Search Documents

By Cyro Takano

This paper is a contribution to fundamentals data on the equilibrium metal/slag for refining silicon in relation to Ca and Al as impurities. Silicon containing 0.1% Al and no Ca was placed in contact with a slag of various contents of CaO, SiO2 and Al2O3. Slag Al2O3 contents were 11.4%, 25.1% and 29.6%, keeping the ratio %CaO/%SiO2 constant and equal to ~0.53. The experiments were conducted at 1550oC, in a graphite crucible with argon atmosphere. The equilibrium was observed with low and medium content of Al2O3. The derived activities coefficients of Ca and Al in dilute solution of Si presented good correlation with those of the literature. Parallel reactions with formations of SiO(g) and CO (g) were also observed.

Jan 1, 2006

By Pinakin Chaubal

The campaign life of a modern blast furnace depends on hearth wear. Distributions of liquid iron flow and refractory temperatures have a significant influence on hearth wear. A 3-D comprehensive CFD model has been developed specifically for simulating the blast furnace hearth. It includes both the hot metal flow and conjugate heat transfer thorough the refractories. The model has been extensively validated using measurement data from actual blast furnaces. Good agreements between measured and calculated refractory temperature profiles haven been achieved. It has been used to analyze the velocity and temperature distributions and wear patterns at different furnaces and conditions. The results can be used to point out the directions for protecting the hearth.

Jan 1, 2006

By R. N. O'Brien, E. Peters

"It has been discovered that copper concentrates can be leached in strong (40-60%) sulfuric acid with nitric acid, or with oxygen if nitric acid is present as a catalyst. Chalcopyrite is rapidly decomposed at temperatures well below the boiling temperature of the lixiviant (-150 C.) and the resulting copper and ferric salts are precipitated as CuS04.H20 and FeH(S04)z.4H20. Other metal sulfides such as zinc, lead, nickel, etc. are also converted to sulfates that are nearly insoluble. Sulfur is partially converted to elemental and partially to sulfuric acid. Reduction products of nitric acid can be recovered from the distillate with good recovery. Conversion of as-received copper concentrates is largely complete in about 1 hour. Introduction9 molar sulfuric acid is an unusual hydrometallurgical lixiviant: it has a boiling point of about 150 C. and a low solubility for base metal sulfates. Below about 6 molar acid, the boiling point falls below 120 C. and yields much higher sulfate salt solubility, while above 12 or 13 molar acid and at higher temperature sulfuric acid becomes an oxidizing agent, yielding gaseous S02' Thus, sulfuric acid within this range of concentration is capable of acting well above the temperature of boiling water without requiring autoclave conditions, and if typical oxidative leaching conditions are applied to suspended mineral sulfide concentrates, it is possible to obtain a conversion of these sulfides into 'crystalline sulfates. Thereafter, the sulfates can be separated by filtration or by solid - bowl centrifuge and the solution can be recirculated to the reactor vessel. Meanwhile, the solid sulfates can be treated in a typical hydrometallurgical circuit, i.e., dissolved in a return stream that is essentially water, separated from each other by, for example, solvent extraction, and recovered as metals by electrowinning."

Jan 1, 1997

By Roger L. Williams

The Zinc Corporation of America Monaca smelter continues to use the St. Joe-developed electrothermic process for producing zinc metal and zinc oxide. As we enter the 1990s, the electrothermic process flexibility permits treatment of larger quantities? and lower-grade zinc-bearing recycle materials. A new sinter plant having one large sinter machine will increase sinter feed production required to meet our capacity target of 150,000 tons per year.

Jan 1, 1990

By Chia-Fu Chang

We revise the applicability of the theory of self-organized criticality (SOC) to the process of magnetic relaxation in type-II superconductors. It is demonstrated that the driving parameter of self-organization of vortices is the energy barrier for flux creep and not the current density. Power spectrum of the magnetic noise due to vortex avalanches is calculated and is predicted to vary with time during relaxation.

Jan 1, 2006

By Kenneth L. Reid

The Mineral Resources Research Center at the University of Minnesota has recently installed a QEM*SEM system (Quantitative E.valuation of Materials using Scanning Electron Microscopy) to aid in detailed mineralogical evaluation of potential mineral resource developments in Minnesota and to provide services to the North American mineral industry. A primary application for the unit is to serve the Minnesota taconite industry by providing mineralogical analysis of ores and concentrator products. Minnesota taconite ores contain fine-grained magnetite in a quartz matrix. The ores undergo several size-reduction/magnetic-separation steps to produce a final concentrate with approximately 75% passing 325 mesh and containing about 5% gangue. The paper describes a typical taconite concentrator flowsheet and reports some preliminary results of the applications of QEM*SEM particle image maps and cumulative yield liberation data to samples from selected points in the concentrator circuit.

