Search Documents

By H. H. Campbell

The following pages discuss some problems connected with the manufacture of steel by the open-hearth process. The methods employed necessarily enter into the domain of what is called theory; but the results are eminently practical. The determination of the various losses of thermal power and the investigation into the chemical reactions in the bath, are important to every manufacturer. It will be understood that definite figures concerning one furnace and one system, will not apply to all other furnaces and systems; but it is hoped that methods are developed, which are capable of general application and which will shorten the labors of others. The gas-calculations contain nothing entirely novel; but certain methods appeared to be very convenient and they are here elaborated in order that others may have a model to follow. The determination of the loss of iron by weighing the slag and finding the percentage of iron therein, is probably unusual. If so, the fact is to be regretted, since this is the only way that an accurate result can be obtained. The common method of estimating the loss in open-hearth work, is to subtract the weight of metallic products from that of the materials charged. Nothing could be more unsatisfactory, inaccurate and meaningless. Pig-iron, steel, wrought-iron and ore are charged into the furnace; complicated chemical reactions occur; the sand of the pig-iron, the slag from the wrought-iron, the gangue of the ore, all rise to the top ; the silicon, manganese and carbon burn and leave the metal; some of the iron oxidizes and goes into the slag; some of the ore is reduced and gives up metallic iron ; the recarbonizer is added, the mission of which is to waste itself; in the pouring of the steel, pit-scrap is made in the ladles, around the moulds and under the spout; the errors in weighing the products join hands to make accuracy impossible; and then the " loss" is determined by diffrence !

Jan 1, 1891

By Z. T. Bieniawski

Tunneling in coal mines includes driving the main haulageways or roadways which serve as the development entries. Although constituting the lifelines of these mines, little attention has been paid to development entries in the United States in terms of systematic pre-construction planning and design. Coal mine tunnels, as the terminology is used in Europe and elsewhere, are understood in the United States to be the main development entries, either in room-and-pillar mining or in longwall mining. These development entries are not tunnels in the traditional sense since they usually are of a multi-entry type involving entries and cross-cuts, and their intersections. Thus, the design of coal mine tunnels is intertwined with the design of coal pillars. This paper summarizes the results of a three-year research project aimed at improving the design of development entries in U.S. coal mining. A design approach has been developed for this purpose and design procedures for roof support in main entries and for pillar sizing are proposed.

Jan 1, 1984

The Library of the above-named Societies is open from 9 A.M. to 9 P.M. on all week-days, except holidays, from September 1 to June 30, and from 9 A.M. to 6 P.M. during July and August. The Library contains about 55,000 volumes, including sets of technical periodicals and the publications of scientific and technical societies. Members of the Institute, with few exceptions, are forced to spend a portion of their time in localities isolated from sources of information. To these the Library can render valuable service through correspondence; letters requesting information will receive special attention. The Library is prepared to furnish references and copies of articles on mining and metallurgical subjects; to determine the existence of mining-maps, and to furnish general information as to the geology and mineral resources of all countries. All communications should be made as definite as possible so that the information received may be what is desired and not include collateral matter which may not be of interest. The time spent in searching for such collateral matter will be saved, and the information will be sent more promptly and in more usable-shape. The members of the Institute can be of service to the Library by forwarding copies of mining-reports, maps privately issued, and similar material, which will be classified, indexed, and made available to other members. Suggestions for additions to the Library, either by purchase or personal solicitation as gifts, will be welcomed. It is hoped that members while in the city will use the Library freely, and assurance is given that most careful service will be rendered to them.

