Search Documents

By J. M. Pei

In this paper, the nonlinear finite element analysis is used to study the support system of a tunnel which is designed to pass through deep-embeded stratum. The rock mass is rather intact, though a section of tunnel will pass through the weak belt. Under the influence of the high ground stress, the condition of stability and the form of support become complicate. This paper, talcing into account the nonlinear properties of rock mass and the Interaction between rock, and support, makes a comparison between the two kinds of soft and rigid support systems, and analysed the changes of their bearing forces.

Jan 1, 2010

By Dr Karsten Galipp, Kai-Julian I. Hendler, Prof. Manuel G. Pinheiro, Dr Peter J. Bourne-Webb

With a share of approximately 11% of global greenhouse gas emissions, the construction industry contributes significantly towards climate change. This is why construction projects should not only be assessed on costs and technical solutions, but also on their carbon emissions. Life Cycle Assessment (LCA) is a tool which can quantify the environmental impacts of a construction project over its entire lifetime. The objective of this study was to determine the carbon footprint of three types of quay wall structures, namely sheet pile combi-walls, open piled decks and caissons using an LCA approach. Each of these quay walls were studied under the same boundary conditions, such as design life, ground conditions, dimensions, location and so on. The analysis showed that the sheet pile wall has the lowest carbon footprint whereas the open piled structure has the highest. Furthermore, it could be shown that the largest share of greenhouse gases (approximately 80%) is emitted during the production of construction materials. The transportation of materials and construction activities each contributed under 12% to total emissions. The sensitivity analysis showed that with innovative approaches, such as adapting the concrete mix design, the carbon footprint could be reduced by 26% to 40%.

May 1, 2022

By Larry Rayburn

Design of cost effective engineered solutions to complex problems requires the team efforts of the owner, the designer and the specialty construction contractor. The basic ingredients of success required to remain competitive and still produce a quality product are creative design based on experience and sound engineering principles, plus practical aspects of constructibility. The three case histories describe creative design/construct approaches that benefited all parties. 1. Introduction The increasing demand placed on specialty contractors to provide cost effective buildable solutions to complex construction problems compels us in the industry to be highly innovative. The practice of geotechnical engineering is considered more of an "art" than perhaps the other disciplines within civil engineering largely because of the basic nature and variability of soil and rock. The geotechnical design engineer must have the knowledge of the components of his design and know the limitations of his equipment and labor force. Thus, for the design/build specialty contractor the potential for creation of unusual solutions to difficult problems is quite high.

Jan 1, 1991

By Jacob Chacko

The Izmit Bay bridge, a 3-km-long suspension bridge crossing of Izmit Bay, Turkey is planned to be constructed in one of the most seismically active places in the world. The site, which has the potential to experience significant earthquakes associated with the relative motion accommodated on the North Anatolian Fault, is underlain by deep deposits of soft soils, and areas of unstable and liquefiable soils. Characterizing the seismotectonic setting, foundation soil conditions, potential fault locations, as well as other geohazards was a critical component for the project concessionaire to finance the project and obtain meaningful bids for bridge design and construction. Given the Build Operate Transfer (BOT) funding mechanism, executing this work in the least possible time was critical to the concessionaire?s financing scheme. Fugro was retained to provide geotechnical, geological, and seismological evaluations for the project region, and to generate data for contractors to develop reliable designs and bids. The uncertainties in these data made it difficult for the BOT concessionaire to finance the project and tender Bridge design and construction. The investment in an early and comprehensive site characterization program to evaluate and quantify those uncertainties allowed the concessionaire to save schedule, provide a robust bid basis to bridge contractors, and persuade banks to finance what was perceived to be a relatively high risk project.

