Search Documents

By Nick Barton

A recent analysis of 145 TBM tunnels of more than 1000km total length has helped to quantify the time dependence of utilization (U). In fact U = Tm, where T is time in hours and m is a negative gradient of deceleration. In poor quality ground, gradient m has a strong dependence on rock mass quality Q, for example m ˜ -0.5when Q = 0.1. Good investigation is critical for ensuring faster TBM tunneling then drill-and-blasting, which tends not to slow down (in m/hr) as the tunnel length increases. Anew design model called QTBM allows more reliable prognoses be made, and occasionally will disqualify the TBM solution.

Jan 1, 2001

By J. D. Steenkamp

"In July of 2016 and June 2017, major tap-hole repairs were carried out during the annual shutdown of two 63 MVA submerged arc furnaces producing ferrochromium in South Africa. The hot excavations of the tap-holes allowed for a study of the wear profiles. Subsequent thermodynamic calculations allowed for the quantification of the potential for chemical reaction between refractory and slag or alloy contributing to wear in the tap-hole area. Results from both wear profiling and thermodynamic calculations are reported here. IntroductionFerrochrome (FeCr) is an essential alloy in the production of stainless steel (Gasik, 2013). In 2017, 11.7 Mt of FeCr was produced (Pariser et al., 2018.). The main producers were China (39%), South Africa (29%), Kazakstan (12%), and India (8%).A number of grades of FeCr are available to producers of stainless steel, including high-carbon ferrochrome (HCFeCr) (Gasik, 2013). HCFeCr typically contains 60–70% Cr and 4–6% C (Basson and Daavittila, 2013). When the chromium content is lower (50–55% Cr) and the carbon content higher (6–8% C), it is referred to as charge chrome. Charge chrome is typically produced in South Africa due to the grades of ore available.FeCr is produced in submerged arc furnaces (SAFs) and in open arc furnaces (Mc Dougall, 2013) by carbothermic reduction of oxide raw materials. In a SAF the electrode tips are submerged in a porous charge mix. In FeCr production, the electrical energy is mainly liberated by resistive heating of the wet coke bed (Barker et al., 2007; Steenkamp et al., 2017). Thermally conductive lining design philosophies are typically applied in SAFs producing FeCr (Steenkamp, Denton, and Hayman, 2017; Coetzee, Duncanson, and Sylven, 2010; Coetzee et al., 2010).In July of 2016 and June of 2017, major tap-hole repairs were carried out during the annual shutdown of two 63 MVA SAFs producing FeCr in South Africa. The hot excavations of the tap-holes allowed for a study of the wear profiles. Both SAFs were operated on the same site, by two different operating crews, using the same raw materials. The major difference between them was that the SAF excavated in 2016 was an open SAF (referred to as Furnace A) and the one excavated in 2017 was a closed SAF (referred to as Furnace B). In an open SAF, a gap exists between the top of the steel shell and the roof, with the top of the burden being open to the atmosphere and the CO-rich off-gas being combusted as it escapes. In a closed SAF, the roof is attached to the steel shell and the CO-rich off-gas is collected from an offtake on the roof for further treatment and used in downstream processes.The paper presented here reports the macro-scale observations on refractory wear for the two SAFs, and studies the potential for chemical wear of refractory by slag and alloy as a potential contributing factor to the tap-hole wear observed."

Jun 1, 2019

The effect of rare earth element Y (0-2.0at.%) on the microstructure of TiAl alloys at the as cast and rapidly solidified conditions has been investigated. The results show that the addition of Y greatly refined the microstructure of TiAl alloys at both conditions. The refinement is more significantly with higher Y content. The refinement of Y in the cast alloys is attributed to that the strip-shaped Y-rich phase locating on the grain boundaries impedes the grain growth during solidification. In the rapidly solidified alloys, Y-rich phase dispersing uniformly as spherical particles in the matrix acts as heterogeneous nucleation sites which increases the nucleation rate of ??phase during the ????phase transformation, and produces a refined initial microstructure during solidification. Higher cooling rate restricts the grain growth during subsequent cooling.