Jan 2, 1914

By M. R. Pickus, I. W. Pickus

Ordinarily age-hardening is thought of as being associated with a limited solubility of one metal in another. Much less has been written about the type of age-hardening that attends the formation of superstructures. Solid solutions generally have a disordered or random arrangement of atoms; that is to say, in a unit cell, such as that of the face-centered cubic lattice, there is no distinction between atomic sites. Atoms of a given metal may occupy cube corners or face centers. Under certain conditions, however, some alloys develop what is known as an ordered structure. In this case, cube corners would be occupied by only one type of atom and face centers by another type. Associated with this ordering process are many interesting changes in physical and electrical properties. Moreover, in many instances the alloys become susceptible to age-hardening. From the evidence now to be described, it appears that age-hardening in 14-carat gold alloys is due to the formation of both a superstructure and a precipitate. Alloys of the metals gold, silver and copper were known in antiquity. The available knowledge regarding their constitution has been ably summarized and extended by Sterner-Rainer,' Jänecke,2 Carter,3 Wise,4 and Coleman.5 Despite the long familiarity with these alloys and the numerous investigations of their properties that have been made, there is still much that remains unexplained. It has been known for a long time that the hardness of these alloys is closely related to the rate of cooling. Similar changes have been observed in the binary gold-copper systemI6 one alloy of which corresponding to the formula CU³AU, has been the subject of a careful and competent report by the English investigators, Sykes and Evans.7 They have established the fact that the shift of atoms from the ordered to the disordered condition takes place in some critical temperature range. At temperatures above the critical range the structure is random, and at temperatures below it the structure is ordered. No difference between these two structures is revealed by the microscope. Both have a face-centered cubic lattice and complete solubility, so that there is no evidence to suggest that the changes in properties are associated with a phase change. The more slowly the alloy is cooled, the higher is the degree to which the ordering process proceeds and the more marked is the increase in hardness. As experimental data were accumulated on I4-carat gold alloys, several contradictions arose. Certain observations tended to confirm the existence of a superstructure, while other observations seemed to be inconsistent with such a transformation. Present Investigation As a focal point about which to develop this subject, it is expedient to consider first

Jan 1, 1943

By M. R. Pickus, I. W. Pickus

Ordinarily age-hardening is thought of as being associated with a limited solubility of one metal in another. Much less has been written about the type of age-hardening that attends the formation of superstructures. Solid solutions generally have a disordered or random arrangement of atoms; that is to say, in a unit cell, such as that of the face-centered cubic lattice, there is no distinction between atomic sites. Atoms of a given metal may occupy cube corners or face centers. Under certain conditions, however, some alloys develop what is known as an ordered structure. In this case, cube corners would be occupied by only one type of atom and face centers by another type. Associated with this ordering process are many interesting changes in physical and electrical properties. Moreover, in many instances the alloys become susceptible to age-hardening. From the evidence now to be described, it appears that age-hardening in 14-carat gold alloys is due to the formation of both a superstructure and a precipitate. Alloys of the metals gold, silver and copper were known in antiquity. The available knowledge regarding their constitution has been ably summarized and extended by Sterner-Rainer,' Jänecke,2 Carter,3 Wise,4 and Coleman.5 Despite the long familiarity with these alloys and the numerous investigations of their properties that have been made, there is still much that remains unexplained. It has been known for a long time that the hardness of these alloys is closely related to the rate of cooling. Similar changes have been observed in the binary gold-copper systemI6 one alloy of which corresponding to the formula CU³AU, has been the subject of a careful and competent report by the English investigators, Sykes and Evans.7 They have established the fact that the shift of atoms from the ordered to the disordered condition takes place in some critical temperature range. At temperatures above the critical range the structure is random, and at temperatures below it the structure is ordered. No difference between these two structures is revealed by the microscope. Both have a face-centered cubic lattice and complete solubility, so that there is no evidence to suggest that the changes in properties are associated with a phase change. The more slowly the alloy is cooled, the higher is the degree to which the ordering process proceeds and the more marked is the increase in hardness. As experimental data were accumulated on I4-carat gold alloys, several contradictions arose. Certain observations tended to confirm the existence of a superstructure, while other observations seemed to be inconsistent with such a transformation. Present Investigation As a focal point about which to develop this subject, it is expedient to consider first

