Search Documents

By R. I. Jaffee, H. P. Nielsen

In recent years much attention has been given to high melting alloy systems. It has been of interest in this respect to investigate the alloys of platinum and tungsten, which were known from the literature to have very high melting points up to about 50 pct tungsten, but about which little had been published on the high-tungsten side of the system. Powder metallurgical methods were used throughout this investigation for the preparation of the alloys, utilizing electrical sintering techniques such as are used for tungsten and molybdenum. In the course of the work it was found desirable to determine fusion temperatures of the alloys, and it was possible from these and other data to draw a tentative constitutional diagram (solidus, mostly) applicable to the high-temperature part of the system. No attempt was made to determine solid solubility vs. temperature data, nor to investigate the lower temperature transformations in the solid state. Data on the microstructure, hardness, and a note on oxidation resistance of the sintered alloys were obtained. Past Work Miillerl determined liquidus temperatures of platinum-rich alloys to 50 pct tungsten, using a radiation method employing a photoelectric cell, and found that the melting points increased progressively from I771 C for platinum to 2350°C for the 50 pct alloy. Microscopic evidence by Miiller that complete solid solutions exist to 50 pct tungsten was not checked by Kremer2 who, according to Vines and Wise,3 found that "although the 8 pct tungsten alloy was a solid solution, the 26 pct tungsten alloy contained a eutectic or an intermediate phase." Hultgren and Jaffee4 using X ray methods found continuous solid solutions to at least 33.6 pct tungsten (35 at. pct) after annealing in vacuum for 6 days at I000 C. Vines and WiseS report work communicated to them by E. C. Rhodes on wrought alloys to 7 pct tungsten, which showed that tungsten hardened platinum extremely rapidly, and was one of the most potent hardeners of the binary additions to platinum. Considerable quantities of 4 pct tungsten platinum wire have been produced for grids in radar tubes and for aircraft spark plugs. Some of the alloy for the latter application is made by sintering, the remainder by smelting and casting. Materials The platinum powder used in this work was kindly supplied by the Research and Development Laboratory of the Owens-Corning Fiberglas Corp., Newark, Ohio. It was prepared from scrap platinum. After dissolving in aqua regia and evaporating almost to dryness, the solution was worked up several times with concentrated HC1. The resultant platinic chloride was diluted considerably, and metallic zinc was added, which precipitated the platinum in a very finely divided form. After dissolving the

Jan 1, 1949

By R. D. Pehke, J. F. Elliott

The solubility of nitrogen in liquid pure iron has been measured as a function of pressure and temperature. Sieverts' Law is obeyed at all pressures up to 1 atm and the temperature coefficient of solubility is 8 x 106 %/°C. The solubility of nitrogen in liquid iron alloys has been studied by the Sieverts' method and by the sampling method. The solubility is decreased by Al, C, Co Cu, Ni, 0. Si atzd Sn, and it is increased by Cr, Cb, Mn, Mo, Ta, W, and V. Interaction coefficients eN, for the effect of these elements on nitrogen dissolved in liquid iron, are reported. 1 HE effect of nitrogen upon the properties of steel may be desirable or not, depending upon the composition, processing treatment, and the use of the product. To understand the behavior of nitrogen in the various steelmaking processes, it is necessary to have reliable fundamental data pertaining to the solubilities, rates of solution, and chemical reactions of nitrogen in steel, particularly in the liquid state. In an effort to extend our knowledge in these areas, an investigation of the thermodynamics and kinetics of the solubility of nitrogen in liquid iron alloys was undertaken. The thermodynamic aspects of the study are presented in this paper. The solubility of nitrogen in liquid pure iron has received the attention of several investigators whose results are summarized in Table I. Reasonable agreement among the more recent researches1-l8 is found for the solubility of approximately 0.044 wt pct at 1600°C and 1-atm pressure of N,, for the temperature coefficient of solubility being small but positive, and for adherence to Sieverts' law for pressures up to 1 atm. The solubility of nitrogen in a number of binary liquid iron alloys has been studied: Fe-A1,3 Fe-As,16 Fe-C,3, 71 18, 19, 20 Fe-Cr ,5,7, 10, 11, 15 21 Fe-Co,'4, '6 Fe-Cu,'6 Fe-Mn,10, 11, 18 Fe-Mo,13, 16 Fe-Ni,10, 11, 13, 15, 16 Fe-O,16, 17, l9 Fe-p,7 Fe-S,l6 Fe-Sb,16 Fe-Se,lg Fe-Si,4) 97 '77 187 19>2° Fe-Sn,16 and Fe-v.51 '3 A few ternary systems have been studied, most of which were reviewed by ~angenberg" who applied the methods suggested by WagnerPz3 Chipman,24 Darken and G~rry, and Morris and Buehl26 for predicting solubilities in multicomponent alloys. Langenberg22 and Humbert and Elliott15 compared the solubilities computed from simple binary alloy systems with experimental measurements of nitrogen solubilities in liquid iron containing two or more alloying elements. The interaction coefficients for nitrogen in