Jan 1, 2010

By T. L. Johnston

The Dobbins property about 4-1/2 miles northeast of Cartersville, Ga., was first operated in 1866. It is the oldest manganese mine in Georgia and one of the oldest mines in the United States still producing manganese ore. Changes in ownership lessees and operators and lack of records prevent the compiling of statistics regarding total production of ore from the property

Jan 1, 1942

By Calvin Konya, Anthony Konya

State and Federal construction specifications require the Blasting Contractor to prepare a Master Blasting Plan which is reviewed by the Owner’s Representative. The Master Blasting Plan requires the Contractor to submit the design of a typical blast. Most blasting specifications also require the Blasting Contractor to submit Daily Blasting Plans. The Master Blasting Plan and the Daily Blasting Plan require that the Blasting Contractor also submit the types and quantities of explosives and initiators used. The specifications also request that the Blasting Contractor submit the pounds of explosive used per delay for both production and presplit blasts. The Blasting Contractor may also be required to predict the anticipated ground vibration and air overpressure levels for the proposed blasts. There are equations that can be used to predict the ground vibration. There are also equations that can be used to predict the air overpressure levels. The data for these equations were primarily derived from quarry and surface coal mine and some construction blasts. Data from major construction projects were analyzed in this study to determine new air overpressure propagation equations for construction blasting. These new prediction equations compare calculated results analyzed from field data with other existing air overpressure prediction equations. Production blasting air overpressure values are also compared to air overpressure from presplitting

Jan 1, 2015

By Jack Zhang, Chuck Edwards

"The versatility and specificity of rare earth elements (REEs) have led to their use in an ever increasing variety of applications in new technologies. Consequently, demand for REEs has increased significantly. However, to separate REEs safely and effectively is a complex and expensive process. While China has consistently invested in R&D of REE processing technologies, there have been only sporadic activities in REE mineral processing in North America in the past 20 years. This paper presents a review of REE mineral processing technology, providing an update on current capabilities in REE mineral processing. This paper reviews REE extraction from the major commercially valuable REE-bearing minerals such as bastnaesite, monazite, and xenotime, and also from the ion-absorption type of REE deposits. Currently, there are four major REE mining areas in China, one in the United Sates, and one in Australia. A review of the REE extraction processes in these major REE mining areas closes out the paper.INTRODUCTION The rare earth elements (REEs) include the 15 lanthanide elements, plus yttrium and scandium. The lanthanide elements are normally categorized in two groups: the light rare earth elements (LREEs), i.e. lanthanum through europium (atomic number (Z) = 57 through 63); and the heavy rare earth elements (HREEs), i.e. gadolinium through lutetium (Z = 64 through 71). Yttrium is usually grouped with the HREEs due to similarity in physical and chemical properties. Table 1 lists the REEs, atomic numbers, and abundances in earth’s crust (Taylor and McCleannan, 1985). Promethium is the rarest due to lack of stable isotopes. REEs with low atomic numbers are more abundant than those with high atomic numbers. More interesting is that the REEs with even atomic numbers are much more abundant than adjacent lanthanide elements with odd atomic numbers as shown in Table 1."

Jan 1, 2012

By T. L. Johnston

The Dobbins property, about 4-1/2 miles northeast of Cartersville, Ga., was fist operated in 1866, it is the oldest manganese mine in Georgia and one of the oldest minus in the United States still producing manganese ore. Changes in ownership, lessees, and operators and lack of records prevent the compiling of statistics regarding total production of ore from the property.

Jan 1, 1942

By Richard Pizzi

Built in 1806, Boston's African Meeting House is the oldest surviving Black church building in the country. A $7 million dollar renovation was begun in 2006 to restore this historic building to its 1855 appearance and to modernize the building's accessibility, electrical and mechanical systems. As part of the restoration, an underground utility room and elevator tower, needed to provide handicap access to the Meeting House, were constructed. Extending up to 17 feet below the foundations of the abutting buildings, the utility room was constructed within one foot of some of Boston's oldest and most expensive residences. All equipment and materials had to enter the work area through a narrow alley rendering conventional methods of excavation and construction of earth support using heavy equipment unfeasible. A unique combination of micropiles, structural cap beam, internal struts and shotcrete facing was designed and constructed to provide the permanent and temporary support of the lateral loads from the earth pressures and adjacent building surcharges and the vertical loads from the elevator tower. The narrow and congested streets of the Beacon Hill neighborhood presented many day-to-day challenges for the contractor.

