Search Documents

By Arthur L. Crawford

PLAGER gold is perhaps the most difficult of the common mineral deposits to evaluate. Not only are the erratic pay streaks a source of never-ending uncertainty, but the spotty distribution of the gold in iso¬lated nuggets is a perpetual source of error and disappointment to the sampler. Experienced engineers have long realized this difficulty and have been wary in predicting assay values except in the most general terms, and then only after extensive and usually expensive sampling. During the past year I have had the opportunity of checking a number of gold placers, and from the results obtained I believe that the microscope may be employed to advantage in placer sampling.

Jan 1, 1933

By D. K. Crampton

ON giving thought to the subject of this paper, my first reaction was that many and striking changes have come about as a direct result of the war. However, more careful analysis indicates that few, if any, of these changes can be wholly attributed to it. The actual situation is that all these changes were conceived and most of them at least partially executed in re- cent prewar years, it remaining the role of war to achieve results in a fraction of the time that might normally have been taken, lacking its driving impulse. The further discussion will therefore be with the premise that the individual changes have been greatly hastened rather than directly and primarily caused by any war conditions. Co-operation among copper alloy producers on production problems is agreed to be much worth while. The industry was too long noted for jealousy and secrecy as to equipment, methods, and even materials produced. Gradually, a more open and co-operative policy evolved but even just prior to the war the interchange of ideas was relatively cautious and limited. The need for a great increase in production in record time fostered a more co- operative attitude; exchange of ideas and experience concerning all phases of production increased tremendously to the benefit of the individual participants and thus the war effort, too. This more united effort has undoubtedly led to many specific improvements in process or equipment and these in turn to more rapid and economical operation than could have taken place on an each-for-himself basis.

Jan 1, 1944

By Owen Thornton

Recently equations have been presented by Rose and Bruce' and by Rose², showing how the relative permeability of a reservoir rock may be determined from the capillary character of the rock. In particular, equations were developed to show the relationship between capillary pressure and the effective permeability to the wetting phase in a poly-phase flow system. The equations are as follows (nomenclature the same as in the Rose and Bruce paper) Rose and Bruce assume that the average length of path (L,), which the wetting fluid follows in flowing through a porous media is independent of the saturation to the wetting phase, so that 1 is a constant dependent only on the k rock, and the permeability to the wetting phase is a function of the saturation and of the capillnry pressure: In measuring the flow of ekctric current through partially saturated core samples, it has been observed that the electrical resistance usually is not a simple linear function of saturation. This fact indicates that the average length of path in the flow of electric current is not independent of saturation, but rather that the tortuosity of the path depends upon the average saturation to the conducting fluid as well as upon the characteristics of the rock. itself. Inasmuch as the flow of fluid and the flow of electric current in many respects are analogous, it may be indicated further that the length of path for fluid also may not be independent of saturation. The following relationship can be derived to express the resistance to flow of electric current through a core sample partially saturated with conductive wetting phase, the non-wetting phase being non-conductive: where L is the average length of path followed by the current in flowing through a length L of partially saturated core, where L is the length of current path when the core is fully saturated, and where Rs and R, are the specific resistivities of the partially saturated and saturated core sample, respectively. It will be noted that R., the specific resistivity of the core sample when S, = 1.0, is equal to the "formation resistivity factor"' multiplied by the specific resistivity of the saturating fluid. If it be assumed that the average lengths of path for fluid flow and for the flow of electric current are the same, then equation (5) may be combined with equations (l), (2) and (3) to give the following relationship: The above equation suggests including a correction for tortuosity when calculating the relative permeability of a reservoir rock to a wetting phase. The correction factor may be obtained from the resistivity-saturation relationship. For instance, the following calcu- lations are obtained for the unconsoli-dated sands described by Leverett Kw Kw Sw R°/Rs Pt/Pc¹ (Calc.) (Obs.) 0.30 0.08 0.88 0.02 0.0 0.40 0.16 0.94 0.06 0.04 0.50 0.27 0.97 0.14 0.11 0.60 0.40 0.98 0.26 0.21 0.70 0.53 0.98 0.39 0.35 0.80 0.68 0.99 0.57 0.54 0.90 0.84 0.99 0.77 0.76 1.00 1.00 1.00 1.00 1.00 It will be noted that the agreement between the calculated points and the observed data is rather good. Further investigation of the above method for obtaining relative permeabilities may be merited. For many sands within specified ranges of saturations the following relationship has been found to hold approximately': — =SW"......(7) Rs The exponent n in the above equation has been found to equal two for many sands so that equation (6) reduces to the following: The writer acknowledges the permission of The Texas Co. to submit this note for publication. 1. Walter Rose and W. A. Bruce—Jnl. of Pet. Tech., Vol. 1, No. 5, p. 127 (1949). 2. Walter Rose—Jnl. of Petr. Tech., Vol. 1, No. 5, p. 111 (1949). 3. G. E. Archie— -Trans. AIME, 146, 54 (1942). 4. M. C. Leverett— Trans. AIME, 142, 152 (1941). 5. M. C. Leverett—Trans. AIME, 132, 149 (1939).

