Search Documents

By Mingming Zhang

"Three samples received from the EAF shop have been characterized by chemical, X-ray diffraction (XRD), optical microscopy (OM) and scanning electron microscopy (SEM) methods. The objective of this characterization work is to investigate the occurrence of nickel, copper, zinc, sulfur and phosphorus in these samples and identity their origin and associations with iron minerals in the concentrate samples that are from mines.The samples were identified as Mineral, Pellet, and HRD. The latter is the DR! product. All three samples were received as fine powders. The results indicate that, in the mineral sample, magnetite is the major iron oxide mineral with hematite as a second phase based on the OM and XRD studies. Pyrite [FeS2], chalcopyrite [CuFeS2] and bravoite [(Fe,Ni)S2] are major sulfide minerals. Trace amounts of apatite [Ca5(P04)3(F,Cl,OH)], wardite [Na4CaA112(P04)8(OH)8 6H20], giniite [Fe5(P04)4(OH)3 2H20] and vivianite [Fe3(p04)2 8H20] were identified by SEM and XRD. Microscopic studies also indicated that most of the sulfide grains in the mineral sample are present either as liberated fine particles (about 10 microns) or as inclusions within the magnetite and hematite grains. XRD studies revealed magnetite as the major mineral with subordinate amounts of hematite and pyrite confirming the microscopic findings. Copper, nickel, and zinc are mainly present as chalcopyrite, bravoite, and franklinite [(Zn,Mn,Fe)(Fe,Mn)204] in trace amount in the mineral samples, respectively. Impurities carry over to the Pellet and HRD samples.Chemical analyses of the three iron-bearing samples indicate that sulfur and phosphorus in the Pellet sample exceeded the specification. Since liberated pyrite and chalcopyrite particles were observed both in mineral and pellet samples, magnetic and flotation processing routes for this ore should be effective for sulfide removal but at the cost of iron losses. The high phosphorus content of all three samples indicates that there are phosphates which are difficult to remove by the current concentrating process (magnetic separation and flotation)"

Jan 1, 2012

By Xiping Chen, Wangxing Li, Jiemi Zhou

"Desulfurization methods suitable for anode-grade petroleum coke (coke for short) used in primary aluminum industry are coke desulfurization during calcination, desulfurization in soakage and desulfurization in mediums. Coke desulfurization during calcination is discussed in this paper. Influences of calcination temperature, holding time and coke granularity on coke desulfurization were discussed. Experimental results show that calcination temperature has a remarkable influence on coke desulfurization. When the temperature is high enough desulfurization ratio of coke can reach 85% only by calcination. Holding time has a definite influence on coke desulfurization, but desulfurization ratio is low at the temperature of 900~1300°C. The influence of holding time is obvious when calcination temperature surpasses 1400°C. The influence of coke granularity is smaller compared with calcination temperature and holding time.IntroductionPetroleum coke is main raw material for carbon anode in primary aluminum industry, and its weight percentage in carbon anode is about seven percent. Green coke can not be directly used for anode production because of its immanent moisture and volatiles. Green coke must be calcined in order to meet the request of anode production. Calcination is a heat-treatment process during which green coke is heated to a given temperature to remove volatiles, moisture and some sulfur. Real density, strength, electrical conductivity and anti-oxidation ability of petroleum coke can be improved by calcination and calcined coke can be received [1, 3, 4]. Sulfur in calcined coke finally goes into carbon anode. During baking or aluminum smelting, the sulfur in anode ultimately changes into SO2 and emits from anode into the atmosphere. Excess SO2 easily leads to acid rain which brings heavy pollution to the environment [1, 2]. With the development of Chinese aluminum industry, consumption of anode-grade petroleum coke increases year by year, the total consumption in 2007 surpassed 4.5 million tones and the yearly emission of SO2 from aluminum smelters has exceeded 270 kilotones. From 2005 Chinese government began to limit the emission of SO2 from primary aluminum industry, so desulfurization of anode-grade petroleum coke becomes more and more urgent. Some relationship need to be found and used to guide desulfurization of petroleum coke."

