santhiya, S. Subramanian, K. A. Natarajan

The interaction of sphalerite- and galena-adapted Bacillus polymyxa (B. polymyxa) cells with sphalerite and galena has been investigated through adsorption, electrokinetic and flotation studies. The amount of sphalerite-adapted cells adsorbed onto sphalerite and galena is found to decrease with increase in pH. On the other hand, the adsorption density of galena-adapted cells onto galena shows a feeble maximum around pH 8, and the amount adsorbed is marginally higher in the pH range of 8 . 11.5. In the case of sphalerite the amount adsorbed is higher in the pH range of 5 to 7. The adsorption density of both the adapted cells is higher for galena vis-à-vis sphalerite. Electrokinetic studies indicate significant surface chemical changes on the chosen sulphide minerals and the bacterial cells, consequent to microbe-mineral interactions. Selective flotation tests on a synthetic mixture of galena and sphalerite confirm that sphalerite could be preferentially floated from galena, using galena-adapted cells, but not with the sphalerite-adapted cells. The cells adapted to galena assay a higher polysaccharide content and are more hydrophilic, while the sphalerite-adapted cells have a higher protein content and possess greater hydrophobicity. Transmission electron microscopic studies have provided evidence in support of the differences between the cell surface characteristics of sphaleriteand galena-adapted cells. Possible mechanisms of interaction between the minerals and the bacterial cells are discussed.

Jan 1, 2003

By J. W. Ahn

Calcined calcium oxide from limestone is hydrated to manufacture calcium hydroxide, and then precipitated calcium carbonate is synthesized from calcium hydroxide. Precipitated calcium carbonate of various morphologies is obtained by controlled conditions of each step and characteristics of limestone, calcium oxide and calcium hydroxide. Especially characteristics of calcium hydroxide have the most influence on morphology of precipitated calcium carbonate character. In this study, therefore, it is investigated the specific surface area of calcium hydroxide and morphology of precipitated calcium carbonate according to hydration temperature. Calcium hydroxide hydrated at high initial temperature has larger particle size than that hydrated at low initial temperature. And formation yield of aragonite precipitated calcium carbonate has improved by using calcium hydroxide had larger particle size (hydrated at high initial temperature).

Jan 1, 2014

By V. F. Bannikov, A. P. Kozlov

"The purpose of this study was to develop a theoretical and technology framework for designing new combined technologies for processing tailings containing non-ferrous and noble metals using dry separation. The main goals of the study were: identifying the distribution patterns of valuable components in various fractions in dry separation processes; examining the patterns identified for different types of non-ferrous and noble metal tailings; developing a theoretical and technology foundation for the development of innovative technologies for the efficient processing of tailings with minimal process water consumption. To examine the possibility of efficient recovery of valuable components from refractory tailings using dry separation, an experimental laboratory unit was designed and built, composed of novel or modified lab equipment: plasma unit for increasing the magnetic susceptibility of Fe - containing minerals; magnetic separator supporting isodynamic and polygradient fields; pneumatic separator for the dry separation of finely dispersed mineral mixtures; dielectric separator using the resonant frequency of the electric field. The laboratory unit supports various modifications and combinations of the lab equipment. The experimental studies led to the development of a unified process scheme for lab tests of mature and non-ferrous smelter tailings using dry separation methods.INTRODUCTION The huge amount of waste from mining and processing of mineral resources Russia inherited from the extensive use of mineral resources in the Soviet Union and amount of waste continue to grow. Often the content of valuable non - ferrous, rare and noble metals in waste exceeds the balance contents in natural ores of the developed deposits. The availability of a rich scientific reserve for the creation highly effective innovative technologies for waste processing determines the necessity of the acceleration in the resolution of problems of the complex assessment, capitalization and involvement in the processing of technogenic resources in Russia (Chanturiya and Kozlov, 2014.)."

Jan 1, 2018

By James A. Finch, Linda Restrepo, Mitra Mirnezami, Amy Buchanan, Maryam Hashemi

Settling rate studies on slurries from Cu/Zn flotation plants occasionally reveals two aggregation maxima at pH 8-10 and 10-12 (Figure 1). From measurements on sphalerite and silica suspensions the double maxima could be replicated. These maxima correspond to the effects of Zn and Mg ions. The aggregation mechanism of both ions is related to the formation of the corresponding hydroxide precipitate. A combination of chemical and electrostatic bridging by the hydroxides is considered to be the aggregation mechanism.

