Search Documents

By C. E. Lesher

Low-TEMPERATURE carbonization needs no introduction to the literature on coal. This paper will attempt no review of that literature; it tells the story of the commercial development of one of the processes for carbonizing coal at so-called low temperatures, dealing with the technology and economics of the process rather than with the design of equipment. The process used is that covered by the patents of C. B. Wisner, with improvements and changes made by the Pittsburgh Coal Carbonization Co. The important and novel feature of the process is the phenomenon of making the product in ball form (Fig. 1). Melting coal dust into smokeless solid fuel in an apparatus as simple as a revolving cylinder of ordinary mild steel has been proved to be practical. Furthermore, it has been found that the process has a wide application, for by applying a knowledge of why and how this balling action is accomplished, the apparatus can be designed and adapted to treat any coal that has a certain minimum agglutinating property. The operating plant is 20 miles west of Pittsburgh, adjacent to the Champion preparation plant of the Pittsburgh Coal Co. The coal used is cleaned minus 3/8 -in- or finer sizes. The products are low-tem-perature coke, tar and tar products. Present capacity is 7000 tons per month of low-temperature coke and 140,000 gal, of tar. There is no surplus gas for sale, and none of the light oils are stripped from the gas. The coke is marketed in two sizes, 1 to 2 in. and 1 to 6 in., through retail coal dealers for domestic con-sumption in hand-fired furnaces, and for fireplace fuel. The smaller size is bagged by dealers. Crude tar and many distillates and road tars are sold.

Jan 1, 1940

ALABAMA Altoona -Cain, J Anniston -Cowie, L K Heimrod, A A White, H E Bessemer-Abbott, C C Ball, E M Mitchell, F R Thompson, N E Birmingham -Adler, T E Aldrich T H Aldrich, T H, Jr Blackburn, A R Bush, 117 W Clark, G H Cowin, P G Crane, W R Crawford, G G Crockard, F H Darnelspn, G E Davis, C B

Jan 1, 1923

Jan 1, 1920

By W. Mitchell, B. H. Bergstorm, C. L. Sollenberger

A unique compression testing machine was constructed to load individual 1/8 to I-in. spheres of glass, etc., at rates from 100 to 100,000 lb per min. During loading the applied load was continuously plotted us the deformation of the sphere-platen system. The load-deformation curve conforms to the theory of elasticity. The spheres were surrounded by steel retaining rings or by gelatin (to prevent secondary fracture). The product size modulus was determined from screen analyses. The data shows: 1) Energy input per unit mass is inversely proportional to the product size modulus (or directly proportional to the surface area per unit mass). 2) Increased loading rates slightly increase the energy input per unit mass required for fracture without affecting the preceding relationship. Theory and experiments show that much of the input strain energy is transformed into kinetic energy of fragments at fracture, this being a reason efficiencies based on "surface energies" are exceedingly small. This large kinetic energy component is usually dissipated as heat but may be partially reclaimed because impact of fragments against the surface of steel retaining rings causes additional comminution. There are currently several theories of crushing, all of which can be derived from the general energy equation of Gillilandl as was pointed out by Mitchellet al in 1954'and more recently by Rose and Sullivan. If the exponent of the equation dE-x-"dx is assigned values of 2,1, or 3/2, one obtains by intergration between suitable limits, the equations of Rittinger, kick,' and Bond,' respectively. Other investigators prefer to let the exponent be a variable parameter. To help resolve the controversy, the Allis-Chal-mers Research Laboratories set up a series of carefully controlled experiments in which the level of energy input required to induce the comminution of a single particle by slow compression loading was very accurately measured. The energy input requirement, in conjunction with the size analysis of the fragments produced at fracture, yielded an accurate energy-product size relationship for the conditions studied. APPARATUS The experimental apparatus was designed to apply a compressive load on opposite sides of an "ideal particle." Spherical shapes were chosen, because point contact loading is typical of the mechanics of conventional crushers. The bulk of the experimental data was obtained with glass spheres because glass is a fairly homogeneous, brittle material for which the properties follow definite statistical distributions. The spheres ranged from 1/8 to 1-in. diam. The compressive load was applied to the specimen at a uniform rate by a loading mechanism (Fig. 1) which acted through a system of levers. The uniform rates, ranging from 100 to 100,000 lb per min, were obtained by metering water into a bucket suspended at the end of the secondary level. Point contact was made with the sphere through tungsten-carbide platens. This latter material is extremely hard and has a high modulus of elasticity, thereby having a minimum of distortion when loaded. The actual load on the sphere was measured independently of the lever system by a load cell, Fig. 2, which was designed so that the voltage output of the load cell would be proportional to load. The deformation of the specimen was indirectly measured by a pair of transformers which were attached to opposite edges of the upper platen. The cores of the transformers, which were attached to the lower platen, moved relative to the transformer so that the voltage output was proportional to the deformation of the sphere-platen system. The load was plotted against the deformation on an X-Y recorder. The area under the curve, as shown on Fig. 3, was proportional to the energy input of the