Jan 1, 2008

By M. Okido, R. Ichino, K. Kuroda

"Compound semiconductor, ZnTe, was electrodeposited in an acidic solution with K2TeO3, ZnSO4 and Na2SO4 solution. Since the reduction potential Te(IV)/Te(O) is remarkably noble from the solution comparing to Zn(II)/Zn(O), code position of Te and Zn was thought to be difficult from this solution. Resulting from EQCM analysis, furthermore, Te(IV) reduced to Te(O) and Te(-II) in this order so that Te catholically dissolved from the electrode surface at more negative potential. But ZnTe alloy were formed by the UPD of Zn at -0.7V at 298K on Te surface in lmM K2TeO3, 100mM ZnSO4 and 100mM Na2SO4 solution adjusted at pH 4. Content of Te in the deposits is, however, more than 80%.Electrolytic temperature is well known to affect on the deposits characteristics. The higher bath temperature was, the better ZnTe crystal was detected in this study. Thermal electrode method is a. process of heating only substrate by flowing ac current in substrate. This process makes the surface temperature of substrate higher than boiling point of the solution, 373K. From EDX analysis, deposits without thermal current were Te-rich, Te content in the deposits with thermal current decreased with increasing of thermal current. Te content was 62% for 5A ac current, 51 % for I OA and 45% for 20A, respectively. The deposits that produced with ac current of IOA were closed to the stoichiometric ratio, i.e. ZnTe.Consequently, thermal electrode method is more effective to obtain a good crystallized ZnTe without heat treatment after deposition.IntroductionThe current subject of solar cell materials is silicon. Compound semiconductors including GaAs and II-VI group are generally used in the developing field of digital information such as the rapid cellular phone and car telephone. Compound semiconductors consist of more than 2 kinds of element. There are many materials for these compound semiconductors such a SiC, InSb, CdS for binary system and CuinSe2 for ternary system. It becomes generally difficult, to produce high quality crystal with increasing of kinds of element due to a complicated structure and a compound ratio of element. Semiconductor materials as a device are usually simple binary compounds and/or these mixed crystals. Properties of compound semiconductors have variety of the forbidden band and lattice constant and that can be change easily by addition of another element for the usage of the solar cell. Since most compound semiconductors are direct interband transition type, which has steep optics absorption edge and large light absorption coefficient."

Jan 1, 2000

By Thomas Buenger

The Hamburg smelter of Norddeutsche Affinerie AG is situated near the city of Hamburg’s downtown and is therefore particularly subjected to fulfill environmental requirements according to the German legal regulations. Thus, investments related to increasing concentrate throughput are always linked to packages to enhance the emission status of the smelter. This connection between environmental protection and productivity enhancement should be explained by the example of the Peirce-Smith converter plant of the Hamburg smelter. Such outstanding investments can be demonstrated by the transition from scrap charging via boat from the front side to a fully automatic and completely sucked scrap charging system.

Jan 1, 2009

By D. Pradhan, R. G. Reddy

"Electrorefining of aluminum scrap was investigated from AlCl3 –1-Ethyl-3-methyl-imidazolium chloride (EMIC) (Molar ratio 1.65) chloroaluminate electrolyte using copper cathodes at temperature of 90±3°C and cell voltage of 1.5 V. The deposits were characterized using scanning electron microscope (SEM), energy dispersive spectroscopy (EDS) and X-ray diffraction (XRD). The study was focused to determine the effect of electrode surface modification as well as deposition time on dendritic depositions of aluminum. Their effect on current density was investigated also. It was shown that the surface modification of electrodes reduced the dendritic depositions of aluminum. Pure aluminum (>99%) was deposited for all experiments with the current efficiency of 94-97%. The use of ionic liquids not only reduced the energy consumption but also minimized pollutant emissions (CO, CO2 etc.) compared to the commercial high temperature aluminum production.1. IntroductionAluminum electrorefining/recycling from aluminum scrap using ionic liquid electrolyte is an attractive process today because of the unique chemical and physical properties such as wide temperature range for the liquid phase, high thermal stability, negligible vapor pressure, low melting point and wide electrochemical window. But in conventional practice, melting of aluminum scrap and high temperature molten salt electrolysis makes this process more expensive and less energy intensive (average 13 kWh/ kilogram of aluminum) [1] . Although recycling scrap aluminum requires only 5% of the energy used to make new aluminum [1-2], but the green house emissions like CO2, CO and HF have to be counted for environmental reason. Approximately, 5.31 kilogram of CO2 emitted per kilogram of aluminum production in most of the US industries."

