Search Documents

By Franc R. Joubin, Donald H. James

"The Property of Rix Athabasca Uranium Mines Limited is in the Beaverlodge area of northwestern Saskatchewan. The mine is 7 miles by road north from the Lake Athabasca port of Bushell which is 250 miles north by aircraft or boat from railhead at Waterways, Alberta.The Rix property is a portion of the former DD 1 concession, obtained in 1949 from the government of Saskatchewan when private prospecting for uranium became permissible. The concession was prospected in detail during the 1950 and 1951 field seasons and a great many radioactive show-ings were discovered. Development and drilling were concentrated in two and later three of these areas, and by late 1952 enough ore had been indicated in the Leonard series and ""Smitty"" zone to justify underground development by adit-drift and shaft respectively.Four hundred feet of drift development on the Leonard No. 1 vein and the sinking of a two-level vertical shaft with related lateral development on the Smitty zone were completed in 1953. In April 1954 the Smitty section was placed in production at a rate averaging 100 tons per day, thereupon becoming the first privately owned post-war uranium producer in Canada. The ore is shipped for processing 12 miles by truck to the mill of Eldorado Mining and Refining Limited.Until recently all of the Company's production was drawn from the Smitty orebody. In April, 1955, ore production commenced from the faulted west extension of the Smitty structure, known as the Rix 62 zone, and from the Leonard No. 1 vein.The Smitty orebody (see Figure 2) is an intensely brecciated lenticular zone bordering both sides of the Smitty fault. The breccia areas are irregularly mineralized with pitchblende, very sparse galena, and pyrite in a gangue of feldspar, chlorite, calcite, and silica, all thoroughly soaked with fine-grained hematite to produce the locally-called ""red alteration"".Tenor of the ore currently being mined is classified information. The average grade estimated, prior to production, was 0.20 per cent (4.0 lbs.) U308 per ton."

Jan 1, 1949

By Haofeng Xie, Lijun Peng, Xujun Mi, Xue Feng, Xiangqian Yin, Zhen Yang, Guojie Huang

The Cu/Al composite wires have been widely used in cable industry. Especially in the development of aerospace, the light weight character of wires is particularly important. The wires are fabricated by a drawing process and heat treatment. Mechanical and electrical properties are measured and analyzed. The bending behavior is studied by scanning electron microscope. INTRODUCTION Cu/Al composite is a typical bimetallic composite that has been used in plenty of fields such as automobile and aerospace. The composite has the advantages of excellent conductivity as well as low weight, which cannot be obtained from single copper or aluminum. Industrial products of Cu/Al composite include Cu/Al composite joints (Uscinowicz, R., 2013), Cu/Al bimetallic sheets (Li, X. et al., 2011), Cu/Al flat bar (Wu, Y. & Liu, X. & Xie, J., 2014) and CCA wires (Ahmed N., 1978). CCA wires refer to the composite wires that copper layer concentrically coated on the surface of aluminum core conductor, implementing solid combination of two metals on the interface and forming an integral. At present, the aircraft cable generally use copper or copper alloy conductor, which makes the wire in the aircraft occupy a considerable proportion due to the large density of copper. Therefore, the use of Cu/Al composite wires instead of copper wires for weight loss, is of great significance to the development of aerospace technology industry. Heat treatment is an indispensable procedure to improve plasticity during cold working process, which is of great importance to preparation of wires (Wang, Q. et al., 2008). During the heat treatment, the Intermetallic Compounds (IMCs) are inevitable formed at the contact area of Cu/Al due to the occurrence of diffusion (Lee, S. et al., 2012). According to the results of former researchers, kinds of IMCs were discovered. Antoine Gueydan (2014) identified the formation of three IMCs (Al2Cu, AlCu, and Al4Cu9) at the interface between copper and aluminum after thermal aging. IMCs have a significant effect to the properties of Cu/Al wires. Bending performance is a vital property for the actual application of wires. The brittle IMCs may create a stress concentration that can cause crack initiation during bending process. This work focus on the mechanical properties of Cu/Al composite wires after heat treatment. The effect of various annealing condition on mechanical and electrical properties are studied, in order to find the appropriate annealing conditions, which produce optimal combination properties of Cu/Al clad composite wires. Bending fracture of composite wires is discussed by morphology observation.