Jan 1, 2003

By A. V. Golovanov, A. V. Mihailova

"NPO RIVS employs complex approach to engineering and design of the new facilities in close cooperation of Mining, Research, Hydrometallurgy, Design, Construction, Power Supply, Automation, Production and other departments. General Design Contractor (and then General Contractor) is directly involved in geological exploration, engineering surveys, floatability studies, feasibility study of process solutions and construction options. It delivers greenfield project and guarantee its efficient performance in future. Shiralgin is a small gold and copper deposit, gold average grade is 4.7 g/t. RIVS departments have studied ore floatability, developed process procedures for design and performed pilot testing. Construction of integrated plant including ore crushing and grinding, flotation and hydrometallurgy units with Dore gold production of 5 000 thousand tons ore per year (66.7 t/h) is recognized as economically viable. The technology used of separate dry stockpiling of flotation tailings and cyanidation tailings. Water circuit for concentration and hydrometallurgy is separated, too. Process design was performed based on BIM software like Autodesk Revit, Civil 3D, Rocscience slide using process procedures developed by RIVS Research units. Engineers provided modeling of primary crushing unit, coarse ore storage, main building (including grinding, flotation, thickening, filtration, loading, hydrometallurgy), tailings thickening unit, building for reagent storage and conditioning, tailings pond for dry stockpiling of flotation tailings and cyanidation tailings, sedimentation ponds, laboratories, infrastructure including Administration building and camp. Payback period is 3.5 years. 3D model of facility is currently stored at the State Agency of Geology and Mineral Resources affiliated to the Government of the Kyrgyz Republic.INTRODUCTION The Kyrgyz Republic has substantial potential of mineral resources including gold ores. Mining industry actively develops and involves international investors. Inventory includes 42 deposits (Figure 1) that have reserves of 616.4 t [1] of gold. The Kyrgyz Republic takes the third place in gold mining among CIS countries after Russia and Uzbekistan by producing up to 20 t annually."

Jan 1, 2018

By N. A. Dementyeva

To improve gold recovery from preg-robbing carbonaceous ores a technology including gravity, flotation, recleaning of the flotation concentrate, intensive cyanidation of the gravity concentrate and carbon-in-leach (CIL) process for intensive cyanidation tailings and the recleaned concentrate was developed. The final flotation tailings are shipped to tailings disposal. Total gold recovery by the proposed technology from the ore with the head grade of 0.8 g/t was 83.9%. The gold loading onto the activated carbon from CIL process was 6.5 g/kg.

Jan 1, 2014

By S. Leroy

Grinding is the most energy consuming step in mineral processing, however, it is still poorly understood and its efficiency is difficult to monitor. Mill performances are traditionally measured at the mill discharge, on the basis of a mass percentage passing a certain sieve. This approach does not reflect what happens to the fines through milling. On another hand, if many macroscopic parameters, such as the percent solids of the pulp, its viscosity, or its mean residence time in the mill are known to be related to grinding efficiency, the link between these parameters and particle size distribution (PSD) is still unclear. Here, a methodology is established to understand the effect of ball mill operating conditions on particle size and shape distribution in the grinding process. The study focuses on the particular case of an Upper Group 2 (UG-2) platinum ore concentrator. Due to the very low grade of sulphide and PGM (Platinum group metals) in UG-2, grinding mechanisms are entirely control by gangue minerals. These two minerals have contrasted properties and PGM content and these properties immediately affect the entire recovery process. So, the grinding of both gangue minerals is studied on a size by size basis. At particle scale, three parameters are addressed: particle size, particle composition and particle shape. The specific behavior of chromite and silicate grains is demonstrated. As a conclusion, this study gives some clues to operate ball mills in a more efficient manner regarding chromite issue in the processing of UG-2. Keywords: ball milling control, UG-2, chromite, fine particle, particle shape, segregation

Sep 1, 2012

By I. Kairyakov

The present paper is about the restoration of the molybdenum production in the floatation plant of Ellatzite-Med AD in Bulgaria. The process, based on a working design, includes the construction of a new floatation molybdenum section in the existing molybdenum department of the Floatation Plant using the so called Vemco inert-gas floatation machines, made especially for the molybdenum floatation. While in the ordinary floatation machines, block impellers create suspension of the air, sucked from the atmosphere with the slime particles of the concentrate, which creates conditions for oxidizing the reagent, Vemco inert-gas floatation machines are covered with hermetic lids and the air inside the chamber is used. The technology, suggested by Geotechkoper Ltd. for making the working project, employs special machines from Dor Olliver Aimco, suitable specifically for molybdenum floatation in order to reduce the oxidizing of the reagent sodium hydrosulphate. Also the transport of the chamber product is done in hermetic conditions as the molybdenum flotation is done in two floatation rows and refining operations 3 to 8 are placed in the second row. Thus in the basic molybdenum floatation together with the first and second refining operations, which are hermetically closed, an ambient condition with low content of oxygen is created, that is about 8% for oxygen and about 92% of nitrogen, in which the oxidizing process is extremely reduced. This in turn results in reducing the consumption of the reagent depressor ? sodium hydrosulphate. In that way there is an improvement of the economical indices of the molybdenum production.