Jan 1, 2009

By Zhang Huaiwei, Shi Xiaoyan, Li Xinlin, Sun Fei, Hong Xin

"The control of the slag properties has become very essential in improving the separation between the slag and the matte in the copper slag cleaning process. The goal of the present work is to characterize the copper converting slag through chemical analysis (XRF), X-ray diffraction (XRD), scanning electron microscopy (SEM) coupled with energy dispersive spectroscopy detection (EDS) and thermal analysis (DSC). The majority of the identified elements were Fe, Cu, Si and 0. The XRD has presented compounds such as Fe2Si04, Si02, CuFe204, Fe304, and Cu. The main existence of copper element was the metallic copper due to the entrainment loss. Slight amounts of copper were existed as the CuFe204 in the slag. The density, viscosity, electric conductivity and the thermodynamic property of the molten copper converting slag were also investigated in the study.IntroductionCopper slag, which is produced during pyrometallurgical production of copper from ores, contains materials like iron, alumina, calcium oxide, silica etc. For every tonne of metal production about 2.2 ton of slag is generated [l]. The slags of copper converting process contain about 5% of copper and about 20% magnetite. The copper are present in the slags either as physically entrapped or in chemically dissolved [2-3]. The traditional slag cleaning method is electric furnace process including two steps, intensive slag reduction and quiet sedimentation. Although the process is suitable for the various copper slags, it is also with the higher energy consumption [ 4-7]. The slag characterization studies are the fundamental step in the definition of an appropriate recycling process for saving the energy consumption."

Jan 1, 2013

By Donald R. Sadoway

The viability of treating certain forms of hazardous waste by direct electrolysis in molten oxides is under investigation. Secondary residue or waste mud produced in the course of chromate chemical production is the focus of attention in this study. The goal is to reduce the water soluble hexavalent chromium either to insoluble trivalent chromium or to chromium metal. Electrolysis tests have been conducted in a high temperature cell containing chromate sludge dissolved in an electrolyte composed of Al2O3, SiO2, CaO, and MgO. Oxygen production on a carbon-free anode has been confirmed.

Jan 1, 1992

By Shize Jin

Effect of four polyols, namely ethylene glycol (EGL), glycerol (GCL), propanediol (PDL), butanediol (BDL) and three organic acids, namely oxalic acid (OA), malonic acid (MA) and succinic acid (SA) on the current efficiency (CE) and the cell voltage during zinc electrowinning was studied. Galvanostatic polarization was conducted in a supporting electrolyte (SE) containing 180 g dm-³ H2SO4, 60 g dm-³ Zn2+ and 8 g dm-³ Mn2+ at 38°C with magnetic stirring. The imposed current density was 50 mA cm-². The anodes were made of a Pb-Ag alloy and the cathodes were made of an aluminum alloy. The results showed that all the polyols tested in this study decreased the current efficiency and the cell voltage, but the decrease of the cell voltage was not important. Oxalic and succinic acids decreased the current efficiency to a less extent than the polyols, but did not decrease the cell voltage much. The only compound that increased the current efficiency was malonic acid, and its capacity of decreasing the cell voltage was the highest within the seven tested organic compounds.

