Search Documents

By V. Vogt

During the phosphating of car bodies containing aluminium, the employed phosphating chemicals zinc, manganese and nickel are, for thermodynamic reasons, only used to a limited extent for the desired surface coating. The major proportion of these metals is discharged together with the incidental cryolite-containing phosphating sludges and the rinse water. Commissioned by the German Federal Ministry of Education and Research (BMBF), the Institute of Mineral and Waste Processing, Waste Disposal and Geomechanics at the Clausthal University of Technology has developed a two-stage process for the production-integrated recovery of the dragged out chemicals and for closing the rinse water cycle for Audi AG. During the first stage, the phosphating chemicals are recovered by means of leaching. In the second stage, the rinse water is treated by means of electroflotation followed by an ion exchanger.

Jan 1, 2014

By Leming Ou, Qiming Feng, Yiping Lu, Pengyu Zhang, Qing Shi, Kun Liu, Guofan Zhang

"This paper introduces the mineralogical analysis of certain polymetallic copper-zinc ore in China with the aim of improving the flotation process. The main valuable elements, mineral phases and compositions of run-of-mine ore were inspected by the X-ray Fluorescence (XRF) and chemical analysis. For a deep known of the old process defects, Mineral Liberation Analysis system (MLAs) was employed to investigate the minerals liberation degree of selected key slurry points. Analysis results show that the run-of-mine ore belongs to the original copper-zinc polymetallic symbiotic ore at low oxidative level, which mainly contains 0.16% Cu, 4.43% Zn and 0.88% Sn. Gangue minerals are mainly silicate minerals, and zinc mineral is sphalerite. MLAs test illustrates that about 86% sphalerite has been dissociated in zinc flotation feed. In the current flotation process, over grinding of sphalerite monomer and insufficient liberation of intergrowths are the key problems need to be solved imminently. Up to this point, a new process consisted of two steps roughing unit is submitted in this research. It contributes two positive effects on zinc flotation performance: (i) separating sphalerite monomer timely to decrease overgrinding; (ii) improving zinc minerals intergrowths liberation efficiency. Flotation results indicate that the zinc concentrate grade increased 0.90% and the recovery improved 0.96% in the new flotation processINTRODUCTION Mineralogical analysis mainly focusses on solving mineralogy problems in minerals processing, assisting in minerals behaviors prediction and control for separation engineering (Falkovich, et al., 2001; Hillier, et al., 2003; Schouwstra and Smit, 2011). Process defects searching becomes its ordinary work, and flotation optimization appears to be its targets gradually. For example, Lucky Friday mine company (Idaho America) fails to obtain qualified lead concentrate as the change of ore properties (Nadoll, et al., 2011). Mineralogical analysis ascertains that there are too many dissociated sphalerite, pyrite and gangue particles exist in lead concentrate. According to this, more cleaning units are added to solve problems effectively. Kanowna Belle mine (Australia) takes a flash circuit in operation successfully with the aim of optimize flotation process, under the helps of mineralogical analysis and industrial test (Newcombe, et al., 2013). Lotter N.O. (2011) gives a deep description on how mineralogical data assisting mineral processing engineers to design and optimize flowsheet. For decades, quantitative and automated mineralogy techniques (Andersen, et al., 2009; Gu, et al., 2012; Oghazi, et al., 2009; Yu, et al., 2007) get well developed and hugely improve the veracity and repeatability of minerals properties measurement. Among these, MLAs (Gu, 2003) provided by JKMRC (Julius Kruttschnitt Mineral Research Center) is critically acclaimed all over the world. This analysis system can measure mineral phases composition and content, particles size, minerals occurrence and liberation degree directly."

