Search Documents

By Ali Naeimipour

Availability of accurate geological information about the rock mass surrounding a tunnel or mine working is the key to enhance and optimize the required ground support measures. Various approaches have been used to obtain data on ground conditions, including the possibility of characterizing the ground while drilling for roof bolts, by the Measurement While Drilling (MWD) system, via optical, sonic and acoustic televiewers, and using various types of gamma probes. While there are many different systems for characterizing the ground in longer, larger-diameter holes drilled downward, the options for using probes and logging systems in short, small-diameter holes drilled in horizontal or an upward direction are very limited. This paper will present the results of recent field tests using optical televiewer (OPTV) to analyze the joints and voids in boreholes drilled in different directions. The studies show that OPTV is a promising tool; however, getting a good quality image from the upward drill holes still need to be studied. Meanwhile, estimated in-situ strength of the intact rock is needed to complement the jointing pattern for rock mass classification. For this purpose, preliminary steps for the development of a borehole scratcher to estimate rock strength will be discussed in this paper.

Jan 1, 2014

By Christopher J. Brown

"Proper ground stability in gate roads has been a critical aspect of success in longwall mining. In particular, the tailgate has proven to be one of the more active mine areas that needs to be managed (Barczak, Dolinar, and Mucho, 1999). As longwall tailgate support technologies continue to be developed and improved, Strata Worldwide has worked to design and manufacture a revised Propsetter to provide additional support capacity and enable applications at greater mine heights. The support is targeted for tailgate applications; however, it can also be used for roof support in various types of mining environments. This paper describes the design changes for enhancing the support capacity of the Propsetter to more closely align its performance with other support technologies currently being employed in longwall tailgates. Balancing changes to each design aspect of the Propsetter was key to successfully improving the roof support load capacity while maintaining controlled deformation. Increasing the load capacity would allow a mine to improve support efficiency with a smaller, less intrusive support compared to support alternatives and to reduce the cost per foot of supported entry. The target support capacity was 80 to 100 tons at two inches of deformation to more closely match the performance of competing tailgate supports, such as the 24-inch-diameter CAN®. To achieve this goal, changes were made to all design aspects of the Propsetter: diameter, wedge cut depth and angle, pod size, and confinement rings. Test results from the NIOSH Mine Roof Simulator verified that these design changes were successful in increasing the capacity of the Propsetter to the 80- to 100-ton range at two inches of deformation. INTRODUCTION Roof support is one of the most fundamental elements of the underground mining process. As materials are removed from the earth, geological conditions will almost always require some form of roof support to keep the extraction area open and stable. Coal mining environments often experience difficult geological conditions that require both primary and secondary forms of roof support to keep the mining environment safe and economical. The secondary support system serves as additional support in the case the primary support system is inadequate. If designed properly, the secondary support system will also assist in maintaining integrity of the immediate roof beam (Barczak, 2000)."

Jan 1, 2017

By Arka Jyoti Das, Prabhat Kumar Mandal

"Coal mining in India has a strategic importance for the energy security of the country. Presently, the majority of coal production is coming from open-cast mining. Due to the fast depletion of reserves amenable to open-cast mining, future coal production will depend primarily on underground production. In conventional bard-and-pillar/room and pillar mining as it is practiced in India, the percentage of extraction is very low. In fact, within most Indian coalfields, a large number of coal seams extract only 15- 20% of coal, but no pillar extraction is done due to the presence of surface or sub-surface structures leading to huge amount of coal being locked-up in underground. Spontaneous heating and fire, the accumulation of poisonous gases, severe stability issues, unsafe workings and environmental hazards are all major problems associated with these developed coal pillars, so there is a pressing need for technology in the mining industry to extract this huge amount of coal locked up under different constraints. In this study, we propose that the locked-up coal be extracted by replacing the developed coal pillars with artificial pillars. The paper briefly discusses the extraction methodology designed for this and its evaluation through numerical modeling for applied suitability underground.INTRODUCTIONDriven by rising populations and urbanization, an expanding economy and also a quest for improved quality of life, energy usage in India is expected to increase manifold in the coming years. As for India's energy scenario and its projected future plans, there is no doubt that coal will remain a prime source of energy, even over the next few decades.The majority of coal production in India comes from open-cast mining because of large-scale mechanization, but the coal reserves amenable to open-cast mining are gradually depleting - which may impose adverse impacts on the energy sector if underground production does not increase. Underground coal extraction, meanwhile, is going to become more complicated in near future due to the fast exhaustion of easily mineable coal reserves."