Jan 1, 1943

Allan Gibb, Mount Perry, Queensland, Australia (communication to the Secretary):—In drawing conclusions from his observations, Mr. Van Liew has apparently overlooked the reduction in weight that takes place in the content of the converter. The percentage-compositions of the matte, etc., are not directly comparable for determining the rate of elimination of the impurities; and, in the absence of exact weights (which in such an operation could not be obtained), it is necessary to determine the relation between the impurities and the copper with which they are combined at various stages, in order to get data that are comparable. Owing to a portion of the copper being removed in the slag, etc., the weight of copper in the converter is not a fixed quantity, but.it is sufficiently approximate to permit very reasonable comparison. The analytical data given by Mr. Van Liew, reduced to this basis (a ratio between the impurities and the copper with which they are combined), are shown in the table on page 958. From this table it will be evident that Mr. Van Liea's conclusions as to the source of heat at digerent stages are not quite correct. During the first 10 minutes, no iron is scorified, the heat being derived from the oxidation of the sulphur, of which 7 per cent. of the total is removed in this time. Prom

Jan 1, 1904

By Walter R. Hibbard, George H. Eichelman, William P. Saunders

INTEREST in the various products of the austenite eutectoid transformation in iron-carbon alloys, particularly as produced by the isothermal sub-critical techniques introduced by Davenport and Bain,1 has resulted in the application of similar heat treatments to other eutectoid transformations. Studies2.3.4 of the beta copper-aluminum alloy eutectoid transformation revealed microstructures very similar to those found in iron-carbon alloys. Investigations5,6 of the kappa phase in the copper-silicon alloy system have established the eutectoid type transformation of this phase into terminal alpha and intermediate gamma phases. This transformation has been reported' as forming a eutectoid type structure in a very sluggish manner by a long time isothermal treatment. The purpose of the present investigation is to study the products of the kappa eutectoid transformation as affected by transformation temperatures by means of microscopic and hardness methods. PREPARATION OF ALLOYS The copper-silicon alloy equilibrium diagram is shown in Fig I. The kappa field converges to a minimum silicon solubility at the eutectoid composition and all other completely kappa alloys are hypereutectoid. Thus, kappa decomposition involves first the proeutectoid precipitation of gamma, followed by the eutectoid transformation of a lower silicon content kappa (5.2 pct). Smith5 has indicated that alloys containing between 5.4 and 5.7 pct silicon could be hot rolled, but that the latter composition was desirable in order to permit a wider kappa temperature range. The alloy was prepared by adding Baker's commercially pure silicon to an ingot of copper-silicon alloy containing 2.34 pct silicon remaining from the investigation of Brick, Martin and Angier.7 Following the casting techniques of Krynitsky, Saunders and Stern,8 the ingot was melted under a heavy layer of dried charcoal in a clay-graphite crucible in a gas-fired pot furnace. Small lumps of silicon were held under the melt surface with a graphite rod. After the silicon had dissolved, the alloy was chill-cast and then remelted without a cover, stirred thoroughly, skimmed and poured into a preheated cast iron mold. The cast microstructure is shown in Fig 2. The casting, 10 X 4 X ¾ in., was annealed at 750°C for 21 brand furnace cooled. About 1/16 in. was milled from all surfaces. The plate was cut in half longitudinally and the bottom half analyzed by A.S.T.M. methods.9 The composition by weight was as follows: copper 94.24 pct, silicon 5.56 pct, iron 0.11 pct.