Jan 1, 2018

By Junwei Han, Kai Xue, Wenqing Qin, Tan Xu, Fen Jiao, Lianbing Cai, Wei Liu

"The research aimed at solving the problem of the stacked spent magnesia-chrome refractories using in non-ferrous metal smelters, which contain various heavy metals and are considered as a hazardous waste. The purpose of the research is to recycle the spent refractories environmentally and economically using gravity separation and flotation to obtain metal concentrates for smelting and using chloridizing volatilization to remove the trace metals from tailings, providing raw material to reprocess magnesia-chrome refractories. In the course of the study, laboratory techniques for the preparation of experimental samples of spent magnesia-chrome refractories were developed including the sequence of operations of material grinding, gravity separation, tails regrinding, flotation, filtration and subsequent unification of concentrates, filtration and chloridizing volatilization of tails, and collection of volatiles. Laboratory tests carried out on several types of samples of spent magnesia-chrome refractories from different smelters showed that gravity separation provided increase in quality of concentrates including about 80% metals (including Ag, Pb, Bi) and flotation separation provided increase in recovery of concentrates under the condition of 200g/t of emulsified kerosene, and 500g/t of combined collector. Based on combined technology of gravity and flotation separation, about 90% metals were recovered from the refractories by a closed-circuit test and the total concentrates contained 40% metals, which can be returned to smelting process as a feeding. Because a small amount of metal in raw materials will seriously affect the performance of refractories, chloridizing volatilization is necessary for removing the remaining 10% metals from tails mixed 8% coke and 13% magnesium chloride at a temperature of 1200°C. Thus, the tailings can be reused as a raw material for new refractories.INTRODUCTION Magnesia-chrome refractory has been used extensively in various industries such as secondary metallurgy, non-ferrous furnaces and cement making due to their high temperature stability, low thermal expansion and outstanding erosion-corrosion performance at high temperatures (Gotod et al., 2005; Vezza et al., 1997; Gregurek et al., 2015). Generally, the magnesia-chrome refractories are produced from a mixture of magnesia and massive variety of chrome ores. However, massive chrome ores are being depleted throughout the world. Even more serious is that the heavy metal chromium (Cr) can transfer into soil and water, which will have an influence on the survival and development of human beings (Zhao et al., 2006; Jiang et al., 2004; Qintie et al., 2013). As a result, regulations treating spent magnesia-chrome refractories as potentially hazardous waste are being enforced, making their disposal difficult and expensive."

Jan 1, 2018

By L. Bbosa

Positron Emission Particle Tracking (PEPT) and the Discrete Element Method (DEM) are used to investigate Power Draw in a laboratory scale tumbling mill. The mill is run dry in batch mode at different speeds using mono-size charge of glass beads, and is mounted along with a torque transducer to measure power. Particle tracking information from PEPT is used to reconstruct the motion of glass beads and infer the overall charge behavior, while DEM is employed to simulate particle motion and interaction, with collision mechanics calculated using the Hertz-Mindlin contact model. For PEPT and DEM data, the product of torque and average angular velocities in discrete cells are accumulated to obtain mill power. This method is found to be within statistical agreement with measured power for all tests. Spatial distributions plotted from this approach highlight the regions of the mill that draw the greatest power. A second technique to obtain Power Draw from DEM data which sums particle forces against the mill geometry is similarly found to accurately predict mill power with lower statistical error. Keywords: Power Draw, PEPT, DEM

Sep 1, 2012

By John A. Herbst, Ming Song, Xiangjun Qiu

It has been known for sometime that as wear occurs in tumbling mills there is an associated change in mill throughput. These changes have traditionally been simplistically, attributed to “mill volume effects”. New high fidelity simulation tools (involving DEM, CFD and Breakage models) are now giving new “microscale” insights into the complex interactions that occur between evolving lifter/liner profiles and breakage. The study described here shows that these new tools can allow the design of wear part profiles which will maximize mill productivity over the entire life of a liner/lifter system.

Jan 1, 2003

By Shibayama A.