Jan 1, 1949

By Owen Thornton

Recently equations have been presented by Rose and Bruce' and by Rose², showing how the relative permeability of a reservoir rock may be determined from the capillary character of the rock. In particular, equations were developed to show the relationship between capillary pressure and the effective permeability to the wetting phase in a poly-phase flow system. The equations are as follows (nomenclature the same as in the Rose and Bruce paper) Rose and Bruce assume that the average length of path (L,), which the wetting fluid follows in flowing through a porous media is independent of the saturation to the wetting phase, so that 1 is a constant dependent only on the k rock, and the permeability to the wetting phase is a function of the saturation and of the capillnry pressure: In measuring the flow of ekctric current through partially saturated core samples, it has been observed that the electrical resistance usually is not a simple linear function of saturation. This fact indicates that the average length of path in the flow of electric current is not independent of saturation, but rather that the tortuosity of the path depends upon the average saturation to the conducting fluid as well as upon the characteristics of the rock. itself. Inasmuch as the flow of fluid and the flow of electric current in many respects are analogous, it may be indicated further that the length of path for fluid also may not be independent of saturation. The following relationship can be derived to express the resistance to flow of electric current through a core sample partially saturated with conductive wetting phase, the non-wetting phase being non-conductive: where L is the average length of path followed by the current in flowing through a length L of partially saturated core, where L is the length of current path when the core is fully saturated, and where Rs and R, are the specific resistivities of the partially saturated and saturated core sample, respectively. It will be noted that R., the specific resistivity of the core sample when S, = 1.0, is equal to the "formation resistivity factor"' multiplied by the specific resistivity of the saturating fluid. If it be assumed that the average lengths of path for fluid flow and for the flow of electric current are the same, then equation (5) may be combined with equations (l), (2) and (3) to give the following relationship: The above equation suggests including a correction for tortuosity when calculating the relative permeability of a reservoir rock to a wetting phase. The correction factor may be obtained from the resistivity-saturation relationship. For instance, the following calcu- lations are obtained for the unconsoli-dated sands described by Leverett Kw Kw Sw R°/Rs Pt/Pc¹ (Calc.) (Obs.) 0.30 0.08 0.88 0.02 0.0 0.40 0.16 0.94 0.06 0.04 0.50 0.27 0.97 0.14 0.11 0.60 0.40 0.98 0.26 0.21 0.70 0.53 0.98 0.39 0.35 0.80 0.68 0.99 0.57 0.54 0.90 0.84 0.99 0.77 0.76 1.00 1.00 1.00 1.00 1.00 It will be noted that the agreement between the calculated points and the observed data is rather good. Further investigation of the above method for obtaining relative permeabilities may be merited. For many sands within specified ranges of saturations the following relationship has been found to hold approximately': — =SW"......(7) Rs The exponent n in the above equation has been found to equal two for many sands so that equation (6) reduces to the following: The writer acknowledges the permission of The Texas Co. to submit this note for publication. 1. Walter Rose and W. A. Bruce—Jnl. of Pet. Tech., Vol. 1, No. 5, p. 127 (1949). 2. Walter Rose—Jnl. of Petr. Tech., Vol. 1, No. 5, p. 111 (1949). 3. G. E. Archie— -Trans. AIME, 146, 54 (1942). 4. M. C. Leverett— Trans. AIME, 142, 152 (1941). 5. M. C. Leverett—Trans. AIME, 132, 149 (1939).

Jan 1, 1949

By R. E. Boni, G. Derge

Application of surface tension measurements has been made to molten silicates in order to determine the effect of sulphur upon the surface tensions of synthetic blast furnace slags. In melts with the same molar ratios of AI2O3 + SiO2 to the basic oxides BaO, CaO, and MgO, the surface tensions increase in the order of oxides listed. Sulphur lowers the surface tensions of the basic BaO, basic CaO, acid BaO, acid CaO, and acid MgO slags in that order; and the concentration of excess sulphur at the slag surface increases in this same order of slags. The rate and amount of desulphurization of iron by these slags is favored by a low excess surface sulphur in the slag. IN a previous paper,1 the authors discussed the applications of surface tension measurements of molten silicates to problems of metallurgical interest. Of major importance is the aid that such studies lend to forming a working concept of slag structure. Since the ability of a slag to desulphurize metal depends strongly upon its composition,2"4 fundamental information about the structural differences between various slags which contain sulphur should aid the development of better desulphurizing media. For that reason, the present investigation concerns the effect of sulphur upon the surface tensions of synthetic blast furnace slags. Experimental Procedure , The maximum bubble-pressure method was used to measure the surface tensions of synthetic blast furnace slags in the temperature range 1300° to 1600°C. The method is based upon the equation which was developed by Schrödinger5 from a consideration of the forces of hydrostatic pressure and surface tension of a liquid which oppose bubble formation when a gas is forced through a tube immersed in the liquid. where y is the surface tension between argon and slag in dynes per centimeter; g is the gravitational constant, centimeters per second2; H is the manometer reading in centimeters; s2 is the density of manometer fluid in grams per cubic centimeter; S1 is the density of the medium in grams per cubic