Jan 1, 2019

By C. H. Hopper, D. R. Derry, H. S. McGowan

"The property of Matachewan Consolidated Mines is in the Matachewan area on the west side of Montreal river. It lies in the western extension of the Kirkland Lake sedimentary belt. The first discovery of gold on the property was made by S. Otisse, in 1916. The property was taken over by Ventures, Limited, in 1933 and production commenced in late 1934. To date (December 31st, 1947) it has amounted to 2,308,800 tons, from which gold and silver to the value of $9,567,600 has been recovered. The mill is currently treating 650 tons of ore a day.GENERAL GEOLOGYThe deposits lie close to the south contact of a belt of sediments striking in a general east-west direction. The sediments, presumed to be of Timiskaming age, consist of light buff arkose and greywacke, containing small pebbles. The Keewatin volcanic rocks to the south are andesites or basalts with cuff and agglomerate bands developed especially near the contact with the sediments. The lavas and sediments are overlain by relatively flat-lying sediments of the Cobalt series to the south and west of the mine, but these later sediments are not involved in the mineralization under discussion. The Keewatin lavas and Timiskaming sediments are intruded by dykes and lenses of red syenite porphyry that have approximately the same strike and dip as the invaded rocks. Later diabase dykes, apparently post-ore, run in a north-south direction and cut all rocks except the Cobalt series.OREBODIESThe gold-bearing mineralization forms bodies of two different types: (1) Within the volcanic rocks irregular orebodies with limited vertical extent. These consist of a series of flat-dipping quartz stringers and adjacent lavas and /or cuffs fractured, bleached, and mineralized with pyrite and gold. They are higher grade than the second type (average about 0.16 oz. gold a ton) and formed the main source of ore for the first 5 years of production. They are described in more detail than can be given here in an article by C. H. Hopper (4). More recent work on deeper levels has failed so far to find orebodies of comparable grade, though low-grade mineralization of a similar type does occur on the projected rake of the main group of the 'basalt type' of orebodies."

Jan 1, 1954

By D. J. Farmer

Mining hoists are major components of any underground mine, however, the detailed design work required to get the actual power required for a particular hoist is outside the scope of preliminary feasibility studies. Nonetheless, a hoist is costly. Therefore, an accurate estimate is needed for the design parameters and the power required. There are two methods available, namely, the O’Hara method and the Society of Mining Engineers’ method. Tests were done for both methods employing nine friction hoists and 19 drum hoists currently in use at Canadian mines. The O’Hara method provided unacceptable results for both friction and drum hoists. While, the SME method was designed for American regulations and factors of safety which often differ significantly from Canadian ones, good results were obtained. The two relationships deter-mined were simply to add 5% to friction hoist design and to add 4% to drum hoist design. Modifying the SME method by these two factors will allow the hoisting system determined by the SME method to be within the error for a prefeasibility study.

