Search Documents

By F. -Z. Ji, A. G. Irons, M. Barati, K. Coley

In order to optimize carbon injection into oxidizing slags, in terms of carbon and iron yield, we must have a detailed understanding of the kinetics of the reactions involved. The current study measures the rate of carbon oxidation during injection at steelmaking temperature by means of injections of coal into EAF slags. The compositions of analysed outgoing gas were used to calculate gas flow rate and hence the gasification rate of carbon. A fundamental equation to predict residual carbon in slags was developed. The predictions using this model at moderate injection rates are in good agreement with experimental data. The reaction rate of EAF slag with carbon is under mixed control by the slag gas and the gas carbon reactions. The relative importance of each step depends mainly on the v-ratio of slags. A relative reactivity parameter ? has been defined and it is found to be important to carbon-slag reaction kinetics and slag foaming. Key words: carbon-slag reaction, kinetics, slag foaming.

Jan 1, 2004

By Carroll Forbes

INTRODUCTION MANY different shapes of drill bits are in use with hammer drills, but little definite information is available whereby to judge which one of these shapes is the best. The following investigation was undertaken in order to determine what effect, if any, the shape of the cutting edge has on the cutting speed and wearing qualities of drill bits. The bits tested were those in common use, namely, the 4-point or cross bit, the 6-point bit, the Z bit and the "Carr" bit. The rock in which the tests were made was the red granite from southeast Missouri. It is a coarse crystalline granite containing an unusually large amount of quartz and is extremely hard, and on account of its uniform texture is admirably adapted to this work. While tests in other rocks might show somewhat different results, nevertheless it is the opinion of the authors that the relative cutting quality inherent in the shape of the bits would be the same in all rocks. Other qualities, such as mudding freely, freedom from fitchering, etc., might make one bit more desirable than another in softer rocks. DESCRIPTION OF BITS TESTED The 4-point bits were the usual shaped bits commonly made on the Leyner sharpener with 14° taper on the wings and a 90° angle between cutting edges. Some tests were run at 85 lb. pressure with a 4-point bit made with a 5° taper on the wings. This was made by using the Carr bit die. The 6-point bits were the usual shaped hits made on, the Leyner sharpener. The Carr bits were made with a 5° taper and an angle of 100° between cutting edges.

Jan 8, 1917

In the Broken Hill South mine tile practice of issuing to the miner a quantity of fuse and a box of caps from which he made up the "rods" required for a particular blast, has been abandoned. Instead, capping stations have been established, and the miner can now obtain, from the magazines, fuses cut to accurate lengths with the detonators attached.Various types of fuse-cutting machines and crimping devices are available, but only those used by the Broken Hill South Mine Ltd. are described in this paper.The fuse-cutting machine, designed by the engineering staff, is an electrically driven unit fitted with a gear box for the purpose of adjusting the rate at which the fuse is fed to the cutting device, thereby enabling fuses of various lengths to be accurately severed from the main coil of fuse.The machine in question is designed to cut 4, 6, and 8-ft. fuses, but no difficulty should be experienced in designing a machine to cut fuses to any required lengths.

Jan 1, 1932

By B. B. Broms

The high transverse tensile stresses that develop in precast concrete piles during driving have been investigated experimentally from pile load tests and theoretically using the finite element method (FEM). These tensile stresses can be high enough to cause longitudinal splitting of the piles just below the pile cap. Test data and FEM indicated that the maximum transverse tensile stress will increase with increasing thickness of the cover. The maximum tensile stress can be high especially if the pile is eccentrically loaded. The results from the experimental investigation and from FEM are described in the paper as well as a simplified method based on the stress distribution in a concrete cylinder at an indirect tension test.