Jan 1, 2016

By Muhammad Zaka Emad, Rangzeb Goraya, Muhammad Usman Khan

"Numerical modeling has been used extensively to assess the stability of surface and underground mines. Tabular, steeply dipping ore bodies are generally mined out by open stoping methods with delayed backfill. Cemented rockfill (CRF) is employed as a backfill material for narrow vein deposits with low production rates. Sublevel stoping methods with delayed backfill are employed to mine out steeply dipping ore bodies. Backfill is exposed to blast-induced vibrations and dynamic loading due to loss of confinement, which could lead to backfill failures. Backfill failures could influence the operating cost of a mining stope and the productivity of the entire mining project. This work shows a detailed overview of the factors contributing to backfill failure. A detailed literature review is presented along with case studies of longhole stoping operations from the Canadian Shield region for this work. The backfilled stopes are analyzed with the finite difference code FLAC3D. The literature review shows that the factors primarily responsible for fill failure are the strength of backfill, stope geometry, mining sequence, and blast-induced vibrations. INTRODUCTION Sublevel stoping methods with delayed backfill are popular in Canadian hardrock and metal mines. Backfill facilitates ground control and greater recovery of ore with pillar mining. It reduces wall slough, thus decreasing ore dilution from adjacent walls. The production of cemented rockfill (CRF) is simple; rock aggregates are mixed together with cement slurry and then placed in a mined-out stope. CRF has a low water content, thus it requires no additional drainage unlike some other backfill. Low water-to-cement ratio enables faster curing rate, hence a faster mining cycle can be achieved (Annor, 1999; Hassani and Archibald, 1998; McKay and Duke, 1989). CRF is generally placed in stopes from the upper sill drift using a truck or a load haul dump machine. Some of the problems associated with CRF are the moderate to high operational cost, the difficulty to get a tight filling, and segregation. Backfill failure is a product of many factors, such as cementation, particle size distribution, placement method employed, water quality, segregation, and blast-induced vibrations. The problem of segregation in aggregates has been observed when aggregate is dumped from a backfill raise (Meech, 2012; Indiana DOT, 2013). Segregation becomes unavoidable when the aggregates are not properly sized (Yu and Counter, 1983; Stone, 2007; Yu, 1989). The exposed backfill zones will contribute to ore dilution due to backfill when subjected to dynamic loading due to fill failures. This paper presents a detailed literature review and numerical modeling results of a mine backfill, along with case studies from longhole stoping operations. The backfilled stopes are analyzed with the finite difference code FLAC3D (Itasca, 2017). The literature review shows that the primary factors responsible for fill failure are the strength of backfill, geometry of stope, sequence of mining, and the vibrations induced by blasting operations."

Jan 1, 2017

By Ihsan B. Tulu, Keith A. Heasley, Aanand Nandula

"The objective of this paper is to present the development of a software tool that will assist in an area calculation of the Analysis of Roof Bolting Systems (ARBS) support intensity while incorporating more detailed geology, stress, and intersection span input. In this area ARBS tool, a detailed CMRR distribution can be determined from the available geologic database at the mine. In addition, the overburden and multiple-seam stresses, as obtained from the boundary-element program LaModel, can be converted to a “pseudo-depth” which is then used as the depth input to the area ARBS calculation. Finally, the section-specific intersection spans can be determined from the mine design for input to the calculation. All this detailed area input information for ARBS is handled by the latest version of the Stability Mapping (StabMap) program, which now outputs an area ARBS suggested support density given the required input parameters. This final ARBS grid can be plotted, analyzed and overlaid on the mine map for optimum use in support design and for presentation to production personnel.INTRODUCTIONSince the inception of roof bolts in the 1940s, there has been a lack of a universally accepted roof bolting design method (Mark, 2002; Mark and Pappas, 2012). To address this situation, the National Institute of Occupational Safety and Hazard (NIOSH) developed roof support design guidelines, which were incorporated into a computer program called the Analysis of Roof Bolting Systems (ARBS). These guidelines were based on the effects of roof quality, stress, and mine geometry (Mark, Molinda and Dolinar, 2001). The roof rock quality in ARBS is represented by the Coal Mine Roof Rating (CMRR), the depth is used as a surrogate for the stress, and the intersection span serves to represent the mine geometry (Mark, Molinda and Dolinar, 2001). These three input parameters are used in the fundamental, empirically derived equation of ARBS to calculate a required support density factor, called ARBS, (Mark, Molinda and Dolinar, 2001):"