Jan 1, 1948

By C. S. Smith

The solubility of tantalum at 1100°C is 0.025 pct in pure copper, 1.2 pct with 20 pct Ni, and 2.7 pct with -30 pct Ni. The solubility decreases with temperature, and the alloys are precipitation hardenable. A 79/20/1 Cu-Ni-Ta alloy reaches maximum hardness after aging at about 750°C and, if cold worked, does not recrystal-lize below that temperature. The alloys have good tensile properties at moderately elevated temperatures and, since they can be hot and cold worked nearly as easily as cupronickel, they are suggested for service at temperatures above the usual limits for copper alloys. MASSIVE tantalum dissolves extremely slowly in copper-rich alloys, and tantalum powder forms refractory surface layers which prevent its solution unless special precautions are taken. After many trials, an 80 pit recovery was consistently obtained by using a mixture of a finely divided tantalum powder with two or three times its volume of potassium tantalum fluoride (K2TaF1,-melting point about 750°C) poured in a slow stream directly on to the surface of the molten copper alloy, so that each particle would remain coated with flux and be immediately and individually wetted by the molten metal. A 50-50 nickel-tantalum alloy has a melting point of about 1400°C and small lumps of it slowly but satisfactorily dissolve in molten copper-nickel alloys as does commerical "ferro-tantalum." The high affinity of tantalum for carbon makes it necessary to avoid carbonaceous crucibles. COPPER-TANTALUM ALLOYS Castings with good shrinkage resulted when 0.1 pct Ta or more was added to copper melted under charcoal and cast in air. Copper in two-pound melts to which 0.1, 0.15, and 0.2 pct Ta had been added retained residual amounts, by analysis, of 0.025, 0.023 and 0.026 pct, respectively. The solubility of tantalum in molten copper at about 1200 °C is therefore about 0.025 pct. The electrical conductivity of these three samples was 100.48, 100.00 and 100.20 pct IACS in the annealed condition, and 98.24, 97.98 and 98.08 in the cold-drawn condition. Wires 0.080 in. in diam withstood from thirteen to nineteen reversed bends after annealing for 30 min in hydrogen at 850°C and the metal was therefore completely deoxidized. The annealing temperature corresponding to 50 pct loss of work hardness in 1 hr in a strip cold rolled 77 pct reduction was 175C, compared to 230°C for equivalent undeoxidized material. It is unusual for a decrease of recrystallization temperature to result from an alloying addition, and the tantalum probably combines with and removes some minor impurity in the original copper that restrained its recrystalliza- tion. No difficulty whatever was encountered in hot or cold rolling or drawing these ingots, and were tantalum not so expensive it would make an excellent deoxidizer for copper. COPPER-NIcKEL-TANTALUM ALLOYS Studies were made of the solubility of tantalum in a large number of copper-rich alloys, but of these significant solubilities were found only in the case of an iron alloy (which, however, separated into two immiscible liquid layers) and alloys of copper and nickel, in which tantalum is freely soluble and which were found to have interesting properties. The latter alloys are the subject of U. S. Patent No. 2,430,306 (1947). They are not at present available commercially. The Ternary Constitution Diagram—The copper-rich corner of the constitution diagram was constructed on the basis of microscopic examination of samples of various composition and treatments. The alloys were hot rolled to 0.25 in. from castings 0.625 in. thick, then annealed for 1 hr at 1000°C, quenched, cold rolled to 0.10 in. and finally annealed for various periods of time at temperatures between 800" and 1100°C in a nonoxidizing atmosphere and quenched. When the solid-solubility limit had been transgressed, particles of a compound believed to be Ni2Ta*were

Jan 1, 1960

By M. O. Holowaty, C. M. Squarcy

Blast furnaces are the tools of men, and it is men who have made them great. Here is presented the story of the Ironmakers-the men who first poured hot metal into what would someday be the sinews of a nation. W HEN the Jacobean merchant adventurers bade farewell to the first ship of colonists sailing for the new land, they instructed them to direct all their skill and energy to grow silk worms in Virginia. The adventurers felt sure that they could flood the market with highly priced and much desired goods like silk, sugar, tea, and indigo. They were also convinced that they would fill the needs of the mother country for iron. Early iron production in the colonies The merchants certainly had a wonderful imagination, for silk and indigo were just as exotic in Virginia as they were in England. The settlers found it more profitable to raise tobacco on the vast stretches of the free, fertile land. Thus the plans of settlers clashed with those of The Virginia Co.; and only point of agreement was the desire to produce iron. But, even there the motives of the settlers and those of The Virginia Co. of London were worlds apart. The settlers wanted to produce the tools badly needed in the colony, while the Company desired to cash in on the rising demand for iron which the home industry could not satisfy. Both the settlers and the Company lost no time trying to find iron ore. Locations of the early mines are not known. If, however, the reports of the Irishman, Francis Maguel, can be trusted, as early as 1609 a ship sailed for England with a load of 17 tons of crude iron which the East India Co. purchased at £ 4 per ton. The iron was of excellent quality and considered the best iron made of non-English ore that was ever purchased.