Jan 1, 2011

By K. Aoki, Y. Mito, S. Shirasagi

The authors developed the TBM Excavation Control System (the TBM Navigator), in order to realize the advanced observational construction. During the excavation using this system, the rock strength value is immediately calculated from the TBM driving data as an index of rock properties, and the drill energy coefficient is also calculated from the drill logging data that is carried out using the probe hole ahead of the tunnel face. In this study, a new, geostatistical simulation-based method is proposed for the automatic prediction of the rock properties ahead of the tunnel face with good precision, using both the drill logging data and the TBM driving data. The applicability of this method is validated through the prediction at the actual tunnel excavation that passes through the faults. Les auteurs ont mis au point un Système de Contrôle de forage avec la machine à pleine section (Navigateur de la machine à pleine section), en vue de réaliser un système de surveillance plus efficace. Avec ce système, la résistance de la roche est immédiatement calculée, au cours du forage, à partir des données de conduite de la machine, comme indice des propriétés de la roche, et le coefficient d'énergie de la foreuse est également calculé à partir des données de log de forage collectées dans un trou de sonde foré dans le front de taille. Dans cette étude, on propose une nouvelle méthode basée sur la simulation géostatistique qui permet de prévoir d’une manière automatique, des propriétés de roches se trouvant derrière le front de taille avec une précision satisfaisante, à l’aide des données de log de forage et celles de conduite de la machine à pleine section. Cette méthode s’est avérée suffisamment précise au cours du forage d’un tunnel réel qui traversait une zone de failles. Die Autoren entwickelten das TBM Ausschachtungssteuerungssystem (den TBM Navigator), um noch besser überwachte Bauarbeiten zu ermöglichen. Unter Einsatz dieses Systems wird die Gesteinsfestigkeit während der Ausschachtungsarbeiten unmittelbar aus den TBM Antriebsdaten als ein Index für die Gesteinseigenschaften berechnet. Gleichzeitig wird auch der Bohrenergiekoeffizient aus den Bohrlogdaten berechnet, die an Hand der Probebohrung am Stirnende des Tunnels erhalten wurden. In der vorliegenden Studie wurde ein neuartiges, auf geostatistischen Methoden basierendes Verfahren für die automatische und angemessen genaue Vorhersage der Gesteinseigenschaften am Stirnende des Tunnels vorgeschlagen, für das sowohl die Bohrlogdaten als auch die TBM Antriebsdaten verwendet werden. Die Anwendbarkeit dieser Methode wird durch die Vorhersage bei einer tatsächlichen, durch Verwerfungen verlaufenden Tunnelausschachtung bewiesen.

Jan 1, 2003

By D McClelland, R Whittering

Minerals and Metals Group (MMG) subsidiary Lane Xang Minerals Ltd operates a single site copper and gold mine near Sepon in Lao PDR. Gold production commenced in 2002 and first cathode copper production was in March 2006. Plant throughputs for gold and copper are currently 2.5 Mt/yr and 1.4 Mt/yr respectively; use of a second tailings dam has commenced accordingly. Although the increased catchment area creates opportunities for more storage to reduce demand on other water sources, especially during the dry season, it also creates greater requirements for water treatment capacity.The water balance for mining operations in a tropical monsoon environment with dry winters presents on going management challenges. A successful mining operation depends on a careful balance of water inputs and outputs. The challenge prior to every wet season is having enough storage capacity to absorb potential rainfall. Plant operation in the dry season benefits from water captured and stored from the wet season which reduces the dependence on river water. Release of excess water to the environment is necessary to cope with the overall positive water balance and depends on suitable and effective treatment of water in accordance with the environmental guidelines.Ausenco has recently built and commissioned a second water treatment plant at the Sepon Copper Plant to process tailings decant water.  The objective of the second Sepon water treatment facility is to increase the site water discharge capacity to maintain the water balance and reduce the dependence on river water.  Decant water treatment is required to precipitate the contained heavy metals prior to discharging to surrounding wetlands.  The main metal that needs to be removed from the site water to meet discharge water quality requirements is manganese, as heavy metals are already precipitated to required levels in neutralisation before the tailings are sent to the storage facilities. A site layout provision for removal of manganese to produce a saleable carbonate precipitate is incorporated in the polishing plant design (future installation).