Jan 1, 2018

By Essie Esterhuizen, Michael M. Murphy, Chris Mark

"The response of the surrounding rock mass to the creation of mining excavations determines the ultimate load on a pillar support system. In conditions where the ground is relatively soft and weak, the full overburden weight can be transferred to the pillar system. However, in stiffer and stronger rocks, a greater portion of the overburden load is transferred to the unmined coal barriers or abutments, and the pillar stress is reduced. This paper makes use of numerical models to examine the interaction between typical pillar systems and the surrounding rock mass for weak and strong geological conditions at various spans and depths of cover. The concepts of structural failure and functional failure of pillars are used to assess pillar performance when pillars are deformed beyond their peak resistance. The results show that the span-to-depth ratio is an important factor in determining the pillar stress and the ultimate deformation of pillars. The ultimate pillar strain appears to be closely related to the functional success of pillar systems.INTRODUCTIONThe National Institute for Occupational Safety and Health (NIOSH) was requested by Congress to study the safety of retreat pillar mining following the Crandall Canyon Mine disaster that took place near Price, Utah in August, 2007. As a part of this study, an investigation was made to better understand how the rock mass responds to the creation of mining excavations and how the loads are distributed among the pillars and the surrounding abutments or barriers. The outcome of these investigations contributed to the development of a modified loading model for the ARMPS-2010 (Mark, 2010) method ofretreat mining pillar design.Structural and Functional Failure of PillarsPillar design is typically conducted by estimating the pillar strength and stress, and then sizing the pillars so that an adequate margin of safety exists between the expected strength and stress. The pillar strength can be defined as the maximum resistance of a pillar to axial compression (Brady and Brown, 1985). If a pillar is loaded beyond its peak strength, load shedding or yielding can occur, and the pillar is considered to have failed as a structure. Structural failure generally refers to a loss of loadcarrying capacity."

Jan 1, 2010

By Andrzej Walentek

In polish coal mining due to specificity of seams lying the multiple extraction is used. In this kind of mining, it is essential to take into account all geological and mining conditions which have an influence on stability and functionality of workings during their using. In view of above, for one of polish coalmines, by mean of Phase2 program, the numerical calculation were made for assessment of the influence of advancing excavation front on convergence of roadway located 30 meters above longwall was analysed. In order to verify developed prognosis, in analyzed roadway the underground investigations in scope of convergence measurement and changes of load exerted on working support were carried. As a result of these investigations it was found that real convergence on certain part of roadway was significantly larger then determined in prognosis. Additional calculations and analysis showed that the main cause of differences was underestimation of influence of dynamic load, which was an effect of numerous low energetic rockmass tremors. These tremors, related to excavated longwall, were located in close proximity of roadway in its part where the biggest convergence occurred. In current practice, in this type of convergence prognosis, the maximal value of dynamic load exerted on roadway resulted from single rockmass tremor is taken into consideration. Quantitative consideration of all tremors including their location is impossible at the stage of convergence prognosis because of lack of this type of data. This paper presents results of roadway convergence prognosis compared to results of underground investigation. Conclusions formulated on that base allow in future similar designing works for obtaining more accurate results.

Jan 1, 2013

By Brian E. Perrine

Underground mining requires a variety of specialized equipment. With ever-changing mining conditions and methods, some mines have had to resort to purchasing existing industrial equipment and adapting it for underground use. Since this equipment is not made for underground mining or their specific task, the result is often lost time, money, and sometimes an unsafe working condition. One such application is the setting of a CAN. A CAN is a type of cylindrical secondary roof support made from a cement composite and encased in steel. The CAN has become popular because of its simple one-piece design that can handle heaving and sagging better than other available designs. ?Because of this exceptional ability to sustain load through extended convergence and displacement, the CAN is one of the most robust and stable standing supports in use today.?It also promotes better air flow due to the size and shape of the CAN. CAN size and weight have increased over time to handle more difficult mining conditions. Significant down time and inefficiencies with existing CAN setting machines at Twentymile Coal were directly due to the item in use not being designed to be task-specific. They were undersized with very limited movement. The miners had to take extra steps and precautions when setting CANs. Maintenance delays were significant. Twentymile Coal Company realized that they required a safer, more reliable and more efficient machine to handle and set CANs, and looked for a partner to develop a new design-specific machine. They worked jointly with J.H. Fletcher® engineering and sales to design and manufacture a machine specifically made for setting CANs. The objective was to produce a machine that would handle the conditions and methods that the mine required for setting CANs during longwall retreat. The resulting design had to be safe, stable, have a wide range of motion, be ergonomic, simple to use, and easy to maintain. The machine also had to improve efficiency. The resulting machine has been operating for approximately one year at Twentymile Coal and has been proven to improve safety, reliability, and efficiency. In conclusion, with the task-specific CAN Manipulator, the mine is able to better plan daily tasks with the knowledge that the machine will be available throughout a shift, and the employees will be safer because of the machine?s ergonomics, stability and safety. This has resulted in better productivity and a safer environment.