In this research, an investigation of a process to selectively remove arsenic (As) and antimony (Sb) contained in enargite (Cu3AsS4) and tennantite/tetrahedrite ((Cu1,Fe)12(As,Sb)4S13) copper resources by leaching and precipitation were performed. First in the leaching process, the target was to selectively leach As/Sb and reduce their contents in the ores to <0.5 wt% followed by a second process to remove As/Sb dissolved in solution for environmental control. Enargite ore contained 3.65 wt% As while tennantite/tetrahedrite ore contained 5.40 wt% As and 4.85 wt% Sb. Alkaline leaching using NaHS?NaOH media at varying experimental conditions (temperature, pulp density, time, reagent concentrations) were performed to investigate the process. As/Sb precipitation studies were also performed to control high As/Sb concentrations in leach solutions by using elemental sulphur (So). Results from leaching studies showed that over 99% of As/Sb in the impure copper ores can be removed and their contents in the final solids reduced to <0.5 wt%. It was also established that such very high leaching could be achieved at 80°C within 1?6 h and pulp densities as high as 1000 g/L. The study also revealed that leach solution containing very high As/Sb concentration ranging from 5 to 20 g/L can be used as fresh solution for leaching of fresh ores until concentrations exceeding 35 g/L when it was sent to precipitation circuit for As/Sb removal. Addition of elemental sulphur at 90°C and fast cooling to 30°C allowed over 60% As/Sb precipitation and removed as Na3AsS4 and solution with reduced As/Sb concentration to leaching circuit for continuous use. Keywords: Enargite; Tennantite/Tetrahedrite; Selective Leaching; Precipitation; Sodium hydrosulfide;

Sep 1, 2012

By Z. Y. Lan

Bioleaching of marmatite with various mixed cultures of microorganisms was investigated. The experiments were carried out in shaking flasks with iron-free nutrient and the pulp density of 10% wt/vol at the temperature of 30?. The results show that zinc is preferentially leached before iron. The leaching rate of zinc with the mixed culture of Acidithiobacillus ferrooxidans, Acidithiobacillus thiooxidans and Leptospirillum ferrooxidans is 62% in 18 days. The leaching rate of zinc with the mixed culture of Acidithiobacillus ferrooxidans and Acidithiobacillus thiooxidans is nearly the same as that with the mixed culture of Acidithiobacillus ferrooxidans and Leptospirillum ferrooxidans (45% versus 50%). SEM and EDX analysis of the leaching residues indicate that a solid product layer composed of iron sulfide, elemental sulfur and jarosite accumulates in the mineral surface and becomes a barrier to the dissolution of marmatite. The bioleaching of marmatite follows the shrinking core product layer model. When the product layer increases and becomes insoluble, the leaching rate is controlled by the diffusion through the product layer and slows down. When the product layer decreases or becomes a porous layer, the leaching rate is controlled by chemical reaction and enhanced dramatically.

Jan 1, 2014

By D. R. Nagaraj, Raymond Farinato

Water constitutes one of the most valuable resources employed in mineral recovery and processing. Identifying potential problems encountered in mineral processing in waters unusable for drinking or agriculture (including seawater and even hypersaline waters), understanding chemical factor interactions, and optimization of flotation reagents will greatly expand our ability to create more sustainable beneficiation technologies. The current paucity of our knowledgebase regarding high salinity effects on flotation clearly signals a need for a significant research effort. We report here results of a study designed to probe effects of pulp chemistry on metallurgical performance in the flotation of Cu and Cu-Mo ores in saline waters. The results clearly demonstrate that pH (more correctly dosage of pH modifier to target a pH set point) has the most significant effect on Mo recovery when using seawater. This is linked to the formation/precipitation of Mg(OH)2 when pH = 10.3 (in seawater). The type of pH modifier used, NaOH or Ca(OH)2, had no impact on Cu or Mo recovery, indicating that Ca2+ ions were not involved in any reduction in Mo recovery in the pH range of 9-11. Our results in tap water spiked with either Ca2+ or Mg2+ ions in the same pH range (controlled by NaOH), confirmed that Ca2+ ions had no effect on Cu or Mo recovery, but that addition of Mg2+ ions had a severe adverse effect on Mo recovery at pH = 9.5, and to a lesser extent on Cu recovery. The onset of Mg(OH)2 precipitation occurred at a higher pH, and the adverse impact of Mg(OH)2 on Cu recovery (and perhaps Mo recovery as well) was less, in sea water than in tap water spiked with Mg2+. These effects are attributed to the mitigating role of the high electrolyte concentration, notably NaCl.