Jan 1, 1961

By G. Ostberg

OXYGEN has frequently been considered responsible for phenomena in the metallurgy of cast iron which are not sufficiently explained by the presence of other elements. Oxygen and oxides have been regarded as critical factors, particularly for the solidification process, and specifically in the formation of graphite. However, the evidence for an influence of oxygen has mostly only been indirect or qualitative. Furthermore, quantitative data on the oxygen content of cast iron presented in the literature have often been less conclusive as being apparently determined with insufficient regard for the difficulties associated with the sampling and analysis. These problems, experimental and theoretical, have been studied in this investigation. An attempt is made to bring the views on the soluble amount of oxygen in cast iron on a level with the present understanding of the thermodynamics of these types of alloys. Although there are no experimental data on the complete multicomponent cast-iron alloys some conclusions have been drawn from investigations on simpler systems. The order of magnitude of the solubility of oxygen in cast iron is considered in the first part of the paper. The second part deals with the oxygen content actually present under practical conditions. First the possible sources of errors in sampling and analyzing methods are examined. Finally some observations on the oxygen and oxide content of malleable iron during the production process are made. THERMODYNAMICS OF OXYGEN SOLUBILITY When cast iron is saturated with oxygen the saturation phase is essentially carbon monoxide or silicon dioxide depending upon the composition of the iron, the temperature, and the rates of formation of the oxides.* The latter occurs accordiw to the O + C = CO, Kc0 - a COa J 20 + Si = SiO2, Activities are used here instead of weight pct concentrations, since activities are believed to show more sensitively the effects of the interaction of all the alloying elements. Calculations involving activities are, however, seriously hampered by lack of experimental data on the interactions between the components encountered in the multi component cast-iron system Fe-O-C-Si-Mn-P-S- and so on. In order to make an estimate of the oxygen solubility reason-