Jan 1, 1997

By Atsuki Sado, Akira Ueno, Kazuaki Takebayashi, Kunio Watanabe

The Saganoseki Refinery of Pan Pacific Copper Co., Ltd., Japan, introduced the ISA 2000® process in 2006 to improve product quality and productivity. After resolving various technical difficulties associated with the process, a current density of 325 A/m2 and electrolytic copper production of 234 000 tons per year were realized in 2018. In recent years, Saganoseki Smelter & Refinery has promoted treatment of recycled materials in addition to copper concentrates. Accordingly, the amount and type of impurities charged to the smelting process have tended to increase. In the electrorefining process, impurities such as nickel and antimony cause anodic passivation and formation of suspended solids, respectively. Although these undesirable phenomena can be avoided by controlling impurity concentrations in the anode and electrolyte to appropriate ranges, this also limits the choice of recycled materials that can be processed by the smelter. To achieve both stable operation of the electrorefining process and flexibility in treatment of recycled materials in the smelting process, Saganoseki Refinery improved the capacity of the impurity recovery processes during 2016 to 2018. This paper describes the expansion of the purification plant to remove and recover nickel and antimony. INTRODUCTION The Saganoseki Refinery of Pan Pacific Copper Co., Ltd., Japan, introduced the ISA 2000® (wax- less permanent cathode method) in 2006 to improve product quality and productivity. Since then, the refinery has gradually increased current density, and has been committed to establishing stable operation and high productivity via various improvements related to the electrolyte filtration and additive management systems. Figure 1 shows the trends of current density and current efficiency at the refinery. Although the current efficiency temporarily dropped when the current density was raised to 322 A/m2, it consistently exceeded 97% thereafter. At present, stable operation at 325 A/m2 has been achieved and continues.

Jan 1, 2019

By M. E. Wilson, A. C. Lee

"The property owned by Senator-Rouyn Mines, Limited, is in Rouyn township about 17'2 miles southwest of the town of Rouyn. It adjoins the Chadbourne claims of Noranda Mines, Limited, on the south and the Bagamac property on the ·west. It includes seven claims-block 44, blocks 80 to 83 and blocks 96 and 97; the mine is wholly in blocks 44 and 82.Late in 1936 gold was discovered in an outcrop of rusty weathering carbonate rock near the north end of block 44, and the following year the present Company was organized to proceed with the development of the property. During 1937-38, 17,000 feet of diamond drill core were bored to determine the extent of the ore deposit at depth. From October 15th, 1940, to April 15th, 1941, the ore was hauled to the mill at the Arntfield mine for treatment. The mill on the Senator-Rouyn property started on April 25th, 1941, and has been in practically continuous operation since than time. To the end of 1946, 574,874 tons of ore, from which gold having a value of $3,836,450 was recovered, were treated in the mill.GEOLOGYThe rocks exposed at the Senator-Rouyn mine, except in the southern part of the property, are almost wholly quartz diorite, part of an irregular mass that extends west from the town of Rouyn along the north shore of Noranda lake and thence southwest across the Senator-Rouyn claims. In the northern part of the propertyt inclusions of rhyolite occur here and there in the diorite. In the southern part the predominant rock is dacite and in the east-central part of block 44 claim andesite. Dykes of andesite, quartz syenite, and later diabase also occur on the property.The andesite of the Abitibi volcanics is not exposed on the property, but has been intersected in three diamond drill holes, one on the eastern boundary of block 44 and two farther west within the block. This andesite is probably the western end of a band of pillowed andesite well exposed in the Larose claim to the east."

Jan 1, 1954

By C. Dupuis, P. Waite, S. Leboeuf

Casthouses throughout the aluminium industry commonly use chlorine gas as a fluxing agent for furnace and in-line treatment of molten aluminium alloys. Its positive impact on the removal of alkali elements and non-metallic inclusions is well known. Nevertheless, the elimination of its use is highly desirable due to the safety and environmental risks associated with storage and handling. Over the past decade, the aluminium industry has significantly reduced its chlorine consumption. This has been achieved by maximizing the chlorine gas utilization efficiency during metal processing, and by the chlorine replacement for crucible and furnace metal treatment applications. Operation of sealed in-line treatment units without chlorine is now possible, but with lower or inconsistent removal efficiency penalties for alkali and inclusions respectively. This paper reviews the progress made at Arvida Research and Development Centre regarding the reduction of chlorine and the development of an alternative to chlorine for in-line metal treatment without penalizing the metallurgical performance.