Jan 1, 2014

By F. Karakas

In this investigation, one of the most energy consuming stage of the cement manufacturing process, grinding stage, was studied. The aim of the study is to reduce the energy consumption. Optimum operating parameters were determined. Experimental studies were performed at three differ-ent stages. Grinding of limestone, clay and marl which are the main components of the cement, to approximately below 90 microns, was the first stage of the cement grinding. At this stage, effect of feed size and ball charge were investigated. At the second stage, the Bond work index of clinker and additives (slag, trass, limestone and gypsum) was found separately. After forming composite cement with clinker and additives, the Bond work index of this mixture was also determined, thus the results of separate grinding and grinding of mixture were compared. The Bond work index of mixture was found as 13.59 kWh/t, while the arithmetic mean of the Bond work index values of components was 14.90 kWh/t. Finally, clinker and additives (slag, trass, limestone and gypsum) were ground under the same conditions. At this stage, laboratory type of ball mill was used in order to understand grinding characteristics of the cement components. As a result of the experiments, it was found that energy consumption for the grinding will be lowered if the mills with 38 % ~ 40 % ball charge are used in the cement grinding. Moreover, grinding with mixture of clinker and additives gave better results than separate grinding of these components in terms of energy consumption.

Jan 1, 2014

By Kwan Ho Kim

In this study, free fall tests are conducted with the objective of understanding the breakage properties of waste concrete for the guide of the direction of the better comminution process. Waste concrete of 75mm×53mm is tested at various drop heights with or without heat pretreatment. Test results indicate that a block of waste concrete does not break by free fall, but eventually breaks by repeated free falls. The number of free falls required for complete separation of large aggregates from the cement mortar considerably reduced when the samples were heated at 400?. Therefore, a great energy saving can be obtained when heating the waste concrete prior to crushing. The energy saving was found to be dependent on the height of free fall but in all cases, was still large enough to offset the additional energy required for heating. Also, it was found that the heat pre-treatment gives an additional advantage in that it produced cleaner recycled aggregates. This may result from easier detachment of cement mortar from the aggregates due to weakening of bonding forces by heating. By analyzing the size distribution of the crushed product, a free-fall breakage model is developed using the particle breakage ratio and the breakage pattern. The developed model can be used to predict and to analyze waste concrete processing circuit.

Jan 1, 2014

By D. Jamróz, A. Surowiak, T. Niedoba, P. Pieta

"The separation of coal material of three types of coals originating from three various Polish hard coal mines (types 31, 34.2 and 35, according to Polish nomenclature, which were steam coal, semi-coking coal and coking coal) into particle size fractions and then into particle density fractions was done and then the following parameters were measured for each particle size-density fraction: combustion heat, ash contents, sulfur contents, volatile parts contents, analytic moisture. In this way a 7-dimensional vector of data was created. Using methods of factor analysis the important features of coal were selected, which decide about their membership to individual types. To evaluate the appropriateness of the applied method the Bartlett’s sphericity test as well coefficient of Kaiser-Mayer-Olkin (KMO) were used. To select important factors the Kaiser criterion and Cattell’s scree test were used. The obtained results were compared with the results obtained in previous works by means of observation tunnels method. The results showed which particular features are crucial to define the type of coal what is also important to select appropriate method of its enrichment.INTRODUCTION Coal extracted from the mine is often a mixture of coals of various quality originating, for example, from various coal layers. One of the most important issues is to determine its quality, what means to verify if it fulfills certain requirements. Usually, such parameters as combustion heat, ash contents, sulfur contents, volatile parts contents and analytic moisture decide what the coal quality is (Drzymala, 2009). Such investigations are expensive and time consuming. That is why it seems to be important to determine the mutual connections and interactions between them what would make possible to reduce the amount of the necessary parameters. This issue was already investigated with successes in several works [Jamróz and Niedoba, 2013; 2014; Niedoba, 2015]. This work is another approach to this problem. Here, the investigation of possible reduction of researched parameters was done on the basis of the factor analysis. The obtained results confirm the earlier observations."