Jan 1, 1959

By M. Gell, G. R. Leveran

The high- and low-cycle fatigue properties of the nickel-base superalloy, Mar-MBOO, in columnar-grained and single-crystal forms were determined at room temperature. It was found that the fatigue lives of these materials were greatly affected by the size of preexisting cracks in MC-type carbides contained in the micro structure. Most of the data falls on two curves given by: (zN)'/A€= K, where Nf is the number of cycles to failure, Af is the total strain range, and K is a function of carbide size. No difference was observed in the fatigue behavior of the columnar-grained and single-crystal materials for the same MC carbide size. Matrix slip and crack initiation occurred at precracked MC carbides and, to a lesser extent, at micropores. Fatigue crack propagation was mainly in the Stage I mode, i.e., on cry stallo graPhic slip planes. The Stage I fracture in these materials was unusual in that distinct features were observed on the fracture surfaces. In high-cycle fatigue, these features resembled those commonly observed on the cleavage fracture surfaces of bcc and hcp materials. Yet, in this study, the cracks propagated slowly in a cyclic manner. In low-cycle fatigue, the Stage I facets contained equiaxed dimples, similar to those observed on the tensile fracture surfaces of ductile materials. These observations indicate that both local normal and shear stresses are involved in these Stage I fractures. A model is proposed to explain these results based on the weakening of the cohesive energy of the active slip planes by reversed shear deformation and the fracture of the bonds across the weakened planes by the local normal stress. RECENT developments in casting technology have produced cast nickel-base superalloys in columnar -grained and single-crystal forms.1'2 The tensile and creep properties of the nickel-base superalloy, Mar-M200, cast in these forms have been shown to be superior to the corresponding properties of the conventionally cast polycrystalline material.lp2 This improvement in properties results, in part, from the elimination of grain boundaries in the single crystals and the alignment of the grain boundaries parallel to the stress axis in the columnar-grained castings. As part of a program to evaluate the fatigue properties of nickel-base superalloys cast in single-crystal and columnar-grained forms, a study has been made of the cyclic deformation and fracture of Mar-M2OO at room temperature. M. fiFl I .hininr Mpmher AIMF ic ^pninr Rocoarrh Accn^iata anH I) EXPERIMENTAL PROCEDURE The composition range of Mar-Ma00 in weight percent is: 8 to 10 Cr, 9 to 11 Co, 11.5 to 13.5 W, 0.75 to 1.25 Cb, 1.75 to 2.25 Ti, 4.75 to 5.25 Al, 0.01 to 0.02 B, 0.03 to 0.08 Zr, 0.07 to 0.12 C, bal. Ni. All of the castings met the above specifications. The castings were solutionized for 1 to 4 hr at 2250°F followed by aging at 1600°F for 32 hr which resulted in a 0.2 pct offset yield stress of 150,000 psi at room temperature. The microstructure of the material consisted of cuboidal, coherent particles of ordered, fcc Ni3(A1,Ti) (commonly designated y'), approximately 0.3 p on edge, distributed in an fcc y solid-solution matrix. MC carbides together with shrinkage and gas micropores were also distributed throughout the materials. The MC carbides and micropores were located preferentially in the interdendritic interstices, as well as in the grain boundaries in the columnar-grained castings. The (100) direction of all the single crystals and the common (100) axis of the grains in the columnar materials were aligned within about 5 deg of the specimen axis. Fatigue testing was carried out in the high-cycle (HCF) and low-cycle (LCF) fatigue regions, with the major difference being gross yielding of the specimen occurred during the first cycle in the LCF region. This division also corresponded with the more usual one in which the life of a specimen in LCF is less than lo4 cycles and that in HCF is greater than lo4 cycles. The designs of the high-cycle fatigue and low-cycle fatigue specimens are shown in Figs. l(a) and (c), respectively. The gage sections of both HCF and LCF specimens were electropolished prior to testing. The HCF specimens were tested in an MTS, closed-loop, hydraulic fatigue machine at 10 cps in air. The specimens were cycled between a tensile stress of 5000 psi and a maximum tensile stress which ranged from 35,000 to 125,000 psi, Fig. l(b). The LCF specimens were cycled under strain control from zero to a maximum tensile strain, Fig. l(d), in a Wiedemann-Baldwin testing machine. The experimental procedure has been described elsewhere.3'4 Both HCF and LCF tests were interrupted periodically in order to replicate the development of slip and cracking at the specimen surface. This was accomplished by placing plastic replicating tape around the gage section of the specimen while the specimen was in the mahine. The size of the MC carbides for all specimens was measured on a polished longitudinal section through the gage section after fatigue testing. The method of measurement consisted of carefully scanning the entire polished section in order to locate the largest MC carbides. Photographs were then taken of the six longest carbides oriented approximately normal to the

Jan 1, 1969

By C.A. Zapffe

Both the foundryman and the theoretical metallurgist are now generally agreed that the anomalous "rising" or "bleeding" of certain ferrous castings of killed metal is primarily attributable to hydrogen. How and why the phenomenon occurs, however, have not been made clear. The following discussion is intended to harmonize foundry experience with metallurgical theory so that the foundryman may possibly improve his ability to prognosticate whether a certain casting may bleed or not. Bleeding, Rising, and Piping The "rising" to be discussed here is not to be confused with the action in rimming ingots as a result of the carbon-oxygen reaction, although a conclusion will be drawn that may apply to the art of controlling the rimming action. Only killed metal is considered, which includes both steels and irons. In Fig. I, three killed, chill-cast ingots are shown: a porous ingot whose evolution of gas during late stages of solidification has ejected metal through the top; an ingot in which moderate gas evolution during solidification has lifted the mushy central metal, i.e., it has "risen"; and, third, a sound ingot with good piping characteristics. The first type is referred to as "bleeding," and generally infers that a solid skin had first formed through which the liquid metal later erupted. There is no fundamental distinc- tion between bleeding and rising in reference to killed metal.* Porosity Hydrogen appears as a cause of bleeding because the gas evolution simultaneously leaves a porosity of a type traceable to hydrogen. Twenty years ago, Melmoth' noted that killed steel that rose unexpectedly in the mold, if returned while liquid to the furnace and heated further under a reducing lime slag, would again rise in the mold; but that if the ingot were allowed to solidify and was then remelted no rising occurred. A critical quantity of the responsible gas is therefore removed by the rising action. Melmoth associated rising with high silicon (0.7 to 0.9 per cent) and concluded that silicon increased gas absorption. Because silicon is a strong deoxidizer, oxygen must, therefore, be eliminated from consideration of the three common gases in steel—oxygen, nitrogen, and hydrogen. Butterworth2 later decided that pinhole porosity was caused by gases dissolved in the metal and that hydrogen was obtained from steam in the mold. Allen's classical work on copper castings,3 soon followed by

