Search Documents

By M. J. U. T. Van Wijngaarden

SYNOPSIS The corrosion characteristics of a new steel, 14Cr, which is a modification of the well-known 3CR12, in aqueous sulphate solution were studied through polarization diagrams and a computer analysis based on the polarization¬resistance technique. It was found that the corrosion rate of 14Cr steel is independent of pH for pH values above 6, but, below a pH value of 4, the corrosion rate increases sharply with decreasing pH. In air-saturated solutions of neutral and mildly alkaline pH, the corrosion rate is approximately 60 µm per year. The 14Cr steel shows a twentyfold improvement in corrosion resistance over that of 3CR12 in sulphate solutions at pH 2,0. This is considered to be due to the beneficial effect of its higher chromium and nickel contents.

Jan 1, 1985

By S. Nana, M. B. Cortie

Duplex stainless steels containing high levels of manganese and copper and lower-than-normal levels of nickel were produced and evaluated. The experimental alloys containing 3 per cent copper by mass could not be successfully hot-rolled. Alloys containing less than 2 per cent copper could be hot- and cold-rolled without difficulty. The wrought experimental alloys that contained copper were found to offer some advantages over the 2205- type duplex stainless steel in sulphuric acid at 52°C. Resistance to pitting attack was governed primarily by the chromium, molybdenum, and nitrogen contents, and one of the experimental alloys was superior to the 2205-type alloy in the ferric chloride test. It is concluded that manganese is a useful substitute for nickel in duplex alloys, but that further work is required before the present alloys, or variations of them, could be commercially viable.

Jan 1, 1993

Minutes of the Annual General Meeting Held at Harmony Country Club on Wednesday, 2nd August, 1978, at 7.30 p.m. Mr A. N. Shand (Chairman of the O.F.S. and Klerksdorp Branch) was in the Chair. Also present were:.... Induction of Chairman Mr A. N. Shand introduced Mr H. M. W. Eschenburg by briefly outlining his past career and achievements, and, in calling upon him to take the Chair, wished him a very successful year of office..... Address by the President of the S.A.I.M.M. The Chairman introduced Mr Von Wielligh by outlining his career and achievements. After completing his education, he joined J.C.I. in 1936 as a sampler, and from that time served the company in many capacities, culminating with his appointment to the Board in 1974.....

Jan 1, 1979

By A. J. Buchan

The wear of steel pipelines used for the transportation of backfill slurries is frequently regarded as an erosion problem only. An investigation was undertaken of the likely contribution to the total 'wear rate' made by corrosion. Use was made of a pipe flow loop with catholically protected specimens and corrosion inhibitors. Laboratory electrochemical tests utilizing a rotating-cylinder electrode were also conducted. The slurries used were classified tailings from two mines at a relative density of 1,7. The velocities were between 2 and 4,9 m/s. Substantial decreases in the wear rate of up to 80 per cent for one slurry and up to 67 per cent for the other were obtained with the use of corrosion control, showing that corrosion and, more importantly, interaction between erosion and corrosion, contribute a significant portion of the overall wear in steel pipelines

Jan 1, 1994

By P. A. Laxen, P. J. van Staden

In situ leaching tests with thiourea as the lixiviant were caried out in two worked-out stopes at the No. 6 shaft at Rand Leases Gold Mining Company. Dissolution rates of 0,9 and 0,7 9 of gold per week per 100 m2 of footwal area were achieved. A major disadvantage of the method seems to be the slow rate of dissolution of the gold, which is probably caused by poor contact and slow mass transfer between the lixiviant and the gold surfaces. Under full-scale application, the loss of lixiviant by leakage could also be a very important factor. Furthermore, the oxidation products of thiourea may 'poison' the activated carbon that is used for the recovery of the gold. The method may therefore be economically viable only in stopes that contain high values of residual gold.

Jan 1, 1989

By D. R. Arnold

Discussion of the above paper by D. R. ARNOLDt This paper is the result of an excellent piece of work performed as a service to hyUrometallurgy in general and to the South African uranium industry in particular, and the authors are to be congratulated, Authors' reply Dr Arnold is correct in saying that the present Senbrix resins, which are based on the experimental heavy resins first developed at the National Institute for Metallurgy (NIM), need not necessarily show the same poor performance with respect to cobalt poisoning as the NIM prototypes. Oceanology International The next 01 World Conference is to be held Brighton, England, from 2nd to 7th March, 1980. The programme will concern technical advances in the offshore oil and gas industries, and is expected to include 140 papers from 20 countries.