Jan 1, 2018

By F. Göktepe

Flotation gases and conditioning of the pulp with them are one of the important parameters of flotation and should be taken into account especially in the flotation of sulphide ores. In this study, flotation of pure chalcopyrite and pyrite samples were investigated with air, oxygen and nitrogen as flotation gas and the effect of conditioning with these three gases also were performed. Flotation gas was introduced for 5min, 10min, 15min and 20 min. For chalcopyrite flotation there was no drastic change in recovery when air, oxygen and nitrogen were used as flotation gas but conditioning the pulp with oxygen for 10 minutes increased the recovery about 8% where pulp potential has been approximately 25 mV with chalcopyrite and 150 mV with platinum electrodes. Conditioning with all three gases decreased the pyrite recovery by about 20% with 20 minutes conditioning. Pulp potential decreased in the presence of nitrogen while conditioning with air and oxygen increased the pulp potential for both electrodes. Generally potential increased for both minerals with oxygenation and aeration time but it was stable or slightly decreased with nitrogenation. Comparison of the gases showed that the different flotation gases do not effect flotation recovery but conditioning the pulp with these gases at pre-flotation effects chalcopyrite and pyrite flotation recovery, most dramatically pyrite.

Jan 1, 2014

By T. X. Hu

Pyrite ore is one of the main raw materials in the production of sulfuric acid. For a long time, the raw material containing the pyrite, which is used to produce sulfuric acid, generally contains S only 32%~45%. A plenty of residue from the sulfuric acid production contains 40%~50% Fe and 1%~2% S. Some of the residue also contains Cu, Pb, Zn and other harmful elements like As, thus it pollutes environment seriously and is solid waste. The research on comprehensive utilization of the residue has been made by many scholars. Through the study, the residue can only be used to pro-duce iron concentrate and the iron oxide red pigment. But because of the complex techniques, the low recovery, the low grade of iron concentrate , high sulfur in iron concentrate, causing second waste residue and the environmental pollution, the residue is mainly used as an accessory material in the production of cement, and is of a low value. Therefore, the iron resource in pyrite has not been used efficiently until now. In the paper, the flotation condition test, the flotation open circuit test and the flotation closed circuit test to produce high-purity pyrite concentrate with the low-grade pyrite ore in oceanic ore deposit have been carried on. Flotation reagent scheme of sulfuric acid used as activator and butyl xanthate as collector is determined. After four times depth cleaning, high-purity pyrite concentrate containing 52.82% S, 44.29% Fe, and only 2.89% impurities has been obtained. The S recovery is 99.13%, and the Fe recovery is 96.00% in the high-purity pyrite concentrate. The oxidizing roasting depth desulfurization experiment of the high-purity pyrite concentrate has been conducted. The results show that the Fe grade in the residue obtained is 68.58%, the content of S is 0.25%, the content of P is 0.0084%, the content of As is 0.0065%. The residue is a kind of high-quality iron-smelting raw material. Based on the above experiments, the industrial experiments on producing high-purity pyrite concentrate with the low-grade pyrite ore, and producing sulfuric acid and iron concentrate with high-purity pyrite concentrate have been done. The results indicate that the high-purity pyrite concentrate with the S grade of 51.24%, the Fe grade of 44.15% has been obtained. The iron concentrate obtained with 65.73% Fe and 0.23% S is a sort of high-quality iron-smelting raw material applied to the production of steel and iron smelting. Through the experimental study, the sulfur and iron resources in the pyrite ore have been recovered and utilized efficiently.