Jan 1, 1943

By C. A. Zapffe

Both the foundryman and the theoretical metallurgist are now generally agreed that the anomalous "rising" or "bleeding" of certain ferrous castings of killed metal is primarily attributable to hydrogen. How and why the phenomenon occurs, however, have not been made clear. The following discussion is intended to harmonize foundry experience with metallurgical theory so that the foundryman may possibly improve his ability to prognosticate whether a certain casting may bleed or not. Bleeding, Rising, and Piping The "rising" to be discussed here is not to be confused with the action in rimming ingots as a result of the carbon-oxygen reaction, although a conclusion will be drawn that may apply to the art of controlling the rimming action. Only killed metal is considered, which includes both steels and irons. In Fig. I, three killed, chill-cast ingots are shown: a porous ingot whose evolution of gas during late stages of solidification has ejected metal through the top; an ingot in which moderate gas evolution during solidification has lifted the mushy central metal, i.e., it has "risen"; and, third, a sound ingot with good piping characteristics. The first type is referred to as "bleeding," and generally infers that a solid skin had first formed through which the liquid metal later erupted. There is no fundamental distinc- tion between bleeding and rising in reference to killed metal.* Porosity Hydrogen appears as a cause of bleeding because the gas evolution simultaneously leaves a porosity of a type traceable to hydrogen. Twenty years ago, Melmoth' noted that killed steel that rose unexpectedly in the mold, if returned while liquid to the furnace and heated further under a reducing lime slag, would again rise in the mold; but that if the ingot were allowed to solidify and was then remelted no rising occurred. A critical quantity of the responsible gas is therefore removed by the rising action. Melmoth associated rising with high silicon (0.7 to 0.9 per cent) and concluded that silicon increased gas absorption. Because silicon is a strong deoxidizer, oxygen must, therefore, be eliminated from consideration of the three common gases in steel—oxygen, nitrogen, and hydrogen. Butterworth2 later decided that pinhole porosity was caused by gases dissolved in the metal and that hydrogen was obtained from steam in the mold. Allen's classical work on copper castings,3 soon followed by

Jan 1, 1943

By S. Shapiro, J. A. Ford

The crystallo graphy of several grains of the lamellar Ni-Ni3 B eutectic solidified under conditions appvoachirt equilibriun has been examined.. A preferred interlace relationship has been observed in this system which may be described as: A detailed study of this interface by means of an atomistic model reveals the interface Plane to be puckered and more accurately describable as: Analysis of the atomic configuration on these planes reveals that this interface conforms to the orientation criteria proposed for directionally solidified lanzellar eutectics. In addition, a model is proposed to help explain the growth of a "puckered" interface. DURING the past several years an increasing number of unidirectional solidification experiments on eutectic alloys have been reported in the literature. The primary emphasis, in most cases, has been the effect of growth variables on microstructure. Some authors have, however, studied the crystallographic orientations and interfacial relationships resulting from these experiments. Four crystallographic studies have been published;'-4 in each of these there is a factor which tends to prohibit the extension of the observations beyond the particular system. In the Al-CuA12 system, the approximately equal volume fractions of the phases have resulted in sorrie controversy as to which phase constitutes the matrix. In the Mg-Mg,Sn eutectic the presence of several interconnecting lamellar systems2 complicates the analysis. The two remaining eutectics. 1nSb-b and Al-Ali, are both rodlike (the latter exhibits a plate morphology at low solidification rates): the matrix in each of these alloys is the simpler (fcc) phase. Studies of nucleation in eutectic alloys indicate that the more complex constituent is the nucleating -.phase.' For the purpose of an analysis of interface crystallography it was deemed desirable to study a lamellar system in which the matrix was the more complex and, presumably. the nucleating phase. Recently it has been shown that there is a eutectic in the Ni-B system between Ni3B and i; preliminary investigation by the authors indicated that the matrix in this eutectic is the boride phase. The structure of Ni,B is reported to be orthorhombic, the compound being isostructural with cementite. This eutectic is therefore analogous to that between austenite and cementite. Furthermore, the Ni-B system is not susceptible to a competing eutectic reaction as occurs in the Fe-C alloys; nor does it exhibit a eutectoid decomposition. For these reasons the study of the interfacial relationship in the Ni-Ni3B eutectic was undertaken. PROCEDURE Ingots of nominal composition 3.5 and 3.6 wt pct B were induction-melted in boron nitride crucibles within a graphite susceptor under a boric oxide slag; a dynamic argon atmosphere was maintained over the melt to prevent rapid oxidation of the susceptor. The raw materials used were 99.97 pct Ni from Huntington Metals Division of International Nickel Co. and 99.8+ pct B chips supplied by the United Mineral and Chemical Co. The analyses of the starting materials are listed in Table I. The melt was held at 1500cC for 2 hr to insure complete reaction and allowed to cool to room temperature. The castings were chemically analyzed for boron and were metallographically examined for uniformity. The metallographic samples were mechanically polished through 0.1 p A1,0, and etched with Carapella's reagent. Each master casting was cut up to make several specimen blanks which were remelted, in boron nitride crucibles, to form ingots of 1/2 to 3/4 in. in diarn by 7 in. long. These ingots were unidirectionally solidified using a modified vertical Bridgman technique. The rate of solidification was assumed to be equal to the uniform rate at which the crucible-susceptor assembly was withdrawn from the induction coil. This rate was varied from 1.18 to 2.21 cm per hr. In order to perform these experiments it was found necessary to redetermine the eutectic composition. This was accomplished by the zone-melting technique described by Yue and lark.' An ingot of 4.5 wt pct B was zone-melted in a horizontal boron nitride boat 7-1/2 in. long with a 112-in.-square cross section. A