Jan 1, 1979

By C. Norden

The purpose of this article is to show how a representative overall equipment effectiveness (OEE) measurement can be calculated for an underground coal mining bord and pillar batch process. The calculation method, the typical losses (which include planned and unplanned availability losses, coal quality losses, and process rate losses) and the underlying logic are presented and discussed. It is argued that the current traditional underground bord and pillar mining process can currently provide a maximum theoretical OEE of only 49 per cent, while a realistic benchmark target should be in the order of 37 per cent, which relates to an average of 2400 t per shift or 1.2 Mt/a. In addition, it is argued that the current bord and pillar process is the current bottleneck to further improvement past the 2400 t per shift benchmark, and that fundamental process changes will be required to eliminate this bottleneck.

Jan 1, 2012

By I. M. MacGregor

This paper discusses the possible use of petrological data and proximate analyses in the prediction of cutting forces for coal. It is restricted to the development of univariate predictors based on data from thirteen collieries in five major Transvaal and Orange Free State coalfields and three coal provinces. The aim of the work was the identification and development of the best predictors of mean peak cutting force and Hardgrove grindability index from among the independent variables evaluated. The data, which were obtained by use of the penetrometer developed by the Chamber of Mines Research Organization, were processed according to the SPSS computer package. The analysis revealed reasonable correlations between the Hardgrove grindability index and (1) the volatiles and vitrinite content in the Vereeniging-Sasolburg and South Rand Coalfields, (2) the contents of vitrinite, vitrinite plus exinite, and minerals plus inertinite in the Eastern Transvaal Coalfield.

Jan 1, 1985

By M. J. U. T. Van Wijngaarden, A. T. Pieterse

An account is given of the performance of a 37 MVA electric-arc .furnace in which bottom stirring with inert gas by an indirect-contact stirring-plug system was applied. The system, which was developed and patented by Thyssen-Stahl AG, and which is the first inert gas stirring system to be installed in South Africa, was commissioned in January 1992. Initial problems were experienced due to the blockage of stirring plugs by molten steel. The causes of these malfunctions are examined, and an account is given of how they were overcome. The system is described and evaluated. A comparison with direct-contact stirring systems shows why Iscor Vereeniging Works considered it to be more suitable for their Vaal Melt Shop. The results show that, through the successful application qf this technology, Iscor Vereeniging Works has achieved an annual cost saving of more than R2,5 million.

Jan 1, 1994

By G. W. Healy

The smelting of calcium carbide has always been plagued by eruptions, too often with serious injury y or loss of life. To find their causes, the author calculated an internal energy balance using 1992 data for CaC2 and CaO, and older data for the remaining items. The heat content of the charge, and that of the hot gases formed at the reduction temperature, showed that only a fraction of its heat content can be supplied by these gases. Laboratory data on the electrical resistivity of fine mixtures of coke and non-conductive solids were extrapolated to a commercial carbide charge, and then used to calculate the heat produced by current flowing through the mix from the electrode surface to the hearth, which, under favourable conditions, sufficed to bring the charge to 1900 K and higher, at which temperatures reduction could take place.

Jan 1, 1995

1. Journals Quarterly Journal of tke International Tin Research Institute, edited by Colin J. Evans and published by the Institute, Fraser Road, Greenford, Middlesex UB6, 7AQ, England. Engineering, building and construction law review, edited by P. C. Loots and published every two months by Construction Law Review (pty) Ltd (P.O. Box 78020, Sandton 2146, Transvaal), R63,00 per year. 2. Publications of the Mineral Policy Sector Nepkeline syenite and feldspar by B. W. Boyd Potask by G. S. Barry Selenium and tellurium by D. A. Cranstone Sodium sulphate by G. S. Barry Tungsten byG. G. Law-West 3. Mintek reports Report M114 Analytical methods associated with the recovery of uran~um. Report M117 An assessment of tke merits of various types of balls in tke milling of ores. Report MU1 Tke determinatl:on of trace elements in coal by atomic