Jan 1, 2013

By Douglas Tesarik, Mark K. Larson, Habte Abraham, Heather E. Lawson

Dynamic failures, or "bumps", remain an imperative safety concern in underground coal mining, despite significant advancements in engineering controls. While many factors have been empirically linked to the occurrence of dynamic failure events, identifying a consistent, repeatable set of criteria within a field setting has proven elusive; conditions generally associated with dynamic failure might produce an event at one site, but not another. Conversely and more troubling, dynamic failure could occur where relatively few of these factors exist. The presence of spatially discrete, stiff roof units, such as paleo channels, are one such feature that has been linked to the occurrence of dynamic failure events. However, an empirical stratigraphic review investigating the relative frequency of discrete units in bumping versus non-bumping deposits indicates that no significant difference exists based on this criterion alone, and that instead an apparent relationship exists between reportable bump history and the overall character of the host rock with respect to stiffness. Due to the complexity of the bump problem, however, these results are not conclusive, as they do not take into account any variable other than the presence or absence of stiff members in the roof lithology; To weight the relative impact of changes in a single variable, such as the thickness or location of sandstone members, it must be examined in isolation-i.e. in a setting where all other variables are held constant. Numerical modelling provides this setting, and the effects of variability in a stiff discrete member in a hypothetical longwall mining scenario are investigated within the context of three stratigraphic "types'', as determined by the ratio of stiff to compliant stratigraphic members; Compliant, Intermediate and Stiff A modelling experiment examines changes in rupture potential in stiff roof units for each stratigraphic type as discrete unit thickness and location are manipulated through a range of values. Results suggest that the stiff-to-compliant ratio of the host rock has an impact on the relative stress-inducing effects of discrete stiff members. In other words, it is necessary to consider both the thickness and the distance to the seam, within the context of the host rock, to accurately anticipate areas of elevated rupture induced hazard; acknowledging the presence of a discrete unit within the overburden in general terms is an insufficient indicator of risk. Through modelling of anticipated changes in the placement and dimensions of discrete units within their stratigraphic setting, elevated rupture-induced bump hazard can be anticipated on a case by case basis. Were similar modelling studies conducted at mine sites in tandem with tracking of problematic discrete stiff units, areas of elevated rupture risk could be anticipated in advance of mining. Developing this predictive capability beyond identifying rupture potential in discrete roof members is essential to the eventual elimination of dynamic failure related worker injuries and fatalities. As stress is a necessary component in the occurrence of dynamic failure events, this finding helps to refine our understanding of the role of individual stiff, strong roof members in bumping phenomena, and suggests that a more holistic view of overburden lithology, combined with site-specific numerical modelling, may be necessary to achieve greater miner safety.

Jan 1, 2016

By Zhang Hongzhen

The fast convergence of boundary is a major problem of probability integral method, especially for the prediction of mining under thick alluvium, abandoned mine goaf, etc. To solve this problem and improve the accuracy of probability integral method, a modified model is constructed for surface movement and deformation based on theoretical analysis. In which, three weighted values i.e. 1, -1/t1, 1/t2 are set for the mining movement and deformation of three different major influence radius i.e. r1, R1, R2, respectively, then the parameters are selected as following: (1) Parameters are inversed based on the observation data, in which the subsidence factor q, deviation of inflection point s, displacement factor b are considered as generic parameters, the tangent of major influence angle tanß is modified as tanß2, that is the major influence radius r is modified as r2. (2) Inversion parameters of tangent of major influenceangle tanß or major influence radius r, based on the observation station edge data which beyond major influenc eradius distance from work-face mining boundary. The inversed tanß and r will be used as tangent of major influence angle tanß1 and major influence radius r1, respectively. (3) Other relevant parameters i.e. t1, t2, R1, R2, are calculated with the algorithm of this paper. A comparison experiment between the traditional and modified models has been conducted using the observation data from a observation station, the results show that in its central area, 58.6 percent of observation points accuracy is improved and 36.6 percent is decreased, while in its edge area, 61.5 percent is improved and 15.4 percent is decreased, totally, 68.6 percent is improved and 30 percent is decreased. Therefore, we can draw the conclusion that our modified model can improve the prediction predication accuracy, in particular, the boundary region.