Jan 1, 2006

By Jared Onyirimba, Jim Viellenave, Hal Demuth, Dale Verran, Chad Sorba, Errol Lawrence, David Bronkhorst

As outlined within the Denison Mines Corp’s (“Denison”) Pre-Feasibility Study ("PFS") completed in late 2018, additional work is required to increase confidence and reduce risk associated with the application of the In-Situ Recovery (“ISR”) mining method at the Phoenix deposit, located on the Wheeler River Uranium Project (“Wheeler River” or the “Project”) in northern Saskatchewan. The successful application of ISR in any geological environment largely hinges on three fundamental requirements, 1) permeability (of the deposit), 2) containment (of the mining solution) and 3) leachability (of the mineralization). Denison has designed several staged technical programs to progressively reduce risk associated with these requirements as the Company advances the Project toward a Feasibility Study (“FS”) and Environmental Impact Assessment (“EIA”). This paper will discuss the scope and results of certain technical programs being undertaken as the Company aims to develop the first ISR mining operation in the Athabasca Basin.

Jan 1, 2020

By P. G. West-Sells

At Barrick's Zaldivar Copper Mine in Chile, the addition of sulfuric acid to the ore going to heap leaching is a major expense. A process in which a portion of this acid is replaced by elemental sulfur added to the heap has been developed by Barrick and Westcoast Biotech that has the potential for significant cost savings. Initial shake flask tests with plant raffinate solution indicated that oxidation of elemental sulfur by a culture of sulfur-oxidizing bacteria, some indigenous to the Zaldivar heap, showed a significant lag period. This lag period could be reduced by dilution of the raffinate, but dilution would not be economical to implement at Zaldivar. Short (0.75 m) column tests indicated that after the initial lag period, sulfur biooxidation occurred steadily and the acid requirement for obtaining the same copper recovery as the control without sulfur was reduced by as much as 13 kg/t. These tests were followed by taller (5.1 m) column tests that confirmed the reduction in acid consumption, with no negative effect on copper extraction.

Jan 1, 2007

By M. Ye. Shulgina, M. L. Bolotin, S. A. Prokopev, Ye. S. Prokopev

Iron ores concentration at Russia’s operations is carried out using conventional flow sheets. They comprise the two-four stage grinding followed by one-two stage magnetic separation. This results in the maximum recovery of magnetite to concentrate and the tailings generation. The final concentrate is generated only during the last stage of magnetic separation. Technologically, this flow sheet layout is not effective at recovering the liberated magnetite grains during grinding to the resulting concentrate. Advanced models of magnetic separators do not allow for the selective separation of the tailings and the portion of the resulting iron ore concentrate. Magnetic product which is the ore mixture of the liberated magnetite grains, high grade and low grade intergrowths is directed to the next grinding stage. In this case, regrinding of the liberated magnetite occurs. In addition, the performance of hydrocyclones during classification in closed grinding circuits is poor. Their classification efficiency does not provide the material separation in accordance with the size. In this case, simultaneous separation in accordance with the density occurs. The quartz particles with the size of 300 mm have similar velocity and trajectory like the particles of magnetite with the size of 60 mm. As a result, light and coarser intergrowths report to the overflow and free heavy magnetite grains report to underflow and return to regrinding (“the density effect”). This resulted in a significant increase of a mill circulating load, the decrease in the feed throughput and higher power consumption. In this connection, the development of iron ore concentrate stage recovery with the focus on gradual liberation of the intergrowths is getting much attention. Gravity concentration technique, particularly, spiral separation is effective at solving the problem of stage recovery not only the dump waste product but also high grade magnetite concentrates at the early concentration stages. This can be attributed to a significant difference in magnetite (4.9-5.2 g/cm3) and host minerals (quartz 2.7 g/cm3) densities, which is the principal during gravity concentration. The test work on concentration of various products samples from current operations (the mills discharges, concentrates from various stages of wet magnetic separation and cyclones underflows) was carried out. Spiral separators SV-500 and ShV-500 manufactured by Spirit LLC were used for the test work. High grade iron ore concentrate (69.05% Fe) was generated during primary wet magnetic separation concentrate concentration using a spiral separator. During the concentration of mills discharges the content of iron in the resulting concentrates and middlings of wet magnetic separation II stage was 64.5% and 64.6%, respectively. The recovery of iron to the concentrates of spiral separation was 33.6-42.0%. The studies presented demonstrate that by using spiral separation for iron-bearing ores concentration, you can separate magnetite liberated grains at the early concentration stages, decrease their regrinding and circulating loads in grinding circuits. This process is able to improve the overall recovery and economics of iron ores concentration process.