Jan 1, 1957

By Lyman H. Hart

Some of the significant facts that will affect the supply and demand for metals during the next few decades are given in this presentation. This is important because the only hope for intelligent guidance of the national destiny depends upon presenting a consistent and accurate picture of basic problems. The metals problems now fomenting are only slightly less important than those precipitating the energy crisis. Admittedly, it is difficult to generate serious thinking on this subject when the world is enjoying easy access to all metals at modest prices. This is possible because of the current world capacity to over-produce, and United States credit standing, at least up to now, has permitted buying freely on world markets. Although both these vital conditions are subject to change, there is little doubt that if the U.S. financial house is kept in order, we can muddle along for a while on a generally expanding, metal-based economy. But should our credit standing be permitted to collapse, or should there be a tightening of world supplies of metals, the nation would immediately find itself in trouble. Unfortunately, clear signals indicate that both of these conditions are threatening. The metal age started many centuries ago, and with the exception of the noble metals, barely a dent was made in world reserves until the present century. Then, as a result of the pioneering ideas of D. C. Jackling and Paul Gemmel, and the willingness of the McNeals, Penroses and Guggenheims to back ideas with money, a virtual explosion of metal production was propagated throughout the world. It is important to examine the causes of this expansion to determine whether it is a trend that may be sustained or whether it is anomalous and therefore attributable to circumstances not likely to be repeated or continued. This period of plenty is a once only phenomenon. Vast metal resources have been sitting around here for eons, while the world was unaware of or unconcerned with their existence. But when population began to grow exponentially, and ways were discovered to use metals to develop machines to do the work of men and animals, the exploitation of raw materials increased at a staggering rate. And now the realization is dawning that minerals are a wasting asset and are beginning to present supply problems that should begin to be of concern. Two main factors have caused this condition; One is the population growth, and the other is the expanding demand for irreplaceable raw materials as nations become more developed. A group of systems analysts, at Massachusetts Institute of Technology in a book Limits of Growth, has warned that at present rates of population growth and resource consumption together with environmental constraints, a point will be reached within 100 years when the world population will become totally incapable of supporting itself. The authors conclude that this end result could be avoided if a planned equilibrium could be established at a lower rate of population growth and resource consumption. Fortunately, there is evidence that the population problem is moderating. The growth rate in the U.S. has decreased from 2.3% per year in 1900 to 1.1% in 1970. But, even at the lower rate, population will double in 70 years. The world rate is greater, and if it continues, world population will rise from 3.5 billion to nearly 10 billion in 50 years. All of these projections are questionable because the dangers of growing population are now being recognized. A marked decrease in growth rate has been noted in the more developed countries-in fact, it was zero in the U.S. in 1972. The other factor affecting consumption of raw materials is the increase in per capita use of most items as individuals become more affluent. Many economists believe that developing countries such as China and India represent a vast future potential market; but there are others, with whom the author agrees, who believe over-population tends to stagnate development. Nevertheless, it is a fact that vigorously developing societies increase consumption at a rate far above their population growth rate.

Jan 1, 1974

By C. W. Davis

THE name fuller's earth, which was derived from its early use in "fulling" or removing grease from woolen goods, is a term that is generally considered to designate mineral matter, containing hydrous aluminum silicates of the clay group, which has a high capacity for removing colors from oils, whether of animal, vegetable, or mineral origin. Fuller's earths are usually dried and may be "tempered" by heating or may be treated with water or reagents to improve their efficiency. For our purpose the term "acid-treated earths" will include those products from the partial decomposition of mineral water -by acid which are equal to or more efficient than an untreated fuller's earth from Quincy, Fla., when used in bleaching mineral oil by the "contact" process. In general, the contact process for treating oils consists of heating and agitating a mixture of oil and finely divided adsorbent, the latter being subsequently removed by filtration. The term "adsorbent" is used because, although there has been a great deal of controversy over the mechanism of removal of impurities from oils by mineral matter, there is no doubt that adsorption, which involves the surface of the solid, plays a major part.1 The properties that make fuller's earth useful in the treatment of petroleum products by "percolation" and in the purification of edible oils by the contact process have long been studied, but the comparatively recent adaptation of the contact process to the bleaching of petroleum products has made desirable the further investigation of fuller's earth and other, adsorbent earths.

Jan 1, 1929

By H. LeRoy Scharon

The electrical resistivity method was utilized at 245 road cuts and structure sites over the 166 miles of the Philadelphia and Western Extensions of the Pennsylvania Turnpike System. Varying geologic structures and rock types afforded an excellent academic study of the method as well as a practical application to modern highway engineering.