Jan 1, 2014

By Peter Zhang, Daniel Su, Essie Esterhuizen, Mark Van Dyke, Berk Tulu, Dave Gearhart

"Roof falls in longwall headgate can occur when weak roof and high horizontal stress are present. To prevent roof falls in the headgate under high horizontal stress, it is important to understand the ground response to high horizontal stress in the longwall headgate and the requirements for supplemental roof support. In this study, a longwall headgate under high horizontal stress was instrumented to monitor stress change in the pillars, deformations in the roof, and load in the cable bolts. The conditions in the headgate were monitored for about six months as the longwall face passed by the instrumented site. The roof behavior in the headgate near the face was carefully observed during longwall retreat. Numerical modeling was performed to correlate the modeling results with underground observation and instrumentation data and to quantify the effect of high horizontal stress on roof stability in the longwall headgate. This paper discusses roof support requirements in the longwall headgate under high horizontal stress in regard to the pattern of supplemental cable bolts and the critical locations where additional supplemental support is necessary.INTRODUCTIONLongwall mining is the primary underground coal mining method in the United States and currently accounts for more than 60% of the underground coal production. The longwall headgate, as a passageway for the longwall crew, intake air, material supplies, and coal belt transportation, is critical for both safety and continuous production of the longwall panel. A roof fall in the longwall headgate would not only result in substantial interruption of production but could potentially cause injuries or fatalities. Rehabilitation of failed roof in the headgate would also expose miners to the risk of injuries. Roof falls in the headgate, though infrequent, mostly occur in the belt entry near the face. Considerable research has been conducted to determine the effects of various factors on headgate roof stability, as well as effective measures to support the roof in longwall mines in the Pittsburgh seam (Mark, Mucho, and Dolinar, 1998; Chen et al., 1998; Su and Hasenfus, 1995; Su, Thomas, and Hasenfus, 1999; Su, Morris, and McCaffrey, 2002; Su, Draskovich, and Thomas, 2003; Hasenfus and Su, 2006; Van Dyke et al., 2015). Previous studies have demonstrated that high horizontal stress and transitional roof geology are primary factors that cause headgate roof failure. These studies also showed that panel orientation, retreat direction, pillar sizes, and roof support played an important role in the stability of a headgate.In underground coal mines located in the eastern United States, the magnitude of the maximum horizontal stress is typically three times greater than the vertical stress, and about 40% greater than the minimum horizontal stress. Mark, Mucho, and Dolinar (1998) studied seven cases of headgate failures caused by high horizontal stress in different coal seams in the United States and stated that roof stability is affected, to a large extent, by rock type, entry orientation, and longwall orientation. The effects of horizontal stress can be summarized in these statements: (1) A laminated roof is very vulnerable to high horizontal stress. (2) Entries that are aligned with the maximum horizontal stress will suffer less damage on development than those perpendicular to it. (3) Horizontal stress concentration and relief depends on panel orientation, the direction of retreat, and the sequence of longwall panel extraction."

Jan 1, 2018

By Rob Thomas

"In Australia, a wide roadway is commonly defined as any roadway that is driven to a width greater than 5.5 m (18 ft). These roadways are typically required to enable the installation of longwall equipment (termed installation roads); however, other applications include the need to house conveyor driveheads and pre-driven recovery roads.As a result of the increasing size of longwall equipment and mine infrastructure, in some mines, roadway widths of between 9 and 12 m (30 and 39 ft) and are being developed.Accepting that these almost always constitute strategically important and often long-term roadways, this paper considers the use of: (i) an empirical roof support design model, which is based on over one hundred case histories, (ii) various roof support design principles, and (iii) commonly accepted strata management techniques.The paper demonstrates that wide roadways can be driven and supported to an acceptable standard providing due consideration is given to the prevailing ground conditions (including the quality of the immediate and upper roof strata, the Depth of Cover and the horizontal stressfield), the final width of the roadway and the required use of the roadway.INTRODUCTIONRoof behaviour and the associated roof support requirements in wide roadways, which are roadways typically driven to a width that is greater than 5.5 m (18 ft), are controlled by a number of key geotechnical and operational factors. The recognition of these factors is an important first step in the design process and it is imperative that each is considered in conjunction with local mine site information.The main points of note in this regard can be summarised as follows:• The greater the final width of the roadway, the greater the resulting surge in roof displacement on widening - note: a) see Figure 1 for a schematic illustration of the roof displacement trends typically measured during the development of the first pass and roadway widening, b) since displacement increases with roadway width, it is always recommended that the roadway width is kept to the minimum required and c) general buckling beam theory indicates that the capacity of any beams present in the roof will reduce in inverse proportion to any increase in roadway width squared (i.e., [final width2 -first pass width2] I final width2)."