Jan 1, 2016

By M. Ye. Shulgina, M. L. Bolotin, S. A. Prokopev, Ye. S. Prokopev

Iron ores concentration at Russia’s operations is carried out using conventional flow sheets. They comprise the two-four stage grinding followed by one-two stage magnetic separation. This results in the maximum recovery of magnetite to concentrate and the tailings generation. The final concentrate is generated only during the last stage of magnetic separation. Technologically, this flow sheet layout is not effective at recovering the liberated magnetite grains during grinding to the resulting concentrate. Advanced models of magnetic separators do not allow for the selective separation of the tailings and the portion of the resulting iron ore concentrate. Magnetic product which is the ore mixture of the liberated magnetite grains, high grade and low grade intergrowths is directed to the next grinding stage. In this case, regrinding of the liberated magnetite occurs. In addition, the performance of hydrocyclones during classification in closed grinding circuits is poor. Their classification efficiency does not provide the material separation in accordance with the size. In this case, simultaneous separation in accordance with the density occurs. The quartz particles with the size of 300 mm have similar velocity and trajectory like the particles of magnetite with the size of 60 mm. As a result, light and coarser intergrowths report to the overflow and free heavy magnetite grains report to underflow and return to regrinding (“the density effect”). This resulted in a significant increase of a mill circulating load, the decrease in the feed throughput and higher power consumption. In this connection, the development of iron ore concentrate stage recovery with the focus on gradual liberation of the intergrowths is getting much attention. Gravity concentration technique, particularly, spiral separation is effective at solving the problem of stage recovery not only the dump waste product but also high grade magnetite concentrates at the early concentration stages. This can be attributed to a significant difference in magnetite (4.9-5.2 g/cm3) and host minerals (quartz 2.7 g/cm3) densities, which is the principal during gravity concentration. The test work on concentration of various products samples from current operations (the mills discharges, concentrates from various stages of wet magnetic separation and cyclones underflows) was carried out. Spiral separators SV- 500 and ShV-500 manufactured by Spirit LLC were used for the test work. High grade iron ore concentrate (69.05% Fe) was generated during primary wet magnetic separation concentrate concentration using a spiral separator. During the concentration of mills discharges the content of iron in the resulting concentrates and middlings of wet magnetic separation II stage was 64.5% and 64.6%, respectively. The recovery of iron to the concentrates of spiral separation was 33.6-42.0%. The studies presented demonstrate that by using spiral separation for iron-bearing ores concentration, you can separate magnetite liberated grains at the early concentration stages, decrease their regrinding and circulating loads in grinding circuits. This process is able to improve the overall recovery and economics of iron ores concentration process.

Jan 1, 2016

By Kostas Fytas

Acid mine drainage (AMD) is a serious environmental problem that preoccupies the Canadian Mining Industry. Considerable amounts of money are spent every year in an effort to prevent or reduce the acid mine drainage phenomenon. AMD occurs when sulphide minerals (ex. pyrite) contained in rock are exposed to air and water and subsequently oxidize to produce low pH water. This acid effluent has the potential to mobilize any heavy metals contained in the rock. Coating the sulphide minerals with silicates is a new promising technology to reduce AMD. Pyrite is treated with a solution containing H2O2, sodium silicate and a buffering agent. H2O2 oxidizes a small part of pyrite producing ferric iron (Fe3+) ions. These ions subsequently react with the silicate ions to produce ferric hydroxide-silica that precipitates on the pyrite surface producing a passive coating. This silicate coating can protect the grains of pyrite from oxidation. This paper presents a series of experiments that confirm that silicate coating can considerably reduce AMD.