Jan 1, 1967

THE primary interest in the subject of this chapter lies in the fact that various heats of steel made to the same chemical specification do not always-have the same properties. The properties considered here, of course, are those inherent in the ingot immediately after solidification and not qualities imparted by variations in subsequent mechanical or thermal treatment. The expression "made to the same chemical specification" is used because some of the variations in properties are due to variations in chemical analysis within the specified ranges of those elements commonly specified and determined. Other variations in properties are due to variations in those constituents of steel (elements or compounds) that are not ordinarily included among the elements specified, thus not a part of the specified "composition." The term "constitution" is used to include not only the specified composition but also the nature and distribution of every element or compound contained in the steel entering the ingot mold; also included are items such as aluminum oxides and nitrides, presence of soluble gases, and dispersion of nonmetallic particles. When it is considered that the constitution of steel is determined by the addition or absorption into the bath of all such constituents from whatever source, it follows that constitution is of necessity the final result of steelmaking practice. It is the agency through which steelmaking practice operates to control the properties of the steel. The term steelmaking practice is here used in the broad sense, meaning the control of all the materials entering the steel and of the conditions under which the process is carried out. Steelmaking practice, thus defined, establishes the chemical system within which the reactions between components must proceed in obedience to the laws of chemistry. Thus the chemical constitution of the steel is established and, through constitution, the properties of the metal are established. In the preceding chapters it has been shown how the constitu-

Jan 1, 1951

By B. G. Klugh

The present paper represents a preliminary investigation of the ultimate structure of iron-bearing materials which have been subjected to heat treatment for the purpose of agglomerating the fines, or for chemical changes, or for both. Primarily, the object of this inquiry was to determine the relation of the microstructure of each of these materials to its specific susceptibility to the action in the blast-furnace. It is hoped that this small contribution will serve as a nucleus to a line of research that will throw some light upon the debated questions involved in blast-roasting. Thus far the investigation has been conducted along lines of analogy of known principles, rather than through the application of any well-defined system of microscopic petrography. This is obviously due to the fact that we are dealing with ma-terials which are the artificial products of a new art, rather than with the natural materials from which the essence of the pure science has been evolved. In the limited time allowed for this research, it has been conducted upon those materials the chemical content of which allows of their use commercially in the blast-furnace. The following microphotographs are arranged in the order of the degree of complete fusion to which the mass in question has been subjected, in effectively binding the particles together. A very notable fact here clearly demonstrated is that the degree of fusion to which the material has been subjected is inversely proportional to the reducibility of the product. The characteristic of the material under consideration to which reducibility is almost universally attributed call be progressively traced in the following arrangement, through the identity of the obvious microscopic constituent. Furthermore, the degree of fusion to which a bod? has been subjected is recorded in the presence of resultant products of fusion in that body. Such readjustment is generally apparent

