Search Documents

By Albert S. Trube

The purpose of this paper is to clarify the definition of compressibility and to present a uniform basis upon which instantaneous compressibilities of liquids and gases can be compared. The equations gaverning the instantaneous compressibilities of imperfect gases are derived and the concept of pseudo-reduced compressibility is introduced. Part of the data presented by Brown, Katz et a1 on compressibility factors for natural gases has been rearranged. A graph of pseudo-reduced compressibility vs pseudo-reduced pressure for various pseudo-reduced temperatures is presented. The need for additional work in relating the compressibilities of liquids and gases is discussed. This information should be of value to reservoir engineers in making non-steady state performance calculations in gas reservoirs. It should be of further use irz pointing the direction for additional research in the nature of liquid and gas compressibilities. INTRODUCTION With the increasing use of steady and non-steady state well and reservoir data, there is a corresponding increase in the importance of the various factors entering into such calculations. Increasing emphasis is being placed on the necessity for obtaining reasonably accurate estimates of the physical properties of the reservoir fluids well in advance of the more accurate laboratory data. One such factor is the isothermal coefficient of expansion of the media which are transmitting and attenuating the non-steady state pressure waves. The average isothermal coefficient of expansion, or "compressibility" is a complex function controlled by the physical properties of the formation and the fluids contained therein. The isothermal expansion coefficients for reservoir gases are usually quite variable, in many cases being highly-pressure sensitive. The coefficients for reservoir liquids tend to be pressure sensitive, but not nearly so much as reservoir gases. The coefficients for solids, usually expressed in terms of a "modulus of elasticity" are relatively insensitive to pressure variations within their elastic limits. For this reason, and also because many previous applications have been limited to rel- atively small pressure ranges, there has been a tendency to ignore the variable nature of isothermal expansion coefficients and treat them as constants. Also, the term "compressibility" by which these coefficients are generally designated is commonly confused with a similar term, z, used to define the deviation of an imperfect natural gas from the perfect gas laws. A clear distinction should be made at the outset between the term "compressibility", which is an isothermal coefficient of expansion of a substance, and the term "compressibility factor", z, which refers to the deviation of a gas from the perfect gas laws. Although the scope of this paper is limited to the compressibility of single phase natural gases, it is definitely related to the problem of accurately estimating the compressibilities of single phase hydrocarbon reservoir liquids, which will form the basis of a future presentation. BASIC PRINCIPLES The coefficient of isothermal compressibility of a substance, c, is usually determined from pressure-volume or pressure-length -measurements depending upon whether the substance is single phase gas, liquid, or solid. A convenient method for making such estimates for a finite change in pressure and volume at constant temperature is to use the well known equation V1-V2/V1 (p2 - p1) .....(1) Eq. 1 is negative because the volume of a confined substance decreases as the pressure is increased. In this case V1 > V2 and p2 > p1. This equation is useful in approximating the compressibilities of single phase gases and liquids undergoing small pressure changes. It is evident, however, that this equation is almost identical with the determination of Young's modulus of elasticity for solids. If the assumption is made that change in length is directly proportional to change in volume, as would very nearly be the case for a steel rod in tension within its elastic limit, then E5=-L1 (p2 - p1)/L1 - L2 .......(2) in which E. is the isothermal expansion coefficient, or Young's modulus of elasticity, for a solid. And further, for this special case L1 (p2 - p1)/L1 - L2 .......(3)

Jan 1, 1958

By A. Bauer, P. Calder, N. H. Carr, G. R. Harris

Since both rotary and jet piercing drills are used by the Iron Ore Co. at Smallwood, it is often desirable in planning to know in which regions of the orebody or new orebodies a particular drill will be the most economic. This makes it necessary to establish a correlation between drillability and pierceability and some physical rock properties. For rotary drills a good correlation was found with penetration rate and grinding factor index. The jet piercers were found to have a reciprocal relationship in the sense that the best rotary ground was the worst jet ground and vice versa. It is also indicated how an economic comparison could be made using these penetration rate versus grinding factor index curves, the hole size distribution curves for single pass and chambered holes and the mine distribution curve for grinding factor index. A discussion is presented on the fuel oxygen ratios to be used in jet piercing and on the site gas sampling and analysis which has been used to set up the drills. The fuel has been cut back so that stoichio-metric conditions exist, carbon monoxide is drastically reduced and pop-up or exploding holes eliminated. No decrease in penetration rate has been observed contrary to the published results of previous workers. The blasting procedure and results at Smallwood are discussed and the operation of Iron Ore Co.'s slurry pump-mix truck is also described briefly. Smallwood mine is part of the Iron Ore Co.'s Carol Lake operation and is situated in Labrador, 240 miles north of Sept-Iles, Quebec. Last year 15 million tons of crude ore were crushed to yield 6.3 million tons of concentrate and pellets. This year the figures will be 17 million tons of crude and 7% million tons of concentrate and pellets which is the full plant capacity. Carol Lake ores consist primarily of specularite and magnetite mixed with quartz. For convenience the ore has been split-into the following classifications depending on the percentage of magnetics in the sample, shown in brackets: specularite (0 to 10%), specularite-magnetite (10 to 20%), magnetite- specularite (20 to 30%), magnetite (>30%). The order of classification also represents the order of increasing grinding difficulty - the specularite generally being the easiest and the magnetite the hardest. The orebody also contains a small percentage of waste materials consisting of limonite carbonate, quartz carbonate and quartz magnetite. The first two materials are among the softest in the mine, generally softer than the specularite, and the quartz magnetite is amongst the hardest. The bulk of the material in the mine is of the specularite-magnetite and magnetite-specularite classifications. As a result of test drilling at Smallwood in 1960 with rotary, jet and percussion drills, the Iron Ore Co. purchased four JPM-4 jet piercers for the bulk of production drilling and set up an oxygen plant to supply 20 tons of oxygen per day. This oxygen is sufficient for two machines operating full time and one part time. In addition, there are two 50-R, one 60-R and one 40-R machines in use. The benches are 45 ft high and 50 ft holes are generally drilled. JET DRILLING At the onset of jet drilling in the late fall of 1962, two major problems were encountered: 1) freezing due to winter operations; experience and the use of heat at more places, such as the rotary head, has eliminated this,'" and 2) exploding or "popping" drilled holes; this happened frequently (several holes "popping" each day) and was the cause of two lost time accidents. In one instance a hole was being measured with a tape which fell down the hole causing it to "pop." Safety glasses though pulverized saved the wearer's eyesight. Various methods were then employed to detonate the holes before measuring or loading (dropping lighted rags of fusees down, or sparking across a spark gap). These methods were time consuming and far from completely successful. Consideration was given to the fuel oxygen ratio on the machines and what this would produce in the way of product gases. A fuel oxygen weight ratio of 0.35 which was quite oxygen negative was being used. Theoretically appreciable carbon monoxide would be produced at this fuel oxygen ratio. On the close down procedure of the jet which calls for low oxygen after flame out, oxygen would be left in the hole along with this carbon monoxide. This is an explosive mixture. The fuel oxygen ratio was cut back to stoichiometric