May 1, 2001

By M. Aushouri, S. H. Mansouri, N. Aminizadeh

A thermo-chemical model of the Peirce-Smith copper converter in blowing the copper stage has been developed to predict the molten temperature. The key assumption of the model was that white metal and gas phases in the converter were in thermal and chemical equilibrium. In this model, the chemical reaction of white metal and oxygen was accomplished completely. So long as sulfur existed in the bath, the generation of Cu2O was frozen. The reaction rate was considered to be constant and controlled by the reacted sulfur. The converter temperature was calculated by heat balances over time. The model was validated by a detailed comparison with measured industrial data. A good agreement was obtained. The converter temperature depended on process parameters such as oxygen efficiency, molten emissivity and oxygen enrichment.

Jan 1, 2007

By L. Haavanlammi

The Outokumpu HydroCopper® process is a chloride based atmospheric leaching process alternative that can treat a variety of different concentrates. Chalcopyrite and other copper sulfides can effectively be leached under atmospheric pressure in strong, aggressive chloride solution using copper (II) ions as oxidant. Impurities are removed from the solution as carbonates and ion exchange. Copper is precipitated from the purified pregnant leach solution as copper (I) oxide, which is filtered and reduced by hydrogen gas to metallic copper powder, which is melted and cast into copper product. Sodium chloride solution from copper (I) oxide precipitation is decomposed in a chloralkali electrolyser, to products of which are circulated back to the process. The process has been designed for copper concentrates and is a fast and economical way to produce copper wire rod directly from concentrate. The process can efficiently handle impurities like arsenic and mercury, which can be harmful in the pyrometallurgical processes. The process has been tested in the laboratory and 1 ton/day demonstration plant scale and it has been proven to be commercially viable. The process has been designed to meet the strictest directives for emissions. Other environmental factors are carefully considered to obtain the highest possible eco-efficiency.

Jan 1, 2007

By Samuel O. Akande

"Gold occurs as native metal, in electrum, and in a telluride mineral in quartz carbonate veinlets of three vein systems at the Ross Mine, northern Ontario. The 14 Vein System is made up predominantly of concordant veinlets within layered ankeritic dolomite stratabound by, and conformable with, andesite tuff Individual veinlets contain pyrite, sphalerite, galena, chalcopyrite, tennantite, pearceite, proustite, native gold and electrum in a matrix of quartz, dolomite, ankerite and calcite. The 2B Vein System is made up of both concordant and discordant veinlets within andesite tuffs. The veinlets contain pyrite, chalcopyrite, sphalerite, bornite, tennantite and free gold in quartz, calcite and dolomite. The 18 Vein System is comprised of stockwork veinlets in and around intrusive syenite which has both sharp and gradational contacts with enclosing andesite tuff The veinlets contain pyrite, chalcopyrite, bornite, chalcocite, native gold and calaverite. Sulphide and silicate minerals in veinlets and wall rocks are stable assemblages for the regional metamorphism of greenschist rank. ,The 14 Vein System is interpreted as a metalliferous siliceous carbonate chemical sediment, the components of which were leached from the underlying volcanic rocks by convecting sea water and subsequently deposited on the sea floor between the extrusion of flows and pyroclastic rocks. Subsequent regional metamorphism and intrusions remobilized and redistributed the syngenetic stratabound material into dilatant fractures in adjacent tuff, as in the 2B and the 18 vein systems."