Jan 1, 2014

By Yuexin Han, Wenbo Li, Yan Shan, Yanjun Li, Shumin Zhang

"With the accelerating pace of resource extraction, the quality of resources is decreasing, and the old tailing dams which have served for several decades have become the focus of attention. The secondary recovery of valuable metals in the tailings is an important aspect of the comprehensive utilization of tailings. The average iron content of iron tailing is 8%-12% in China. The research aimed at exploring the low-cost and efficient technical route to recycle eastern tailings of Anshan iron mining area. The purpose of the research is to scientifically find the rational conditions of magnetizing roasting and to provide an increase in recovery and quality of concentrates. The eastern tailings of Anshan mining area belong to high silicon bearing iron tailings, iron mainly exists in form of hematite-limonite with an iron grade of 10.60%, the main component of gangue is SiO2 with a grade of 76.22%. In order to reduce the influence of the tailings on the environment, fluidized magnetizing roasting and low intensity magnetic separation for the eastern tailings of Anshan mining area were carried out to improve the utilization of the tailings. The results indicated that an iron concentrate with an iron grade of 65.30% and a recovery of 85.85% could be obtained under the conditions of gas flow rate 8 m3/h, H2 concentration 50%, fluidized magnetizing roasting temperature at 600? for 20s. Phase analysis, magnetism analysis and XRD analysis on roasted materials indicated that hematite-limonite could be transformed to magnetite during the fluidized roasting, then the effective separation of iron and gangues could be made easily by the weak magnetic separation. INTRODUCTION It is universally acknowledged that the grade of iron ore in China is low, the output rate of iron ore tailings is high, usually more than 60%. At present, the comprehensive utilization rate of iron ore tailings is low in China. Generally, the iron ore tailings are stockpiled in the tailings dam. The tailing dams not only occupy a lot of land, but also takes a lot of money to construct and maintain. In addition, the noxious substances in the tailings, such as residual flotation agents and heavy metals, have a severe impact on the ecological environment. There is little doubt that tailing dams have a visual impact on the environment due to their regular geometric shape. Iron tailings can be treated as compound mineral, which is an important component of comprehensive utilization of mineral resources, and is an has been widely concerned. Lots of scholars have done a large amount of research work on a large number of iron ore tailings. Since the iron mineral crystal grain size is fine and the iron grade is low, the iron tailings have failed to achieve good selection criteria."

Jan 1, 2018

By A. Gül

This investigation was carried out with low grade Murgul-Cakmakkaya copper ore once used to be dumped away as waste material. Sulphide minerals in the ore sample observed are chalcopyrite, pyrite, sphalerite and to some extent molibdenite; quartz, calcite and dolomite are the gangue minerals. The ore sample assays 0.28% Cu, 2.94% Fe and 3.36% S. Mineralogical study of the ore sample showed that adequate liberation of chalcopyrite for flota-tion was achieved below 100 µm. In flotation tests Aerophine 3418-A was the collector employed, NaOH or Ca(OH)2were the pH modifiers. Deactivators used were sodium meta bi-sulphide, starch, dextrin and lime. MIBC was the frother used throughout the tests. Test results showed that starch alone was the most suitable depressant to give the optimum metal content and recovery val-ues. Activated charcoal was used to adsorb excess collector species in the flotation pulp during cleaning stages After two stages cleaning of the rougher concentrate using starch as the depressant a copper concentrate assaying 21.2% Cu was obtained with 79.5% recovery while the tailings contained 0.01% Cu and metal losses were about 3%