Jan 1, 1967

By John W. King, S. Ralph Austin

Spurred by recent forecasts of greatly increased demands for uranium by 1980 and beyond, interest is once again focusing on America's western uranium deposits. One of the principal producers in this area is the Gas Hills district in Wyoming, the site of approximately 12% of the known uranium in the U.S., including past production and current reserves. Located on the south flank of the Wind River Basin, the Gas Hills deposits have been recently studied by the Atomic Energy commission for clues to and guides for discovering similar-occurring ores. The ore deposits are confined to a permeable sandstone unit, up to 350 ft thick, at or near the base of the upper Wind River formation of early Eocene age. The uranium occurs in three principal north- south "ore trends," each of which is about six miles long, one mile wide, and separated from each other by approximately three miles (Fig. 1).

Jan 5, 1966

By AIME AIME

THE outstanding event of the past month has been the conference in Washington of the representatives of about seventy-five of the leading national, regional and local engineering and allied technical organizations." Editorial-July Journal-The American Society of Mechanical Engineers. ?Prominent engineers from all parts of the country, representing more than 75 engineering societies, with an aggregate membership of more than 125,000, participated in the organization.? Editorial-July Journal-American Institute of Mining and Metallurgical Engineers. ?Civil, mechanical, electrical, mining, heating, sanitary, chemical, agricultural, marine, refrigerating, radio, fire protection, automotive, industrial and military engineers, as well as some architects and geologists assembled at Washington, D. C. to consider the advisability of organizing a national federation capable of bringing the united efforts of the entire membership to a focus on any problem of mutual interest." American Architect, June 23, 1920. ?"the object sought places it above any engineering gathering ever held." Editorial-American Machinist, June 17, 1920. "The youngest. profession has voluntarily accepted its responsibility in human affairs and is now reaching forward to a career of essential service." "This is .unmistakably the meaning of the Organizing Conference " Editorial-Industrial Management, July; 1920.

Jan 1, 1920

By B. J. Kochanowsky

The idea of a portable crusher is not new. Many such crushers are available but they are small and designed for construction work. For many years the author has suggested, both in this country and in Europe, the building of larger portable crushers intended expressly for use in quarries or open pits. Although not applicable under all conditions, there are mining operations where a mobile crusher arrangement could be more profitable than the facilities now used. The primary use of a portable crusher, i.e., a crusher mounted on crawlers or tires, in the rock and mining industries is to reduce costs by permitting the substitution of conveyor belt haulage for truck or track haulage. The usual sequence of operations in surface mining is drilling, blasting, loading, haulage, and crushing. Haulage is normally accomplished by truck or track-mounted cars, the latter method being used for the longer distances. However, by using a portable crusher in the pit, the sequence of operations would be changed so that the crushing stage would occur before haulage (Fig. 1). Such a sequence would permit the use of conveyors to replace the more expensive truck or track haulage methods. Since most quarry and open pit operations normally require a crushing stage, the only additional costs incurred will be due to the investment required to purchase or construct a mobile arrangement for a crusher. But this factor has to be weighed against the advantages to be gained by conveyor haulage. As shown in Fig. 2, transportation of material by belt conveyor over short distances is less expensive than by truck. The inclination of the belt has no effect on belt speed; consequently, the hourly tonnage moved remains the same. Conversely, the output rate of trucks as expressed in tons or ton-miles per shift decreases proportionally to the haulage speed, which is considerably slowed by the steepness of the road (Fig. 3, left). Although maximum possible grades and maximum economic grades of haulage are greater for a belt than for a truck (over the same total lift), the longer haulage distances favor the use of trucks. Although power consumption for hauling on a grade increases for both conveyances, the rate of power consumption increases faster for trucks than for conveyor belts (Fig. 3, right). Since the output rate and related fixed costs are affected by the travel speed, total haulage costs with trucks would increase with the grade more rapidly than the similar costs of conveyor belts (Fig. 4). Travel distance, road grade, speed, size and number of pieces of equipment, efficiency of operation, and many other factors affect such haulage costs. In general terms it can be said that the shorter the distance, the steeper the grade, and the greater the output, the more advantageous the belt becomes in comparison to truck or track haulage. In addition to potential cost savings in haulage procedures, a portable crusher would allow better utilization and performance of shovels. Loading operations would not be interrupted as often by the necessity of waiting for cars or trucks. Unfortunately, the application of belts in open pits for haulage from bench sites is generally not practical under existing conditions because a belt fed directly by a mechanical shovel can be torn, damaged, or worn out quickly by the large rock fragments falling on it during loading. However, by using a mobile crusher this situation can be avoided. As shown in Fig. 1 (b), the shovel feeds rock into the crusher located behind it. The crushed material is initially transported by an extensible and/or movable belt, thence by a longer stationary conveyor to the plant where the material is subjected to further treatment by secondary crushing, screening, etc. The first-mentioned conveyor, needed to bridge the distance between the shovel and the stationary conveyor, is necessarily variable in length owing to the continuous movement of the shovel and the desire to keep the stationary belt at a safe distance from the bench during blasting operations. The remarkable part of mobile crusher operations is the extra-ordinarily high output per man-shift, the low maintenance and power requirements for haulage, and the increased output of the loading shovel. A cement quarry which has been using a portable crusher and conveyor since 1956 requires only three men to operate the shovel and crusher and to transport the crushed rock by belt from the quarry face to the screening plant. If truck haulage