Jan 1, 2011

By Wolfgang G. Brunner

The center of Berlin is currently a huge jobsite, where international architects, designers, consultants, construction and ground engineers as well as investors take on the challenge of the biggest and probably most complicated projects in terms of soil conditions in Europe. The Berlin sand is generally suitable for foundation measures, but can be very tricky in deep excavation pits below the high ground water level. The reason for this is its uniform grading, medium dense stratification and lack of cohesion. The requirements for these deep pits are: - measurements in the range of up to 120 000 m2 per pit - depths up to 19 m below ground water level - lack of dense horizontal geological layers - no permission for lowering ground water levels - toughest ever European competition in construction. Sheet pile walls, sheet piles set into cut - off walls, secant pile walls, diaphragm walls, all with tie backs under high water pressure, are used as retaining sytems. The pits are closed at the bottom against water either by under water concrete, deep lying grouted cut - offs or high lying jet - grouted cut - off slabs. The huge dimensions of these excavation pits are a new challenge for ground engineers, and new technology had to solve the upcoming problems and resulted in new experience.

Jan 1, 1999

By Jamie D. McEwan

To cater for the future introduction of 12 car trains, London Blackfriars railway station is being extended from the north end to span across the River Thames. Following the demolition of existing buildings, a number of challenges had to be overcome including working adjacent to a live railway line, above live London Underground tracks and working in small restricted spaces. Trains entering and exiting two lines of track at the bridge's north end of track meant that access was difficult due to the location and proximity to existing infrastructure. The site was very much constrained and congested and there were also a series of works in place to maintain passenger flows so as not to inconvenience the travelling public. The site had been developed many times in the past resulting in a number of obstructions that would require removal during the piling work including old brickwork, reinforced concrete, redundant railway sleepers and track and existing concrete and timber piles. A number of solutions had to be devised to overcome these obstructions. Piling works were undertaken during the day and at night to meet programme.

Jan 1, 2011

By Maurizio Siepi, Fabio Santillan, Lyndon Bedford, Carlo Crippa

"Abstract: Wolf Creek dam, on the Cumberland River in Kentucky, US, operated and maintained by the Nashville District of the USACE, is the Corps' largest reservoir east of the Mississippi river. The 1748 m (5,736 ft) long Wolf Creek dam combines earthfill and concrete gravity sections. Construction began in 1941 and was completed in 1950. The dam showed signs of instability in the 1960’s, and in the late 70’s an in-depth project of rehabilitation was undertaken, using both grouting and secant piles. The works saved the dam, but in the late 90’s further signs of distress worried the Nashville district of USACE which, after a study conducted on the water seepage, concluded that construction of a new concrete barrier cut-off wall was needed. In 2009, the $341.4 USD million contract was awarded to TREVIICOS-SOLETANCHE JV.The new wall, located upstream of the concrete monoliths, has a minimum thickness of 60 cm (24 in.), and runs the length of the embankment, into the right abutment, for about 4,200 feet. The founding depth reaches 84 m (275 feet), well below the zone of solutioning. With a total surface approaching 92,903 sq.m (1,000,000 sq.ft), the Wolf Creek barrier wall is unlike any other project in the world.The construction of the cut-off wall followed a complicated but logical sequence of several operations, involving a variety of technologies: grouting, hydromill, directional drilling, and secant piles with reverse circulation. The intensive rock grouting program was aimed to minimize the risk of slurry loss and extend the positive cut-off further deep. Subsequently, an Encasement Concrete wall was installed with hydromill, toeing into the rock, to protect the embankment during the following phases. Smart holes were then drilled into the Encasement wall down to the final depth. Eventually, the holes were used to install the secant piles by employing the reverse circulation piling method.An extensive verification campaign has confirmed the superior quality of the cutoff wall consisting of 1200 secant piles, exceeding by far USACE’s requirements. The main project was substantially completed in early 2013. A small portion of secant piles wall will be installed downstream of the dam, to close the switchyard, finishing the project in the early months of 2014.IntroductionWolf Creek Dam is located on the Cumberland River in south-central Kentucky. The Nashville District of USACE operates this multipurpose dam to provide hydropower, flood control, water supply, and water quality benefits for the Cumberland River system and surrounding region. Lake Cumberland, created by the dam, impounds 7,400 million cu.m (6 million acre foot) at its maximum pool elevation of 232 m (760 ft) above sea level. This lake is the largest reservoir east of the Mississippi and the ninth largest in the United States, and attracts 4.89 million visitors, more than Yellowstone National Park (2.87 million).This paper describes the recently completed works for the rehabilitation of the dam, accomplished by TreviICOS-Soletanche JV with the construction of a new Barrier Wall."