Jan 1, 1982

By E. P. Evoy, A. W. Jolliffe

"The Uranium deposit of Gunnar Mines, Limited, is on the south shore of Crackingstone peninsula in the Beaverlodge area of northern Saskatchewan.The ore consists of disseminated pitchblende and uranophane in brecciated syenite, and forms a tubular or pipelike body, outcropping at the surface and plunging southward at about 45 degrees for a known length of1,400 feet (see Figure I). The upper portion is being removed by open-pit mining to a depth of 300 feet below adjacent Lake Athabasca. The remainder will require underground mining methods (see Figure 2).The property was staked in July, I 952, and the orebody was subsequently defined by about 70,000 feet of diamond drilling. A 1,250-ton mill was completed in 1955, and production commenced in September of that year with ore from the open-pit operation. The mill is presently being increased to 1,650 tons capacity, and a three-compartment vertical shaft is being sunk to 1,250 feet in preparation for underground mining.GeologyThe mine property is underlain by an assemblage of Precambrian metasediments known locally as paragneiss, granite-gneiss, and syenite. These lie on the southeast limb of a southwest-plunging anticline, strike about north 75 degrees east, and dip southward at about 45 degrees. Para- gneiss outcrops in the northwestern half of the claim group, and again on the islands south of St. Mary's Channel. The granite-gneiss lies conform-ably within the paragneiss and makes up the southeastern part of the property. The syenite forms an irregular, triangular-shaped mass within, and near the footwall of, the granite-gneiss band. Small lenticular bodies of mafic rocks are also present, the former being most prevalent in the paragneiss.The granite-gneiss is coarse to medium-grained, pink to grey, well foliated, and composed of feldspar (65 per cent), quartz (20 per cent), chlorite, and minor mica. The general concordance of its contacts with paragneiss and the absence of intrusive relationships along these, the presence of uniformly oriented inclusions of obviously sedimentary origin within the granite-gneiss, and the variation in colour and texture across the strike all strongly suggest that this member represents a granitized sedimentary rock."

Jan 1, 1949

By Ramin ArameshAsl

Urumieh-Dokhtar is the well-known vast metallogenic belt extended from NW to SE of Iran and basically is referenced in copper mineralization studies in Iran. Hashtjin 1:100000 sheet (NW Iran) is located on this belt and rock units are consisted of Oligocene intrusive, volcanic rocks and Eocene Sedimentary rocks. Concerning the significance of identifying the alterations and faults zones in copper exploration, the aim of this study is identifying the copper mineralization by multi-spectral analysis of ASTER (Advanced Space borne, Thermal Emission and Reflection Radiometer) satellite images in the limitation SD-SWIR (Spectral Domain of Short Wave Infrared). Several analytical methods are implemented in this study such as SAM (Spectral Angle Mapper), MF (Matched Filtering) and PCA (Principal Components Analysis). These methods have been utilized for recognizing the Argillic, Propylitic and Sericitic alteration zones and all of them are relying on the remote sensing methods as well as geological studies of new targets for copper mineralization identification in the area.

Aug 1, 2013

By Y. Chunhua, L. Chunsheng, W. Sheng

"Countercurrent solvent extraction is the dominant industrial rare earth separation method. For the rare earth separation, with low separation factors and multiple components, designing and optimization plays an important role in reaching product quality and reducing separation plant costs. Based on the theory of countercurrent extraction, cost-efficient methods, such as third-outlet separation and hyperlinked extraction processing, have been introduced following computer simulation. The consumption and fixed investment of industrial practice are compared, by which advantages of the optimized rare earth separation process are indicated. INTRODUCTIONThe rare earths (RE) have outstanding optical, magnetic and electric properties in advanced material applications and have therefore received much international attention in recent years. Liquid-liquid extraction is the major industrial RE separation method and is widely used in the industry. Supported by the government and with collaboration from the institutions and enterprises, China has made great progress in RE separation, and has become the dominant supplier of separated RE products. Complicated by multiple elements and low separation factors, careful design of RE separation processes is vital for the quality and cost of production. The theory of separation is the key to basic of flowsheet design and industrial applications.BASIC SEPARATION PROCESS AND THEORYGeneral ProcessAcidic extractants such as P507, P204 and naphthenic acid, are the most popular extractants in modern RE separation industry. In the general separating process, the extractant is saponified with a base, then ion-exchanged with RE solutions, thereby to provide stable and high RE loading in the extractant to fulfill the requirement of production quantity and quality. The RE-loaded extractant is then countercurrently extracted and scrubbed with RE solutions and the RE element thereby is purified. After the countercurrent extraction process, the RE-loaded extractant is stripped with acid to obtain an aqueous RE product, and prepare the extractant for recycling (Xu, 1995)."