Jan 4, 1951

By E. Douglas Sethness

The uranium industry is booming. In Texas alone, there are about 22 different companies with active exploration programs. Twelve solution mines have been permitted; three surface mines have been authorized; and two mills are currently in operation. However, the industry also has a problem, and that is the disposal of radioactive wastes. Over the past several years, stories concerning nuclear wastes have appeared frequently in the news. One of the most frequently cited cases occurred in Grand Junction, Colorado. In 1966, after ten years of investigations, the U. S. Public Health Service (PHS) discovered that tailings from a uranium mill were being used as fill material and aggregate for local construction purposes. It was estimated that between 150,000 and 200,000 tons of material had been removed and used under streets, driveways, swimming pools, and sewer lines. In addition, tailings had been used under concrete slabs and around foundations of occupiable structures. Further studies prompted the Surgeon General to warn that the risk of leukemia and lung cancer could be doubled at the measured radiation levels. More recently, the L. B. Foster Company discovered that its building site in Washington, West Virginia, was radioactive. While digging a foundation, the ground erupted and a ball of fire 30 feet high shot out. Evidently, the dirt was laced with radioactive thorium and zirconium, a potentially explosive mixture contained in a Nigerian sand which had been used by the previous site owners in the manufacture of nuclear fuel rods. Just this month we have read about legal suits to stop exploration for a nuclear waste disposal site in Randall County, Texas. The U. S. Department of Energy is trying to locate a deep underground nuclear waste depository for final burial of over 76 million gallons of high-level wastes. The problem is acute, the wastes are accumulating at a rate of about 300,000 gallons per year. Nor do these numbers include the spent fuel elements from nuclear power plants that are in temporary storage facilities. Fortunately, public awareness of these and other related issues is high. Unfortunately, the differences in the waste products from the nuclear fuel cycle are not always apparent to the general public. There are two distinct types of radioactive wastes: "high-level", which consist of spent fuel or wastes from the reprocessing of spent fuel; and "low-level", which, in general, are by-product wastes. There are numerous non-technical definitions that can be applied to help the layman differentiate between high-level and low-level wastes. For this latter purpose, it is best to think of them in terms of what we can see and feel. In general, high-level wastes are physically hot and can cause acute radiation sickness in a short period of time. Low-level wastes are not hot, but may cause chronic health effects after long exposure. The wastes which we are concerned with in the uranium mining and milling industry are low-level wastes. As recently as ten years ago, there were very few controls or regulations governing tailings disposal methods. At the same time, mine reclamation was not enforced through either state or Federal laws and the long-term viability of abandoned tailings ponds was not assured. The regulatory climate has changed significantly in the last decade, however. The low-level radioactive wastes generated by uranium mining and milling are generally contained in a tailings pond. Approximately 85-97% of the total radioactivity contained in uranium ore is present in the mill waste that goes to such tailings ponds. The isotope Radium-226 is probably the most potentially harmful radioactive parameter in the ponds. Radium emits gamma radiation and is also an alpha particle emitter. Because gamma radiation is very penetrating, it presents a potential health problem when a source is located external to the body. Gamma radiation will go through the body, causing damage to each cell encountered on the way. Although alpha particles have very little penetration capability, they can cause extensive cell damage. For this reason, alpha particles are a problem after inhalation or ingestion. Radium creates a health hazard by both of these mechanisms. Radium decays to radon gas which can be inhaled and serve as an alpha particle emitter. Additionally, radium is very soluble and readily enters the natural hydrologic cycle if allowed to leach from a tailings pond. With a half-life of 1620 years, radium has plenty of time to be taken into the food chain and end up in our bodies, emitting alpha particles. Because the potential health problems are better understood today than ten years ago, and because the Nuclear Regulatory Commission (NRC) has developed increasingly stringent government regulations, the uranium mining industry applies a high level of technology to the disposal of nuclear wastes. In most cases, low-level radioactive wastes are disposed of at or near the site where they are produced. There are six commercial burial grounds for low-level wastes, but it would not be economical to ship all mine or milling wastes to these sites. The on-site disposal methods most often used are ponding

Jan 1, 1979

By Allan D. Taylor

INTRODUCTION From the designer's view, the installation starts with the first definition of the orebody, and progresses through a long and complex development. The design is affected not only by the characteristics of the ore, but by all of the personalities and events of the project during its development. The following discussion attempts to touch on the most important aspects which define the context in which the designer must work in apply the do's and don'ts. That context is the basis of the viewpoint. WHAT CAN GO WRONG The Project Is Going Over Budget This is a common and serious concern to the plant designer. The Project Falls Behind Schedule Another common and disturbing condition with which the plant designer must cope. Some Equipment Fails to Perform This can be due to either faulty equipment or operating deficiencies. It can be the result of a wide variety of causes, but the designer will be an interested party in the search for the cause and the cure. The Plant Isn't Flexible Enough Sometimes a plant will handle some or even most of the ore satisfactorily but is unable to treat another type properly. This can be a significant problem. An example might be a case where low capacity of a cyclone feed pump makes it impossible to accompany an increase in grinding mill throughput with a corresponding increase in dilution water. This could lead to an increase in cyclone feed density, and a loss in product grade or a limit on the plant capacity. Spillage And Cleanup Are Excessive This is one of the most common and annoying defects in metallurgical plants, and one for which the designer can rarely delegate blame. Maintenance Is Excessive Another common complaint in new plants, and also one for which the dedesigner must accept most of the responsibility.