Jan 1, 1983

1. New books from The Institute of Metals Physical and elastic characterisation, edited by M. McLean. 1989. 228 pp. £25.00.High nitrogen steels, edited by J. Foct and A. Hendry. 1989. 461 pp. £49.50. Proceedings of the First International Calcium Treatment Symposium. 1988. 116 pp. £15.Design for recyc/ability, by Michael E. Henstock. 1988. 150 pp. £15. Solidification processing. 1988. 549 pp. £45.Proceedings of the First International Calcium Treatment Symposium. 1988. 116 pp. £15.Marine engineering with copper-nickel. 1988. 103 pp. £18.Sir Henry Bessemer: An autobiography. 1989.380 pp. £16.95. 2. Other publishers Occupational safety and accident prevention. Behavioural strategies and methods, by C.G. Hoyos and B.M. Zimolong. Amsterdam, Elsevier, 1988. 218 pp. Dfl. 180.00. Algorithms in real algebraic geometry, edited by Denis S. Arnon and Bruno Buchberger. London, Academic Press, 1988. 274 pp. £15.95.

Jan 1, 1989

The following diagrams should replace the Figs. 4, 5, and 6 that appeared on pages 412 and 413 of the October 1986 issue. These relate to the paper entitled' A new method for the rapid float-sink analysis of coal fines' by J-P. Franzidis and M.C. Harris Womanpower In 1981 the Publicity Committee of the Federation of Societies of Professional Engineers (FSPE) decided that one way in which the engineering manpower pool could be increased would be by the introduction of womanpower to the profession. Since then, Std 9 and 10 girls have been invited to attend the engineering winterschools held annually at the various universities under the auspices of SAFUES. Coal-mining wastes The 2nd International Symposium on the Reclamation, Treatment and Utilization of Coal Mining Wastes will be held in Nottingham (England) from 7th to 11th September, 1987.

Jan 1, 1986

By G. Peinaar

Superhardening is a new development by which a substantial increase in hardenability above the normal can be achieved in Iow-alloy steels. This paper concerns the reversible temper-embrittlement behaviour of steels with a superhardenability characteristic. Steels of type BS 530A40 with manganese modifications varying from 0,72 to 1,27 per cent in the superhardenable and conventional condition were compared. It was concluded that superhardenability in itself does not affect the susceptibility of a particular steel to temper embrittlement. However, an increase in manganese content, which was intended to increase the base hardenability of the steel, caused serious deterioration of the temper-embrittlement properties. As the use of manganese, chromium, and nickel to increase base hardenability results in an increase in susceptibility to temper embrittlement, it is suggested that this effect should be countered by the addition of 0,2 to 0,3 per cent molybdenum.

Jan 1, 1984

By J. D. Flint

A description is given of the extraction of pillars in a seam of coal which normally varies in thickness from 10 feet to 14 feet using conventional trackless mechanised units. By using the pocket and fender method of pillar extraction, the high capital cost of hydraulic supports is eliminated, and a volumetric extraction of 85% to 90% of the seam of coal is possible. This method of mining opens up the possibility of extracting vast tonnages of coal which hitherto would have been left in situ as pillars. The major benefits likely to accrue from this technique are seen as follows: 1. Greater volumetric extraction of the seam; 2. Longer panel life with less frequent transferring of sections; 3. Preservation of our natural resources. The authors deal with the history of this development at Springfield Colliery, discuss the present results and outline the future trends in the light of current experience.

By Y. Zhen, N. Topliffe, G. Shou

The typical service life for a long distance slurry pipeline is15 to 25 years. Determination of wear rate for a pipeline could have a high economic impact on the pipeline project. Wear is a combination of chemical corrosion and mechanical abrasion. The contribution of each factor has to be determined project by project. Normally, chemical corrosion dominates the pipe wear in fine slurry pipelines. These pipelines have been designed with a velocity between 1.5 m/s and 2.5 m/s. Solids are suspended with high homogeneity across the pipeline section. Bottom wear is not much greater than the top wear and not sensitive to velocity. The wear pattern in the pipeline transporting medium coarse solids, such as milled ore and tailings, is different. Wear concentrates on the bottom of pipeline and the outer bends, and is more sensitive to flow velocity. Wear distribution along the pipelines is similar.