Jan 1, 1961

By I. W. L. Finlay, H. R. Ogden, R. Jaffee, D. J. Maykuth

Aluminum has been found to be soluble in a titanium to about 26 pct, and to raise the temperature range of transformation from a to 8. Two intermediate phoses exist in the system, a new face-centered tetragonal phase, designated as 7, which occurs between 34 and 46 pct Al, and TiAI Metallographic and X-ray diffraction data were used to determine the diagram. ALUMINUM is one of the useful alloying additions for titanium-base alloys. It is an important constituent in two commercial alloys released in 1950, one containing 4 pct A1 and 4 pct Mn, and the other containing 3 pct A1 and 5 pct Cr as the metallic alloy content. It is probable that, in the future, other titanium alloys containing aluminum will be released. In the course of alloy development work, some of the features of the constitution of titanium-rich Ti-A1 alloys have been developed. These are described in the present paper. The only available information on the Ti-A1 system concerns the aluminum-rich end of the diagram. In summarizing the early work, Hansen' indicated that there is little solubility of titanium in aluminum, and that a two-phase region exists up to the intermediate compound, TiA1a (37.2 wt pct Ti), which has a congruent melting point at 1355°C. Fink' has reported that a peritectic reaction occurs at 665°C between the melt and TiA1³ to form the terminal solid solution of titanium in aluminum. The solubility of titanium in aluminum has been established at 0.24 pct at 510°C and is estimated to be between 1 and 1.5 pct at the peritectic temperature. No information has been published on the diagram above TiAl,, other than a statement- hat aluminum raises the a to ß transformation temperature of titanium. Materials and Preparation of Alloys Iodide-type titanium and high-purity aluminum were used in this investigation. Typical analyses of these materials are given in Table 1. Alloys were prepared by arc melting on a water-cooled copper hearth, using the techniques described previously for contamination-free melting.' Weight losses during melting were very low, ranging from 0 to 0.02 g in a 10 to 15 g charge, indicating that little or no loss of aluminum occurred during melting. This permitted the use of nominal compositions for these alloys. Alloy ingots containing from 0 to 7.5 pct A1 were rolled in air at 850°C to 0.040 in. sheet. Alloys containing from 7.5 to 16 pct A1 could only be rolled about 25 pct reduction at temperatures up to and including 1200°C. Alloys containing above 16 pct A1

Jan 1, 1952

Prospectors were digging silver in the Ray mine area in 1873, and by 1880 high-grade copper ore was feeding a 30-ton copper furnace. In 1910, D. C. Jackling and his associates organized the Ray Consolidated Copper Company, known in mining circles as Ray Con, to exploit the Ray orebody. For 50 years, all mining was underground and the Ray mine was known the world over for innovations in mining methods. It was the first to mine important tonnage (8,000 tpd) by block caving methods. The mill at Hayden, 26 miles (41.6 km) from the mine, kept pace with the new mining methods developed at Ray and in the early 1920's flotation replaced gravity concentration by the vanner machines. First mining by open pit methods began in 1950 and in January 1955 all underground mining was discontinued. The new primary crushing plant, installed in early 1967, featured design simplicity with a low capital cost. The 54 in. gyratory crusher was installed within a total height of 6 1 ft (18.65 m) from the truck dump road bed to the floor beneath the feeder-conveyor under the surge pocket. The crusher is fed by 120-ton trucks dumping from one side only into a 200-ton hopper equipped with a horizontal splitter bar to protect the crusher spider. The crushed ore pocket, of 120 -ton live capacity underneath the crusher, discharges to a 0 to 200 fpm (61.2 mpm), variable-speed, 72 in. by 80 ft long (1.83 m by 24.4 m) sloped belt feeder, probably a first in the industry. Wood-picking stations are provided on either side of the belt so that old mine timbers and tramp iron can be removed from the crushed ore and the wood can be dropped into Dempster containers located below the belt. Counter-weighted finger gates control the bed depth on the belt at 14 in. (356 mm) and a low- level radiation unit automatically maintains a minimum of a 3 ft bed (900 mm) of material on the belt directly under the surge pocket. The conveyor is skirted for its full length and is approximately 60 in. (1.52 m) wide inside its metal skirt liners. Ten impact idlers at 12 in. (305 mm) spacing are provided under the loading pocket and remaining idlers are spaced at 18 in. (457 mm). The belt is 1 ¼ in. (31. 8 mm) thick; and, while it has occasionally been damaged by tramp material, belt life averages 11 million tons. When the belt is changed, the coiled new belt is lowered into position onto one of two belt stands mounted over the feeder, the old belt is cut, and one end is attached temporarily to the new belt. The other end of