Jan 1, 1961

By Paul Klopstock

(Butte Meeting, August, 1913.) THE Kennedy mining district is situated about 55 miles in a southerly direction from Winnemucca, and about the same distance south-east from Battle Mountain : two towns situated oil t the main line of the Southern Pacific railroad. History. Prospectors were first attracted to the district by the reported discovery of gold by Chinamen in Cinnabar creek in the early 90's. The prospectors came from the rich placer workings in and about American canyon ; but the new diggings were not found sufficiently rich to justify their being, worked as placer properties, and the prospectors started work in a number of places, looking for the veins which had fed the canyon. In 1893, Charles E. Kennedy, a prospector who had been attracted by the reported discoveries in the vicinity, left Hawthorne and came to the present site of the town of Kennedy. Within a short time he discovered the vein known as the Imperial, and proceeded, with the aid of some friends, to develop it. The vein was readily traced for a distance of about a mile, and about $10,000 worth of high-grade ore was shipped to the Utah smelters. At about the same time the Lawler Brothers, who had been prospecting in the district for some time, located the ?Gold Note group," which showed some extremely rich ore. Within a very short time they extracted from 'the Gold Note vein 150 tons of ore, which was shipped to the Utah smelters, and netted about $105 per ton above all expenses. Their good fortune attracted attention to the camp, and within .a short time a town was laid out, with a population of about 500 people. It was named in honor of Kennedy, who had made the first discovery of pay ore in the district.

Jan 6, 1913

By Arcy A., J. G. Davis, D&apos Shock

Results of a pilot operation in the Carlsbad Basin are discussed. After hydrafracing between wells, a block of potash was removed by solution techniques. The distance between frac wells was about 200 ft, the thickness of potash mineralization, 5 ft. By proper manipulation, a feed of concentrate brine was obtained. The ex-periment showed that the thin-bedded potash could be removed by the solution techniques. The details of well construction, method of operation, and removal rates are discussed. Continental Oil Co.'s laboratory research on the fundamentals of potash solution mining has been expanded by means of a series of field tests, and subjects such as well completion and hydraulic fracturing were added to the investigation. Both single-well and multi-well systems were studied in the field work. Discussion Background: The current paper discusses one field test in which potash was solution mined by a two-well system from a thin sylvinite zone. The potential economic value of solution mining evolves from (1) the use of drilled holes and solution techniques instead of excavated shafts and caverns and (2) the ability to mine both land and marine deposits through any type of overburden geology and below conventional mining depths. Recent interest has been focused on potash' and other soluble minerals, such as trona. Solution extraction minerals, such as copper and uranium, are also worthy of important consideration. In addition, many of the techniques are directly applicable to the construction of horizontal underground storage carverns in salt. There are two general approaches to potash solution mining. The first is to mine on a single-well basis, in which the same well bore is used for both injection and production. This method is slow, and the areal extent may be quite limited in other than very thick ore zones. The second, and the preferred approach, is to mine on a multi-well basis in which the solvent is circulated between wells. This technique, if applied in a manner which allows the ore zone to be mined from the bottom upward, results in nearly all the solution taking place from the cavern roof. Salt removal rates, therefore, are very much higher than from a single-well system.l Wells can be interconnected into a multi-well pattern by several means. One is to join single-well caverns in the lower part of an ore zone. Another is to use the hydraulic fracturing techniques developed in the oil fields.' We preferred the fracture approach because of its potential for creating the greatest area of salt exposure. Test Site Description: The field tests were conducted in New Mexico's Carlsbad Basin, where the potash deposits are flat and uniform over reasonable distances. Here, 12 potash zones are present in the massive Salado Salt section. The specific target was the Third Ore Zone which is about 4 ft thick at our location and about 1150 ft deep. The test pattern was designed in the shape of an equilateral triangle with a fourth well located in the center, 200 ft from each of the vertex wells. This configuration allowed the ore zone to be hydraulically fractured from the center well with good assurance that the fracture would intersect the bore of at least one outside well. Several multi-well test patterns would be available if the fracture connected all wells. Well Completion: Surface casing was set in the top of the Salado Salt at 600 ft to shut off water flows from the surface sands, and the salt section was drilled and diamond-cored to a point below the Third Ore Zone. A drilling fluid made of diesel oil with a small amount of emulsified water was used to drill and core the salt. This fluid was highly successful in preventing enlargement of the drilled hole and in promoting good core recovery. The three outside wells were completed by setting 51/2-in. casing at the base of a streak of anhydrite about 20 ft above the ore zone. Pipe was set high so that the intersection point of the fracture could be detected even if the fracture migrated above the ore zone as it progressed outward from the center well. The center well itself was completed by cementing 51/2-in. casing through the Third Ore Zone. Cement bond logs run on the center well have shown excellent bonding. Fracturing Practice: A mechanical tool was used to cut a notch through the casing and into the salt at a point about 1 ft below the ore zone in the center well. The purpose of this notch was to fix the point of fracture entry into the salt. The fracturing was done with water at injection rtaes as high as 30 bbl per min. The salt parted at 1450 psi; and it required only 5 min for the fracture to reach the well which was 200 ft to the south. It took about 5 min more to reach the other two wells. Caliper surveys were run to locate the point of fracture entry in the three outside wells. The fracture appears to have drifted downward slightly, entering the outside wells at the top of a streak of carnallite 8 or 9 ft below the ore zone. A cross section of the wells selected for the multi-well test is shown in Fig. 1. The figure includes KC1 values based on core analysis and the trace of the fracture plane between the wells.