Jan 1, 2010

By Abdolreza (Reza) Osouli

Determining the roof stability condition of underground coal mines in the Illinois Basin is sometimes very challenging. The roof stability of Illinois mines are mostly affected by two types of shales: Anna Shale and Energy Shale. These layers are sometimes weak in parallel bedding when subjected to horizontal stresses. The roof rocks in the Illinois Basin are are typically more moisture sensitive than the other coal fields. In this study the geotechnical properties of some of the shale units as well as limestone layers will be presented. The geotechnical properties of roof rocks consist of moisture content, unconfined compressive strength, slake durability, indirect tensile strength, and point load tests (Axial and Diametral). The correlation of indirect tensile strength versus diametral point load strength as well as unconfined compressive strength versus axial point load test are explored and discussed. These correlations will help in identifying the roof mass index and planning appropriate roof control measures. This study also evaluates the application of CMRR rock mass index for an Illinois coal mine.

Jan 1, 2014

By Andre Cezar Zingano

"The objective of this paper is to estimate the coal seam strength and the pillar safety factor for low coal seams using back analysis and rock mass characterization. The coal seam strength is very important to estimate both pillar capacity and mine section design. There are two approaches to estimating coal seam strength: (i) by geomechanics characterization of the boreholes cores; and (ii) by back analysis from pillars successes and failures, or some in-situ tests. For low coal seams (1.2 m, or 47 in.), the confinement of the center of the pillar is very important to defining global pillar strength because the low seam height increases the confinement of the pillar core, even in small pillars. We used in this case study one underground coal mine in the Parana State where the coal seam thickness is 0.8m the pillar height is 1.3m, the entry width is 5m and seam depth is 130m. A panel test was prepared to study the pillar behavior for use of the retreat mining method. The designed pillar size was 6x5m and 1.3m high with a predicted safety factor of 1.0 based on the Hoek and Brown failure criterion is 5.3 MPa. Once no pillar failure was observed, the pillar safety factor was assumed at 1.0 and the coal seam strength was backcalculated. The back analysis estimated the coal seam strength to be 6.2MPa. The confinement of the pillar center directly affects the coal pillar strength, and also the coal seam strength estimated by back calculation.IntroductionThe coal seam strength is very important to estimating pillar strength and mine section design. There are two approaches to estimating coal seam strength: (i) by geomechanics characterization of the coal seam using borehole cores; and (ii) by back analysis from pillar successes and failures, or some in-situ tests like panel test or ultimate pillar capacity (Salamon and Munro, 1967; Maleki, 1981; Peng and Dutta, 1992). For the first approach, lab tests (mainly triaxial tests) and borehole geomechanics descriptions (quality and quantity of the discontinuities) determine the coal seam strength by the Hoek and Brown failure criterion (Hoek and Brown, 1997). For the second approach, a panel test to study the pillar behavior can be built to define coal seam strength by back calculation. The safety factor for the pillars in the test is 1.0, based on the estimated coal strength from the geomechanics characterization. In this case, the probability of failure is 50%. If some pillar failure occurred, and the real pillar size was measured, the back analysis could be applied to define pillar strength and the coal seam strength."

Jan 1, 2015

By Renn Oler

Corrosion can often cause significant strength reduction and failure of steel rockbolts, thus demanding continuous rehabilitation and posing challenges to underground mines in maintaining long term ground support. The mining industry has traditionally applied galvanized and epoxy coatings for protection of ground support and reinforcement in corrosive environments due to cost considerations. However, under a harsh and corrosive groundwater condition with extreme pH levels, failure of the existing coated rockbolts often results in failure and falls of the mine roof, especially in long-term mine drifts or entries. To prevent the roof falls induced by corrosive bolt failure, DSI developed a new polymer coating, called ?Obduro AP coating,? to combat harsh and corrosive ground conditions. The new polymer coating was tested in extreme conditions to identify weaknesses and was found to be capable of handling highly corrosive mine water solutions. This paper highlights the challenges faced by underground mines with corrosive bolt failure and shows that the DSI Omega BoltTM can withstand the most corrosive ground conditions when it is coated in the new, economic Obduro AP coating.