Jan 1, 1978

By H. H. Evinger, M. Muskat

Although the shooting of oil wells for the purpose of increasing production has been practiced since 1866, present-day shooting technique has been arrived at almost wholly by a process of trial and error. The difficulties attending either a theoretical analysis of the problem or an experimental attack become apparent when one actually embarks on a theoretical investigation or attempts to formulate an intelligent experimental program. The literature on the subject consists mainly of descriptions of current practice, scattered eye-witness accounts of events following the shooting of a well, and vague speculations on the mechanical processes involved. In contrast to quarry blasting, the results of oil-well shooting cannot be determined by means of visual inspection, and it is perhaps for this reason that only one attempt at what approaches a direct experimental attack has been reported in the literature.' In these experiments, charges of liquid nitroglycerin were exploded in holes drilled in a sandstone outcrop. In order to observe the character and extent of the resulting fractures, the rock was blasted away so as to expose the original shot holes. After all this had been done it was found impossible to distinguish the fracturing due to the original shots from that due to the subsequent blasting. The enlargement of the holes due to the pulverizing action of the shots was measured and an attempt was made to determine the effectiveness if sand tamping. Only five shots were made and few definite conclusions could be drawn. Some small-scale experiments to deter-mine the effect of tamping were performed by Snelling and IIalL2 Small charges (zo grams) of dynamite were detonated at the bottom of a cylindrical hole in a lead block and the resulting enlargement of the hole was taken as a measure of the effectiveness of the explosion. It was found that when the shot was tamped with a sufficient amount of sand or clay, the volume enlargement was approximately double that found when no stemming had been used. The properties of the explosives have been the subject of much study by the manufacturers, the U. S. Bureau of Mines, and various other agencies. For example, velocities of detonation for many commercial explosives are to be found in the Blasters' Handbook, issued by the Du Pont company. Many other properties are given in a treatise on the subject by Naoum.~ The shock wave that accompanies the detonation of high explosives has been studied photographically by Payman4 and others. The hydrodynamical theory of the shock wave has received much attention, and an extended theoretical treatment is given by Bateman.6 Two aspects of the well-shooting problem will be considered in this paper; namely, the fracturing of subsurface strata, and possible damage to casing. With respect to the former of these, several calculations have been made giving the stresses in the rocks surrounding the shot. In order to arrive at numerical results at all, however, it is necessary to introduce a great many simplifying