Jan 1, 2010

By F. A. Camisani-Calzolari

The latter half of the 20th century has seen the proliferation of a series of codes to address commodity needs which were brought about by rapidly advancing technologies and the globalization of markets and consumerism. This paper addresses the specific needs and the origin of this surge and presents these codes in the context in which they were developed. It also compares the main codes or groups of codes and elaborates upon their strengths and weaknesses. Three main categories of codes are identified, namely codes for reporting to international agencies, codes addressing government needs and, finally, codes for the investors and the stock market. Codes governed by international agencies usually relate to strategic commodities which have highly specialized fields of usage such as nuclear power generation where international cooperationis eventually the only viable approach for both the development of technologies and their applications. Codes for reporting to governments address the necessity of each state to exploit its mineral potential profitably and to secure the preservation of wealth for future generations. Reporting to investors is experiencing a considerable popularity as of late because of globalization in mining and the growing need for outside financing of mining projects, whose capital requirements are getting out of reach for the average mid-cap mining company. All these codes have advantages and shortcomings dictated by the specific circumstances under which they were developed, therefore necessitating the definition and implementation of some kind of international standard whereby investments and the spread of information across political boundaries would be facilitated. Though none of these codes might ever become international in the true sense of the word because of significantly different legislations at national level, a step that would greatly contribute to the cross-border disclosure of information would be the reciprocal recognition of competent persons by the major mining countries, including China and Russia. It is also becoming essential that financial institutions and investors be properly advised on mining projects by reporting reserves and resources in a transparent and responsible way with the relevant public disclosures being compiled by professionals who take full responsibility for their submissions. Keywords: reporting codes, mineral resources, mineral reserves, competent person, UN Framework Classification, IAEA classification, JORC Code, SAMREC Code and CRIRSCO.

Jan 1, 2004

By Mohammad Djavid

The one-pass tunneling pipe jacking method has often been the most schedule and cost efficient method for the pipe line installation. The main challenges in jacking pipes larger than 108 inches and for longer runs are: transportation and logistics, requiring high jacking forces, keeping line and grades, control of ground surface settlement, providing adequate external lubrication, and the potential of damaging the joints and pipe spigots. In recent years, 144" diameter pipes have been jacked for short runs of up to only 300 feet. In this article design and construction of installation of up to 1,000 linear feet run of 144-inch internal diameter, reinforced concrete pipes without intermediate jacking station in Chicago O?Hare International Airport are discussed. The article also presents discussions regarding the subsurface saturated silt formation, shallow cover, dewatering, jacking and receiving shafts, jacking forces, lubrication and settlement data.

Jan 1, 2008

By D. Komljenovic, J. Paraszczak

"This paper presents the use of queuing theory in truck fleet sizing in open pit mining operations. In the first part, a methodology is developed by which an optimal ratio between the size of shovels and trucks may be determined. The second part gives the fundamentals of the queuing theory and its application in analyzing shovel and trucks. The stochastic character of involved times (loading, truck cycle, etc.) is taken into consideration. Using the above theory, the optimal truck fleet size in actual conditions may be estimated. Minimal operating cost of the working system (shovelstrucks) represents the basic requirement of the analyzed process. The methodology was validated on Caterpillar front-shovel – truck combinations. IntroductionLes camions représentent probablement les équipements les plus utilisés pour le transport dans les mines. Le coût de transport peut parfois atteindre 50 % du coût d’exploitation et 25 % du coût total (Collins, 1996; Kennedy, 1990). Il est critique pour une opération minière de le minimiser. C’est un sujet qui a été traité relativement souvent dans la littérature spécialisée. Les premières applications informatiques dans l’industrie minière ont été développées pour la détermination du temps de cycle des camions.Au fil des ans, la capacité des camions a augmenté et, aujourd’hui, les plus gros manufacturiers de camions (Caterpillar, Orenstein & Koppel, Euclid, Terex, Unit Rig, Komatsu, Liebherr, Belaz) fabriquent des camions ayant une capacité de 200 t et plus dont quelques-uns d’une capacité supérieure à 320 t. Pour les plus gros camions, le coût d’opération peut même dépasser 240 $US/heure dans des conditions modérées (Caterpillar, 1999). Les mines modernes de grande taille peuvent posséder plusieurs dizaines de camions dans leur flotte."