Jan 1, 2014

By Michael Murphy

A multi-stage triaxial procedure has been developed for the enhanced servo controls and feedback systems at the National Institute for Occupational Safety and Health (NIOSH) rock mechanics laboratory. Due to the difficulty of preparing multiple rock specimens for single-stage triaxial tests at different confinements, multi-stage testing provides a huge advantage if only a few samples of coal measure rocks can be prepared from the drill core. A multi-stage test can provide mechanical properties, post-failure properties, and a complete failure envelope for a single specimen. For the multi-stage test procedure, a parameter used to define the slope of the stress-radial strain curve was developed and monitored in real time in order to successfully predict peak strengths at different confining stages. For this paper, multi-stage tests have been conducted on sandstones of varying strengths, including Berea sandstone which has well-documented properties, and fine-grained and coarse sandstone from a western US coal mine. For the tests conducted on the fine-grained sandstone, it was found that the ramp rate was an important factor in the success of obtaining peak strengths during the multi-stage tests. For each rock type, a table including Young?s modulus, Poisson?s ratio, unconfined compressive strength, friction angle, cohesion, residual friction angle, and residual cohesion are reported. The values from these tables have been used as input parameters for projects at NIOSH requiring numerical model input parameters.

Jan 1, 2014

By Robert J. Coutts, Dan A. Payne

"The Broadmeadow mine is a punch longwall mine owned and operated by BHP Billiton Mitsubishi Alliance (BMA) in the Bowen Basin of Queensland, Australia. In 1999, an exploratory adit was driven as part of the feasibility study for the establishment of the mine. Subsequent development of the mine in 2004 started some distance away from the initial test adit. Ten years later, the trial adit would be used as the headgate of the 5'h longwall panel. However, multiple roof falls had occurred in a heavily jointed area over a distance of 1, 000 ft (300 m) during the past 10 years. Due to the immediate coal roof, low stress environment and time, some of these falls had progressed to 38 ft (11.5 m) above the mining floor. As a result of the extensive work involved and safety implications of trying to recover the roof falls conventionally, a strategy was developed to fill these roof falls with a cement based product from the surface, down boreholes, and redrive the roadways through the consolidated roof fall material. This paper describes the process of rehabilitating these roadways, the results when the roadway was redriven and the headgate performance as the longwall mined through the area.INTRODUCTIONBMA operates 7 open cut and 2 underground mines in the Bowen Basin of Queensland, Australia producing over 50 mt per year of high quality coking coal. As a result, BMA has established over 150 miles (250 km) of open cut highwall.Broadmeadow Mine is a punch longwall mine located 22 miles (35 km) north of Moranbah in Queensland, Australia on the western limb of the Bowen Basin Coal Measures (Figure 1). Broadmeadow Mine commenced development in 2004 and began longwall operations in 2005. Broadmeadow is currently completing the fifth longwall panel and produces over 4 Mt per year of high quality coking coal. Mining is undertaken in the Goonyella Middle Seam, which is 21 to 25 ft (6.5 to 7.5 m) thick in the current mining area.The mine layout required the use of an old exploratory gateroad as the headgate of its 5th longwall. This gateroad had experienced numerous large roof falls and required extensive rehabilitation."