Jan 1, 1941

By M. Muskat, H. H. Evinger

Although the shooting of oil wells for the purpose of increasing production has been practiced since 1866, present-day shooting technique has been arrived at almost wholly by a process of trial and error. The difficulties attending either a theoretical analysis of the problem or an experimental attack become apparent when one actually embarks on a theoretical investigation or attempts to formulate an intelligent experimental program. The literature on the subject consists mainly of descriptions of current practice, scattered eye-witness accounts of events following the shooting of a well, and vague speculations on the mechanical processes involved. In contrast to quarry blasting, the results of oil-well shooting cannot be determined by means of visual inspection, and it is perhaps for this reason that only one attempt at what approaches a direct experimental attack has been reported in the literature.' In these experiments, charges of liquid nitroglycerin were exploded in holes drilled in a sandstone outcrop. In order to observe the character and extent of the resulting fractures, the rock was blasted away so as to expose the original shot holes. After all this had been done it was found impossible to distinguish the fracturing due to the original shots from that due to the subsequent blasting. The enlargement of the holes due to the pulverizing action of the shots was measured and an attempt was made to determine the effectiveness if sand tamping. Only five shots were made and few definite conclusions could be drawn. Some small-scale experiments to deter-mine the effect of tamping were performed by Snelling and IIalL2 Small charges (zo grams) of dynamite were detonated at the bottom of a cylindrical hole in a lead block and the resulting enlargement of the hole was taken as a measure of the effectiveness of the explosion. It was found that when the shot was tamped with a sufficient amount of sand or clay, the volume enlargement was approximately double that found when no stemming had been used. The properties of the explosives have been the subject of much study by the manufacturers, the U. S. Bureau of Mines, and various other agencies. For example, velocities of detonation for many commercial explosives are to be found in the Blasters' Handbook, issued by the Du Pont company. Many other properties are given in a treatise on the subject by Naoum.~ The shock wave that accompanies the detonation of high explosives has been studied photographically by Payman4 and others. The hydrodynamical theory of the shock wave has received much attention, and an extended theoretical treatment is given by Bateman.6 Two aspects of the well-shooting problem will be considered in this paper; namely, the fracturing of subsurface strata, and possible damage to casing. With respect to the former of these, several calculations have been made giving the stresses in the rocks surrounding the shot. In order to arrive at numerical results at all, however, it is necessary to introduce a great many simplifying

Jan 1, 1941

Jan 1, 1951

By L. B. Herring, Harold Decker

The area under discussion includes districts 2 and 4, so designated by the Texas Railroad Commission,‡ and comprises the following 26 counties: Bee, Brooks, Calhoun, Cameron, De Witt, Duval, Goliad, Gonzales, Hidalgo, Jackson, Jim Hogg, Jim Wells, Karnes, Kenedy, Kleburg, Lavaca, Live Oak, Nueces, Refu-gio, San Patricia, Starr, Victoria, Webb, Willacy, Wilson and Zapata. Drilling and Production The total number of wells drilled in this district during 1944 is shown in Table 5. This indicates a 41 per cent increase in all drilling over 1943. In spite of every handicap created by the war, the oil industry more than met the crisis in its drilling program in this district. Last year we thought it would be impossible to add to the total number of wells drilled in the previous yea;, but in spite of the lack of manpower and materials this large increase was shown. During 1944 this district produced 124,201,978 bbl. of oil from 11,607 producing wells, whereas in 1943 it produced 88,421,693 bbl. from 11,211 producing wells. This is an increase of 35,780,285 bbl. of oil. Some decline has been shown in the older fields arid undoubtedly the majority of wells in the district are producing at too high a rate. However, this district has been able to meet any demands made on it by the Petroleum Administration for War for increased production. Discoveries and Extensions There was a slight decline over the preceding year in the number of wildcats drilled, but the number of discoveries increased. In most instances subsequent development has not been sufficient to arrive at preliminary valuations but it appears that the over-all oil discoveries were below normal and that the gas discovcrics were relatively more important. The Canolis and Tijerina pools, Jim Wells County, and the Dan Sullivan pool, Brooks County, appear to be the outstanding oil discoveries of the year. No important oil reserve was discovered or developed in the Wilcox horizons, although considerable wildcatting was done. Important extensions were made at Agua Dulce and Stratton in Nueces and Teleberg Counties. Production was increased appreciably at Willimar, Willacy County, and Seeligson, Jim Wells County, in sands and areas which were apparently productive at the beginning of the year. Refining Most of the major work in the changing and completing of refineries was finished this past year. Some of the most modern refineries in the industry are now located in the Corpus Christi area. Gas and Condensate No new recycling projects were commenced during the year, nor were there any important additions to the old operations. No major gas reserve was developed, although several new discoveries suggest potentid possibilities.