Jan 1, 2012

By M. Tanaka, H. Narita, K. Morisaku

"The selective separation of palladium (Pd), platinum (Pt), and rhodium (Rh) from a hydrochloric acid solution by solvent extraction was investigated using amide-type extractants, i.e., N,N,N’,N’-tetra-n-octyl-thiodiglycolamide (TDGA) and N-n-hexyl-bis(N-methyl-N-n-octyl-ethylamide) amine (BisAA). The separation experiments employed two separation schemes: (1) extraction of Pd with TDGA and that of Rh and Pt with BisAA; and (2) extraction of Rh, Pd, and Pt with BisAA. Separation scheme 1 achieved the highly selective separation of each metal. For separation scheme 2, Rh can be recovered prior to Pd and Pt, despite having a lower selectivity for Pd/Pt than separation scheme 1. INTRODUCTIONThe recent increase in the use of platinum group metals (PGMs) in industry (especially auto catalysts containing palladium (Pd), platinum (Pt), and rhodium (Rh)) has lead to their increasing waste; therefore, improvements in the recovery techniques for PGM have received significant attention. In metal refineries, PGMs are mainly separated and purified by solvent extraction (Cox, 2004). The extraction process used in INCO’s Acton precious metal refinery is one of the most famous commercial processes and is utilized worldwide. In this process, silver is first removed as a residue (AgCl), and then gold, Pd and Pt are extracted from hydrochloric acid (HCl) solutions using dibutylcarbitol (DBC), dialkylsulfide (DAS), and tri-n-butylphosphate (TBP), respectively. Finally, Rh remains in the raffinate (Barns & Edwards, 1982).The development of a successful solvent extraction process depends on the choice of the appropriate extractants. We have studied the extraction of PGM using N,N-disubstituted amide compounds (Narita, Tanaka, Morisaku, & Abe, 2004; Narita, Tanaka, Morisaku, & Tamura, 2006; Narita, Tanaka, & Morisaku, 2008a, 2008b). They are relatively stable against acids, and their metal extractability can be improved by changing the side chain length and/or introducing additional donor atoms like sulfur and nitrogen. We have recently found that thiodiglycolamide and an amide-containing tertiary amine have good extractabilities for Pd and Rh, respectively."

Jan 1, 2012

By Saeid Akhavan

Accumulative roll bonding (ARB) is a severe plastic deformation process for achieving ultrafine grains in metallic sheets without changing the sample dimensions. In this study, ARB process was carried out on 5083 aluminum alloy sheets up to 6 cycles. In this process, the surfaces of the strips to be joined are roughened and cleaned and then stacked. After stacking, the specimen is roll-bonded by rolling using a 50% reduction. The rolled specimen is cut into two halves, and the above-mentioned procedure is repeated for several times. Microstructural characterizations were analyzed by transmition electron microscopy (TEM). Tension and Vickers hardness tests were performed on produced sheets for evaluating their mechanical properties. In order to clarify the failure mode, fracture surfaces after tensile tests were observed by scanning electron microscopy (SEM). The results indicated that at the early stages of ARB process, grains were subdivided by deformation induced boundaries. After several ARB cycles, lamellar structure elongated in the rolling direction contains lamellar boundaries was formed. With increasing the strain, mean spacing of lamellar boundaries decreased. Finally, continuous recrystallization resulted in a microstructure covered with small recrystallized grains with an average diameter below 100 nm at the end of four cycle. The tensile strength and hardness of the 6 cycle ARB processed 5083 aluminum alloy sheet increased about two and three times of the initial values, respectively. Results indicated conformity between mechanical evolutions and microstructural changes during ARB process. Fracture surfaces observations showed that failure mode in ARB processed aluminum is shear ductile rupture with elongated small dimples.

Oct 1, 2011