Jan 1, 2003

By C. García

Several modifications to Zaldivar's original design have been made in order to reach the design cathode production. This paper describes the modifications to the crushing, leaching, solvent extraction and electrowinning operations, which in turn have increased the production by 14.8% over the design capacity in 1999. The principal modifications were to (1) incorporate a dry pre- screening plant between the secondary and tertiary crushers to increase the percentage of fines to the piles, (2) increase the retention time of the solutions inside of the piles, and (3) increase the efficiency of the tertiary crushers to reduce the particle size of the product material. The leaching ratio was increased from 2.8 to 5.6 m3/ton. The temperature of the pregnant leach solution (PLS) was increased, the amount of acid used was reduced, and a strain of native bacteria was adapted in highly contaminated solutions. The copper concentration in the PLS was increased by more than 50% and was stabilized at this level by commissioning a process of two-stage leaching. The current density in the tankhouse was increased from an average of 2 16 to 3 17 A/m

Jan 1, 1999

By Seung-Whee Rhee

Characteristics of ceramic support made by spent foundry sand-loess mixtures are investigated by bulk density, porosity, durability, and compressive strength. And the basic properties of SFS and loess are estimated. The effect of drying time after cutting process, elevated temperature time, sintering temperature, and sintering time is also estimated to obtain the optimal condition in the process of manufacture ceramic supports. From the basic properties of SFS and loess, the content of SiO2 in furan sand is much higher than that in loess but the content of Al2O3and Fe2O3 in furan sand is much lower than that in loess. In order to make ceramic supports cylinder shape is the most desirable to sustain the properties of ceramic support. If annulus shape has a enough compressive strength, however, annulus shape may be decided. For the optimal condition to manufacture ceramic supports, drying time after cutting process is decided to 24 hrs and elevated temperature time is decided by 9hrs. And sintering temperature and sintering time are decided to 900 and 9hrs, respectively in order to prevent solidification of sand materials.

Jan 1, 2006

By Hector M. Henao

In order to provide the thermochemical data regarding the slag system, which are of importance for sulfide smelting and metallurgical processes but still lacking, an experimental study was carried out on the phase relations and activity of iron oxide in the FeOX-CaO-SiO2 system at temperatures between 1300 and 1400 °C and partial pressures of oxygen between 10-9 and 10-4atm. First, the solubility of CaO and SiO2 in the solid FeO were obtained and the tie lines connecting between the solid wustite (FeO) or magnetite (Fe3O4) phase and the liquid phase were determined. Secondly, iso-activity lines for FeO in the homogeneous liquid region were determined, based on the activity of iron in the Pt-crucible used in the equilibrium experiments. The activity coefficient of FeO in this region was also derived from the composition of FeO and FeO1.5 in the liquid region. Finally, the effect of (CaO/SiO2) ratio in the system and partial pressure of oxygen on these thermochemical quantities is discussed.

Jan 1, 2006

By Peter G. Smith

Tri-calcium aluminate (TCA) is a dominant alkaline component of the red mud residue from the Bayer process. A method being considered for industrial implementation partially neutralizes the residue by contacting it with gaseous CO2. This paper outlines the chemistry of CO2neutralisation of TCA under conditions relevant to the treatment of Bayer residue. CO2 neutralisation of the liquor is fast. It results in the formation of amorphous aluminium hydroxide and dawsonite that agglomerate together. Neutralisation of solid TCA is slower and leads to the formation of calcite, dawsonite and amorphous aluminium hydroxide. The dissolution of TCA in partially neutralised slurries causes pH reversion. However the carbonated solutions contain a store of bicarbonate that can supply aqueous carbon dioxide to complete the transformation. The pH at which the carbonation is carried out will affect the degree of TCA transformation during the carbonation process. In particular, if the pH of the carbonation is too low (near 7.0), calcite precipitation is inhibited and the degree of transformation is low. Controlling the carbonation pH helps to optimise the neutralisation process.