Jan 1, 1914

By S. S. Nosseir

INTRODUCTION General Quebec Cartier Mining Co. (QCM) , Canadian subsidiary of U . S. Steel Corporation, operates two iron ore concentrators at the North Shore of Quebec, Canada. In its own operation at Mount-Wright, over 45 million tons per year of crude ore are ground, fully autogenous in six 32' x 11-1/2 Dominion Engineering mills. At Fire Lake/Lac Jeannine operation, property of Sidbec Normines Incorporated (SNI), over 11 million tons per year of crude ore are now ground, fully autogenous, in twelve 18' x 5' Hardinge mills. The Lac Jeannine concentrator was originally constructed by Q.C.M. in 1960 and. was since operated, in beneficiating the Lac Jeannine ore deposit until fully depleted in 1977, at an annual capacity of 18 million tons of crude per year. In 1976, the new company, Sidbec Normines, was incorporated by Sidbec Corporation, British Steel Corporation and Quebec Cartier Mining Co., in proportional holding of approximately 51 to 41 to 8 percent respectively. Since the acquisition of the Fire Lake ore deposit and Jeannine concentrator by the new company, QCM has continued managing the mine and concentrator operaions for S idbec Normines Inc . Flow-Sheet Design Jeannine concentrator comprises twelve identical mill lines grinding the ROM from 8" top size to 14 mesh nominal size range. Driven by 600 H.P. motor at 13.4 RPM corresponding to 73% critical speed, each mill is operated in a closed circuit with two 5' x 12' vibrating screens dressed with 2.5 x 25 mm slot opening cloth. The ground product or screen undersize at an average grade of 33.4% Fe is beneficiated by gravity separation to produce 66.5% Fe concentrate grade at 42.7% weight recovery. At the rougher stage, each mill line con-tains 128 Humphrey 13- 1/2" pitch spirals which produce a final tailing, middling and concentrate products. The rougher concentrate - so produced - is classified by 64 Humphrey pocket sizers into an underflow, which is a final concentrate product and an overflow which is further upgraded by 64 cleaner spirals. The cleaner concentrate together with the pocket sizer 's underflow are dewatered on a 13'[6] horizontal filter. The rougher middling together with the cleaner tailing are recycled in a closed circuit with the spirals. The rougher tailing after dewatering by hydrocyclones is disposed of by a

Jan 1, 1982

By F. R. Hensel

Up to the present time few attempts have been made to produce hard nonmagnetic materials by heat treatment of austenitic steels. The usual result has been to cause them to pass into the martensitic stage, thus destroying to a great extent the typical austenitic properties, since this involves a transition of a portion of the iron from a face-centered to a body-centered type of atomic arrangement. High-strength nonmagnetic materials such as might be provided by properly hardening austenite are required in the electrical industry for different machine parts. In Europe nonmagnetic retainer rings for restraining the end-turns of the rotor windings in turbo-alternators have been developed as a special application of high-strength austenite. In testing1 a 28,000-kva. three-phase Siemens turbogenerator running at 3000 r.p.m. at full load current, the losses in the short-circuit test were 450 kw. for the magnetic ring and 286 kw. for the nonmagnetic, and the difference should be attributable to the magnetic ring. The differences in temperatures during the same test are given in Table 1 and these show the advantage of a nonmagnetic over a magnetic retainer ring. Hardening in this case was obtained by cold working, such as hammering, rolling or some means for stretching the steel while at a temperature near 500" C. One means for stretching2 is to rotate the forged or rolled ring in a centrifugal machine so as to develop within it stress higher than

Jan 1, 1931

By B. C. Allen

Grain-boundary gvoocing was studied irz chronziu?n. molybdenum, tungsten, and the solid-solution alloys, Cr-35Re. Mo-33Re, and W-25Re at 0.6 to 0.9 of the absolute liquidus temperature under an inevt atmosphere , foveign nzetal zlapor, and liquid metal. The controlling mechanism of matter transport was deduced frolr groove size and shape. kinetics of growth, and cotnparisoz with theoretical relatiotzships derived by Mullins. Grooves in chowzizon formed prittzarily by volume diffusion tkrongk kelium or argon at 1 atm pressure and by e1)apovation-condensatiotz in a static vacuum. Groozles in the other nzetals and alloys forrned priniarily by sirface diffusion, the coefficients of which were calculated. Carbon was found to decrease the acti7:ation energy for surface diffusion on molybdenun. Sitrface diffusizities weve sinzilav for iWo-0.0ZC and Mo-33Re. The presence of about 1 -?nm pressure of silver or tin vapor did not affect the neckanis)n of grooz;e formation. In liquid titz or silz:er, pain bolindary gvooves formed by zolume diffusion in the liquid. BASED on theories of ullins," the mechanisms of grain-boundary grooving have been determined for low-melting metals such as copper in an inert atmospheres or in liquid lead.4 The purpose of this investigation was to study grain-boundary grooving in the refractory Group VI-A metals, chromium, molybdenum, and tungsten, and the bcc solid-solution alloys, r-35e, 0-33e,= and -25e,' at 0.6 to 0.9 of included to see whether Mullins' theories were applicable to them as well. EXPERIMENTAL WORK The materials chromium, molybdenum, tungsten, Cr-35Re, Mo-33Re, and W-25Re were in the form of 0.050-cm-thick sheet assaying 99.98 pct or better. The nominal carbon level was generally 30 ppm. The oxygen + nitrogen + hydrogen content was -50 ppm. Mo-33Re and W-25Re were prepared by powder-metallurgy methods and supplied by Chase Brass and Copper Co. The remaining materials were arc-cast. Chromium and Cr-35Re were prepared at Battelle by arc melting, extruding, swaging, and rolling. Mo-0.003C was supplied by Climax Molybdenum Co., and Mo-0.02C and tungsten by Universal Cyclops Corp. As a source of liquid metals, tin and silver granules assaying 99.98 pct were used. Spectrographic analyses indicated the presence of -100 ppm each of iron and silicon. Vacuum melting reduced the combined gas content to c5 ppm (2.60,, 0.9N2, 0.4H2 in tin and l.602, 0.7N2, and c0.04H2 in silver). Specimens were prepared for grain-boundary grooving. Coupons 0.5 by 1.5 cm with a small hole in one end, or substrates 1.5 by 1.5 cm, were cut from sheet. The specimens were annealed in containers of the same material to provide a vapor-solid equilibrium as well as to protect them from gaseous impurities. Outgassing was done at 2 x 10"5 mm for 15 to 30 min at 1150°C for chromium and Cr-35Re, 1750°C for molybdenum and Mo-33Re, and 2600°C for tungsten and W-25Re. Then recrystallization to a stable grain size of about 0.5 mm was accomplished by annealing at least 1 hr at 1600°C for chromium, 1800°C for Cr-35Re, 2350°C for molybdenum, and 2300°C for Mo-33Re in a rhenium-element resistance furnace under 1 atm of static argon or helium. The atmosphere was gettered by tantalum radiation shielding. Tungsten and