Jan 1, 2014

By Teja Reddy, Narasimha Mangadoddy, Mandakini Padhi

"In mineral comminution circuits, the feed to hydrocyclone consists of a heterogeneous mixture having varied degrees of liberation and sizes leading to the multi-component particle system. The presence of multicomponent particles exhibits a significant change in the classification performance parameters. In this work, a numerical study is conducted with an artificial mixture of magnetite and silica of different proportions having similar particle size distribution to understand the multicomponent interaction in a laboratory scale hydrocyclone. The heterogeneous feed is injected tangentially would attain different settling rates under the influence of centrifugal, drag and turbulent dispersion forces. In this work, Large Eddy Simulation (LES) is used to resolve the continuous phase turbulence. Modified Algebraic Slip Mixture (ASM) model using the corrected Newtonian rheology of fines to simulate multi-density and multi-size particles of the mixture in a hydrocyclone. The influence of the multi-component particles on classification performance is extracted from the simulation in terms of the performance curve, i.e. recovery to underflow, volume fraction distribution and the key forces acting on each particle in the mixture. An interaction was observed between different components during the classification process, featuring accumulation of heavier particle at wall-side pushing the lighter particles into the inner locus of zero vertical velocity (LZVV) zone. The comparison of separation factors of different size particles presented the higher probability of the magnetite of same size reporting to wall region and hence to underflow. Hence, an increased component cut-size with the increased magnetite proportion, particularly a profound effect on lighter density component’s cut-size was observed. INTRODUCTION The multicomponent existence is found in naturally occurring ores, affecting the pure metal extraction, nonetheless also affects the comminution and classification processes. Among many another classifier, hydrocyclone is a vital equipment used vastly in many industries. The main advantages over other classifiers are a static body, low operating cost and maintenance, high throughput, low floor space requirement etc. A typical hydrocyclone consists of a cylindrical section with a central tube connected to a conical section with a discharge tube. The fluid is injected tangentially into hydrocyclone causes swirling and thus generates centrifugal force within the device. The multiphase interaction inside the hydrocyclone is extremely complex and mostly explained by theories based on hypothesis. In past years, many theoretical models were proposed like a balanced orbital model (Criner, 1950), the residence time model (Reitema, 1961) etc. Though these models give an estimation of the cut-size and other performance parameters, it cannot predict the accurate performance of the actual state of operation. Among these models, the balanced orbital theory is the most adapted concept, based on the force balances of the particle in the dual vortex flow of hydrocyclone. The finer particle is subjected to the inward drag force, generated from the outer vortex flow to the air core, and drags the particle towards the overflow. The larger particle with the higher mass have enhanced centrifugal force and falls into primary vortex near wall reporting to the underflow. Generally, the forces acting on the particle include the drag force, centrifugal force, pressure gradient force, added mass force, Saffman lift force, Magnus force and basset force (Kraipech, 2005). The major forces like a drag, centrifugal, pressure gradient are the function of the particle properties like the size and the density. Hence, the existence of the multi-size and the multi-density particle will affect the separation phenomenon, with the varied forces acting on it. The understanding of the multicomponent classification effect using ores has been only explored in few studi"

Jan 1, 2018

By Y. Tang

The paper studied the extraction characteristics of the fly ash from a location in Guizhou province. Under ordinary pressure, the fly ash is extracted by an acid and alkali, and then studied for its reaction characteristics with different extraction agentia, temperature, consistence and time. The results of acid extraction show that there are good reaction characteristics for Fe2O3 with HCl and the extraction rate decreases with the increasing of extraction time. There are good selective characteristics between Al2O3 and H2SO4 and they weaken with the increasing of temperature and the expanding of time. The best extraction results are shown with CaO and MgO because of their chemical characteristics and the over-saturation degree of the extraction processing. In addition, It?s found that it cannot leach all the substances from fly ash even with the higher consistence (10mol/L) of extraction agent, the longer extraction time (2h) and the higher temperature (100?) .It shows that the extraction rate of Fe2O3 is 82.81% and that of Al2O3 is 29.01%. The results of alkali extraction show that the extraction rate increases with the consistence of extraction agent and temperature, and the extraction rate of SiO2 by NaOH increases rapidly with the time expanding while that of Al2O3 falls gradually.