Jan 1, 2003

By Guozhu Ye, Mikael Larsson, Eric Burström, Sten Ångström

"Increased use of scrap in steelmaking including scrap use in BOF has a high economic and environmental potential in terms of increased productivity, energy saving and reduced emission of CO2. Preheating and surface cleaning of steel scrap is a concept developed by MEFOS in a four year research program funded by MISTRA, Swedish Foundation of Strategic Environmental Research. The process concept consists of four major steps: 1) Combustion of ASR or other waste fuel and composing of the gas composition. 2) Scrap heating and cleaning in a shaft where the coated zinc is removed as ZnCl2 and scrap is heated to about 600 ºC. 3) Dust separation for recovery of metal zinc. 4) Gas cleaning. This paper will describe the process concept and highlight the major results from preliminary trials around the scrap heating and cleaning shaft.IntroductionSteel is often coated to increase the corrosion resistance. Share of coated and galvanized steel in the world marked is steadily increasing. This results in increased amounts of scrap with different types of coatings. Use of galvanized scrap in EAF plant results in an EAF dust with high content of zinc ferrite and many other impurities like Pb, Hg, Cd and halide. EAF dust is classified as hazardous waste in most of the developed countries and the steel plant has to pay for external treatment for zinc recovery. For use in BOF plant this will result in a BOF dust containing typically 1-5%Zn making it impossible for recycling to the blast furnace.Different approaches for surface cleaning have been investigated in past. Dapper et al. [1] examined the possibility to evaporate Zn, Ni, Cr, Sn from coated materials using chlorine. Chlorinated rinsing of non iron oxides and metals using HCl from combustion of PVC was discussed by Fray [2]. Further studies by Tee and Fray [3-5] have been concentrated on the possibility to vaporize coatings with an air and chlorine gas mixture. The O2:Cl2 ratio in the gas mixture was found to have great importance for control of the process. To avoid the chlorination of iron, this ratio should be kept at a level of 10:1.Scrap pre-heating up to about 600 ºC is a well known method and this alone could save up to 100 kWh per ton steel. The technology has been established since many years and efficient processes were developed in the 90’s. However, no process has fully gained the expected energy savings as the large quantity of the exhaust gas has to be reheated to over 1000 ºC again to destroy the hazardous components like dioxins."

Jan 1, 2008

By E. Morrice

Solubility of yttrium oxide (Y203) in fluoride melts was experimentally measured in the temperature range of 998 to 1273 K and, YF3 composition in LiF.YF3 melts varying from 20 to 50 mole pct using a graphite crucible in an argon atmosphere. Solubility of oxide in the melt was found to increase with increasing temperature and YF3 composition in the melt. An expression for in XY2O3 as a function of temperature for several melts was deduced. The calculated activity coefficients of Y2O3 in the melts exhibited a negative deviation from Raoult's law.

Jan 1, 1989

By Sergio Sanchez-Segado, Yuan Zhang, Animesh Jha, Ahmad Fahmi Ruzaidi

Niobium and tantalum are considered critical materials because the increasing demand in the energy sector which is reliant on limited abundance of these two metals in minerals. Traditionally, niobium and tantalum mineralsare digested using hydrofluoric acid at moderate temperatures, producing oxy-fluorides which are separated by solvent extraction, involving the use ofhazardous chemicals. The increasing environmental pressures are forcing the industry to search for alternative low carbon processing methods. In this paper alkali roasting based separation and beneficiation, which is not well understood in the literature, is proposed, for which the kinetics and thermodynamic equilibria for the formation of sodium tantalate and niobate with sodium hydroxide are analyzedat the temperature range of 400ºC to 700ºC. The apparent activation energy of formation,changes from 31.0±0.8 to 22.3±1.2 kJ mol-1 and from 23.8±1.2 to110.2±12.8 kJ mol-1, for tantalate and niobate, respectively. The reaction mechanism is examined on the basis of the analysis of reaction products using X-ray powder diffraction (XRPD) and X-ray fluorescence (XRF).