Jan 1, 2004

By Kazem Oraee

In underground coal mining, particularly room-and-pillar methods, the coal pillars play a significant role in roof stability. If the pillar dimensions are increased, the pillar bearing capacity also increases, but more coal remains in the pillar and therefore the recovery of mining operation decreases. Therefore, determining the optimum pillar dimension based on technical, economical and performance parameters is important. In this paper, the coal pillar is designed by using the concept of ground reaction curve (GRC). For this purpose, the GRC for coal pillars is drawn and then the elastic and plastic zone of coal pillar behavior is determined. Based on elastic and plastic zone, different equations are presented to draw a pillar reaction curve and the process of coal pillar design based on GRC is explained. As a case study, this new technique is applied to study the coal pillar state in Tabas coal mine of Iran. The results show that the presented new approach is successfully used in the design of the optimum coal pillar dimensions, and also determines the elastic and plastic behavior limit, which is important especially for the logical design of yield pillars.

Jan 1, 2009

By F. H. Abd EL-Rahiem

A selective dispersion process is presented and the work carried out to find optimum process conditions to minimise the colouring material in ground calcium carbonate (GCC) is described. The feed material is the overflow product from a hydrocyclone which results from using a Denver Attritioning machine with semi-autogenous grinding for one hour and a 1:1 ore/water ratio. By using sodium silicate (SS), with pH 9 and pulp density 5%, the iron content (as colouring impurities) is decreased from 0.21% in the original concentrate to 0.12% in the final concentrate. The degree of whiteness reached is improved to 85% from 63% in the original material. However, by using hexametaphosphate (SHMP) at pH 10 at the same pulp density, the iron content decreased to about 0.073% and hence the whiteness degree increased to about 96%.

Jan 1, 2004

By P. W. Godbehere, B. W. Brooks

"This paper deals with the milling of slags from the Noranda Continuous Process, in the Horne Concentrator at Noranda, Quebec. The milling of copper slags, although novel in Canada, has been practiced in Japan, Finland and elsewhere for several years.In March 1973, the prototype Noranda Continuous Process furnace or ""reactor'' came on-stream, In this pyrometallurgical process (see Fig. 1), copper concentrates mixed with flux are smelted in a single furnace to form copper or a high grade copper matte, and slag. The conventional smelting processes of roasting, reverberatory smelting and converting have been incorporated in a single 17 ft. diameter by 70 ft. long steel cylindrical vessel (l, 2). The copper or matte is tapped from the bottom of the reactor into ladles and transferred to an anode furnace or to a converter. The slag is tapped into 40 ton capacity ladles, cooled, crushed, and conveyed to the concentrator. At the present time, the reactor is operated to produce matte. The matte slag* containing 4 - 6 per cent copper is milled using conventional ore dressing grinding and flotation equipment. A flotation concentrate assaying 35 - 40 per cent copper is recycled to the reactor. Crushing, conveying, grinding, flotation and tailing disposal equipment previously used for over 40 years for ore treatment has been modified to suit the requirements of slag milling. Slag milling is essentially the scavenger circuit of a pyrometallurgical process."

Jan 1, 1977

By D. Komljenovic

This paper presents the use of queuing theory in truck fleet sizing in open pit mining operations. In the first part, a methodology is developed by which an optimal ratio between the size of shovels and trucks may be determined. The second part gives the fundamentals of the queuing theory and its application in analyzing shovel and trucks. The stochastic character of involved times (loading, truck cycle, etc.) is taken into consideration. Using the above theory, the optimal truck fleet size in actual conditions may be estimated. Minimal operating cost of the working system (shovels-trucks) represents the basic requirement of the analyzed process. The methodology was validated on Caterpillar front-shovel ? truck combinations.