Jan 1, 2007

By R. J. Davidson, W. D. Douglas, J. A. Tumilty

SYNOPSIS Two pilot plants operating on different types of carbon were used to generate steady-state adsorption data in the treatment of gold-plant solutions of high and low tenor. A pilot plant comprising three 4 m long columns and using 3 mm extruded activated carbon was used to treat pregnant solutions with a gold concentration of 5 to 8 g/t at pH 10 to 11,5. Column influent was pumped at a super¬ficial flow velocity of 0,5 m/min while the carbon was moved daily so as to effect gold loadings on the carbon of 5 to 10 k /t. With a carbon-bed depth of 12 m, an adsorption efficiency of 99,9 per cent was obtained in a bed depth of 9 m, which was subsequently reduced to 8 m when the depth of the carbon bed was reduced to 8 m. This improvement in efficiency was attributed to the reduced residence time of the carbon from 12 to 8 days. A corresponding decrease in adsorbed silica indicated that some silica fouling of the carbon had occurred. A second pilot plant, comprising a single column 6 m in length and using coconut-shell carbon of 1,0 to 2,4 mm, treated a solution with a gold concentration of 0,7 g/t at pH 8,0. Feed solution was pumped at a superficial flow velocity of 1,0 m/min while carbon was moved every 8 hours to give gold loadings of more than 5 kg/t. An adsorp¬tion efficiency of 99,5 per cent was indicated at steady state. Intermittent washing of the column with dilute hydrochloric acid was shown to have a beneficial effect on the gold adsorption and to reduce the pressure drop across the column. Intermittent washing with dilute sulphuric acid indicated that there had been some passivation of the car¬bon during the treatment of a solution with a gold concentration of only 0,2 g/t. Compared with other adsorption systems, the countercurrent moving bed appears to offer significant advantages in terms of metallurgical efficiency and capital investment. The inability normally associated with moving-bed systems to treat solutions containing suspended solids may be overcome to a degree by the use of relatively coarse extrud¬ed carbon.

Jan 1, 1985

By S. R. Xie, S. Gong, E. P. Li, S. S. He, Y. J. Sun, S. J. Li

"Based on the complicated geological production conditions and abnormal strata behavior of the fully mechanized caving face No. 102 in the Xinyang Coal Mine, we analyze the breaking and forming process of distinguishing key block structures in close spaced coal seams. This analysis establishes an integrated mechanical model of these distinguishing structures. Furthermore, the horizontal force TAB generated by downward key blocks A and B is quantified, as is the Pressure PG exerted by key block B on caved gangue. Finally, the interaction mechanism is revealed. Analysis of the results using Mathematica reveal the following: 1. Both TAB and PG exhibit approximately inverse relationships to coal pillar width b; 2. TAB exhibits an approximately exponential relationship with mining height M of which the base is greater than 1; 3. PG exhibits an approximately arctangent relationship with mining height M. Combining these results with field observations, we conclude that the area in the vicinity of supports 100#–120# in the upper area of working face No. 102 is the likely zone of abnormal strata behavior. Thus, this area was classified as a key control area. Based on these results, the graded support control technique is proposed. Application of this technique in the field resulted in a reduction in the rate of hydraulic support system malfunction from 47% to 7% in the key control area. In addition, during times of periodic mining pressure, the roof caving height value never exceeded 0.3 m and the maximum spalling depth never exceeded 0.2 m. Overall, the results indicate that this new technique has markedly increased the stability of surrounding support rock material. IntroductionClose-spaced coal seams are widely distributed in China, and mining proceeds from the uppermost to the lowermost seam (Zhang et al., 2008). In the case of coal seams in close proximity, a particular set of risk factors becomes pertinent. These include disturbance of lower seams during the mining of overlying ones and the decrease in mechanical stability of lower coal seams following repeated movement of key blocks in main coal seam roofs. This inevitably results in behaviour such as heavy wall spalling and support damage to fully mechanized caving faces in lower-lying coal seams, which necessitates a significantly increase in the measures to support surrounding rock material (Zhang et al., 2010; Huang et al., 2013; Xie et al., 2013)."