Jan 1, 2014

By S. Gaydardzhiev

Initial experiments towards preparation of hollow ceramic microtubes by dip-coating of fibrous plants with water based alumina gel-casting slurries using hemp and coconut fibres as templates have been done. It has been found that the wettability of fibres and accordingly the stability of the developed ceramic layer on their surface during slurry gelation varied significantly within the different fibre types. Good correlation between the diameters of the template fibres and the resulting channels has been found at the level of solids loadings used, 31 %. Hemp fibres used as bundles have led to formation of multi channel patterns while the coconut fibres-templated process resulted in uniform monochannel materials. The micro tubes have show good mechanical handling.

Jan 1, 2014

By V. Y. Dementyev

Laboratory and pilot-plant testing using a sample of gold-bearing semi-oxidized ore from a Russian deposit followed by a flow sheet and reagent flotation mode development to design a plant was carried out in IRGIREDMET in 2009-2010. According to the developed flow sheet low alkaline flotation conditions are recommended in order to activate the surface of sulfides. The pH lowering from natural (7.5-8.0) to optimal (4.6-4.8) value using sulfuric acid provides for an increase in gold recovery. Before CIL, a final flotation concentrate is pretreated using pressure oxidation. It was found that the use of recycled solutions from pressure liberation in order to create acidic conditions for flotation instead of sulfuric acid during pilot-plant testing is recommended. The flow sheet offers the detoxification of remaining pressure oxidation solutions together with the flotation tailings. The carbonates presented in the tailings significantly reduce the consumption of lime for detoxification and allows for the use of two tailings dams instead of three. The first is used for the tailings of flotation and pressure oxidation recycled solutions, which were detoxified together. The second tailings dam is used for detoxified cyanidation cakes of the flotation concentrate. It was found during pilot-plant testing that flotation under natural and acidic conditions provides for 88.9 percent and 93 percent gold recovery, respectively. 4.1Au percent increase recovery was achieved due to the reduction of gold losses with flotation tailings and better quality of concentrates.

Sep 1, 2012

By S. Kondratiev

Mechanism of the action of nonpolar physically adsorbed reactants in froth flotation is under discussion in the paper. It is shown that their basic influence on flotation includes removing of the kinetics restrictions of the flotation complex formation. Experimental data and practical evidence reported in the paper sustain the proposed mechanism. There are discussed potential dependence of the kinetics of dixanthogen formation on platinum and its influence on the induction time (IT).

Sep 1, 2012

By Gerke Gilian, Pretz Thomas, Pehlken Alexandra

"The evaluation of health hazards within the treatment of mineral and waste materials is gaining more and more importance in industrial countries. The need to control occupational health and safety has been recognised, and regulations which describe general protective measurements for personnel provide a tool to protect their health. It is the aim of the paper to give an outlook for practical approaches to risk assessment and to present measures for exposure reduction in accordance with the state of the art in Germany.Both the treatment of minerals and of waste materials are described in relation to the risk assessment. The method of evaluating health hazards in the two industries is similar and therefore both examples are presented next to each other.The example presented in the paper is the German “Biostoffverordnung” (the regulation for biological materials) which is important for the waste treatment industry. All kinds of waste treatment facilities (like composting facilities, waste dumps, sorting facilities for packaging materials) are obliged to carry out an assessment of health hazards for a variety of working areas and working places. The possible safety requirements deriving from this regulation are presented and discussed under the aspect of biological hazards."