Jan 1, 1982

By William N. Poundstone

What attracts young engineering graduates into the coal industry? What do these young men expect of a career in coal mining? These questions are often asked and debated by mining men throughout the country. In order to present a comprehensive answer to them, an opinion survey was conducted at West Virginia University's School of Mines among the junior and senior classes and part of the sophomore class. The tabulation of the answers showed that the present-day mining engineering student is an older, more mature individual as compared with former years and as compared with other present-day college students. The average age of the country's record-breaking 150,000 college graduates is 24 years. Among this year's mining graduates at West Virginia University, 78% are of this age or older. Over half (54%) of those polled in the survey are married. This is com- pared to 30% as a national figure. Of those married, 38% have one child and over 6% have two children. The entire senior group covered by this survey has averaged almost three years in the armed forces. An article entitled "The Class of '49" in the June issue of Fortune magazine states that this year's class is the oldest, most mature class in history. Our survey indicates that the mining engineering students at West Virginia University are well above the average in this respect.

Jan 1, 1949

By Lyman H. Hart

Some of the significant facts that will affect the supply and demand for metals during the next few decades are given in this presentation. This is important because the only hope for intelligent guidance of the national destiny depends upon presenting a consistent and accurate picture of basic problems. The metals problems now fomenting are only slightly less important than those precipitating the energy crisis. Admittedly, it is difficult to generate serious thinking on this subject when the world is enjoying easy access to all metals at modest prices. This is possible because of the current world capacity to overproduce, and United States credit standing, at least up to now, has permitted buying freely on world markets. Although both these vital conditions are subject to change, there is little doubt that if the U.S. financial house is kept in order, we can muddle along for a while on a generally expanding, metalbased economy. But should our credit standing be permitted to collapse, or should there be a tightening of world supplies of metals, the nation would immediately find itself in trouble. Unfortunately, clear signals indicate that both of these conditions are threatening.

Jan 4, 1973

By Kenneth A. Moon

An exact statistical treatment of a one-dimensional model is used as a basis for evoluating the reliability of certain simplified expressions for the activity of the solute in interstitial solutions, including one obtained from the exact expression by setting the repulsive interaction equal to infinity. The latter approximation is found to be satisfactory at low and moderate concentration if the repulsive interaction is large, even though not infinite. A similar expression (identical if the co-odination number is two) is derived from the quasichemical expression of Lacher, and is recommended as the best available expression for the excess configurational entropy of interstitial solutions with excluded sites. Some reasonable models are discussed, and the nature of the saturated solutions is determined by inspection. Some of the models reduce to the one -dimensional case. An analysis is given of the excess partial entropy of hydrogen in V-H; Nb-H; and To-H solutions. MOST treatments of the statistical thermodynamics of interstitial solid solutions have followed the classic paper1 of Lacher in making the simplifying assumption that the configurational entropy of the solution is ideal. However, it is becoming increasingly apparent that there are many interstitial solutions with very large so lute-solute repulsions, and for these the assumption of ideal entropy is not valid or useful. It is important to realize that with substitutional solutions large repulsions between the component atoms must lead to phase separation, whereas in interstitial solutions the free energy of the solution is not drastically increased by large solute-solute repulsions until intrinsic saturation is reached at the concentration where further solute would be forced to enter a site in which it would experience the repulsive effect of one or more solute atoms already present. In the limiting case of an infinitely large repulsive interaction, the excess free energy would be attributable entirely to excess entropy, the enthalpy of mixing being zero. AS will be shown below, even if the repulsions are less than infinite, a treatment based on an assumption of infinite repulsions may be very satisfactory up to moderately high concentrations of the interstitial component. Often in solutions where large repulsive interactions exist, there are also small interactions — often attractive—between solute atoms in configurations other than that corresponding to the large repulsion. In such cases the excess free energy will consist of an excess entropy term attributable to the large repulsive interactions, and an enthalpy term corresponding to the other small interactions. Nomenclature to differentiate succinctly between important cases would be a convenience. In this paper the nomenclature shown in Table I will be used. In Table I, and in the preceeding discussion, excess quantities are defined in terms of standard states which are pure solid solvent and pure (possibly hypothetical) solid saturated phase of the structure in question. In practice, it is more convenient to choose the interstitial element as a component, and its conventional standard state. This will add a composition-independent term to the excess entropy and the enthalpy. The earliest paper known to the present author which treats the thermodynamics of athermal interstitial solutions was given by schei12 in 1951, but the statistical derivations in that paper are open to criticism. Speiser and Spretnak were the first to give a correct statistical treatment,3 limited, however, to concentrations sufficiently low that the number of empty sites excluded from occupancy by more than one filled site is negligible. The purpose of the present paper is to extend the statistical treatment to more concentrated solutions, and to examine the magnitude of the errors introduced by assuming that the repulsive interactions are infinite when in fact they must be finite. THE QUASICHEMICAL APPROXIMATION Fortunately, a standard method already exists for taking into account the effect of large interactions upon the entropy of mixing. This is the quasi-chemical method, in which the probability of existence of a given pair of solute atoms in a certain proximate configuration is assumed to be proportional to exp(-w/kT), where w is the energy increase of the solution when the two atoms are moved from isolated locations in the solution to the configuration in question. A quasichemical treatment of interstitial solutions was given in 1937 in a widely neglected paper by Lacher.4 The result comes out