Jan 1, 1971

By F. C. Blake

THE test of the English cupellation furnace should be so supported that the cupeller can change readily the elevation of the test, and at the same time watch the litharge channel. It is also important to raise or lower either side, independently of the other, in me of uneven wear of the side walls or of the breast. If the refined silver is poured from the test, it is much better to control the lowering of the test from the front than to raise the back by screws or a lever. In order to enable the cupeller to manipulate the test with one hand, when the litharge is running, and to pour the refined silver from the test without aid, I have altered the common support to the test, as shown in the accompanying drawing. The common method of supporting the test is by four screws, working in cross-bar nuts beneath the test. The points of the screws set, into the test plate upon which the test rests. These screws are usually worked by pounding or pulling upon the heads, which may be either small pulleys or straight bars, as shown on the back screws in the drawing. The screws are also worked by turning a crank, which is

Jan 1, 1882

By F. C. Blake

THE test of the English Cupellation furnace should be so supported that the cupeller can change readily the elevation of the test, and at the same time watch the litharge channel. It is also important to raise or lower either side, independently of the other, in case of uneven wear of the side walls or of the breast. If the refined silver is poured from the test, it is much better to control the lowering of the test from the front than to raise the back by screws or a lever. In order to. enable the cupeller to manipulate the test with one hand, when the litharge is running, and to pour the refined silver from the test without aid, I have altered the common support to the .test, as shown in the accompanying drawing. The common method of supporting the test is by four screws, working in cross-bar nuts beneath the test. The points of the screws set into the test plate upon which the test rests. These screws are usually worked by pounding or pulling upon the heads, which may be either small pulleys or straight bars, as shown on the back screws in the drawing. The screws are also worked by turning a crank, which is

Jan 1, 1882

By William S. Dershowitz

INTRODUCTION Numerical methods commonly used in rock mechanics, such as finite element, displacement discontinuity, and boundary integral equation methods, offer solutions to problems which can be described by differential equations subject to boundary conditions. These numerical methods use approximations leading to solutions in terms of matrix algebra and numerical integration. Many rock mechanics problems which are beyond the scope of such approximations can be treated effectively by application of techniques developed in the field of artificial intelligence (AI). Among the possible applications are: site characterization (Duda, 1975), geological interpretation (Smith and Baker, 1983), solution of problems involving rock joint networks, and underground construction. Each of these applications utilize particular features of Al. Here we shall present results of AI applications which utilize primarily search and to lesser extent learning or pattern recognition. Specific examples presented are in the field of rock fracture network problems and underground construction. ARTIFICIAL INTELLIGENCE Artificial intelligence techniques attempt to achieve human-like reasoning and learning capabilities. This reasoning capability is valuable in applications where repetition, complexity, or tediousness makes human-like intervention impractical. In rock mechanics this occurs, for example, in stochastic rock mass modeling applications where some complex decision-making is required for each of a large number of iterations.