Jan 1, 2003

By Sergey Dyachenko

"Following the adopted strategy for making the production modern, efficient and environmental friendly the Company completed a stage of the integrated program aimed at reconfiguration of its processing capacity.Upgrade of the Talnakh Concentrator with commissioning of two start-up facilities (SF) allowed an increase of 30% in its ore processing capacity up to 10 mtpa. In addition to a new high-tech equipment installed, a new concentration process was adopted offering the main advantage of 25-30% reduction of sulfides in concentrate. New concentration technology enabled the total amount of produced nickel concentrates (from Norilsk and Talnakh Concentrators) to be processed at upgraded smelting facilities of Nadezhda Metallurgical Plant and allowed decommissioning of smelting capacities of Nickel Plant resulting in emissions reduction by 30%.Nornickel plans to boost the capacity of Talnakh Concentrator to 18 mtpa by 2022, after commissioning of the 3rd SF. This will provide a shorter route for ores transportation from Talnakh mines along with improvement of cost/performance ratio of ore processing through the usage of the modern equipment and optimized concentration flow scheme. Total capacity of Talnakh Concentrator will be sufficient to process ores from Talnakh deposits with planned upstream assets development taken into account. Volume of ore mined from Norilsk deposits to be processed at Norilsk Concentrator will be also increased.Upgrading the crushing section at Kola MMC Concentrator in 2015 provided finer particles of the crushed ore, resulting in 6.6% increase in specific capacity of ore mills as well as 1% higher recovery of non-ferrous metals due to improved liberation of ore minerals.In 2015-2017 the Company was actively engaged in optimization of existing process flow schemes and parameters of Kola MMC, new high-performance reagents were adopted for concentration process, namely, collectors, depressors, flocculants. These measures allowed the Concentrator to reduce its annual operating unit costs and ensure sustainable production of concentrate with the lower grade of the incoming feedstock.Launched in October 2017, Bystrinsky GOK’s Concentrator was 3D designed and received a range of advanced technological solutions.All design process procedures and technologies rolled-out at the Company’s concentrators were developed by Russian R&D institutes, with the key role of Gipronickel Institute, R&D Service of Kola MMC and Polar Division's in-house Engineering Support Centre."

Jan 1, 2018

By James A. Finch

"Developed countries are in the midst of re-structuring education in minerals-related disciplines as raw materials, once vital to wealth generation, contribute progressively less to the economy. The changing circumstances mean institutions must justify mineral processing by new criteria. After considering what a mineral processor needs to know the ways to deliver are considered. Taking twenty graduates per year to illustrate, one institute could justify this number as a program in a department or school (of whatever grouping of disciplines). A strong research component would make the package additionally attractive. Divide among four institutions and mineral processing is best served in a research centre with delivery taking advantage of multi-centre and distance learning opportunities.INTRODUCTIONThis is one of five plenary lectures at the Congress. I may have preferred a technical subject, as that is what occupies most of my thinking hours, but it is reasonable as an academic that this topic should come to one of us. The fact the topic has not been high on my agenda may provide one advantage: that I can suggest directions free of pre-conceived notions, just as when reviewing the background to a technical article the temptation to select in support of one?s interpretations is resisted. The trick will be to add something new.One reading of the title seems to query whether mineral processing education has a future. (I will refrain at this juncture from defining mineral processing and assume for now we share an understanding of the term.) The proximity of natural and human resources led to the Industrial Revolution and the interaction continues to stimulate and sustain industrial and economic development in many parts of the world. The search for raw materials has historically played a key role in opening frontier areas, with undersea and outer space next. The reason is obvious: raw materials along with food and energy underpin society. Thus mining will remain part of human activity along with the need to pass on the knowledge and skills.What happens over time is resource relocation. Raw materials become exhausted in one area to be replaced by sources elsewhere; the demand for some materials lessens while growing for others. Educational institutions can find themselves with the wrong geography or with staff focussing on the wrong subjects. When this happens the restructuring produces much discussion. This is where we are in parts of the world. Japan, Western Europe and the United States are the prominent examples (Dowd, 1998; Flemings and Suresh, 2001; McDivitt, 2002). Mineral processing is becoming a series of courses in related disciplines: resource engineering, environment engineering or materials engineering. The start of the transition is evident in Canada and Australia, perhaps earlier than expected given the contribution of raw materials to their economies. A common backdrop in the developed countries is social pressure to reduce the impact of the ?untidy? aspects of life, and that includes mining. (This is not new: in classical times the mine face was the preserve of slaves and convicts.) These values are exportable, potentially affecting recruitment into mining schools everywhere."