Jan 1, 1963

By J. H. Polhems, R. B. Brackin, D. B. Grove

THE heavy media separation process plays an outstanding role in the concentration of 4000 tons of zinc ore per day at the Mascot mill of the American Zinc Co. of Tennessee. Of the total tonnage, 72 pct is treated in the heavy media separation plant to reject 56 pct of the ore as a coarse tailing, which has a ready market. Concentrates from this separation are beneficiated further by jigging and flotation. Approximately 25 pct of the total zinc concentrate production is made in the jig mill. Jig tailings are ground and pumped to the flotation circuit where the balance of the production is made. Fig. 1 shows a generalized flowsheet of the mill. The Mascot ore is a lead-free, honey-colored sphalerite in dolomitic limestone, with lesser amounts of chert and some pyrite. A mineralogical analysis is given in Table I. After 10 years of successful operation with galena medium and treatment of nearly 10,000,000 tons of ore, a decision to convert to ferrosilicon was made early in 1948 because of the increasing price of galena and consequent high operating costs. The conversion was made on Nov. 6, 1948, and the results obtained since that time have shown remarkable improvement over those made with galena. The Table I. Mineralogical Analysis of Mill Feed, Pct Calcium carbonate 49.5 Magnesium carbonate 35.2 Iron oxide and aluminum oxide 1.5 Zinc sulphide 4.5 Insoluble 9.3 100.0 Table II. Comparative Data, Galena and Ferrosilicon Ferro- Diner-Gelenaa siliconb ence Operating costs per ton milled, ct. 21.21 9.12 12.09 Medium consumption per ton milled, lb 0.80c 0.15 0.65 Reagent consumption per ton milled, lb 0.45 0.02 0.43 Tailing assay, pct Zn 0.310 0.297 0.013 Concentrate. oct Zn 12.08 10.33 1.75 Heavy medla ieparatlon recovery. pct 89.38 90.22 0.84 Mill feed rate, tons per hr 153 166 13 Heavy mesa separation feed rate. tons per hr 100 10 0 Tons milled per heavy media separation man shift 350 620 270 Mill feed to coarse tailings, pct 51.0 56.7 5.7 Lost mill time, pct 5.6 5.0 0.6 Power consumption, kw-hr per ton 2.06 1.92 0.14 a 1947. " First 6 months of 1950. c Net consumption after deducting credit for reclaimed waste galena. Consumption of new galena was 1.320 lb per ton milled. For entire life of galena operation, a credit of 40 pct of the value of the new galena added was realized from the sale of waste galena. comparisons given in this report cover the first 6 months of 1950 as representing the ferrosilicon operation, and the year 1947 as representing the galena operation. This was the last full year in which galena was used exclusively and is representative of the best work done during the 10 years of operation with this medium. After only 2 years' operating experience, with ferrosilicon and treatment of 1,807,585 tons many advantages have been revealed and are summarized in Table 11. Development Prior to the introduction of the heavy media process, all the mill feed was crushed through 5/8 in. and treated by jigging. A finished tailing assaying 0.66 pct Zn was made on rougher bull jigs, and cleaner jig tailings were ground for treatment by flotation. The first test work on the sink-and-float method of mineral beneficiation was carried out at Mascot in 1935, using a 3-ft cone and galena medium for batch tests. The following year a 6-ft cone was installed for pilot-plant work. This unit became a part of the mill circuit on March 1, 1936, and handled a gradually increasing tonnage in the next 2 years as the process developed to the point where it could treat all the + 3/8-in. material in the mill feed. Coarse jigging was then discontinued on March 1, 1939, and all coarse tailings have been made by the heavy media separation plant since that time. Feed Preparation: The original feed preparation plant consisted of a drag washer followed by two 4x10-ft Allis-Chalmers washing screens. A surge bin and two additional 5x12-ft AC washing screens were added in 1943. Use of primary and secondary washing screens was found essential to provide the cleanest possible feed for the cone and thereby avoid excessive contamination of the galena medium. Improved washing was obtained by replacing the drag washer with a 7x20-ft Allis-Chalmers scrubber, shown in Fig. 2, which has been in service since May 1944. Throughout the life of the galena operation, delivery of extremely muddy ore to the mill overloaded the medium cleaning system, and it frequently was necessary to cut off the feed and clean the medium for several hours until its normal viscosity had been re-established. The cleaning circuit

Jan 1, 1952

By Newell G. Alford

With the workable area of coal prospected and known as to workability and quantity and sampled and tested for desired quality comes the determination of the projection and method of working. The best method will be the one supplying the greatest degree of safety, the most merchantable product, the minimum average cost per ton with the largest yield of recoverable coal. Based on coal elevations, taken at the bottom of the seam on all known outcrop exposures, prospect openings or drill holes, coal contours are made on the map to be used in developing the mining plan. The contour interval should be as close as available information will permit. For general utility in layout of mining, haulage, drainage and ventilation, a map scale of 400 ft. per in. is preferable. In mountainous sections, location of the main out- crop opening or hoisting shaft is often limited by the available railroad route and amount of land level enough for a plant site. In level country, where a tipple and hoisting shaft may be placed at will, choice of the plant site should depend on the minimum average underground haul for the total coal to be worked to the new

Jan 1, 1932

By W. H. C. SIMMONDS

The mining, metallurgical, and petroleum industries can be viewed as financial or as social institutions or both. The differences between these two conceptions of their businesses will influence their environmental 'and social actions. During the next 10-20 years western industry will be subject to a drop in the growth of a more highly educated labour force and to the emergence of holistic economics, new national goals, and a new ecological perspective. The profitability of the mining industry may therefore be influenced by the human side of its business to a greater degree. The increasing human, social, and environmental responsibilities can be discharged by improving the miner's equipment; by learning to look at situations through the eyes of all those involved; by developing common 'languages' which governments and the public can understand; and by mediating where feasible on the international scene.