Jan 1, 1984

By H. Cecil Spicer

The results described in this article are based On field work conducted during the periods April-May, I939, and May-July, 1940. The United States Potash Co. is mining potash on Government land under a permit from the Department Of the Interior and the geophysical investigation was completed under a cooperative arrangemerit made between that company and the Conservation Branch Of the Geological Survey. The writer, a member Of the SeCtion of Chemistry and Physics of the Geologic Branch, was assigned to this investigation. Four definite objectives were in mind for the geophysical work in the studies over the salt deposits. The first was to determine the measure Of success that could be attained in this type of work with the resistivity methods that were to be employed. These methods had been introduced into the work of the Conservation Branch by Benjamin E. Jones for the investigation of dam sites, and have been used under his direction by the author for such work. If the method proved to be be an effort was to be made to contour the top of the salt beds and also the other formation boundaries known to be present in this area. Salt-water aquifers were to be studied in an effort to determine their boundaries, and an attempt was to be made to delineate the potash-bearing beds. Earlier Studies Others have made, and reported, restivity studies over saliferous deposits in different areas. Friedell and Messrs. Schlumberger2 reported geophysical work performed in the discovery of the salt domes of Alsace; Carrette and Kelly? described the geology of the same area. Leonardon and Kelly' published a resistivity curve obtained over the Hettenschlag dome, and a further discussion of this same area was given by the Messrs. Schlumberger6 in a communication. Messrs. Alty6 described studies on salt deposits in which the single-probe method was used. sinerez7 mentions that electrical methods were tried over salt deposits in Spain. Geoffrey and Charrin8 show a resistivity curve obtained over marl, gypsiferous marl and salt which is similar to that obtained over the New Mexico salt deposits. Kelly9 reported resistivity work performed with the ground Comparaor of Zuschlag over the salt deposits near Syracuse, N. Y., where the Salina formation is at a depth of 700 to 800 ft. Some structural studies on the potash basin of Alsace are described by Poldini.10 Another single-probe resistivity study, made over salt deposits in New Mexico, is briefly described by Heiland,11 through the courtesy of Harry Aurand, of the Midwest Refining co, Geological Features OF Area Covered The area discussed in this paper is in Eddy County, southeastern New Mexico, a

Jan 1, 1946

By H. Cecil Spicer

The results described in this article are based On field work conducted during the periods April-May, I939, and May-July, 1940. The United States Potash Co. is mining potash on Government land under a permit from the Department Of the Interior and the geophysical investigation was completed under a cooperative arrangemerit made between that company and the Conservation Branch Of the Geological Survey. The writer, a member Of the SeCtion of Chemistry and Physics of the Geologic Branch, was assigned to this investigation. Four definite objectives were in mind for the geophysical work in the studies over the salt deposits. The first was to determine the measure Of success that could be attained in this type of work with the resistivity methods that were to be employed. These methods had been introduced into the work of the Conservation Branch by Benjamin E. Jones for the investigation of dam sites, and have been used under his direction by the author for such work. If the method proved to be be an effort was to be made to contour the top of the salt beds and also the other formation boundaries known to be present in this area. Salt-water aquifers were to be studied in an effort to determine their boundaries, and an attempt was to be made to delineate the potash-bearing beds. Earlier Studies Others have made, and reported, restivity studies over saliferous deposits in different areas. Friedell and Messrs. Schlumberger2 reported geophysical work performed in the discovery of the salt domes of Alsace; Carrette and Kelly? described the geology of the same area. Leonardon and Kelly' published a resistivity curve obtained over the Hettenschlag dome, and a further discussion of this same area was given by the Messrs. Schlumberger6 in a communication. Messrs. Alty6 described studies on salt deposits in which the single-probe method was used. sinerez7 mentions that electrical methods were tried over salt deposits in Spain. Geoffrey and Charrin8 show a resistivity curve obtained over marl, gypsiferous marl and salt which is similar to that obtained over the New Mexico salt deposits. Kelly9 reported resistivity work performed with the ground Comparaor of Zuschlag over the salt deposits near Syracuse, N. Y., where the Salina formation is at a depth of 700 to 800 ft. Some structural studies on the potash basin of Alsace are described by Poldini.10 Another single-probe resistivity study, made over salt deposits in New Mexico, is briefly described by Heiland,11 through the courtesy of Harry Aurand, of the Midwest Refining co, Geological Features OF Area Covered The area discussed in this paper is in Eddy County, southeastern New Mexico, a

Jan 1, 1946

By Charles V. Seastone

The hydro-electric plant of the Peninsular Power Co. is located at what is commonly known as Lower Twin Falls on the Menominee River. This location is about 3I/2 miles north of the city of Iron Mountain, Mich. The principal points of delivery of electric energy from this plant are in the mining regions adjacent to Florence, Wis., and Iron River, Mich., and in the cities of Iron River and Iron Mountain. The hydro-electric plant at Twin Falls and the substation of the Iron Mountain Electric Light & Power Co, are connected by a 6,600-volt transmission line carried on steel towers and steel poles, the latter being used within the city limits. The plant at Twin Falls and the substation at Iron River, about 36 miles distant, are connected by a 66,000-volt, duplicate, three-phase transmission line, supported on steel towers. At Iron River, are located a 1,500-kw. auxiliary steam plant, and the substation, from which the current is distributed to the mines in this vicinity. A description of the auxiliary plant, main and customers' substations, and of the main and secondary transmission lines, follows later in this paper. General Layout The relative location of the dam, forebay, and power house will be understood by referring to Fig. 1. The dam is constructed on a ledge of solid rock which forms Lower Twin Falls. This rock ledge offers an excellent location in that the height of the dam, and therefore the amount of concrete, are thereby reduced, and also in that practically no pumping was required in unwatering the dam site. The maximum head provided by the dam is 44 ft., with an average working head of from 40 to 42 ft. The other structures, including the substructure of the power house,