Jan 1, 1961

J. H. HEGINBOTHAM, a, metallurgist of the General Engineering Co., talked on "Current Milling Practice at Kirkland Lake," at the December meeting of the Utah Section. The ore is enough alike through the whole district so that some generalizations and comparisons may be made. The question as to whether or not the flotation process should be used in the flowsheet for extracting gold by cyanide solutions is still being vigorously debated, and it will seemingly need some years for a definite answer to be given. Most of the gold is either free, though much of it is finely dispersed in quartz, or occurs with pyrite. At times there may be 2 per cent of telluride compounds in the ore, but the amount of gold telluride present is small and has not been definitely established. It has been shown by Dr. Haultain and others that though gold tellurides may be so finely disseminated that it is necessary to grind the ore exceedingly fine, the compounds themselves are not difficultly soluble. (An increase in temperature helps to dissolve tellurides, and also to settle pulps.) It is likely that if the ore were ground through 400 mesh, practically all of the gold would be soluble. As it is, with 96 to 98 per cent of the ore ground to minus 200 mesh, and some 70 per cent minus 325, the cost of

Jan 1, 1934

By E. H. Timmerman, A. F. van Everdingen, J. J. McMahon

The prevent paper contains a method which combines the material balance equation' with the water influx equation' to obtain reliable values for the active oil originally in place and a quantitative evaluation of the cumulative water influx. The method is illustrated by an application to a reservoir without original gas cap. In the absence of an original gas cap. results may be obtained using only field production and pressure data, PVT analyses. and a minimum of subsurface information. CHARACTERISTICS OF RESERVOIR AND RESERVOIR FLUIDS Production in the field under review is obtained from the top of the Wilcox formation of Eocene age, at a depth of approximately 8,100 ft subsea. The structural map, Fig. 1, shows that the accumulation, half elliptical in shape with the long axis in east-west direction, is trapped to the north and on the upthrown side of a normal fault. A number of east-west faults with additional minor faulting in random directions are found in the general area, and seismic information and production performance indicate in this particular case the existence of a second fault a short distance downdip, with a strike more or less parallel to the fault controlling the accumulation. It is estimated that 1,830 acres were originally underlain by oil and that the maximum thickness of the original oil column, about 37 ft, was only slightly greater than the maximum thickness of the oil-bearing sand. Maximum net sand thickness was estimated at approximately 26 ft. From logging and subsurface information the gross sand volume has been placed at 37.400 acre-ft. which reduces to about 27,500 acre-ft after probable non-productive intervals have been deducted. The following table presents laboratory analyse; data for the Wilcox sand cores. Average Average Samples Considered Permeability Porosity All Samples 236 md ..19.9percent Samples with k>l md 256 md 20.5 per cent Samples with k>8 md 275 md 20.9 per cent Interstitial water was estimated at 15 per cent. The initial gas-oil ratio was approximately 900 cu ft/bbl. and the initial shrinkage factor was determined by the laboratory to

Jan 1, 1953

By S.S. Clarke

The sheet-ground deposits of the Tri-State district, because they are fairly uniform in thickness (7 to II ft.)—rather flat, with an easy dip to the west—and cover a large acreage, offered a problem of improved transportation. Heading advance in this kind of mine is very rapid and track haulage requires a larger crew of trackmen than do other mines, and a heavy investment in track. The use of some type of rubber-tired truck equipment for underground haulage was under consideration for some time by the Eagle-Picher Mining and Smelting Co. The nature of some ore bodies made them not adaptable to truck haulage and some mines that did offer possibilities were equipped with other types of haulage, and the expected savings by the use of trucks did not offset the loss of investment that would be incurred in discarding other equipment. The decision was made to sink a new shaft, designed for skip hoisting, on the Blue Goose ore body, and then develop truck equipment. Developing Tractors and Trailers A study was made of internal-combustion engines for power units in the tractors, but the extreme difficulty of controlling air circulation, and the heavy cost of drilling large churn drill holes for blower installations, led to the adoption of a tractor with a storage battery. The storage-battery tractor that was on the market for mine haulage was impossible to obtain because all were needed for defense work. Several standard electric-truck chassis were purchased and rebuilt in the Eagle-Picher shops. The steering wheel was shortened and set vertical, permitting the driver's seat to be moved forward, and the frame was shortened enough to take the battery box and the fifth wheel support that carried the gooseneck of the dump trailer. The fifth wheel, or turntable, is of the ball and socket type. Tig. I shows the ball fastened to the gooseneck. The socket is split to permit introduction of the ball and is held by through-bolts, and the socket is welded to a ½-in. plate, which in turn is attached to the tractor frame. Smaller wheels and tires were put on to reduce over-all height. If it had been necessary, the spring: could have been reversed, or taken off entirely, to gain additional clearance. The tractors are equipped with 48-cell, 23-plate, 400-A.H. batteries. With the initial tonnage and mileage, the batteries were about 50 per cent down at the end of a shift. Tractors have truck tires 7.50 by 20, 8-ply, front and rear, the rear being dud. After four months of use, the .tires are beginning to show signs of failure.* In