Jan 1, 1978

By M. L. Rudee, R. A. Huggins

Samples of iron containing nitrogen or carbon have been given treatments similar to those used in cold-work peak (CWP) measurements and examined by transmission electron microscopy. It was observed that the unusual and nonreproducible behavior of the carbon CWP can be explained by a strong tendency for carbon to form grain boundary precipitates at temperatures below those used for CWP measurements. These precipitates dissolved at the temperatures used in the CWP measurements. There was no evidence for nitrogen precipitation at grain boundaries. There was no indication of precipitation along dislocations in either carburized or nitrided samples given treatments similar to those of CWP measurements. Although it is possible that subelectron-microscopic clustering had occurred, this observation supports the theories of the CWP that are based on continuous atmospheres rather than on individual precipitates. In an earlier paper,' the present authors developed a new distribution function to predict the occupation of sites for interstitial impurity atoms around a dislocation. When this distribution was applied to the case of carbon and nitrogen in iron, it predicted that, if the temperature dependence of the concentration of solute atoms in the matrix was controlled by the presence of equilibrium carbide or nitride precipitates, the tendency for nitrogen to segregate to dislocations would be greater than that for carbon even though their binding energies to dislocations are identical. The cold-work internal-friction peak (CWP) is considered by most authors to be produced by the interaction of interstitial impurities with dislocations. Many investigators have studied the CWP in iron containing carbon and nitrogen and have observed a significant difference between its behavior in the two cases. In this paper a series of experiments will be reported that were initiated to determine whether the application of the new distribution function would explain the observed differences between the carbon and nitrogen CWP. Although it was found that the distribution function, pev se, did not explain the differences, the differences became clear, and some insight into the mechanism of the CWP was realized. Before reporting the present experiments, the literature pertaining to the differences between the carbon and nitrogen CWP in iron and the various mechanisms proposed for the CWP will be reviewed. LITERATURE REVIEW Snoek2 first observed the CWP in iron specimens containing nitrogen, but also reported a weak and unreliable peak in carburized samples. Later, Ke3 established that the CWP height was proportional to the degree of deformation. The presence of nitrogen alone would produce a peak of the same size as found in a sample containing both nitrogen and carbon, and KG concluded that the CWP was caused by nitrogen. In a discussion of G's paper it was reported that Dijkstra had investigated the CWP in samples that contained only carbon. He found it to be much smaller than the nitrogen peak and "unstable". KG et al.4 charged specimens of iron with both carbon and nitrogen. They observed that the carbon CWP was much smaller than that observed in nitrided samples, but that aging at 300°C caused the carbon peak to increase. A similar treatment produced no change in a nitrogen peak. Annealing at higher temperatures caused the height of the CWP in both the nitrogen and carbon samples to decrease. This behavior was also observed by Kamber et al. 5 who found that the activation energy for the annealing of the CWP was identical with the activation energy for the self-diffusion of iron. They concluded that the annihilation of dislocations by climb caused the reduction in the CWP height. Kamber et al. studied the "unstable" carbon peak in detail. They measured both the Snoek and CWP during various aging treatments. In carburized samples, aging at 100°C caused the Snoek peak to disappear, although the CWP peak remained small. However, a subsequent treatment for 5 hr at 240°C caused the CWP to reach a maximum. They proposed that an additional location for the carbon, other than whatever site produced the CWP, is present. In nitrided samples the CWP was completely developed as soon as a measurement was made; additional sites are not present. No explanation of either the additional site or the difference in the behavior of carbon and nitrogen was offered. petarra5 performed a systematic study of the effect of composition on the CWP. Using three kinds of "pure" iron, he showed that there was a residual CWP when the carbon and nitrogen concentrations had been reduced to less than that detectable by Snoek-peak measurements. He observed the same general annealing behavior and composition dependence as previous investigators, with the following exceptions. On first measuring the carbon CWP, it was found to be identical with the residual peak, and essentially independent of the carbon content. If the CWP was measured a second time in the same sample, it increased in size, but was still only about one-fourth the size of a CWP in a sample of the same iron nitrided to the same composition. On the other hand, a series of annealing experiments showed that the nitrogen CWP was not al-

Jan 1, 1967

By M. C. Manderson

Abstract-The sharp drop in world phosphate demand that took place in 1975, due to temporarily high prices, now seems to be reversing itself. And prices for both phosphate rock and phosphate fertilizers, which declined dramatically from their 1975 highs, now appear to be bottoming out. This recent price weakness has delayed new mining ventures that had previously been planned for completion by around 1980. While there is ample capacity to supply near-term rock needs, the stage seems to be emerging for a better supply-demand and price environment in the late 1970's and early 1980's.