Jan 1, 1988

By Raj P. Singh

Two design-of-experiments studies were carried out to investigate the leaching of technical grade molybdenum tri-oxide (TGM) in the presence of hydrochloric acid and the mother liquor of ammonium di-molybdate crystallization used as an ammonia source. Results indicated that leaching of TGM in HCl is possible only when used at about 1N concentration. In high concentrations of HCl, technical grade MoO3 had very high solubility (7.5 to 40 g/L Mo). The most suitable conditions for HCl leaching of TGM were obtained at a slightly elevated temperature of 80°C. Using about 1N HCl at 80°C, potassium in the leached solids (TGM) decreased to about 110 ppm, a value typically obtained in TGM leached in HNO3 - NH4NO3media (3.5 - 4.0 moles /L HNO3 + 0.5 ? 1.0 moles/L NH4NO3). Mo losses under these conditions were 0.8-0.9 g/L Mo. The HCl-leach method, presented here-in, has a significant advantage in chemical cost and environmental benefits over HNO3 ? NH4NO3 purification method.

Jan 1, 2006

By F. Leclerc, V. Rebeyrolle, M. Revil-Baudard, A. Jardy, M. Založnik, H. Combeau

"Since the quality of Vacuum Arc Remelted ingots is linked to their chemical homogeneity and metallurgical structure, a modeling study of the solidification during VAR has been undertaken. It is based on the solution of the coupled transient heat, momentum and solute transport equations during the remelting of a cylindrical ingot. Solidification mechanisms implemented in the model include a full coupling between energy and solute transport in the mushy zone, and accounting for nucleation and finite diffusion of solutes at the microscopic scale, in both solid and liquid phases. This modeling can be applied to actual multi-component alloys. In this paper, the macrosegregation in Zircaloy 4 ingots is investigated. To validate the model, one single melt of a homogeneous electrode has been specifically performed. The comparison between the predicted macrosegregation and the experimental results shows the importance of accounting for solutal convection to forecast properly the macrosegregation in remelted ingots.IntroductionVacuum Arc Remelting of zirconium alloy ingots is a key step in the manufacturing process of fuel assembly components in nuclear reactors. The control of the chemical homogeneity is indeed fundamental to ensure the quality and the in-reactor performance of the final products. Despite the use of electromagnetic stirring to homogenize the liquid melt composition, chemical heterogeneities develop in the mushy zone during the solidification stage. One of the main challenges for zirconium producers, as well as titanium producers, is to master the VAR process in order to control the macrosegregation in remelted ingots. Macrosegregation results from the association of microsegregation and transport phenomena. The latter are primarily due to the flow in the liquid and mushy parts. It is now well established [1-4] that the hydrodynamics of the melt pool in a VAR ingot depends on the combined action of the followings: thermal and solutal buoyancy, self-induced electromagnetic force and the periodic centrifugal force caused by the angular movement generated by the stirring. However, for zirconium alloy ingots, the effects of thermal and solutal buoyancy forces on macrosegregation through their influence on the flow in the mushy zone have not been clearly identified."

Jan 1, 2012

By W. Gong

Their outstanding thermal stability and high energy product make Sm(Co,Fe,Cu,Zr),-type alloys attractive for advanced applications. The near net-shape production of Sm(Co,Fe,Cu,Zr), bonded magnets make them potentially superior to any magnets made by sintering. Although pioneering work done by Shimoda et al. and other investigators provide insights on the proper compositions and process control of this alloy system, additional work is still necessary to improve our understanding of alloy behavior at various processing stages and to increase the production yield during powder processing. In this paper we report on the development of anisotropic Sm(Co,Fe,Cu,Zr), alloy powders for the bonded magnet application. Our focus is on the development of a moderate coercivity powder requiring a relatively low magnetizing field to charge the magnets to their optimum Br, Hci and BHmax. The magnetic properties are related to the evolution of the microstructure at various processing stages and the average particle size and size distribution of powders.

Jan 1, 1997

By David Goodman

The typical operating conditions in Solvent Extraction plants are presented. The various materials of construction used for solvent extraction equipment are reviewed and the history of their use presented. The properties of the materials in common use today, stainless steel, thermoplastics and fiber reinforced plastics, are compared together with cost data. The manufacturing and construction aspects of these materials are discussed.

Jan 1, 2003

By Cashman R. S. Mason

Removal of halides (fluoride, chloride) from metallurgical solutions can reduce corrosion rates and improve hygiene from decreased anodic chlorine evolution. This is particularly true for zinc sulphate electrowinning solutions. This paper describes the chemistry of a new process for the removal of halides from such solutions by solvent extraction ? the Teck Cominco Halogon? process, for which patents are pending. In this process, the halides are loaded directly from commercial zinc sulphate solutions and are stripped into a form suitable for disposal. Sulphate extraction efficiency is variable while maintaining halide extraction efficiency. The method of optimizing the solvent composition is demonstrated.