Jan 1, 2016

1. Book reviews Underwater tools, by Donald J. Hackman and Don W. Candy. Columbus (D.S.A.), Battelle Press, 1981. 152 pp. $32,95. Reviewer: B. Schmitz Uranium exploration case histories. Proceedings of Advisory Group Meeting Vienna, IAEA, 1981. Price: Austrian schillings 630. Reviewer: E. C. Kostlin Jet cutting technology, a review and bibliography, edited by Robin Brown. Published by BHRA Fluid Engineering, Cranfield, Bedford MK430AJ, England. Reviewer: D. O'Beirne 2. New Books Proceedings, Twelfth Congress of the Council of Mining and Metallurgical Institutions, by H. W. Glen (editor.) Johannesburg, The South African Institute of Mining and Metallurgy, 1982. 2 vols., 1060 pp. R78,85 (air-mail RI53,85). Amborite. Johannesburg, De Beers Industrial Diamond Division (P.O. Box 916), 1982. 6 pp. Free of charge. 3. New Journal BHRA Fluid Engineering has announced its new journal World Ports and Harbour Abstracts and the associated newsletter World Ports and Harbour News, which are issued from January 1983. The Abstracts is published bi-monthly and costs £60 in the V.K. and E.E.C., and £72 elsewhere. 4. Mintek reports Report 2134D On-line analysis, by X-ray diffraction, of fluorsparcontaining slurries. (First published 30th Sep., 1981.) Report 2135D A preliminary on-line analysis, by X-ray diffraction, of pyrite-containing slurries. (First published 30th Sep., 1981.) Report M28 The measurement of flow velocity distribution in fluids. Report M34 The determination, by atomic-absorption spectrophotometryusing electrothermal atomization, of platinum,palladium, rhodium, ruthenium, and iridium. Report M45 Two computer programmes for the calculation of massand heat balances in the production of high-carbon ferromanganese. Report M50 The development of an on-line gold analyser. Report M54 Major amounts of mercury in native gold from upper Witwatersrand sediments. Report M55 A new robust method for the treatment of analytical data. Report M57 The hydrometallurgical treatment of liquors generated by the leaching of a low-grade matte. Awards for inventions For inventing devices of exceptional value to the mining industry, two mining men were presented with awards in Johannesburg on 25th November, 1982, under the Chamber of Mines' Ideas and Suggestions Scheme. Mr W. W. Malan, President of the Chamber of Mines, made the presentations.

Jan 1, 1983

The May General Meeting of the Institute was held in Kelvin House, Johannesburg, on 21st May, 1969, at 4.30 p.m. Mr J. K. E. Douglas (Vice-President) was in the Chair. There were also present twenty-two Members, including Messrs F. P. Bath, M. Bareza, A. R. C. Fowler, D. M. Jamieson, C. M. Mavrocordatos, D. G. Maxwell and J. A. Nixon (Council Members), Messrs T. Davidson, G. L. Diering, E. T. Dunstan, D. E. H. French, K. Hodgson, O. A. E. Jackson, A. F. Lee, A. Louw, D. L. Starkey, R. K. Wheeler and M. Youngworth. Four Associate Members including Messrs D. Blair Hook and G. R. Still. One Student Mr N. A. Barcza. Thirteen Visitors, including Messrs S. H. Ash, D. L. G. Bayne, E. Bayne, S. Bell, W. S. Garrett, L. S. Gibbs, R. C. Hamilton, M. Maguire, D. Rose and J. D. van Niekerk. Total Present: Fourty-one. OBITUARY The Vice-President: "It is my sad duty to announce the death of the following member of the Institute: Thomas Spence Haldane, Member, who joined the Institute in 1924 and passed away on 21st December, 1968. As a mark of respect to the memory of the deceased and in sympathy with the bereaved, those present stood and observed silence for a few moments. MINUTES The Vice-President requested that confirmation of the minutes of the previous meeting be held over as they would only be appearing in the Journal of the following month. He also requested that confirmation of the minutes of the 75th Anniversary Meeting be held over. MEMBERSHIP The Vice-President: "I have much pleasure in announcing that the names of the under-mentioned candidates have been published in accordance with By-Law 5.2.2, and Council has elected them to membership of the Institute in the following grades: Members: Gideon Jacob Haumann, Peter John Cumming, Ian Stanley Dudman, Roderick Goldston Murchison. Associate Members: Francois Alwyn Beyers Fouche, Alan Marsh, Johannes Petrus van der Westhuysen, Waldo Edmund Stumpf, Ian Nicholas Ridley. Affiliates: Lutgerus Kolver Jooste, Roger Ainsley Ralph Kebble, Edward John Wainwright, Lewis William Davies. Graduate: Clive Graham Knobbs. MEMBER TRANSFERED TO A HIGHER GRADE From Student to Associate Member: Diethard OUo Eduard Fahrbach. I welcome the newly elected members to the Institute and congratulate the member who has been transferred to a higher grade." (Applause).