Search Documents

By U Nyberg

Peak particle velocity (PPV) and distance measurements from a single-charge blast test conducted by Swedish researchers in iron ore at the Kiruna Mine in northern Sweden are presented. They are used along with theoretical PPVs calculated using an equation based on hydrodynamics to determine a damage distance range caused by a single charge. This equation, which relates PPV to explosive properties, charge geometry, and distance from a charge, was then applied to a charge of different geometry that was used in drift rounds. A comparison between calculated and measured PPVs suggests that the stoping holes likely damage the easer hole locations, and the easer holes produce damage to the perimeter hole locations. The practical effect is that typical damage limit predictions based on measurements conducted in fresh or undamaged rock are conservative. This suggests that even when perimeter control is not exercised in drifting (i.e., the perimeter holes are fully loaded), the resulting damage may be less than normally expected due to the wave damping effect of the pre-damaged rock. Due to the damping effect, poor perimeter blasting practices are somewhat self correcting. However, it must be strongly emphasized that well-engineered blast designs with perimeter control are highly beneficial in relation to both economic and safety aspects.

Jan 1, 2011

By John Petty, John Loviza

Single sentence describing content-- "The best ally an Explosives Engineer can have in a court of law is a regulations enforcer stating all codes and standards were met on a jobsite".

Jan 1, 1996

By Weyman CT Ngain, Brian J. Kennedy

Innovative chemically sensitised bulk emulsion explosives and pump delivery systems have provided contractors participating in the highly competitive Hong Kong underground construction market with a safer and more cost effective approach to loading explosives.

Jan 1, 1997

By Miles Huntly

This paper will discuss the ideas and actions that led to the development of a Drill Improvement Team at an open cut coal mine in Australia. It will show significant cost savings can be attained by forming a focused Team derived from all the participants that go into drilling a blast hole

Jan 1, 1999

By C H. Dowding, P W. Linehan

Many of the technical and non-technical or human problems associated with blasting can be minimized through a proper preconstruction test-blast program.

Jan 1, 1986

By Jim Simpson, John Waller, Scott Stewart

The authors review the evolution of drilling and blasting procedures at this West Virginia surface coal mine where management seeks continually to improve and update the drilling and blasting programs. Today's operations require efficient programs which include quality control to maximize production and minimize the public's sensitivity to the blasting events.

Jan 1, 1992

By Sandra K. Penttinen

A difficult blasting project can go very smoothly when every precaution is taken prior to and during the blasting procedures. These precautions include conducting careful preblast condition surveys of nearby structures, initiating a good public relations program prior to the beginning of the blasting, and following a good safety program during the blasting procedure.

Jan 1, 1994

By Mark S. Stagg, David E. Siskind, Stephen V. Crun, Willard E. Pierce

The USBM is studying the impacts of low-frequency blast vibrations on residences to assess both response and cracking potential. Complementing coal mining sites monitored in the midwest and east, vibrations were analyzed at a major construction site in southern Florida where potentially serious low-frequency blast vibrations were believed to exist.

Jan 1, 1996

By J Lyall Workman, Peter N. Calder

Flyrock can be a serious hazard associated with blasting. Many surface blasting accidents involving injury result from excessive flyrock beyond the protected blast zone. Numerous cases of equipment damage at the mine, quarry or construction site have resulted from flyrock. Fragments propelled beyond the property limits of the operation have also caused injury and damage.

Jan 1, 1994

It is a case study of huge rock-mass, loosened out from the parent rock-body, & posing a potential danger to structures down below the slope on which this rock mass was standing. Case was dealt in two phases, by tying/stitching the rock mass to the parent rockbody and breaking it using controlled blasting technique.

Jan 1, 1997

By Inc. The HDH Group

The Alternative Risk Market is defined as the segment of the insurance market that is made up of self insurance, risk purchasing groups, risk retention groups and captives. It is commonly referred to as the alternative to the traditional market, even though more the majority of companies today are insured through the alternative risk market than the traditional market.