Jan 1, 2003

By Vladimir Lobanov, Vladimir Skorohodov, Boris Radionov, Olga Makovskaya

"The synthetic sorbents and the activated carbons which are used for the metals extraction from weak process liquors are rather expensive. It is propose to use mineral and synthetic high-porous substances which sharply increased sorption properties by special processing. For achievement the desirable properties sorbents are impregnated by specially prepared solutions. Such solutions should contain the substances or its anionic forms which on the one hand are strong enough fixed in a supporter pores, with another are capable to form the insoluble compounds with extracting metals. Selectivity is provided by chemism of the reagent interactions with extracting metal. Due to the high concentration of a reacting ion in a sorbent phase the capacity and rate of sorption increases. Formed insoluble compound remains in a phase of the sorbent and necessity of its filtration disappears. For synthesis the sulfhydryl compounds which chemical properties allow to increase degree of extraction and capacity of the activated carbon were used. At hydrometallurgical processing of precious metals mineral raw materials the commercial solutions with the concentration of gold from 0,1 to 5 mg/dm3 are received. Commonly gold is precipitated from cyanic solutions by the zinc dust. The sorption methods are widely applicable. But the synthetic sorbents and the activated carbon using to these purposes are rather expensive. Expenses for sorbents even at its regeneration can reach 10-15 % from total expenses of gold extraction from ores. When sorbent regeneration, mostly for carbon, is not provided, this share increases to 30-40 %. Thereupon search of the sorbents combining availability, the sufficient capacity, demanded degree of extraction and the low price is actual. For the specified purpose it is offered to use the mineral and synthetic high-porous materials which sorption properties are sharply rose by special treatment. Among such substances are natural zeolites, silica gel, lignine et al. Similar treatment can improve the sorption properties of sorbents used in practice, particularly, the activated carbons. The simplest treatment of potential sorbents consists in its impregnation by specially prepared solutions. Such solutions should contain substances or its anionic forms - impregnating agents. These agents should be on the one hand strong enough fixed in a carrier pores, on the other hand are capable to form with extracting metals insoluble compounds. The more strong compounds are formed the high degree of metals extraction from solutions. The sorbents with similarly changed properties are named the impregnated sorbents."

Jan 1, 2008

By K. Sadrnezhaad

Industrial and experimental induction furnaces are used for melting various types of iron ingots, returned scraps and DRI sponge pellets to produce high purity cast-iron and steel heats. The lowest consumption of the electrical energy is determined for continuous feeding operation to be 0.3 KWH/Kg for production of cast-iron in 1.5-ton industrial furnace and 0.45 KWH/Kg for production of steel in 25-Kg experimental furnace. The optimum feeding rate for lowest energy consumption is obtained to be 12.5 grams per second for continuous feeding of DRI in 25-Kg induction furnace. Similar measurements show that the optimum size of the DRI pellets is around 8 millimeter.

Jan 1, 1988

By M. R. Dahm

The demand for low sulfur steel by steel manufacturers and their customers has been steadily increasing for 25 years. Historically sulfur has been controlled by various means and with various additives but lime-magnesium external desulfurization of hot metal has become established as the dominant method in North America today. Magnesium powder produced from primary magnesium ingot has been the major source or raw material. However, periodic increases in the price of this commodity have encouraged producers to look to secondary magnesium for an alternate source of magnesium. Secondary magnesium from post-consumer scrap can be cleaned, sized, and prepared to produce a high quality magnesium reagent for use in hot metal desulfurization at a lower cost than material processed from primary ingot.

Jan 1, 2000

The resist profile simulation is carried out using the combined data obtained. The nematic liquid crystal is clear only when a long range order exists, in the whole medium. using the Jones matrix method. Director can change from point to point and is, in general, a function of space. Details of the lens structure and of the devices fabrication and performance are described. Light from conventional light source or laser is passed through a polarizer and then incident on the specimen At the nematicisotropic, transition temperature, the medium becomes isotropic and looks clear and transparent. The transition can be approached by changing the impurity concentration or, indirectly, by tuning the temperature since the pinning strengths of the random and crystal potential have in general a different temperature dependence.