Jan 1, 2003

By Dominic Howarth, Diana Drinkwater, Don McKee

"The pressures on mining and minerals education at the tertiary level are well known. Within Australia, for example, the number of undergraduate mining engineering courses with 30 or more students in each year has reduced to three (University of Queensland, University of New South Wales and Curtin University). Similar declines in both student numbers and participating institutions are evident in many other parts of the world, and notably in USA and most countries in Europe.An in depth study of the Australian sector was conducted in 1997/1998, resulting in the Back from the Brink report (Carter 1998). The Australian situation was summarised as follows.Australia’s minerals education system, in its current form, is fragile and is in no position to seize the opportunity (i.e. world leadership in minerals education) and is more likely to succumb to the threat.Current trends include:- an acute shortage of talented academic staff, as a result of University remuneration packages having become hopelessly uncompetitive with those in the minerals industry;- small student populations and high relative costs, making mineral specific courses vulnerable to closures, when Universities are under extreme cost pressures; this situation will be exacerbated if enrolments drop in response to, say, a cyclical down turn in the industry; and- under-resourcing of minerals departments because of their comparatively small size, making these departments incapable of delivering top class teaching in all aspects of their courses, despite being excellent in some areas.Most of the Australian issues identified above have direct parallels in other countries.The most common response of institutions to the threats is to seek strength, and in some cases survival, through various forms of linkages and networks. A number of these associations, which are frequently defensive in nature, are outlined in the paper."

Jan 1, 2003

By Zhaohui Qiu, Yaguan Ji, Hong Zhong, Qingxia Liu, Yada Liu

"Water is a necessary process medium in mineral processing. For the operations where fresh water is not available, sea water could be used as an alternative processing medium to replace the fresh water if we would have built a solid understanding of the interfacial science and flotation chemistry of sulfide minerals in sea water. In this research, micro flotation of chalcopyrite and pyrite in deionized water and sea water were investigated. For chalcopyrite, the recovery starts to drop from pH 10 in deionized water and from pH 9 in sea water, and the flotation recovery close to 100% before it drops. We can found from the results that chalcopyrite flotation is depressed much at pH 11 in sea water when much white precipitate is found. For pyrite, the flotaion recovery changs a lot in deionized water with 1*10-5 M potasium amyl xanthate (PAX) as collector. It’s relatively high at pH 8~10 compared with that at pH<8 and pH>10. While in sea water, the trend is almost the same as that of chalcopyrite. Zeta potential measurements and chemical equilibrium calculation were used to find out that magnesium hydroxide species coats on the surfaces at high pH in sea water are the main reason for depressing the chalcopyrite and pyrite flotation. Through understanding the interfacial science and the solution chemistry of sea water and its impact on processing efficiency, this research will not only helps reduce the use of fresh water to minimize the disposal of spent water for environment protection, but also enhance the recovery of valuable minerals in froth flotation."

Jan 1, 2014

By C. Abbruzzese, F. Vegliò, S. Ubaldini, R. Massidda

The aim of this paper was to study the influence of different water/organic solvent mixtures (isopropyl alcohol, ethanol and ethylene glycol) on the gold desorption process. The experimental work was carried out on laboratory scale, using activated coconut carbon with different temperatures and extraction times, without adding cyanide. Best results have been obtained in this order: isopropyl alcohol > ethylene glycol > ethanol. Starting from gold concentration of about 5 g Au per kg of carbon, best kinetics resulted in 97-100% of gold extraction, after 8 hours of desorption, at a temperature of 80ºC.

Jan 1, 2003

The Indian steel industry is growing at a rapid pace and expected to be the 2nd largest steel producer in the world after China. To cope up with this growth and to sustain it, the industry needs to focus on effective utilization of domestic metallurgical coals. While the importance of indigenous coal has increased, its supply from the domestic sources is declining. This is primarily due to high ash content in Indian coals leading to its difficulty in washing to a low level competitive to imported coals. Non-availability of a suitable beneficiation technology to bring down the ash to such a low level is the other reason. Effective utilization of current technologies has enabled Tata Steel to bring down the ash to 13-16% from its captive collieries. However, further lowering the ash using the conventional beneficiation technologies is difficult and unsustainable. New technologies should be developed for bringing down the ash further. A thrust area research program has been undertaken at Tata Steel for producing clean coal with 8% ash maintaining the yield currently achieved in its washeries. The technologies attempted are based on chemical beneficiation of coal. In leaching process, suitable chemicals are used for extracting ash minerals from the coal. As an alternative process, the combustible part of the coal is being extracted using a suitable organic solvent through an organo-refining process. Both the processes have been successfully developed in the laboratory and are being demonstrated in pilot scales. Various beneficiation processes practiced at Tata Steel including the efforts made for developing new processes for achieving clean coal with 8% ash have been discussed in this paper. Keywords: metallurgical coals, washing, beneficiation technologies, chemical beneficiation, leaching, solvent, and organo-refining process

Sep 1, 2012