Jan 1, 1915

By W. D. Robertson, A. S. Tetelman

The technique of decorating dislocations was employed to investigate deformation and fracture resulting from Precipitation of hydrogen in Fe-3 pet Si single crystals. It is shown that cracks are produced on (100) planes inside crystals, as a consequence of the precipitation of hydrogen gas, either when crystals are quenched from a hydrogen atmosphere at elevated temperatures or cathodically charged with hydrogen at room temperature. Plastic deformation in the vicinity of cracks, observed as arrays of decorated dislocations, is in conformity with the calculated stress distribution about a crack containing an internal pressure, and the observations provide information permitting a detailed analysis of the mechanics of crack growth. The fracture characteristics of crystals containing internal cracks were evaluated at 25o and -196°C and the results are related to the mechanism of hydrogen embrittlement in terms of the growth of preexisting cracks. HYDROGEN in bee iron or steel produces two characteristic changes in mechanical properties: I), a decrease in ductility (macroscopic strain at fracture) that depends on temperature and strain rate, and 2), spontaneous fracture under static load that depends on time and apparent stress. Resolution of these phenomena into the microscopic processes that combine to produce the macroscopic effects is especially difficult in the Fe-H system in which the active component cannot be directly observed and only maintained in equilibrium with great difficulty in the temperature and pressure range in which embrittlement phenomena appear. As a result of these complications, verification of the numerous hypotheses'-5 that have been proposed to explain the microscopic mechanism of embrittlement depends on self-consistency with measured changes in macroscopic properties that are averaged over the volume of a specimen. It is obviously important to obtain a more direct evaluation of the microscopic processes that combine to produce embrittlement. Accordingly, the present investigation was designed to identify and observe, as directly as possible, the microscopic effects of introducting hydrogen into a bee crystal. It was concluded from a previous investigation6 of X-ray line broadening, produced by introducing hydrogen into pure iron at room temperature, that the only effect that could be associated with the introduction of hydrogen was plastic deformation; in particular, dilation of the lattice was not observed, within ± 0.01 pet, and no evidence was found that could be interpreted to support the idea7'* that hydrogen occupies tetrahedral interstitial sites in the iron lattice. The absence of lattice dilation is consistent with the extremely small solubility of hydrogen in bee iron9,10 (0.015 at. pet at 900oC and 1 atm pressure), and the evidence of plastic deformation is consistent with the fact that hydrogen, introduced by cathodic charging, eliminates the carbon yield point.11-13 Following this investigation, the immediate problem was to devise a method by which plastic deformation could be observed directly. The technique employed by Hibbard and Dunn14 to observe the movement of dislocations during bending and subsequent polygonization of Fe-3 pet Si single crystals was adopted and modified for the present purpose to include the observation of dislocation arrays in the volume of the crystal, and their association with the fracture process. EXPERIMENTAL PROCEDURE Single crystals of a high purity Fe-3 pet Si alloy, containing 0.007 pet C, were grown in vacuum by

Jan 1, 1962

The San Manuel district of Arizona was first prospected prior to the Civil War, but there was little or no production until 1881. Small operators tried to develop ore bodies from time to time after that without success. Then, in 1917, a drilling program was carried out; but it did not indicate a copper content of interest. Finally, in the 1940s, the U. S. Geological Survey drilled the property and obtained indications of a mineralized area. At that time, Magma Copper and its principal owner, Newrnont Mining Corporation, drilled many deep holes through the gravels and conglomerates and in 1948 proved an ore reserve of 367 million tons of 0.785% copper sulfide ore. Underground exploration and development were started in early 1948, and in 1953 design and construction of the surface facilities commenced. By the end of 1955 plant construction was completed. The ore deposit of disseminated pyrite, chalcopyrite, chalcocite, molybdenite, silver, and gold is in quartz monzonite porphyry gangue. Mine production, which is entirely underground, is by full-gravity block-caving. Initially, ore mined at a rate of 36,000 tpd was hoisted through two identical shafts. From the 5,000 ton coarse ore bins located at the collar of each shaft, the ore was hauled by a shuttle service rail- road in 100-ton bottom-dump rail cars a distance of seven miles to the rail bin. Fragmentation from block-caving supplemented by underground grizzlies at the loading stations controlled the oversize material to give a feed size acceptable to the two 7 ft standard Syrnons crushers. During operation, however, it became evident that a large amount of secondary breaking in the grizzlies was necessary to produce a suitable feed for the standard crushers. The decision was then made to install primary gyratory crushers on the surface adjacent to the shaft site ore bins. Under each 5,000-ton coarse ore bin, an 8ft by 20 ft (2.44 m by 6. 1 m) apron feeder transfers the ore to a 13 ft 6 in. by 10 ft (4. 1 m by 3. 05 m) grizzly set at 6 in. (152 mm) and sloped at 45 degrees. About 65% of the ore passes the grizzly and thus bypasses the 42 in. by 65 in. (1.07 m by 1. 65 m) Allis -Chalmers gyratory equipped with a Hydroset mechanism and having an open side setting of 5 ½ in. (140 mm). Grizzly undersize and crushed ore drop onto a 6 ft by 30 ft (1. 83 m by 9. 14 m) variable- speed apron feeder for transfer to a 54 in. by 90 ft 5 in. (1.37 m by 27.6 m) inclined conveyor equipped with a tramp iron detector. Indication of tramp iron automatically stops the conveyor and both apron feeders. When the iron is removed from the belt by the operator,