Jan 1, 2009

Detailed mineralogical investigation of a tailing sample from the Juno plant circuit at Tennant Creek was carried out to determine the nature of the unrecovered bismuth and whether any possibility existed for improving bismuth recovery. The investigation showed that the Ibismuth was present in a complex mixture of Bi-Pb-Ou-Se-S minerals (termed "bismuthinite"), of which about 74 per cent was locked (mainly with magnetite) and 26 per cent was liberated (18 per cent in the minus 7 µm slime). The results suggested that attention should be directed to both finer grinding and improved flotation of slime "bismuthinite", and testwork carried out by Peko Mines N.L. on the basis of these recommendations led to a significant improvement in bismuth recovery.Detailed mineralogical investigation of two Juno concentrates was carried out to determine the nature of the selenium present and whether any possibility existed for improving the selenium grade. The investigation indicated that virtqally all the bismuth, selenium, and lead was present in "bismuthinite", which showed a composition range of 32-82 per cent Bi, 0-42 per cent Pb, 0-24 per cent Se, and 5-18 per cent S. Differences in the Bi/Se ratios of the two concentrates could be attributed to different average Bi/Se ratios of the constituent "bismuthinite", and the relatively low selenium grade of the "bismuthinite" precluded the possibility of obtaining a high grade selenium concentrate with high selenium recovery.However, differential flotation and/or low intensity magnetic separation to remove chakopyrite, and magnetite, the main diluents of the concentrate, could be expected to upgrade the selenium content byup to 80 per cent (relative) and .festwork carried out by Peko Mines N.L. on the basis of the recommendations of the mineralogical investigation confirmed that depression of chalcopyrite in the flotation circuit could produce significantly improved selenium grades.These investigations illustrate the application of mineralogy to the practical problems of improving plant performance. Mineralogy has an important role to play in providing quantitative data on which the metallurgist can evaluate plant performance and base a programme of metallurgical testwork, and early mineralogical investigation of feeds, concentrates, middlings, and tailings can lead to the avoidance of much abortive and expensive metallurgical testwork.

Jan 1, 1974

By D P. Sainsbury, B L. Sainsbury, A Vakili, H-D Paetzold, P Lourens

The cave propagation behaviour of a jointed rock mass is strongly governed by the unique nature of joints and discontinuities, together with the intact strength of rock bridges that make up the rock fabric. A discrete finite difference (DFD) modelling technique has been developed to allow for the detailed consideration of the rock mass structural fabric at many scales and through many different stress paths that can be used for complex mine-scale analysis. The DFD methodology uses interfaces to explicitly represent large-scale structures and ubiquitous joints embedded within the simulated rock mass matrix to characterise intermediate structures. Through simulated testing of DFD materials, properties such as strength anisotropy and scale effects can be obtained. This paper discusses the successful application of implementing a DFD modelling technique for the back-analysis of caving-induced subsidence behaviour of Lift 1 at the Palabora mine.CITATION:Sainsbury, D P, Sainsbury, B L, Paetzold, H-D, Lourens, P and Vakili, A, 2016. Caving-induced subsidence behaviour of Lift 1 at the Palabora block cave mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 415–426 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By I. L. Bell

The ironmasters of America had asked the Iron and Steel Institute to visit the USA. The Council decided it was not possible to accept, but Mr. Bell visited; this is an account of his trip. Topics covered include transport, charcoal, coal measures, coal, anthracite, bituminous coal, flux, magnetic iron ore, specular iron ore, limonite, red hematite, clay ironstone, black band ironstone, smelting works, blast furnaces of Pennsylvania, Lake Champlain furnaces, Lake Superior furnaces, Cleveland furnaces, Pittsburg furnaces, Missouri furnaces, and those of the southern states. He goes on to describe Catalan hearths, malleable iron works, Bessemer works, the Blair steel process, and labour.

Jan 12, 1875

By William H. Schiffbauer

The Bureau of Mines has developed a passive encoder for range knobs, a device that automates the task of obtaining the range settings from devices or instruments to be input to microcomputers. It is easily constructed and installed and will not disrupt the device to which it is being attached. It consists of a custom knob and a small printed circuit board that has light-emitting diodes and magnetic reed switches attached. A ribbon cable connects it to a microcomputer. This encoder eliminates one source of human error in an automated process.