Jan 1, 1945

By L. T. Leyson, U. C. Tainton

Some time ago, at ameeting of the Institute Prof. J. W. Richards1 said, "I take exception to the statement that all the factors in the production of electrolytic zinc were known long ago.... There is possible in my opinion an improvement of perhaps 50 per cent. in the new electrolytic processes." An examination of the literature of the subject will show the justness of Professor Richards' contention. The work of the earlier investigators was carried on in the shadow of difficulties that, today, are hardly more than memories. We seldom hear now of zinc sponge, that bête noir of the electrolytic-zinc pioneers. Zinc sponge was the name given to a peculiar, soft, black, non-adherent form of zinc deposit that was utterly useless for melting into ingot form. At the big plant at Cockle Creek, New South Wales, in 1897, Edgar Ashcroft2 said that the solution in the plant would suddenly, and without ascertainable cause, go' "bad" and begin to deposit spongy zinc. The most delicate, even spectroscopic, methods of analysis were unable to detect any difference between "good" solution and "bad" solution; either form might change to the other on being kept for a while. When it is added that an outbreak of this insidious disease (which appeared to be infectious, or at least contagious) could be dealt with only by discarding the solution and washing out all tanks and pipe lines, some idea may be gathered of the troubles of the zinc electrometallurgist in what may be spoken of as the "sponge age" of electrolytic zinc. Thanks to the efforts of a number of investigators, we are today able to diagnose with considerable certitude the nature of the malady that puzzled Ashcroft and his co-workers. The researches of Mylius and

Jan 1, 1924

By Walter Renton Ingalls

IN SEVERAL papers and addresses during the past two years, I have dwelled upon some of the economic consequences of the war. The fundamental thought that I have sought to convey is that the world became immensely poorer by the war, not only in material wealth and population, but also in the psychology and morale of the people. I do not see how there can be any intelligent dissent from that statement. All the ideas of post-war prosperity were manifestly fallacious, manifestly fallacious from the outset. If there had been any truth in them it would have followed logically that a great war, with all its destruction of wealth, health and life would be a good thing. Therefore, let us have a great war every ten years or so. Such an idea would be both monstrous and absurd. Assuming then the acceptance of my premise, I have tried to show that the losses by the war could be made good in a short time, i.e., in a relatively short time, only by doing things a great deal better than formerly, and that the accomplishment of such a result called for greater transparency in industry, for industrial cooperation, for thinking in terms of industries as a whole, and for the greater exercise of engineering functions. All of this introduced, of course, the position and psychology of labor. I say frankly that I do not look for labor to contribute any constructive thought to the upbuilding. I neither expect it nor hope for it. This is a pity, for it could do so much for its own economic advancement if it would. However, it never has done so, but rather has benefited only from the exercise of the talents of the few, and the main hope now is to bring it into a passive state, dispelling the resistive fallacies that developed during the war. Let us briefly examine the nature of these.

Jan 1, 1921

By Peter Allen, John R. Stuermer

COUNTRY RISK ANALYSIS A company operating in a foreign country assumes all the risks that it would at home. However, beyond these, it assumes risks that arise from the unique political economic, financial conditions of the foreign country which it operates. These risks are known as "country risks". The importance of these risks has grown appreciably in the recent past (particularly in the aftermath of Iran's revolution in the late 1970s and Mexico's debt rescheduling of 1982-83), and as a result, country risk analysis has become an increasingly useful management tool. Country risk analysis seeks to assess the probability that countries will service their aggregate foreign liabilities on time, as well as the probability that country conditions could inhibit the debt service capability of private sector debtors. This involves assessment of both the ability and the willingness of countries to meet their external liabilities in a timely fashion. "Ability" is linked economic and financial variables: principally, a country's economic structure, foreign exchange generating capacity and debt service burden. On the other hand, "willingness" is tied to political factors: mainly the economic/financial orientation of government policy and the stability of economic decision making. Ability: Economic, Financial Conditions and Prospects Judgement of a country's ability to meet foreign financial obligations begins with a detailed study of a country's external balance sheet which compares the country's foreign liabilities and assets. Table 1 below presents country balance sheets for Mexico, Korea and Indonesia. [TABLE 1 The External Balance 3-,-et 1983 (billions of dollars; Indonesia Mexico Korea Foreign Liabilities 31.1 67.6 40.5 By Source: Bank 13.1 75.5 26.3 Non-bank 18.0 12.114.2 Foreign Reserves 9.3 4.7 7.0] The large magnitude of Mexico's external debt (nearly $90 billion), compared to foreign assets of approximately $5 billion, illustrates the weakness of this country's external payments position, and the main reason that it has been unable to meet interest and principal payments and been forced to reschedule its foreign debt. On the other hand, the relationship between Korea's external liabilities and assets ($50.5 billion and $7 billion, respectively), is more favorable and helps explain why Korea has been able to meet debt service payments and maintain its access to the international capital markets. Indonesia has even a more favorable relationship between its foreign assets and liabilities, $31 billion and $9 billion, respectively, and its debt is mostly lower interest rate, non-bank debt, making for a less onerous debt service burden. After the balance sheet, the analysis turns to a comparison of the country's foreign exchange earning capacity and its prospective financing requirements, that is, the country's future earnings stream