Sep 1, 2004

By I. H. Van Horn

IN the development of the incandescent electric lamp one aim of the investigators has been to establish the fundamentals of lamp design, so that the performance of any new lamp may be accurately predicted. The study of the temperature relations in lamps has done much toward establishing these fundamentals. Fig. 1 gives the typical FIG. 1.-ARRANGEMENT OF PARTS IN MAZDA B AND MAZDA C LAMPS. arrangement of the lamp parts in both the Mazda B (vacuum) and Mazda C (gas-filled) lamps. The outstanding differences are the filament form and the bulb shape. The ideal lamp is one in which the filament operates at a uniform temperature throughout its length. In practice, it is necessary to disturb this uniformity by the introduction of supports and terminals. The amount of cooling at the supports and terminals affects the over-all efficiency of the filament as a light producer. The life of the lamp is ordinarily proportional to the maximum and not to the average filament temperature. The Holborn-Kurlbaum type of optical pyrometer has

Jan 9, 1919

By Christoph Mueller, Grzegorz Tabak

Basing on five years of experience, this paper discusses modern e-drive systems used in underground transport. This covers Energy distribution and cabling principles, inverters and motors as well as auxiliary aggregates. Also an overview of different regimes for battery charging and the energy management and the method of control of the traction are lined out: This means that throttle and brake are not handled separately, but integrated into “longitudinal control” algorithms which assure that a commanded speed is maintained while synchronizing the multi motor systems and taking into account the constraints imposed by e.g. slope grade and battery parameters.

Jun 25, 2023

By Michael W. Oakland

Deer Island is the site of the Massachusetts Water Resources Authority (MWRA) wastewater treatment plant which, when completed in 1999, will serve 43 cities and towns in central eastern Massachusetts. Deer Island is located in the Boston Harbor, as shown on Figure 1. The existing wastewater treatment plant on Deer Island is being upgraded to include secondary treatment to comply with Federal require­ments. The new treatment facilities will process an average of 455 million gallons of sewage per day; total capacity will be about one billion gallons per day. The new treatment facilities will cover virtually the entire island. [ ]

Jan 1, 1994

In order to reach a large, untapped reserve of high-quality coal, D8 Cloverlick mine proposed to mine a corridor nearly 2,000 ft deep beneath the Benham Spur of Black Mountain, Kentucky’s highest peak. D8 Cloverlick mine was extracting the Owl seam, but the corridor’s route lay approximately 70 ft above century-old mine workings in the C–(Darby) seam. Adding to the concern, three serious coal bursts had recently occurred in nearby Owl seam workings.

Jan 7, 2020

By Jay C. Hanson

Various electrical and electromagnetic (EM) geophysical techniques are currently being evaluated by the U.S. Bureau of Mines for their effectiveness in the detection and monitoring of electrically conductive (1 to 5 S/m) lixiviant (leach solution) to depths of 600 m, either above or below the water table. These techniques include magnetotellurics (MT) , controlled source audiofrequency magnetotellurics (CSAMT), resistivity and focused resistivity, ground-penetrating radar (GPR), frequency-domain electromagnetics (FEM), and time-domain electromagnetics (TEM). Of these techniques, TEM may be the most effective, but CSAMT and focused resistivity also hold promise. Geophysical computer modeling of the borehole TEM technique was conducted based on an idealized geoelectric section (layered earth) with characteristics based on the Santa Cruz porphyry copper deposit near Cas a Grande, AZ. Layer resistivities and thicknesses were obtained from geophysical data and geologic logs available from the site. Modeling of borehole TEM in both preleach and during leach situations was conducted. Simulating the TEM method using computer modeling proved to be encouraging since there were substantial differences between leached and nonleached responses. The modeling does not prove the effectiveness of TEM in the field, but does indicate that detection of deep lixiviant zones is theoretically possible.