Jan 1, 2014

By N. C. Matheson

The West's Shell Pile has been used on sites with very soft ground conditions for over 60 years. Fibre reinforced precast concrete shells 900mm long are threadled onto an internal mandrel which can be extended according to the depth driven to attain the load bearing resistance. On completion of driving the mandrel is removed leaving the precast shells to form a permanent lining to the cast insitu concrete core. To give resistance to high contamination, a tar based epoxy coat is sprayed on the outside of the shells or a flexible PVC liner is installed inside the shells to protect the core. Fundamental to the resistance to contamination is the quality of the precast fibre reinforced concrete shell, the mix design and method of manufacture. A series of detailed laboratory experiments were carried out using samples immersed in concentrated acid and sulphate solution. The long term effects of exposure to contamination is recorded in the case studies of existing piles at two gasworks sites.

Jan 1, 1989

By W. J. Kingwell

My comments and questions are addressed to Mr. Troughton. It seems to me that the tests were very well tailored to determine long term effects on performance of bearing piles as groundwater pressures rise in the London Basin. This rise is being simulated by means of a groundwater recharge system but it would be informative to have further details of the controls of conditions simulated. Ideally the porewater pressure in Standpipes 1, 2 and 3 should be the same throughout the test. Under test conditions are there not practical dif­ficulties? Recharge Well C2 is a lesser dis­tance from the pile than the other wells. Was the rate of recharge to C2 regulated to a lesser rate than the other three? In my experience the rate of acceptance usually varies from well to well. Under a common feed pressure were mea­sures taken to compensate for this? Since the problem does not only affect London, but also Liverpool, Nottingham, Birmingham and to a lesser extent, Manchester, I question whether an ideal procedure is being used. It is well known that rates of acceptance decrease with time and often recharge wells need to be flushed out at regular intervals. Other pro­cedures may need to be adopted to accurately simulate the effect of groundwater rise, if tests of longer duration are to be considered.

Jan 1, 1991

By L. F. Albert

The paper describes solutions given to foundation problems during the reconstruction of a power plant set on fire, located adjacent to several still Working Units. After a detailed site and laboratory investigation, it was decided that it could be possible to include within the new foundations the preexisting cast in situ driven piles with enlarged base 50 cm in diameter and let them work with new 41 cm driven, cast in situ piles without enlarged base. Demolition of existing caps was carried out with expansive mortar in order to avoid any possible damage to piles, whose actual conditions were checked by several load tests. New piles were designed to support service load by shaft resistance, in order to limit total and differential settlement. When piles had to be driven adjacent to nearby structures, measurements of peak soil particles velocity were carried out while driving piles at decreasing distance from critical locations. By preboring most of the upper clay layer it was possible to reduce within safe limits for structures the induced vibrations.

Jan 1, 1989

By Harpal Parmar

This paper evaluates dynamic methods of pile capacity prediction by comparing their results to static load test results. Dynamic and static pile load test data were assembled from four southeastern states of the U.S. End-of-drive and restrike capacities were evaluated using the Pile Driving Analyzer (PDA) and by wave equation (WEAP) analyses. These were compared to static (Davisson criterion) loads. The best comparison was obtained for restrike PDA results; restrike wave equation analyses values also compared well. The end-of-drive results for both methods-showed relatively poor comparisons. The PDA was recognized as an important tool to measure energy transferred to the pile; this transferred energy was recognized as an uncertainty when conducting wave equation analyses. A statistical analysis showed restrike capacity results to be associated with higher precision and accuracy as compared to end-of-drive methods. The authors believe that restrike dynamic testing is essential to establish long term static soil strength and that it will lead to accurate and cost-effective design of piles.