Jan 1, 1967

By Robert J. Hite, Samuel S. Adams

Potash, the generic term for a variety of potassium-bearing minerals, ores, and refined products (Table 1), owes its importance as an industrial mineral to the potassium requirement of growing plants. The term potash originally referred to potassium carbonate produced by the leaching of wood ashes. This process, for which the first US patent was issued in 1790, was the basis for the largest United States chemical industry in the early nineteenth century. The agricultural use of potash soon eclipsed the chemical applications following the German discovery in 1840 that potassium is essential to plant growth. The initial discoveries of large deposits of soluble potassium minerals, essential for agriculture applications, were made in 1857 in Germany and in 1914 in the United States. More than 90% of the 27.5 Mt K20 produced in the world in 1980 (Searls, 1981) was derived from marine evaporite deposits and approximately 90% was used in fertilizers. The potassium content of an ore, mineral, or product is customarily expressed as % K20, a unit of measure which is neither a natural nor synthetic compound of potassium (1.0% K is equivalent to 1.2046% K2O). Geology Potassium, the seventh most abundant element in the earth's crust, is present in silicate minerals in igneous, sedimentary and metamorphic rocks. Potassium is also a major constituent of many surface and subsurface brines (Table 2). Economic potash deposits are essentially restricted, however, to widespread, thick accumulations of marine chloride evaporite deposits. These deposits yield high grade, large tonnage ore bodies, many of which are amenable to low cost mining and beneficiation. The products from these deposits are, moreover, ideal for use in fertilizer because of the high relative solubility of the potassium chloride and sulfate evaporite minerals. World potash production and reserves for such deposits so vastly overshadow other sources of potassium that the following discussion will be limited largely to potash deposits in marine evaporites with brief reference to certain potash-rich brines. Approximately 85% of current domestic production is from bedded salt deposits and much of the balance is from brines. Marine evaporite deposits are accumulations of salt minerals deposited in structural sedimentary basins through the evaporation of seawater or mixtures of seawater and other brines. The salt minerals are precipitated in assemblages and sequences of assemblages as determined by the compositions of the brines and the solubility relations in the salt systems (D'Ans, 1933). The evaporation of seawater normally yields carbonate minerals as the first precipitates (Table 3). Further evaporation and concentration of the brine leads to the precipitation, in succession, of sulfate, chloride, and supersaline mineral assemblages including the salts of potassium and magnesium. The common minerals, ores, and products of potassium deposits are listed in Table 1. Many potash deposits contain accessory evaporite minerals together with a variety of detrital and authigenic silicates (Braitsch, 1971). The structural basins within which marine evaporites occur are of two main types: (a) cratonic basins formed by broad epirogenic movements (for example, the Michigan Basin of the midwestern United States and the Permian Zechstein Basin of eastern Europe), and (b) grabens, commonly related to continental