Jan 1, 2010

By Feiya Xu, Syd S. Peng

"As a highly efficient and new surveying and mapping technique, 3D laser scanning technology has been gradually applied to surface subsidence monitoring in mining areas. 3D laser scanning technology was used to monitor the mining subsidence in a coal mining area in this paper. Based on the 3D laser scanning data obtained in March, May, and December 2016 in the studying mining area, the surface subsidence basin and points deformation were acquired. The 3D laser scanning data were compared with that of the conventional surface movement surveying method. The results show that the 3D laser scanning technology could obtain the data of the subsidence basin more efficiently and reflect the true shape of surface subsidence caused by mining. The maximum surface subsidence obtained by 3D laser scanning technology was 3.60m, while the conventional surface movement surveying was 3.56m; the relative observation error between 3D laser scanner and the conventional surface movement surveying was less than 10%. Therefore, it is feasible to apply 3D laser scanning technology to monitor surface subsidence in coal mines.INTRODUCTIONWith the over-exploitation of coal resources, the problem of surface subsidence has become the focus of attention (Peng, 2011; Guo Wenbing, 2012). Setting up observation stations for surface movement was the traditional method to study the characteristic of surface subsidence and its parameters. At present, hundreds of observation stations have been set up in longwall mining, and a large number of measured data have been obtained (Ministry, 2017). However, due to the length of time surveying requires, great workload in the field, the high cost of observation, and difficult protection for monitoring points, conventional observation stations for surface movement have not met the research on surface subsidence. Therefore, as a new surveying and mapping technique, 3D laser scanning technology has been gradually used for surface subsidence monitoring in mining areas (Ma Liguang, 2005). Li Qiu, Qin Yongzhi, and Li Hong (2006) first proposed 3D laser scanning technology in the application of monitoring surface subsidence in 2006. It was showed that the 3D laser scanning technology had obvious advantages in efficiency and accuracy of data acquisition than other methods of deformation monitoring technology of surface subsidence (such as total station, precision level technique, GPS, etc.). Subsequently, Zhang Shu, Wu Kan, and Wang Xiang (2008) and Chen Ranli and Wu Kan (2012) analyzed the feasibility and precision of 3D laser scanning in subsidence monitoring, concluding that the 3D laser scanning can be used to obtain the subsidence basin and the monitoring precision can reach millimeter. Hu Dahe, Wu Kan, and Chen Ranli (2013) introduced the data processing method of 3D laser scanning for surface subsidence in detail. On the basis of a case study, the subsidence basin in subsidence area was obtained, which reflected the shape of mining subsidence basin intuitively and comprehensively. Wang Qisheng, Wu Kan, and Zheng Ruyu (2010) carried out the research on prediction parameters of mining subsidence by using 3D laser scanning data and got the parameters of major influence angle and the offset distance of inflection point. Meng Wanli, Cai Lailiang, and Yang Wangshan. (2017) made a profile analysis for the 3D view of the surface subsidence using 3D laser scanning data and put forward a “Geomagic” method of surface subsidence prediction."

Jan 1, 2018

By Weijia Guo

With the exploitation of coal resources, a large area of land had been affected by surface subsidence, causing conflicts between man and land to become more conspicuous by the day, affecting the life of general public, and constraining further development of the land. This paper predicts the subsidence areas according to the 10-year mining plan of the Jibei mining district as an example. A plan of environmental management was developed based on sciences and practical economics.

Jan 1, 2006

By Francis S. Kendorski

High-extraction mining of coal and other stratified minerals has a predictable effect on the surface and subsurface. Impacts on ground waters in overlying strata and on surface waters, that are associated with overlying sequential zones of collapse, fracturing, aquiclude, constrained strata, and surface disturbances can be anticipated. Since first quantified around 1979 in Bureau of Mines sponsored contract research work and others (and often adopted by state regulators), with zone extents based upon multiples of mined seam height of 24 to over 60 for the fractured zone, much new data have become available. In examining the sources of data and the methods and intents of the researchers of over 65 case histories, it became apparent that the strata behaviors were being confused with overlapping vertical extents reported for the fractured zones and aquiclude zones depending on whether the researcher was interested in water intrusion into the mine or in water loss from surface or ground waters. These more recent data, and critical examination of existing data, have led to the realization that the former "Aquiclude Zone" defined for its ability to prevent or minimize the intrusion of ground or surface waters into mines has another important character in increasing storage of surface and shallow ground waters in response to mining with no permanent loss of waters. This zone is here named the "Dilated Zone." The existence of the dilated zone explains the ratios of up to 60 times the mined thickness. Surface and ground waters can drain into this zone, but seldom into the mine, and can eventually be recovered through closing of dilations by mine subsidence progression away from the area, or filling of the additional void space created, or both. A revised model has been developed which accommodates the available data, by modifying the zones as follows: ? collapse and disaggregation extending 6 to 10 times the mined thickness above the panel ? continuous fracturing extending approximately 24 times the mined thickness above the panel, allowing temporary drainage of intersected surface and ground waters ? development of a zone of dilated, increased storativity, and leaky strata with little enhanced vertical permeability from 24 to 60 times the mined thickness above the panel above the continuous fracturing zone, and below the constrained or surface effects zones, whose thickness or existence is dictated by the zones above and below ? maintenance of a constrained but leaky zone above the dilated zone and below the surface effects zone, whose thickness or existence is dictated by the zones above and below ? limited surface fracturing in areas of extension extending up to 50 ft or so beneath the ground surface

Jan 1, 1993