Jan 1, 1985

By Lloyd Emory

THE region known as. Guyana or Guiana stretches along the north coast of South America from the mouth of the Orinoco River in Venezuela to the mouth of the Amazon River in Brazil. Politically, it is divided into British, Dutch, and French Guiana, extend¬ ing into Venezuela on the north and into Brazil on the south. Because the area is within the sweep of the northeast trade winds and of approximately the same latitude, plant' and animal life are fairly uniform throughout. The geology is very similar as far as the northern coast is concerned. The drainage is taken care of by a number of large rivers that flow northward directly into the sea. The Courantyne River, which roughly divides the area into half, is the eastern boundary of British Guiana.1 The lower reaches of this river are also the center axis of an ancient bay that at one time indented the coast-line at this point. The old shore-line and, in fact, successive shore-lines can be traced from near the present coast-line in, the northwest district of British-Guiana, south-east and inland, crossing the Essequibo River near Dahli, the Demerara near Christianburg, the Berbice at the mouth of the Kuruduni River and the Courantyne at Vaka-Kuyaha Falls. The line then swings around to the northeast and again approaches the coast near St. Lau-rent in French Guiana. This article will be confined to British Guiana and largely to the valley of the Demerara River, but for geographic names .and topographic details it might, however, apply to Dutch Guiana as well. British Guiana, which comprises about 90,000 sq. mi. and is as large as England, Scotland, and Wales combined, may be divided into three belts, the alluvial belt or coastal plain, the foot-hill area (often spoken of as the sand clay belt), and the hinterland.

Jan 1, 1928

By R. Stratton-Crawley

Flotation-related processes utilizing an oil phase for processing fine mineral particles have been described and various applications discussed. The problems associated with the techniques are varied, but may be summarized by the following areas; (1) applicability to fine particle beneficiation, e.g. collector extender and emulsion flotation. (2) major 'mechanical' problems, e.g. emulsion breakage and oil recovery in oil flotation. (3) complex interfacial chemistry, e.g. empirical nature of pigment flushing .

Jan 1, 1979

By Jack Parker

The White Pine mine site lies five miles south of Lake Superior in Ontonagon County, Mich. Copper sulfide, mixed with some native copper, is mined by a room-and-pillar system from gently dipping Upper Kewee-nawan sediments. Depth of mining now varies from 700 to 1800 ft and the ore body continues to a depth of at least 3400 ft. An area roughly 21/2 miles square has already been mined. Mining height has varied from 61/2 to 22 ft. A rock mechanics program was set up in late 1963 to promote safety and mining efficiency. This note reports some of the findings. Rock Strength Compressive strength of small, dry specimens of sandstones, siltstones, and shales from the ore zone varies from 20,000 to 30,000 psi. This is intermediate between the softer coal mine sediments and the meta-morphic and igneous rocks of hard rock mines. Annual Cycle of Rock Failure Since 1963, every roof and pillar failure involving more than a few tons of rock has been examined and documented. Some 1500 stations have been installed for measuring convergence, -c1/1000 in., with Invar extensometers. At first it was thought that there was some kind of a cycle of roof failures; perhaps annual, perhaps even elated to the moon or to earth tides, but records (see