Jan 1, 2014

By Tracy Shimmield, Philip Samar

"Metals have been mined as ores since pre-history but metal production has increased dramatically in modern times driven by expanding Global GDP. Metal ore mining produces large amounts of waste rock and mine tailings. Mine tailings are the wastes produced after extracting the desired metal from the ore. There are several ways of dealing with this waste, and Ritcey (2005) identifies the following possibilities, land-based storage, backfill to the mine, deep lake disposal and marine disposal. In Papua New Guinea (PNG), both Misima and Lihir Mines adopted the marine disposal option, releasing tailings through a submerged pipe onto the sea floor. This special case is referred to as Deep Sea Tailings Placement (DSTP) in which the tailings deposition is sufficiently deep as to be below the euphotic zone. The most important aspect of deep sea tailings placement is that the tailings are deposited at great depth where exchanges between the seabed and the surface layers are small. The first quantitative multidisciplinary study of tailings impact on the deep sea was carried out from 2006 to 2010 in Papua New Guinea. The physical, chemical and biological work carried out has placed PNG at the forefront of research into the assessment and management of deep-sea environmental impacts related to mining in PNG. The study has provided data which has led to a better understanding of the ecological and geochemical processes in deep water that accompany DSTP in PNG and provided baseline data on deep-sea ecosystems in a scientifically poorly known tropical ocean. Additionally, guidelines on best practice for DSTP have been developed Here we present geochemical data obtained from sediment samples from the marine environment surrounding Lihir and Misima Islands."

Jan 1, 2014

By A. V. Bogdanovich

In diamond ores processing, final waste tailings size, rejected to dump, is one of the most important parameters. On one side, it is necessary to minimize losses of diamonds, whose size exceeds 1 mm, on the other side ? to provide for the plant high throughput and sufficiently low capital and energy costs, which is in greater part connected with disintegration process. Extensive laboratory, pilot-scale and commercial-scale dressability studies of different types of diamond ores have been performed at JSC ?Mekhanobr Engineering? in recent years. With that, special consideration was given to determination of the required ores? disintegration size that would provide for a high recovery of diamonds. In diamond ores processing, in order to exclude breaking of large diamonds, stage disintegration is used with regrinding of light fractions and heavy fraction X-ray fluorescent separation tailings. On account of rather weak bonds of diamonds with enclosing minerals, in crushing and grinding of diamond ores, selective disintegration takes place, with aggregates? breakup along plane surfaces of least bonding, which facilitates liberation of diamonds and their transition to free state. Heavy components losses with different sizes of final dump tailings were studied in processing of large samples. It was established, that in order to almost completely exclude losses of heavy components over 1 mm size, light fractions had to be ground to 2.5-3 mm size, while X-ray fluorescent separation heavy tailings of -15+3 mm size do not contain diamonds larger 1 mm in aggregates, and their regrinding does not increase total recovery of diamonds. On the basis of the conducted studies, relationships regarding heavy components and diamonds losses with respect to diamond ores final disintegration size were obtained, providing for more rational organization of the ores disintegration and processing flow sheet. Keywords: diamond, waste tailings size, disintegration process, recovery of diamonds

Sep 1, 2012

By Tong Guan, Guangqin Fu, Lihong Deng, Xiaotong Zhou

The raw ore contains many kinds of valuable metal elements. It is rich in valuable metal elements, such as Pb, Zn, Sb, Sn, Ag and is associated with S,Fe,As,In,Cd. A new technology which includes medium intensity magnetic separation, preferential lead flotation, zinc-sulfur bulk flotation, zinc-sulfur flotation separation, tin gravity separation and tin slime flotation was chosen to recover valuable minerals in the raw ore, and the iron concentrate, the lead concentrate, the zinc concentrate, the sulfur concentrate and the tin concentrate can be obtained. To the zinc-sulfur bulk concentrate with the grade of 7.21%Zn and 16.97%As acquired by the zinc-sulfur bulk flotation, two different flowsheets of Zn-S separation technology are chosen to study. The lab test shows that when using lime+DM as depressor, the zinc concentrate assaying 47.73%Zn with the recovery of 95.01% can be obtained and the test indexes are better than that of the flowsheet which using lime as depressor. At the same time, the Cd content is 0.65% and the In content is 0.10% in the zinc concentrate, so they all reach the smelting comprehensive recovery standards and the As content decreases to 0.23%. Finally the flotation separation of christophite and As-bearing sulfide minerals can be successfully realized.

Jan 1, 2014