Jan 1, 2006

By D. Maurice, W. D. Riley, J. A. Hawk

"The increased penetration of wrought aluminum into the automotive market is stimulating a need to separate wrought aluminum from cast aluminum because of: a) the additional value of scrap wrought alloys and b) the increase in the total amount of aluminum automotive scrap will outstrip the demands of secondary aluminum foundry industry. The availability of clean fractions of wrought and cast aluminum and incidentally, a clean cast magnesium fraction will allow increased recycling of aluminum used in the automotive industry.Hot crushing has been tested previously and proposed as a means to separate cast from wrought alunrinum product. The underlying concept is that when a mixture of cast and wrought aluminum is thermally processed and then subjected to crushing action, differences in toughness between wrought and cast aluminum alloys will become more pronounced. Hence, it should be possible for conditions can be established such that the cast material fragments, while the wrought material, having lost much less of its toughness, merely deforms. The two types of product could then be separated by simple sizing methods.In this paper we report on the testing of this concept. We were unable to replicate the results which originally demonstrated proof of concept. Possible reasons for this are discussed, as well as the possibility that the original results may not be as desirable as the current results for subsequent sorting."

Jan 1, 2000

Due to problems with old technologies more and more product designers have turned to liquid crystal (LC) displays, which have consequently experienced phenomenal growth. The success of liquid crystal displays has fostered continued development, to the point where full-color video displays have been realized which can rival. The details of the lens structure and of the devices fabrication and performance are described using the Jones matrix method. Director n can change from point to point and is, in general, a function of space.. The transition can be approached by changing the impurity concentration or, indirectly, by tuning the temperature since the pinning strengths of the random and crystal potential have in general a different temperature dependence. Light from the conventional light source or laser is passed through a polarizer and then incident on the specimen. The resist profile simulation is carried out using the combined data thus obtained. The nematic liquid crystal is clear only when a long range order exists, in the whole medium. At the nematic-isotropic, transition temperature, the medium becomes isotropic and looks clear and transparent.

Jan 1, 2006

By Dieter Offenthaler

Catalysts used in petroleum industry often contain valuable amounts of PGMs. The typical recycling route for those materials is the pyrometallurgical one, but this treatment way offers limited flexibility with respect to small charge weights. A new process, combining a pyrometallurgical pre-treatment step of the ceramic carriers with a hydrometallurgical leaching procedure overcomes this disadvantage. It not only allows the economical treatment of even very small charge weights, but also gives the possibility to maximize the PGM yield by individually adapting the process to the different charge materials. Due to an ingenious process design, where all leaching agents and effluents are recycled in a closed loop and therefore no waste waters leave the process, process operation becomes very economical. However, the temperature-time-regime in the pyrometallurgical pre-treatment step is of major importance for the success of the whole process. Therefore various investigations have been done to identify how the different process variables in the pyrometallurgical pre-treatment influence the subsequent leaching procedure. It turned out, that the adjustment of the correct phase-modification in the ceramic carrier materials during the pyrometallurgical treatment is the key factor of this process step. Although it is a troublesome issue to exactly adjust the correct phase modifications, it is the prerequisite to take advantage of the benefits of this new process concept.

Jan 1, 2006

By Qin Li

An highly active absorbent with oxidization based on fly ash, lime and additives was prepared. Experiments of simultaneous desulphurization and denitrification were carried out using fixture bed and duct injection. The influential factors for the absorptive capacity of the absorbent were studied. The absorptive capacities of 120.7mg for SO2 and 43.7 mg for NOx were achieved at a Ca/(S + N) molar ratio 1.2, respectively, corresponding removal efficiencies of 87% and 76%, while spent absorbent appeared in the form of dry powder. The optimal temperature and humidity of flue gas treated with this process were shown to be approximately 50\\176 and 5% respectively. The mechanism of removal for SO2 and NOx was investigated. In comparison with traditional dry FGD, this process appears to have lower cost, less complicated configuration and simpler disposal of used absorbent. The valuable references can be provided for industrial application by this process. The foreground of application will be vast in China and in the world.

Jan 1, 2006

By Fuqiang Zheng, Feng Chen, Wenting Duan, Yufeng Guo, Tao Jiang

High-quality titanium-rich material is of significance in the development of titanium industry as it is the main raw material to produce sponge titanium and titanium white using chloride process. Activation roasting of titanium slag with high Ca and Mg contents as adding H3PO4 followed by acid leaching was investigated to prepare titanium-rich material. The effects of H3PO4 dosage, roasting temperature and time, hydrochloric acid quantity, acid leaching temperature and time on TiO2 grade and removal of impurities were studied. The results show that after the finely ground titanium slag roasted with 8% H3PO4 at 1000 for 2h, most Mg impurities in anosovite solid solution structure were converted into simple acid–soluble compounds. The impurities such as Ca and Mg obviously decreased when the hydrochloric acid concentration was 20%, leaching at 100 °C for 2h, from which a titanium-rich material containing 82.56% TiO2 and 1.15% (CaO+MgO) was obtained.

Jan 1, 2016