Jan 1, 1971

By C. M. Haight

THE mine blacksmith and drill-steel sharpening shop at the Franklin mine of the New Jersey Zinc Co. is on the surface, adjoining the main shaft. It is a brick building, 51 by 30 ft. inside dimensions, with a corrugated iron roof and concrete floor. About two-thirds of the steels used are brought up through the main shaft; the remainder through two auxiliary shafts. The latter are carried to the shop by team or truck. At each shaft sufficiently large stocks of sharp drills of various types are kept to replace all the dull steels that may be sent up; while at the shop enough sharp drills are kept to replace the dull steels in. the stocks kept at the auxiliary shafts. Though this entails keeping a larger number of drill steels in service than might be required by other methods, there is less hurry in the sharpening shop and the steels have a longer period of rest. If a rest from use enables steel to recover from fatigue strains, this method secures that rest. The forms shown in Fig. 1 are supplied to each shift boss in books of 100. These are used to requisition sharp drills from the shaft stocks and enable the men at the tops of the shafts to sort out the required sizes and to have them ready to be sent to the various shaft stations. At one of the auxiliary shafts, the dull drills are placed on a platform from which they are dumped into the body of the wagon that takes them to the shop.

Jan 2, 1926

By C. M. Nickerson

IT is apparent that repressuring of the oil measures is becoming increasingly important to the oil industry, and is a matter that warrants the best efforts of the petroleum engineer charged with applying this method of operation to a producing property. Considerable attention has. been directed to repressuring in various California oil fields, such as Dominguez and Seal Beach, which have served to sell the more progressive operator on this idea and also to keep him sold. The projects that have received most attention are in comparatively young fields where the fluid levels are high, the wells, perhaps, still flowing, where the wet gas production is of considerable volume, and where there is vital need of immediate conservation of gas, which otherwise would be blown to the air. The new State of California Gas Law, which prohibits the waste of gas, has served to interest the oil industry in -means of conserving the gas that is now being blown to the air because of lack of markets. This vitally affects the operator in the older, well-depleted oil fields of the state, because in many cases he has a limited market for gas, on account of the flush production from the more active oil fields. While the waste of gas is relatively small in these older fields, such as the Midway-Sunset area, it now attains considerable importance, since under the new State Gas Law it must be put to some beneficial use. Repressuring in the older fields of California has not received the attention of the petroleum engineers that is warranted by the present situation. This paper was prepared with the view of presenting the salient features connected with repressuring in the well-depleted oil measures of the older fields, and to show what results have already been obtained in these fields by injecting the unmarketable. gas into the sands, particularly in the Midway-Sunset field in the San Joaquin Valley of California. Other projects in the older fields of the state offer some supporting data in this connection, such as the Shields Canyon and the Brea Canyon fields.

Jan 1, 1929

By Walter W. Bradley

Mining by hydraulic process of the important gold-bearing gravels of the Sacramento Valley in the basins of the Yuba, Bear and American rivers began in 1853, and continued at an ever-increasing rate for 30 years. In its most active days it reached an annual production of $15,000,000, and averaged $10,000,000 per year over the 30 years. During that period no provisions were made to prevent the debris from being discharged into the water courses, and ultimately large quantities of silt, sand and gravel were washed down to the lower valleys; filling channels, causing overflow of agricultural lands and difficulty in maintaining navigable depths in the Sacramento River. Agitation and suits filed because of these damages finally resulted in the injunction decision of Judge L. B. Sawyer,' in the U.S. Circuit Court, Jan. 23, 1884, which closed down practically all hydraulic mining operations not having means to restrain their debris. In 1893 (approved March 1, 1893), Congress passed the act introduced by Representative Anthony Caminetti, of California, creating the California Debris Commission, composed of three officers assigned from the Engineer Corps of the U.S. Army, and since that time it has been legal and possible within the drainage systems of Sacramento and San Joaquin rivers to conduct hydraulic mining of gold-bearing gravels behind dams built under this commission's permit and supervision. In the watersheds of the Trinity and Klamath rivers, which flow directly to the Pacific Ocean and do not affect navigation or agriculture, operating permits from the California Debris Commission are not required. There is a measure of restriction there, however, through what is known as the Trinity and Klamath River Fish and Game District. Chap. 215, Stat. 1931, in order to secure relatively clear water for the fishing season, provides that between July 15 and October 15 each year there must not be discharged into these rivers debris that will cause a turbidity greater than a content of 50 parts per million in the