Jan 1, 1978

By Peter Tegart

The discovery of gold in the Toodoggone River area is credited to Charles McClair who mined placer deposits in 1925, reportedly valued at $17,500. After he and his partner went missing in 1927, efforts to relocate their workings resulted in the formation of Two Brothers Valley Gold Mines Ltd. in 1933, in which the legendary Grant McConachie (first president of CP Air) played an active role. This was the age when the prospector first utilized the airplane to reconnoitre remote areas. What greeted the observer from the air was an area rich in orange and yellow colours characteristic of gossans formed by the oxidation of sulphides. However, Samuel Black, a Hudson Bay Company fur trader, had also noted in his diary as early as 1824, the unusual and many gossanous colours in the headwaters of the Finlay River. These gossans, coupled with white limestone bluffs and the presence of placer gold, attracted the first reconnaissance of the area by Cominco in 1929. Cominco was ever active in remote areas at this time. They staked and worked several base-metal showings hosted by limestone at the margins of intrusive stocks. These early workers also obtained erratic high gold assays from chalcedony float samples found in creeks draining into the Toodoggone River. However, because the samples gave inconsistent assays, no concerted effort was made to locate their source. Except for the occasional horse-supported prospecting party of the late 1940s and early 1950s, the area did not receive much attention until 1968. Work until this time focused on the base metal lead-zinc showings which contained attractive silver credits. Gold was not an attraction because of the set price established by the US government. The late 1960s saw the northward expansion of porphyry copper exploration into the Toodoggone. A program of gossan soil sampling (gossans which had attracted the early workers) was carried out by Kennco Explorations (Western) Ltd. in 1966-1967. They analysed for base metals in the field, using a cold extraction method. The Kemess copper- gold prospect was staked as a result of anomalous copper values from this early geochemical program. In 1968, Kennco continued the program of silt traversing and field geochemical testing. The samples were further subjected to multielement analysis consisting of copper, molybdenum, lead, zinc, cobalt, nickel, and silver at Kennco's North Vancouver laboratory. Several anomalous creeks, high in combinations of copper, molybdenum, and silver, were outlined. Some initial soil grids were also established. The fall of 1969 saw the return of Kennco prospector Gordon Davies and geologist Bob Stevenson to check out a well-defined molybdenum, scattered copper and silver anomaly in soils from a grid on the Chappelle claims. The subsequent analysis of several selected quartz felsenmeer floats yielded one assay which ran in the order of 0.25 kg/t (8 oz per st) gold and 2.2 kg/t (70 oz per st) silver. Subsequent trenching on the Chappelle claims exposed the source of float in a 4- m (134) wide vein of high grade gold-silver mineralization. These results led quickly to the realization that the district had precious metal potential. Subsequent exploration in the period 1969-1974 by Kennco resulted in the discovery of most of the gold and silver occurrences on the Chappelle and Lawyers properties. Several other gold and silver occurrences were found in this district by Cordilleran, Cominco, and Sumitomo, working the district during this period. Conwest optioned the Chappelle in 1973 and explored underground by adit entry as part of a one-year program. In 1974, Du Pont of Canada Exploration Ltd. optioned the Chappelle claims and in March 1980, using reserves developed on the A vein, placed the Baker mine into production at a rate of 90.7 Vd (100 stpd). The Amethyst zone on the Lawyers property, 8 km (5 miles) north of Chappelle, was found in 1973 by Kennco using continued, persistent followup prospecting of silver silt geochemical anomalies. A silt anomaly in the order of 3.4 ppm silver occurred in a stream flowing 300 m (984 ft)

Jan 1, 1985

By S. W. MEALS

TWENTY million people in this country and Canada in nearly four million homes can give thanks to our Creator for natural gas, that most wonderful natural fuel with which Dame Nature has so bountifully blessed us. It is a clean, healthy and cheerful fuel, made up almost entirely of carbon and hydrogen. There is no residue, no waste and there are no objectionable constituents; an ideal fuel for the home. It operates like magic, open the valve and it is there for your needs, winter or summer, night or day. You are not required to place your order 30 to 90 days in advance and you do not need to pay for your winter's supply in advance. No ashes to worry about, no flues or chimneys to clean, nor kindling wood to store or bother the housekeeper. We who have been so blessed do not realize what it would mean to be without it. If in place of opening a valve we had to go to the woodshed or coalhouse and then build our fire-carry out the ashes-well, some of us I am afraid would be late reaching our offices and perhaps would miss our hot cakes for breakfast. One cubic foot of gas produced from the White Sand formation contains 1130 B.t.u. and weighs 47/1000 lb.; there are about 24,000 B.t.u. in 1 lb. of gas. Temperatures of over 3400 deg. Fahr. have been obtained with natural gas. Not only is it a superior fuel for the home but it has no equal for use in many large manufacturing industries, especially with the making of glass, pottery and open-hearth steel. In an open-hearth furnace, properly constructed, 5000 cu. ft. will melt one ton of steel. It requires 1/3 ton of bituminous coal gasified in a producer to do the same work, or about 40 gal. of tar or fuel oil, or 11,000 cu. ft. of by-product gas.

Jan 1, 1926