Jan 1, 1943

By S. S. Clarke

The sheet-ground deposits of the Tri-State district, because they are fairly uniform in thickness (7 to II ft.)—rather flat, with an easy dip to the west—and cover a large acreage, offered a problem of improved transportation. Heading advance in this kind of mine is very rapid and track haulage requires a larger crew of trackmen than do other mines, and a heavy investment in track. The use of some type of rubber-tired truck equipment for underground haulage was under consideration for some time by the Eagle-Picher Mining and Smelting Co. The nature of some ore bodies made them not adaptable to truck haulage and some mines that did offer possibilities were equipped with other types of haulage, and the expected savings by the use of trucks did not offset the loss of investment that would be incurred in discarding other equipment. The decision was made to sink a new shaft, designed for skip hoisting, on the Blue Goose ore body, and then develop truck equipment. Developing Tractors and Trailers A study was made of internal-combustion engines for power units in the tractors, but the extreme difficulty of controlling air circulation, and the heavy cost of drilling large churn drill holes for blower installations, led to the adoption of a tractor with a storage battery. The storage-battery tractor that was on the market for mine haulage was impossible to obtain because all were needed for defense work. Several standard electric-truck chassis were purchased and rebuilt in the Eagle-Picher shops. The steering wheel was shortened and set vertical, permitting the driver's seat to be moved forward, and the frame was shortened enough to take the battery box and the fifth wheel support that carried the gooseneck of the dump trailer. The fifth wheel, or turntable, is of the ball and socket type. Tig. I shows the ball fastened to the gooseneck. The socket is split to permit introduction of the ball and is held by through-bolts, and the socket is welded to a ½-in. plate, which in turn is attached to the tractor frame. Smaller wheels and tires were put on to reduce over-all height. If it had been necessary, the spring: could have been reversed, or taken off entirely, to gain additional clearance. The tractors are equipped with 48-cell, 23-plate, 400-A.H. batteries. With the initial tonnage and mileage, the batteries were about 50 per cent down at the end of a shift. Tractors have truck tires 7.50 by 20, 8-ply, front and rear, the rear being dud. After four months of use, the .tires are beginning to show signs of failure.* In

Jan 1, 1943

By P. F. Kinyoun

MANY interesting new features are embodied in the latest extension to the open-hearth department of the Bethlehem Steel Co., at Lackawanna, N. Y. Automatic control of the important factors in furnace operation-fuel, air, draft, pressure, slag composition, and of the temperature in various regions of the furnace-has been carried out to a remarkable degree; the human factor is minimized, and the chances for mishaps and irregularities in operation are greatly reduced.