Jan 1, 1983

By S. M. Shelton

Ferrograde manganese ore or its equivalent is essential to the manufacture of every ton of steel produced; although it is well-known that there are largo deposits of low-grade ore in the United States, production of substantial amounts of ferrograde material from domestic sources presents a problem that becomes more and more critical as the stock piled ore is depleted through inability to obtain adequate supplies from foreign sources. Consequently, a program of laboratory and pilot-plant investigations designed to solve the problem of obtaining a domestic supply of manganese has been undertaken by the Metallurgical Division, Bureau of Mines. This paper is one of a new series that will include reports of results obtained in the various investigations conducted under the manganese program. The scope of the program and the organization that was set up to direct and supervise the work were discussed in the foreword of the first paper of this series, Report of Investigations 3506, Manganese Investigations 1. Concentration of Manganese Ores from the Drum Mountain District, Utah, by S. R. Zimmerley, J. D. Vincent, and C. H. Schack. Other reports will be published as the work progresses.

Jan 1, 1942

By H. Kotzé

Titania slag is used as feedstock in the production of titanium dioxide pigment. It (titania slag) is the product of ilmenite smelting,a process whereby ilmenite is reduced at high temperature utilizing anthracite as a reducing agent. Although various slag tapping configurations are employed throughout the ilmenite smelting industry, the method of tapping the slag from the furnace into bell shaped cast steel pots, was the subject of investigation in this study. The paper describes the formulation of a cooling model used to calculate and subsequently predict the temperature profile of a slagblock during its cooling within the various cooling environments of pot cooling, air cooling and water cooling. The model was calibrated against actual internal slag temperature measurements and verified with information obtained from both pilot and industrial scale blocks. The paper concludes with solidification results and their practical implication.

Jan 1, 2010

By F. Calizaya

The PT Freeport Indonesia‘s Deep Ore Zone(DOZ) copper deposit is located in the province of Irian-Jaya, Indonesia. Currently, a block cave mine is being developed around this deposit. Production is scheduled to start in year 2000 and to ramp up to25,000 tpd by year 2003. The air quantity requirement for this mine is equal to 780 m3/s. To supply this quantity, the mine will require five centrifugal fans (one 450 and four 750 kW fans). This study summarizes the technical aspects related to the installation and commissioning of one of these fans. The fan was installed on the surface in a parallel arrangement with two others. It has a design capacity of 240 m3/s of air at 2.2 kPa of static pressure. The study presents the installation details from the underground shaft excavation and portal development through fan testing and commissioning. It also presents the results of a monitoring system that was installed to determine the fan duties.

Jan 1, 2000

By V. Riihimäki, M. Luotamo

The Unit of Toxicological Risk Assessment of the Finnish Institute of Occupational Health (FIOH) is conducting a 'Health Risk Assessment for Metallic Chromium and Trivalent Chromium' under the sponsorship of the International Chromium Development Association (ICDA) and the International Stainless Steel Forum (ISSF). This risk assessment will be conducted in accordance with the current European Union legislation in force (Council Regulation 793/93/EEC, Commission Regulation 1488/94/EEC, Dir. 67/548/EEC), but also to meet the regulatory obligations as set out in the European Commission REACH legislation proposal (Consultation Document, the Registration, Evaluation, Authorisation and Restrictions of CHemicals). Further aims include outlining the criteria for the setting of occupational exposure limits for metallic chromium and trivalent chromium compounds. Human Health Risk Assessment according to the current legislation shall entail hazard identification of the toxic end points (acute toxicity, irritation/corrosivity, sensitisation, repeated dose toxicity, mutagenicity, carcinogenicity, reproductive toxicity) including, as appropriate, dose (concentration) - response assessment, and derivation of the N(L)OAELs (No (Lowest) Observed Adverse Effect Level) and/or DNELs (Derived No Effect Level). Exposure assessments for workers, consumers and humans exposed via the environment take into account all the known intended uses. Risk characterisation will compare the typical and/or reasonable worst case exposure estimates to the N(L)OAELs or DNELs to determine Margins of Safety (MOS) for all human populations by each exposure scenario and type of effect, followed by conclusions about the presence or absence of risk. Although all of the key elements of existing legislation remain in REACH, the principal change is that, the burden of proof will be transferred from the member state authorities to industry. The new proposed format of Chemical Safety Report (CSR) will include Risk Management Measures (RMM) as an essential part of the report in addition to the risk assessment. The RMM plays a role in the evaluation of further testing needs and advocating reasons for possible waiwer of requirements. The research programme started in March 2002 and will be completed within the time frame of two years.