Jan 1, 1978

By E. De Golyer

The only known direct method of discovering oil deposits is by the drilling of test wells. Such exploration is always hazardous and generally very costly. The problem of the prospector, therefore, is one of selecting test sites that are favorably located and so to reduce the odds against his venture. Early in the history of the oil industry, it was realized that oil and gas deposits, other conditions being favor- able, were usually found in anticlinal types of structure. This very understandable and rational habit of occurrence furnished the first substantial clue to the prospector. Oil occurs in sedimentary rocks, and beds of such rocks are deposited originally in parallel planes. An anticline at the surface, therefore, could be accepted as an indication of an anticline in lower beds. Structural geology became the tool of the prospector, and by its use in the past two decades, the majority of the known important oil deposits of the world have been discovered. This is but an incomplete, and the simplest, statement of the problem. Nine-tenths and more of the important oil pools of the world belong to the great class of accumulations controlled by structural traps- anticlines, faulted structures, salt domes, etc.-but by

Jan 1, 1932

By ANDREW McVILLIAM, WILLIAM H. HATFIELD

AT the 1902 May meeting of the Iron and Steel Institute, the, authors presented a paper on " The Elimination of Silicon in The Acid Open-Hearth," wherein they recorded a few typical examples of certain Siemens charges out of a very large number specially watched for the purposes of that research. The main deductions drawn from those experiments have been accepted in all the intelligent criticism during or after the discussion on the paper. One opinion, however, was rigidly held by all who mentioned the matter, with the single exception, perhaps, of Mr. Lange, and that was the necessity for the attainment and the maintenance of an abnormally high temperature in order that the percentage of silicon in the metallic bath might increase, or that an unusually large proportion of silicon might be retained in the metal. The original decision was ar-rived at on the results of scores of trials, and has since been the subject of frequent experiment. The authors still retain their opinion that although, naturally, a higher temperature will accelerate the (probable) action between the carbon of the steel and the excess silica of the slag, they then fairly proved, and have now abundantly confirmed the fact, that around the temperatures occurring in Siemens steel-making practice the chemical composition of the slag, particularly with regard to its acidity, is the factor which determines whether the percentage of silicon in the molten steel shall increase or decrease. In the discussion in 1902 Mr. Saniter called attention to Mr. H. H. Campbell's work, and in the reply the authors also mentioned that of Messrs. Winder and Brunton of 1892, the two

Mar 1, 1905

By C. J. Frosch, J. A. May, H. G. White, C. D. Thurmond

Gallium phosphide epitaxial layers were grown from the vapor phase on undoped single-crystal galliurn arsenide substrates in silica tubes by an open-tube wet-hydrogen process. The epitaxial layers were grown over a range of water pressures at three substrate temperatures. Excess donor concentrations were determined by surface barvier capacitance measurelrzents without removing the layers from the substrates. The excess dmlor concentration, ND-NA, is fo~ind to vary approxilnately inversely with the pressure of water added to the hydrogen carrier gas. This is the relationship that would be expected for singly ionized silicon donors on gallium sites in extrinsic galliunz phosphide, with the silicon coming from the SiO generated by the reaction of hydrogen with the silica tube. An increase in the partial pressure of water in the hydrogen stream decreases the SiO pressure. The results indicate that ni, the intrinsic hole and electrmt concentration for gallium phosphide at the three substrate temperatures, is smaller than the concentration estimated from available data for the density of states effective masses and the energy gap. Mass-spectrographic measurements confirm that the dono?, introduced into gallium phosphide is silicon. The equilibrium concentrations of silicon in vapor-flown gallium Phosphide have been estimated from available thernzodynamic information that includes the solubility measurements of silicon in gallium phosphide in equilibrium with a gallium-rich liquid phase. Satisfactory agreement with the measured silicon concentrations is obtained. FROSCH1 has described an open-tube process for growing single-crystal Gap from the vapor phase by a GazO transport mechanism. The method depends upon the reaction of H20 in an H2 carrier gas with a heated source of polycrystalline Gap which provides the necessary vapor species. When the temperature of these vapor species is lowered, super saturation occurs and single-crystal Gap will deposit on a suitable substrate. Unintentionally doped single crystals of Gap grown by the wet H2 process in silica tubes are n type. Evidence is presented to show that the donor introduced is silicon, and that a qua si-equilibrium model accounts for the inverse dependence of the donor concentration on the water partial pressure and predicts the magnitude of the donor concentrations. Ainslie et al. experimentally showed a similar inverse relationship between the carrier density and oxygen pressure for GaAs. Emission-spectrographic analyses showed a decrease in the silicon concentration with increasing oxygen overpressure for GaAs. Cochran and Foster suggested the theoretical possibility of suppressing silicon contamination by using Ga20 generated by the reaction of gallium with water vapor. 1) EXPERIMENTAL The apparatus and procedures are essentially the same as those described by Frosch.' The apparatus consists of a 25-mm-ID SiO2 tube extending through a controlled high-temperature flat zone for the location of the polycrystalline Gap source and a downstream temperature gradient falling at a rate of about 14°C per cm. The latter provides the region of super saturation for the location of the single-crystal substrate. The partial pressure of water in the inflowing hydrogen stream, pA2, O was controlled by mixing me-tered proportions of dry H2 with H2 saturated with H2O vapor at 0°C. The total gas flows were about 200 cu cm per min in all experiments. The Gap sources were prepared by pulverizing boat-grown polycrystalline ingots to pass a 20-mesh sieve. The substrates were cut from an undoped single-crystal boat-grown GaAs ingot purchased from Monsanto. This ingot had a carrier concentration of about 1015 atoms per cu cm, a resistivity of about 5 ohm-cm, and a mobility of about 5000 sq cm per v sec at 25°C. Substrates with dimensions of 1 by 1 by 5 x lo-' cm were employed. The growth faces were chemically polished (111) arsenic faces. Epitaxial layers, at least 7.5 x 10-3 cm thick, were grown,. This required from 1 to 24 hr depending upon the Pii2Q values and the temperatures. In all of the runs, the source temperatures were 50°C higher than the substrate temperatures. Samples were prepared