Jan 1, 1996

By Shaw-Shong Liew

This paper presents the design concept using floating piles to support 2500Ton oil storage tanks on a very soft alluvial clayey soil of about 40m thick in Riau Province of Sumatra, Indonesia. The floating piles of various penetration lengths were designed to support seven numbers of such storage tanks seating on a 20m diameter and 500mm thick reinforced concrete (RC) circular raft. The pile points have been strategically located at the RC raft. Varying pile penetration lengths have been designed to minimize the angular distortion of the thin RC raft and the out-of-plane deflection at the tank edge. Vibrating wire strain gauges were installed at different levels inside the ø350mm prestressed reinforced concrete piles to measure the load transfer profile during the static load tests and water-loading test. The installation and interpretation of the instrumentation are described and discussed. Boreholes, in-situ tests like piezocones, vane shear tests and standard penetration tests, and laboratory testing were carried out to obtain geotechnical parameters for the pile designs. Static load tests were also carried out on the spun piles of varying lengths of 24m, 30m and 36m respectively. It has been demonstrated that the floating pile system can be a cost effective design to support heavy structures on very soft compressible deposits with satisfactory performance. Finally, the design concept validated with the results of instrumentation is discussed.

Jan 1, 2002

By Emöke Imre

A point-symmetrical linear coupled consolidation model with displacement boundary condition is suggested for the description of the consolidation around the pile tip after pile penetration. Analytical solution is given. Main features of the solutions are predicted by the analysis of the system of differential equations and, the boundary conditions.

Jan 1, 2002

Port Gaspé is located on the back side of Gaspé bay and is protected by a natural sand barrier with a length of 2,5 km, from which it got its name, Gaspé Sandy Beach (1). Since 1904 the Gaspé region had a deep water wharf, initially very different, in fact, from the one existing just before the recent reconstruction (2). This wharf with a length of 228 m and a width of 23 m was build of timber cribs. The outside walls of these cribs had been doubled with a wooden wall, creosote impregnated to provide resistance to decay and to the attack of marine organisms (limnorias) (3). Fifteen years ago the upper part of the wood construction had to be removed, because of progressing rottenness and was replaced by an L-shaped reinforced concrete structure (4).

Jan 1, 1987

By Michael Arnold, Jonathan Delgado

In 2017, Bauer Foundation Corp. (BFC) was awarded the contract to install the deep foundations for the new 17-story Hotel Tower and the Low Rise Casino Expansion at the Seminole Hard Rock Hotel and Casino in Tampa, Florida. The site was underlain by extremely challenging Florida Limestone geology and surrounded by occupied existing buildings and infrastructure. To overcome the challenges of the difficult subsurface conditions, and to successfully complete the foundation installation without impact to the surrounding buildings and casino operation, Langan Engineering (EOR) and BFC were required to modify both the design and installation techniques during construction. The scope of work included 147 temporarily cased drilled shafts to depths up to 230 ft (70 m) below ground surface (BGS), 76 permanently cased micropiles up to 200 ft (61 m) BGS, and more than 300 augered-cast-in-place (ACIP) piles up to 125 ft (38 m) BGS. Voids and zones of high permeability in the limestone created many challenges for execution of the foundation scope including ACIP piles overbreaks of more than 400% above neatline volume, and construction induced ground subsidence/collapses adjacent to structures supported on shallow foundations. This paper will discuss site limitations, design and construction challenges, difficult geology, varied soil conditions, and lessons learned. PROJECT The project is located at Seminole Hard Rock Hotel and Casino Tampa, Florida, as shown in Fig. 1. Seminole Tribe, the owner, started the construction of a new 17-story Hotel Tower and the Low-Rise Casino Expansion at the beginning of 2017.

Jan 1, 2018

By Juan J. Campo

The Freeport-McMoRan Main Pass Mine development in the Gulf of Mexico is a complex designed to extract up to 67 million long tons of sulphur over a 40 year period. The initial development includes 15 platforms and 13 bridges located in water depths ranging from 208 to 214 feet, approximately 15 miles east of the Mississippi River Delta. Three additional platforms were designed and installed for the oil and gas development in the complex. Over 110, 000 short tons of steel were required to fabricate the structures. As the sulphur is extracted significant subsidence is predicted over a major portion of complex in the shape of a very large bowl. Vertical elevations are predicted to change as much as 65 feet. Horizontal movements and mudline slope changes cause adjacent platform decks to move as much as 30 feet relative to each other. Differential soil movement is predicted between piling of individual platforms causing the piling to spread, resulting in significant lateral loading on the piling. Relative vertical soil movements are predicted along the lengths of the piles which causes "up drag" or "down drag" forces on individual piles. This paper addresses the design of the piling for the structures in the complex. Design criteria will be discussed explaining how the more traditional offshore environmental and gravity loadings were combined with the unique loading caused by subsidence. Design and analysis procedures will be explained and analysis results presented. These results include the incorporation of 100 ksi steel in thicknesses up to 5 inches in some of the tubular piles. Comparisons will be made between conventional offshore structures and these structures designed to accommodate the subsidence.