Jan 1, 1937

By S. Floreen

Seven iron alloys ranging from 5 to 12 pct Ni and 5 to 14 pct Cr were studied. All alloys transformed to bcc massive martensites. Tempering increased the strengths , probably because of relief of residual stresses generated by the martensite transformation. The major strengthening mechanism appeared to be solid-solution hardening by nickel and chromium. Studies of the work-hardening behaviw, of the effects of prior austenite grain size, and of the effects of changing strain rate and test temperature gaue results very similar to iron or low-alloy steels. Increasing nickel contents markedly improved the toughness at subzero temperatures. Studies of the flow properties did not, however, indicate the reason for the beneficial effect of nickel on toughness. The marine atmosphere corrosion resistance of the alloys was improved primarily by chromium additions, but increasing nickel contents were also beneficial at low levels of chromium. J\ number of maraging and PH stainless steels are strengthened by precipitation hardening in a low-carbon Fe-Ni-Cr martensite matrix. To some extent the resultant properties of these steels must depend upon the properties of this matrix. The present study therefore was conducted to evaluate the transformation characteristics and mechanical properties of a series of Fe-Ni-Cr martensitic ternary alloys. A limited evaluation of the corrosion resistance of the alloys in marine atmosphere was also made. ALLOY PREPARATION Seven 100-lb air induction melts were prepared using electrolytic iron, nickel, and chromium metal additions. The initial Fe-Ni charge also contained 0.05 wt pct graphite to produce a carbon boil during melt down. After melting of the base charge, the heats were refined with 0.1 wt pct additions of manganese, silicon, aluminum and titanium and poured into cast-iron molds. The ingots were homogenized at 1250°C and uni-directionally hot-rolled to 2-in. plate. They were then homogenized another hour at 1250°C, and unidirection-ally hot-rolled to %-in. plate at a finishing temperature of approximately 1050°C. The compositions of the heats are given in Table I. Two additional heats were prepared as 40-lb vacuum-induction melts using electrolytic iron, nickel, and chromium metals, and commercially pure molybdenum chips. A carbon boil, and 0.1 wt pct additions of aluminum and titanium were again employed, but manganese and silicon were not added. The heats were converted to %-in. plate using the procedure described above. The compositions of these heats are included in Table I.

Jan 1, 1967

By Gilbert E. Doan

WHEN metallurgists and other engineers meet their college classmates or former teachers, the conversation will frequently become reminiscent and finally turn to engineering education. These graduates have tested the value of their college training in the hurly-burly of the outside world so respectful attention is due their opinions, which, strangely enough, fall into two opposite categories. A member of one group expresses a deep-seated conviction that engineers should have a fuller foundation of physical chemistry, another asks for a more thorough training in mathematics, others wish a more thorough grounding in refractories, a series of courses in petroleum engineering, or in electric welding. Each alumnus of this group

Jan 1, 1937

By C. J. Ramsburg

THE construction and operation of by-product coke-oven plants in America are essential to strong national defense and of the greatest importance to many widely diversified undertakings as well as to safety and health. CARBONIZATION PROCESS Coal used under a boiler or in a locomotive is consumed by combustion. Coal used in a by-product oven is distilled or carbonized, meaning that heat is applied to the coal, out of contact with air, causing a distillation that removes the volatile matter in the coal in the form of gas and vapor, leaving coke as a final product. From the gas and vapor distilled from the coal, many valuable substances can be secured, known as by-products. Hence the name "by-product oven." The simplest example of this principle can be shown by means of an ordinary clay pipe. If powdered coal is placed in the bowl of the pipe, the opening of the bowl is plugged with clay, and the bowl placed in a flame, the bowl will become hot, transferring the heat through the wall of the bowl to the coal within. When this coal attains a temperature of about 950°F., gas will begin to pour out of the pipe stem, and this gas may be lighted. A black liquid also will exude from the stem of the pipe. This is tar mixed with certain other products. What remains in the bowl after distillation is coke. A coke oven corresponds to the bowl of the pipe. A modern oven of the latest type is a refractory brick chamber approximately 42 ft. long and 14 ft. high, averaging 18 in. in width. The oven is filled with coal through closable charging holes in the oven top. Each end of the oven consists entirely of a self-sealing door, the removal of which permits the finished coke to be discharged by means of a power-operated pusher machine. The ovens are built in batteries, and the heating is effected by gas burned in vertical flues in the oven walls, each set of flues heating the walls of two adjacent ovens. Such ovens carbonize a charge of approximately 18 tons of coal in 18 hr., or have a daily throughput of 24 tons per oven, producing about I 7 tons of coke. In times of need, the output may be increased by raising the temperature of flues, thus shortening the coking time. There is one great essential difference in principle between distillation in a clay pipe and in a coke oven. In the 18-in. oven, the distillation proceeds from two parallel walls held at a high temperature (over 2000°F.) and instead of all the coal being heated at once, the distillation is a progressive one creeping inward. The average travel of this heating is 1/2 in. per hour from each vertical wall, and as the volatile products are formed progressively they must push away from the interior toward the wall through the previously formed hot coke, then up the walls and over the top of the coal charge, finally escaping through the outlet pipe. This results in a cracking of the components into many different and valuable substances not formed when the carbonizing temperature is low.