Jan 1, 1992

By R. Stefanko

This first Annual Report covers the work on Contract No. H0377043 "Cable for Face Equipment", from August 1, 1977 to July 31, 1978. It reports the progress in the three areas of over-and short-circuit protection, cable ampacity research and cable couplers. Field trips have established many interesting facts related to circuit breaker settings and cable size. For example, the determination of cable sizes depends on the RMS duty cycle current determined by a particular piece of equipment, but the actual selection of the cable to be used is often a function of the maximum allowable circuit breaker instantaneous settings as specified in Title 30. In order to avoid nuisance tripping as a result of instantaneous starting current field, laboratory and analytical studies are being conducted to determine proper settings and cable sizes Also an extensive program has been established to monitor the performance of high voltage cable couplers and determine their modes of failure. Various equipments are being designed for laboratory testing, and an extensive reeled cable experiment is also under way.

Jan 1, 1978

The Bureau of Mines conducted large-scale laboratory copper ore leaching tests to enable improving copper recovery from large dump-leaching operations. This was done by comparing leaching progress when copper was recovered from recycled leach liquor either by cementation or by solvent extraction. Copper was leached from 7-ton ore samples at room temperature using pH 2 ferric sulfate solutions. With are samples containing 11 percent minus 0.5-inch fines, no marked advantage in using either of the copper recovery methods was evident after 416 days of leaching. With ore containing 32 percent minus 0.5-inch fines, solvent extraction of copper was advantageous in that 60 percent of the copper was extracted after 568 days, whereas only 48 percent of the copper was extracted when cementation was used. Less acid was consumed during leaching when solvent extraction, rather than cementation, was used for copper recovery. Iron, contributed by cementation with scrap iron, plugged the ore bed containing 32 percent fines.

Jan 1, 1981

Stress induced, gravity-assisted failure processes typically dominate long before stress levels approach the strength of the intact rock (at approximately smax > 0.4UCS where smax = 3s1 ? s3 and UCS is the Unconfined Compressive Strength of the intact rock (Martin et al. 1999)). Under these conditions, discontinuities typically become clamped and the failure process becomes brittle. This brittle failure process is dominated by new stress induced fractures growing subparallel to the excavation boundary. While it is possible to identify areas with the potential for brittle failure, for example, using the general assumption that brittle failure will occur in areas at right angles to the major principal stress (Hoek et al., 1995), when the threshold smax > 0.4UCS is reached in areas around the tunnel boundary, or elastic modelling and the Hoek-Brown brittle parameters proposed by Martin et al., (1999) (i.e. m? 0 and s ? 0.11), amongst others, recent observations discussed by Everitt & Lajtai (2004), and Kaiser (2005; 2006) suggest that brittle failure processes are enhanced when structural features such as joints, weakness zones, bedding planes or foliations are preferentially orientated around the excavation boundary creating stress raisers which in turn facilitate the stress-driven rock mass disintegration process (e.g., as illustrated by Everitt & Lajtai (2004) on Figure 1b). Such weaknesses induce stress heterogeneities that thus promote tensile-spalling failure processes (Diederichs 2000). The observations suggest that stress induced damage can occur ?prematurely? depending on the orientation of micro and macro structures in situations where the known stress conditions should not yet initiate brittle failure processes. In general, when structural features (micro and/or macro), especially foliations, are present in a rock mass, the strength is effectively reduced, largely due to tensile strength heterogeneity in areas depending on the orientation of the structural features with respect to the excavation boundary. As a result, stress induced damage could occur in areas not normally considered due to the influence of anisotropy (Figure 1).

May 1, 2009

A modified liquation technique was developed for recovering tin from tinhouse scruff metal or hardhead containing about 10 per cent iron and 15 per cent occluded flux, palm oil, and moisture. This was effectedby heating the scruff metal to 950°C followed by rapid cooling to suppress the formation of FeSn2 and FeSn, and then subjecting it to the ordinary liquation and drossing processes of refining. By this method it was possible to recover about 83 per cent of the original tin content and, with subsequent smelting of the irony drosses, an overall recovery of 92 per cent was obtained.

Jan 1, 1969