Jan 1, 2007

By Todd B. Harrington, Dennis M. Lydon, Walter B. Sudweeks

Heavy ANFO products made by mixing ANFO (or AN prills) with a relatively small amount of emulsion (typically 15-30 percent) have become very popular in recent years. They are less expensive than straight, sensitized emulsion and maintain the good shooting characteristics of ANFO but have higher bulk strengths. Their use, however, is generally limited to larger diameter, dry boreholes. Smaller diameter, wet-hole quarries have not been able to widely utilize this low cost bulk product.

Jan 1, 1989

By R E. Otterness, M S. Stagg

The U. S. Bureau of Mines conducted 22 full-scale blasts to determine the effects of delay and explosive type on fragmentation. The shots were conducted over a period of 7 years in three limestone quarries and one granite quarry. Hole diameters, bench heights, and number of holes varied from 6.4- to 14-cm, 6.7- to 14-m, and 4- to 24-holes, respectively. Explosive performance and actual firing times were measured and screening was used to assess the fragmentation.

Jan 1, 1995

By F Hunyadi

The seismic effects resulting from blasting are still a problem today although a great deal of research has been conducted in this field. A great amount of data defining the seismic effects can be collected with the proper instrumentation, however because of the difference in building materials, construction methods and foundations the characteristics of the seismic wave can not be directly correlated to the building response and possible damage.

Jan 1, 1975

By Yoshihiro Moriyama, Toshihiro Okitsu, Ryouichi Banno

The fracturing composition using the gas pressure generated by the thermit decomposition reaction gives the following performances.

Jan 1, 1995

By Shannon Studden, Angela King, Allan Koski

Cliffs Natural Resources is an international mining and natural resources company with over 160 years of history. A member of the S&P 500 Index, the company is a major global iron ore producer and a significant producer of metallurgical coal. Throughout its history, employees have been the foundation of the company’s success, which has long embraced a focus on continuous business improvement.

Jan 1, 2014

By Peter G. Bellairs

The traditional concept of Optimum Drill and Blast is that it is achieved when ore is produced at the lowest unit cost and due to the complexities of most mining operations represents a band which extends either side of an overall cost minima. The above definition implies that Optimum Drill and Blast is static and once blasting is within the band around the cost minima then the process is optimised. However mining operations are not static with many events both long and short term impinging on the cost structure and productivity.

Jan 1, 1995

By T Guiliani, F Ottuonye

Explosives casting is gaining increasing popularity as an overburden removal method in strip mining because the coats of using explosives to cast a percentage of the overburden to the spoil are lower than the costs of using stripping shovels or draglines to do all the overburden removal. This is due to the rising capital and operating costs of draglines and shovels.

Jan 1, 1989

By Ed Jr Smith, Calvin J. Konya

The purpose of this paper is to describe the case history of a blasting project conducted jointly by Precision Blasting Services and Cherokee Explosives. It is the intent of the authors to show how blasting could be done in controlled fashion near very expensive computer controlled machinery. The job was done in minimal time with no complaints or allegations of damage in spite of the fact that blasting was conducted within five feet of the equipment and with the 32 acre plant fully operational, with machine operators working within 10 feet of the blasting site.

Jan 1, 1986

By Dale Preece, Stephen Chung, Richard Jensen

DMCBLAST_3D is a three-dimensional extension of the proven two-dimensional rock blast modeling code, DMCBLAST. DMCBLAST has been under development since 1987 and has successfully predicted the physics, mechanisms and results of a number of different types of rock blasting including, coal mine bench blasting, mineral mine choke blasting and underground stope blasting. Substantial effort has gone into the qualification and verification of DMCBLAST by comparing computer code predictions with real blasts in the field. Comparison with field data has also provided significant guidance to the development of the code.

Jan 1, 2001