Jan 1, 1968

By E. DeGolyer

The only known direct method of discovering oil deposits is by the drilling of test wells. Such exploration is always hazardous and generally very costly. The problem of the prospector, therefore, is to select test sites that are favorably located and so to reduce the odds against his venture. Early in the history of the oil industry, it was realized that oil and gas deposits, other conditions being favorable, were usually found in anticlinal types of structure. This very undestandable and rational habit of occurrence furnished the first substantial clue to the prospector. Oil occurs in sedimentary rocks, and beds of such rocks are deposited originally in approximately parallel layers. An anticline at the surface, therefore, could be accepted as an indication of an anticline in lower beds. Structural geology became the tool of the prospector, and by its use in the past two decades the majority of the known important oil deposits of the world have been discovered. This is but a partial, and the simplest, statement of the problem, Nine-tenths and more of the important oil pools of the world belong to the great class of accumulations controlled by structural traps—anti-clines, faulted structures, salt domes, etc.—but by no means all of these structures are clearly or adequately expressed at the surface. As the more obvious anticlines were explored and the search for new deposits led to the testing of progressively deeper beds, it became more and more apparent that marked favorable structures involving petroliferous rocks can, and do, exist without any marked surface expression. There are great areas where the surface, covered by some masking material such as water, alluvium, glacial deposits, or sand dunes, affords no clue to structural conditions in the subsurface, and there are also regions where the surface formations are unconformable with the oil-bearing formations. The structure in which the prospector is fundamentally interested is that of the oil-bearing formation itself, together with roof and floor beds. No other geologic information is of interest or importance to him except as it affords clues to the stratigraphy and structure of the supposed oil-bearing formations.

Jan 1, 1932

By J. B. Stubbins, R. A. Blais

Extensive geological work was initiated — and continues — when operations of the Iron Ore Co. of Canada commenced in the Labrador-New Quebec area. Such geological operations include: mapping, test pitting, drilling, underground workings, volume factor and structure tests, and the calculation of ore grades and tonnages. Details of such work are given. Development is carried sufficiently ahead of mining to provide reliable tonnage and grade estimates and allow final mine planning. In order to make full use of geology in mining operations, the pit engineer combines the duties of geologist and mining engineer. The iron deposits of the Knob Lake range are located in the central part of the Labrador peninsula, a territory nearly twice the size of Texas, which is bounded by Hudson Bay on the west, Hudson Strait on the north, the Atlantic Ocean on the east and the Gulf of St. Lawrence on the south. The mining district proper is about 1000 miles northeast of Toronto. A 360-mile railroad links this mining area to the port of Sept-Iles on the Gulf of St. Lawrence. Schef-ferville, which is only a few miles from the open-pit mines, is the center of operations of the Iron Ore Co. of Canada. It has a population of nearly 5000. The nearest settlement is Labrador City, some 120 miles to the south, where this company is erecting a large plant for beneficiating its huge reserves of local low-grade iron ores. HISTORY The mineral possibilities of the area were recognized as early as the end of the last century, when A.P. LOW' of the Geological Survey of Canada made his famous trek across the Labrador Peninsula. After mapping several belts of iron formation, Lovr recommended that the area be thoroughly prospected for iron. In 1929, two well known Canadian geologists, J.E. Gill and U'.F. James, led a private expedition in central Labrador and discovered the first deposit of high-grade iron ore near what is now the Ruth Lake Mine. In 1936 the Labrador Mining and Exploration Co. was formed to 11ake over a prospecting concession of over 20,000 sq miles in central Labrador. An adjoining concession of 3900 sq miles in New Quebec was obtained in 1942 by Hollinger Consolidated Gold Mines, which had just Purchased the Labrador Co. The same year the M.A. Hanna Co. Purchased an interest in both exploration companies. From 1942 to 1950 extensive exploration was conducted by the Hollinger-Hanna technical staff to systematically appraise these vast concessions. More than 40 deposits of high grade ore were found and, by the end of 1950, the total ore reserves reached 418 million tons. In 1949 five American steel companies joined the Hollinger-Hanna interests and formed the Iron Ore Co. of Canada. Financing and full-scale construction were decided upon in 1950. This included the construction of a 360-mile railroad through very difficult terrain, the erection of two hydroelectric plants, the installation of terminal port facilities at Sept-IIes, the building of a modern town-site at Schefferville, the construction of crushing and screening plants, and the preparation of deposits for mining. Ore was first shipped in July 1954. Total open-pit mine production to date is 66 million long tons of direct-shipping ore. GEOLOGICAL ENGINEERING The above achievements would not have been possible without irtegrated teamwork of people of diverse skills and extensive use of geology. In their paper on the role of geologists in the development of this iron ore field, (Gustafson and Moss1 rightly emphasized the difficulties facing the early workers in the area. In an uninhabited land with no roads or railroads and no navigable rivers leading to the interior, everything had to be flown in. It was not until 1948 that aerial photographs and adequate base maps became available. In spite of these and other difficulties, an impressive amount of field work has been done since 1942. Nearly all this work has been directed by geological engineers and geologists. About 15,000 :sq miles have been geologically

Jan 1, 1962