Jan 1, 1992

By Dean E. Harris

The realignment of U.S. Highway 95 in Sandpoint, Idaho, is being designed on a site underlain by glaciolacustrine soil that includes very thick deposits of soft, sensitive clay to estimated depths of greater than 200 m. The highway realignment will include construction of numerous embankments, mechanically stabilized earth (MSE) retaining walls, and pile-supported bridges. The area of the proposed new highway corridor also includes existing historic and commercial buildings, a railroad, sensitive environmental areas, and economically vital tourism/recreational assets. The evaluation of pile axial capacity included the use of a variety of methods, including total stress, effective stress, and empirical methods using the results of piezocone soundings and conventional borehole and laboratory tests. These methods were used along with the findings from an instrumented static loading test to design the piled foundations for the bridges. A critical factor throughout the design of the pile foundations was controlling settlements to levels that could be tolerated by the bridges. Also, because of the proximity of the pile foundations to the existing structures and the proposed new embankments, the project has required careful consideration of the potential interaction between these elements. The analysis of piles also considered the potential for settlement of embankments, drag loads on the piles, and downdrag.

Jan 1, 2003

By Li Huimin

In this paper the step of determining the property index and the program of mixture ratio design of stabilizing agent in deep foundation construction are presented. According to the principle of computer simulation, the model and the method of computer simulation for optimum mix design are set up. Also, the precision of simulation results has been estimated and verified experimentally.

Jan 1, 1991

By K. Y. C. Chung

A case study on foundation engineering through organic soils is presented. Located along the west shore of the Hudson River, site soils consist of random brick fill over a thick layer of peat and organic silts or clays. The organic layer is underlain by medium dense to dense sand with varying amounts of silt. Strong artesian pressures were measured in the sand. A pile foundation system was selected to support all structures. To avoid periodic flooding, new fill must be placed on the existing fill. Large total and differential settlements will occur due to consolidation and secondary compression of the organic soils. This settlement will reduce the allowable pile capacity due to the large negative skin friction in the organic layer; and will necessitate long-term maintenance of the final grade elevation. Pile load tests were performed to determine the allowable compression and uplift capacities, long-term capacities and pile driving criteria.

Jan 1, 2010

By K. Rainer Massarsch, Bengt H. Fellenius

"Abstract Vibration limits for buildings with respect to ground vibrations from pile driving published in international standards are reviewed. At first, relevant vibration parameters are defined and the evaluation of vibration records is described. The sensitivity of structures to different vibration parameters (displacement, velocity and acceleration) is discussed. Most vibration standards relate to blasting activities, the dynamic characteristics of which can be significantly different to those from construction activities and in particular, pile driving. Several vibration standards are reviewed. The Swedish vibration standard is described in detail, as it is the only one accounting for several important factors, such as ground conditions, building material, and type of building foundation. Many standards limit the guidance to values based on the dominant vibration frequency and a wide scatter of frequency-dependent vibration limits exists. It is difficult to compare limiting values of ground vibrations proposed in different standards.1. INTRODUCTIONFor poor ground conditions, placing structures on piles is the most common foundation solution, while sheet piles are widely used to support deep excavations. Piles and sheet piles must often be installed in the close vicinity to buildings, structures or installations in the ground, which can be affected by ground movements and vibrations, (Massarsch and Fellenius, 2014). In many areas, environmental concerns with respect to noise and ground vibrations can restrict or even prohibit driving of piles or sheet piles or reduce the efficiency of installation. The design engineer must prescribe – often at an early stage of a project — the permissible levels of ground vibrations in order to minimize the potential risk of building damage. When seeking guidance from the literature, little or practically no applicable information can be found on how to assess permissible levels of ground vibrations."

Jan 1, 2014