Jan 1, 1983

By H. W. Ahrenholz

Seven weeks of 1971 were devoted to a nationwide coal walkout resulting in lost production of some 70 million tons and leaving 1971 coal production at about 550 million tons. Compounding the problem, consumption of coal in 1971 by electric utilities rose by about 5% to 336 million tons. In the mean- time, numerous contracts were awarded for coal R&D including $24.8 million given by the Office of Coal Research to Bituminous Coal Research for the construction of a coal-to-gas pilot plant using the BIGAS process. Exports declined mainly due to Japan's decrease in steel production and to that country's increase in coal imports from Canada and Australia. The advances in equipment design and mining procedures made 1971 a noteworthy year. Introduction of the variable pitch I dipper, the trend toward wheeled vehicles, the greater use of scrapers in reclamation and battery-operated vehicles and oscil-mining, and the increased activity in the areas of ventilation and dust control were given widespread approval. There were also strides made in computerization, longwall mining, roof bolting, rock dusting, mine haulage and methane detection.

Jan 2, 1972

By Robert Glass Cleland

FROM the time of its organization down to 1917, a period of more than eighty years, Phelps, Dodge & Co. was seldom involved in what could be called a major labor difficulty. Behind this remarkable record lay both a philosophy and its practical application. The philosophy was an attitude toward society called the Golden Rule. That philosophy had been a living principle in the lives of the founders of the company, Anson Phelps, Daniel James, and William E. Dodge. Their successors, William E. Dodge, Jr., and Daniel Willis James, accepted the same philosophy. Dr. James Douglas governed his life by it. All of these men and their families had given tangible expression to that conviction in benefactions of great magnitude and variety-churches, hospitals, educational institutions, libraries, missionary undertakings, and other organizations for human betterment, such as the Young Men's and Young Women's Christian Associations, and the development of model communities about their mills and factories. According to the best standards of their generation, they had sought to improve the condition of labor,

Jan 1, 1952

By Strathmore R. B. Cooke, Iwao Iwasaki, C. S. Chang

PYRRHOTITE has long been considered a gangue mineral to be eliminated as tailing in the treatment of various sulphide ores. However, in recent years the world-wide lack of sulphur resources has called attention to this mineral as a potential source of both sulphur and iron. Its importance as an economic mineral, however, has not been particularly emphasized. For this reason very little is known about its response to flotation, except that it can be depressed easily in alkaline circuit, by long aeration,1,2 addition of oxidizing agents3 or by starch.4 The object of this work was to study the floatability of pyrrhotite. This includes the effect of oxidation by aeration, of copper activation, and of change in pH.

Jan 2, 1954

June was the month in which AIME was founded in the year of 1871. For some reason, February was selected as the month for the legal Annual Meeting. One can't help thinking wistfully of Annual Meetings in June but of course this is not the reality. Because the Centennial Ceremonies are taking place in February, that month has been chosen as the one in which MINING ENGINEERING, the monthly magazine of the Society of Mining Engineers, a constituent society of AIME, is publishing its Commemorative is- sue to celebrate the event. SME and ME take a proprietary air about AIME. This is mostly because AIME started as the American Institute of Mining Engineers. Metallurgy was added to the name in 1919 and Petroleum in 1956. The official abbreviation of "AIME" has been retained, however.

Jan 1, 1971

By H. M. St. John, T. Rynalski, G. K. Eggleston

Maintaining a satisfactory structure in brass and bronze castings has always been a foundry problem of great practical importance. While metallurgists and scientific investigators have not entirely ignored this matter, it has received less of their attention than has been given to iron, steel and the wrought copper and aluminum alloys. Investigation in this field has probably been discouraged to some extent by the complicated nature of the alloys involved. Hundreds of alloys are in more or less common use, most of them containing copper, zinc, lead and tin in widely varying proportions. They also contain appreciable percentages of iron and antimony as impurities, and often phosphorus, which has been added as a deoxidizer and fluidifier. Small amounts of sulfur are usually present. It is not uncommon to find nickel, sometimes in rather substantial quantities. Traces of other metals are frequently present. So complicated and variable a mixture obviously offers difficulties in any investigation of the various factors that influence the structure and other properties of the casting. Incipient Shrinkage Bolton and Weigandl have called attention to a type of structure characterized by intercrystalline fissures and large dendritic crystals which are frequently tarnished to an orange or reddish brown color. This intercrystalline porosity they term "incipient shrinkage" and attribute to the presence of carbon monoxide in the atmosphere under which the metal was melted. The defective structure to which Bolton and Weigand refer has become a brass-foundry problem of major importance, because it occurs with distressing frequency in leaded brasses and bronzes when these are melted in a neutral or reducing atmosphere. Since the electric furnaces, now coming into general use in brass foundries, normally operate with such an atmosphere and, in fact, depend upon it in part

Jan 1, 1930