Jan 1, 2015

By M. Olper

Today, copper production from direct leaching of oxidized copper ores followed by solvent extraction-electrowinning (SX-EW) accounts for about 15% of the total primary world output. SX-EW is a well-accepted process with an operating cost in the range 16-20 cents/lb. copper for small and medium size plants, depending on the plant size and local conditions. However, this technology presents some drawbacks that affect the operating cost and cause environmental concerns. ENGITEC and Paques Bio Systems have developed a new process that avoids the solvent extraction step and operates the copper electrowinning step at a lower cell voltage because of the depassivation of the anodic reaction. The consequence of this new concept is that the direct operating cost is in the range 10-12 cents/lb. copper. This new process is composed of the following steps: ? Selective precipitation of copper from leach solutions by biogenic H2S, yielding CuS and regenerating acid ? Leaching of the CuS with a ferric fluoborate solution to dissolve copper and produce elemental sulphur that is recycled back to the H2S biogeneration step ? Electrowinning of copper fluoborate solution in a diaphragm cell with the ECUPREX® Process, producing copper cathodes and regenerating the ferric fluoborate solution to be recycled back to the leaching step ? Biogeneration of H2S from the elemental: sulphur generated during the leaching step, with the nutrient source for the anaerobic bacteria selected form a wide range of organic substances and/or some industrial by-products containing carbon and hydrogen This paper describes all process steps with particular reference to the biological H2S generation technology. Also discussed' is the capability of the ECUPREX® Process to treat copper sulphide concentrates and copper matte.

Jan 1, 1999

By Tarek M. Abd El Hamid, Suzane Ali

"Treatment of industrial waste materials is created serious problem in Egypt. Aluminium sludge is generated as a by-product from aluminium household industry which contains significantly high alumina content exceeding 90%. This by-product randomly disposed and creates serious environment problems to locate community. To develop the treatment process of this material, the recovery of high purity alumina and identify the potential application is being the primary objective, This paper represents the recovery process of alumina process waste sludge High purity alumina material <99.8% aluminium oxide with originate particle size 0.125-0.420mm and apparent density 0.39g/cm3 was obtained with a specific surface area 139m2/g. Alumina produced was modified by cerium oxide doped alumina. The catalytic activity and selectivity was investigated in conversion of iso-propanol via dehydrogenation reaction yielding only acetone indicating an excellent selectivity the dehydrogenation. The presence of 10% CeO2 increase in the catalytic activity of 82% for the originated alumina. Introduction Approximately 20 thousand tons of aluminium waste produced in Egypt in 2006 with increasing amounts expected in succeeding years. A part of this waste contains organics impurities which coexisted with aluminium waste as a result of manufacture final aluminium products, waste usually content <1 to 2 wt% of organic carbon. It's generally admitted that the organic species are present in the form of lubricant oils used in rolling and pressing equipments for aluminium sheet. Both industry and government face possible high-cost disposal problems that more magnified by large volume of waste produced. The alumina recovery leachable study conduct in this paper had the following objectives: 1- Develop a process that can provide an environmentally acceptable residue and also recover the available alumina. 2- Evaluate the alumina produced in terms of grade and catalytic application."

Jan 1, 2008

By Wenjie Zhu

Hexavalent chromium is a widespread environmental contaminant. An Achromobacter sp. strain nominated Ch1 can reduce soluble and toxic chromate to insoluble and non toxic Cr(III) in aerobic cultures, and no Cr(VI) decrease was observed in anaerobic cultures. In contrast with other Cr(VI) reducing microorganisms, Ch1 showed higher Cr(VI) reduction at high pH. Reduction performed under alkaline conditions at pH 7 to 11, and the optimal pH was 10. During the reduction, pH decrease was observed may caused by production of acidic metabolic byproducts from aerobic respiration. In the present study, the ability of Achromobacter sp. Ch1 to reduce Cr(VI) during growth was evaluated with lactate as an electron donor. In NB medium, Ch1 reduced 100% of 24mM of Cr(VI) in 35h, but only 73% of 30mM of Cr(VI) after 48h of inoculation. Reduction was inhibited by metal ions like Ag+, Cu2+, Zn2+, slightly inhibited by Mn2+, and not affected by Mg2+. Results revealed that reduction rate of Cr(VI) also increased with the increasing of concentrations of lactate, and complete reduction was achieved at the concentrations above 40 mM. HPLC analysis demonstrated Cr(VI) reduction was associated with the consumption of lactate. There was a large quantity of dark blue sediment generated in the culture during Cr(VI) reduction by Ch1. Energy dispersive X-ray (EDX) analysis showed that the major element composed the formed sediment was chromium presented as Cr(OH)3 precipitate. The features characterizing Cr(VI) reduction by Achromobacter sp. Ch1 are high Cr(VI) concentrations and high pH.