Jan 1, 2004

Although the Diamond that is cut and polished and made up into an article of jewellery, is so well known, there are, comparatively speaking, very few outside the industry who know this beautiful crystal in the crude state, as turned out ofNature's laboratory, and the means employed in winning this precious stone.This article is written with the endeavour to give the reader some idea of the geological formations in which the Diamond occurs, and as it is reported that Diamonds have been found in Western Australia, as well as in other parts of the Australian Colonies, a few hints as to the means employed in working the ground in South Africa may be of use to those intending to prqsecute the search in this country. The general geological formation of the South African Diamond Fields is Lacustrine shales and sandstones, intersected by dykes of various eruptive rocks, varying considerably in their character. and in places vesicular in texture, the vesicules being more or less filled in with zeolites by permeating waters.

By C. W. Siyasiya, K. A. Annan, W. E. Stumpf

"SynopsisThe relationship between niobium content and austenite grain growth has been investigated through hot rolling simulation on a Bähr dilatometer. The effect of delay time between passes during rough rolling in Nbmicroalloyed steels with nitrogen contents typical for electric arc furnace (EAF) melting was studied. The results indicate that the grain growth constants n, Q, and A increase with an increase in Nb content. The activation energy for austenite grain growth Q was found to be in the range of 239 to 572 kJ/mol, the exponential constant n ranged from 2.8 to 6.2, and the material and processing condition constant A from 4.24 × 1012 to 4.96 × 1028, for steels with niobium contents ranging from 0.002% Nb to 0.1% Nb. A general constitutive equation for the prediction of austenite grain growth in these Nb-microalloyed steels under rough rolling conditions has been developed. Good agreement between the experimental and the predicted values was achieved with this constitutive equation.IntroductionGrain refinement has been found to increase both the strength and toughness of steels (Gao and Baker, 1998; Sharma, Lakshmanan, and Kirkaldy, 1984; Seok et al., 2014; Maalekian et al., 2012). It is also known that the austenite grain size directly influences the microstructure, and thus the mechanical properties, of the steel (Maalekian et al., 2012; Yue et al., 2010). Effective grain growth control is reported to be achieved through addition of precipitate-forming elements, such as Nb that, slow down the grain boundary migration through pinning and solute drag mechanisms (Yu et al., 2010; Olasolo et al., 2011; Alogab et al., 2007). Much work has been carried out on austenite grain lsize control by the addition of precipitate-forming elements that have a strong affinity for interstitial elements, such as carbon and nitrogen, which form the dispersed pinning particles to inhibit the austenite grain growth (Alogab et al. 2007; Hodgson and Gibbs, 1992; Nanba et al., 2003; Flores and Martinez, 1997; Rollett, Srolovitz and Anderson, 1989). Austenite grain growth can be described using a conventional or a modelling approach. With conventional approaches (e.g. metallography), in-situ monitoring of austenite grain growth at high temperatures is impossible. Modelling the grain growth behaviour based on available data is the ideal option. To quantitatively describe austenite grain growth therefore requires development of a sound mathematical austenite grain growth equation that accounts for the effects of the varying microalloying elements in inhibiting austenite grain growth. Numerous attempts have been made to develop an empirical model based on the general equation developed by Sellars and Whiteman (1979). Many of these models do not account for the direct effects of the microalloying elements such as Nb in austenite grain growth control [Fu et al., 2011; Wang and Wang, 2008; Wang et al., 2006; Shanmugama et al., 2005; Banerjee et al., 2010; Pous-Romeroa et al., 2013). The current work has considered this limitation, taking into account the direct effect of niobium in grain growth control during thermal processing. This is done by incorporating the initial austenite grain size Do and the microalloying element niobium in the development of a constitutive equation for grain growth prediction in Nb-containing microalloyed steels."

Jan 1, 2015