Jan 1, 1942

By M. E. Gershon

A mixed-integer formulation of the mine scheduling problem is discussed and applied for the purpose of optimizing both the mine production sequencing and the mill blending and processing problem simultaneously. Previous attempts at solving these problem separately, although successful, fail to take into account the interrelationships between these problems. Project structure selves as the outline of this paper Generalized in its organization, this concept is useful for long, intermediate, and short range scheduling. Actual applications that show the concept also is applicable to mining a variety of ore are mentioned.

Jan 1, 1984

By Joseph W. Roe

MaNY questions arising in the work of the mining engineer may be solved quickly and with suffcient accuracy by the methods of descriptive geometry; but, unfortunately, this subject is more often considered from a mathematical view-point than as an effective tool for solving practical problems. Some of the principles involved are merged into the ordinary operations of mechanical drawing, and are used unconsciously by the engineer in his every-day work. The rest are stowed away on the book-shelf with his forgotten or rarely-used college text-books. One reason for this condition of " innocuous desuctude " may lie in the uifortunate and often cumbersome notation which it has been found necessary to introduce. If some of these principles can be recalled to the engineer's attenti011 in terms of' every-day use they may prove of practical hearing. Recently, in talking with several mining engineers, I used some of the drawing-room methods of a machine-designer, to the evident surprise of those around me. These men were perfectly familiar with the methods, but their application to mining-work had not occurred to them. At their suggestion the present paper is offered, not in ally way as a treatise, but merely to suggest a certain point of view, in hope that it may lead others far more familiar with mining-problems to pursue the subject further. I. To Find the Strike. As the simplest and most fundamental problem, let it be required to find the strike of a vein when the location and elevation of three points on the outcrop are known. It mill be assumed for the present that the rein is a plane.

Jan 1, 1911

By John E. Lanning

During the last decade, since most smelters have included Cottrell plants as standard equipment for the removal of dust from furnace gases, it has become apparent that smeltermen have had a new problem slowly developing. This problem has manifested itself in accelerated destruction of, or serious injury to, the masonry of flues and chimneys. The masonry either spalls, if the material is of low strength, or acquires large major cracks, either of which conditions attains such proportions that renewals or reinforcing become necessary to maintain the structure in satisfactory condition. This paper describes the failure of a large modern brick chimney to such an extent that its safety was vitally impaired; the investigation of its condition; the methods of restoring satisfactory strength to the structure; and the installation of an acidproof lining. Plant History The Clarkdale smelter of the United Verde Copper Co., which was put in operation in 1915, was primarily a blast-furnace plant. The smelter at Jerome had utilized blast furnaces exclusively, and in the design of the new (1915) plant, blast-furnace smelting evidently was considered of major importance, the smelting equipment consisting of four blast furnaces 48 in. by 26 ft. 8 in. and three reverberatories, each 19 by 101 ft. The latter, supplemented by roasters, were intended mainly for handling dust and fine ore resulting from the crushing operations. The original roasting equipment consisted of six six-hearth Wedge roasters, six more being added in 1917. All gases from blast furnaces, reverberatories, roasters and converters were conducted by means of suitable flues and dust chambers to one central chimney. This chimney, 30 ft. inside diameter by 400 ft. high, is a self-supporting steel structure, lined with 4-in. brick supported on steel shelf angles, riveted to the shell, spaced about 15 ft. vertically. The bricks were of local manufacture, not particularly hard-burned, and were laid in ordinary cement-fireclay-sand mortar. No record is available to indicate that any particular effort was made to secure an acidproof mortar. The same materials were employed in the construction of the reverberatory and roaster flues, and the roaster dust chamber. Parenthetically, it may

Jan 1, 1934