Jan 1, 1937

By J. R. Finlay

The Cæur d'Alene silver-lead mining district of northern Idaho is probably best known to the general public as a seat of labor-troubles. So far as the writer is aware, little has been written and little is known about its geology and resources. People interested in lead-smelting are, of course, cognizant of the economic importance of the region, but they have not communicated much of their knowledge to the public. Exact figures as to the total output of the district are not obtainable, but the following estimates, covering the entire output of the 15 years during which the mines have been operated, are believed to be approximately correct: Group of Mines. Product. Wardner Group, including the Bunker Hill and Sul livan, Empire State-Idaho, Last Chance, Sierra Nevada, bur d'Alene Development Co... . $17,500,000 Cafion Creek Group, including the Gem, Frisco Con solidated, Granite, Standard, Mammoth, Hecla, Tiger-Poorman, Custer and Bell,.... 35,000,000 Mullan Group, including the Morning, You Like and Gold Hunter,........7,500,000 $60,000,000 This output covers the period of discovery and early struggles, and several periods of stagnation caused by strikes and other serious labor-troubles. In 1900 the output of the district was fully $10,000,000, and this figure would have been considerably increased in 1901 had not a curtailment of production been forced by the condition of the lead-market. In 1901 the product was about 150,000 tons of concentrates, with a gross. value of $8,250,000.

Jan 1, 1903

By J. H. Klepinger, C. W. Goodale

I. Introduction....................567 II. Character oF the OrE................568 III. Old FluE System..................572 IV. Tests on Old FLUE System..............575 1. Aspiration Tests................. 575 2. Tests with Steel Settling Chamber........... 575 3. Test with Experimental Brick Flue........... 583 4. Testa on Blast Furnace Geses............. 591 V. Design of New FluE System.............. 597 VI. Main Dust Chamber................. 605 VII. Some DetailS of Construction ............. 609 VIII. THE Chimney.................... 616 IX. Operation of New FluE System............. 624 X. Temperatures and DraFTS............... 630 XI. Velocities and Volumes................ 632 XII. TeStS on the New FluE System............. 637 XIII. Conclusion..................... 643 I. Introduction. In the summer of 1909 the Boston & Montana reduction department of the Anaconda Copper Mining Co. completed a new flue system, at a cost of about $1,100,000, and as this includes the largest and highest chimney in the world, and some new features of flue construction, a description will be of interest. At the Spokane meeting of the Institute in September, 1909, a brief mention was made of this flue system, in discussing Mr. Brunton's presidential paper on the Progress of Metallurgy in the West, and a promise was given that when a long enough time had elapsed, so that operating results could be given, a paper would be offered. The smelting plant includes blast furnaces, MacDougall roasters, gas-fired reverberatories, and converters.

Jan 1, 1914

By F.B. Foley, S.P. Howell

Not infrequently, in the case of the failure of a metal structure, such as a bridge, tank, airplane, gun carriage, etc., a doubt arises whether the failure was due, among other causes, to the effect of an overburden or of an explosive maliciously or accidentally exploded in contact with it. As few means of discriminating between the effects of these causes have been known and these means were of a rough qualitative character, it was surprising to find in the record of an inquiry into the failure of a structure, the statement that, by observations on the Neumann bands in the structure, it was possible to determine the speed of breakage in the metal and to distinguish between a fracture caused by an explosion and one caused by an ordinary mechanical strain. Such a criterion, if well proved, was of value to the explosives experts of the Bureau of Minea, the Ordnance Department of the United States Army and the Bureau of Ordnance of the United States Navy, but search showed no record of it in the literature nor did any of the metallurgists and metallographers consulted know of any data on which such a criterion could be based having been assembled and critically studied. However, it was universally held that there was promise in the idea and that there exkted unique facilities at the Bureau of Mines Experiment Station at Pittsburgh for the preparation, under definitely known conditions, of material for study by metallographers, and that material of value might also be obtained from the proving grounds of the Army and Navy. Therefore, with the approval of the Director of the Bureau of Minea and the Chiefs of Ordnance of the War and Navy Departments, the Chairman of the Division of Engineering of the National Research Council, on April 12, 1919, appointed a Committee on the Investigation of Neumann Bands, which has since been engaged in this study and which, after some slight change in its personnel, consists now of the following: Dr. William Campbell, Advisory Metallurgist, Bureau of Ordnance, Navy Department. P. B. Foley, Metallurgist, Bureau of Mines. S. P. Howell, Explosives Engineer, Bureau of Mines. Comdr. 0. M. Hustvedt, U. S. N., Bureau of Ordnance, Navy Department. Dr. Charles E. Munroe, Chief Explosives Chemist, Bureau of Mines.

Jan 1, 1923