Jan 1, 2006

By T. Watanabe, T. Fujiwara, S-Wan Song, Y. Nakagawa, R. Teranishi, M. Yoshimura

"We have tried a new method to fabricate cobalt oxide films onto porous films directly by an electrodeposition method at low temperature. The porous substrate films (membrane-filters and paper) were placed between a LiOH solution and a CoSO4 solution and treated under electricalcurrents of ~1 mA/cm2 using carbon cathode and anode. Effects of temperatures, flow rates and electrical currents have been investigated. As a result, we found that the LiCoO2 films and Co3O4 films were successfully fabricated on paper and/or porous PTFE filters at 120 °C, while CoOOH films were deposited at 80 °C. Furthermore, LiCoO2 films did not cover whole the substrates, but was fabricated just over the anode. The chemical reactions of electrodeposition were also considered from these results.IntroductionRecent agreements on global environment require rapid progress of low energy and low waste processings for the fabrication of thin films that succeed to the mass production with the high consumption of the fossil fuels (such as physical vapor deposition°, chemical vapor deposition2), dip coating with firing3) etc.). The total energy consumption in aqueous systems should be the lowest among all these processing routes, because a much lager excess of energy is necessary to create melts, vapor, gas, or plasma than to form an aqueous solution at the same temperature4)The ""Soft Solution-Process"" (SSP) was one of the best concepts to realize the low energy and low waste fabrication of inorganic materials. 5) Generally speaking, SSP gives similar results to any other processing using fluids (such as vapor, gas plasma) and/or beam/vacuum processing. However, the total energy consumption of all these possessing routes should be the lowest in aqueous systems, because a much larger excess of energy is necessary to create melts, vapor, gas or plasma than to form an aqueous solution at the same temperature (Fig. 1). This idea can be easily demonstrated, using the simple example of BaTiO3. The energy diagram for the formation of BaTiO3 from various precursors is shown in reference 4. The driving forces (AG) for representative synthesis reaction of (1), (2), (3), (4) and(5) are 38, 727, 3685, 17 and —14kcal/mol, respectively at room temperature. 6' 7"

Jan 1, 2000

By Toshihide Takenaka, Takashi Matsui, Nao Murakami, Masahiro Kawakami

"Electrowinning of Ti have been investigated in a LiF-NaF-KF melt including K2TiF6 at 773-923K by applying electrochemical oxidation ofH2 gas as an anodic reaction. The cathodic behavior of titanium and the anodic behavior of H2 gas were studied by voltammetry in detail to clarify the electrolytic condition for the process. The electrowinning of Ti was carried out by potentiostatic _electrolysis. Steady electrolysis was achieved under the suitable electrolytic condition without breaking out the anode effect. Titanium metal was electrodeposited on a Ti cathode though the deposits were usually powdery. It is concluded that this process is potential if the morphology of the deposit can be improved.IntroductionTitanium has such good properties as high specific strength and high corrosion resistance. However, the availability of Ti has been limited because the price of Ti is much higher than those of other common metals, such as Fe and Al. The production process of Ti ingot from its ore is rather intricate so that the production cost is high. If the simpler process is developed, the production cost should be retrenched. Titanium metal is usually produced by the Kroll process, which consists of the electrowinning of Mg metal in molten salt and the chemical reduction of TiCl.i by Mg metal. The Kroll process is very elabrate, but not simple. Because the chemical reduction ofTiCl4 by Mg metal is highly exothermic, a considerable amount of energy is wasted.Titanium metal can be electrowon in molten salt bath in principle. A simpler and more effective process than the Kroll process may be realized by the direct electrowinning so that the electrowinning of Ti metal has been studied widely[ 1]. Some researchs progressed to a pilot plant stages [2], but the electrowinning of Ti has not been industrialized yet."

Jan 1, 2000