Search Documents

By P. Srinivasulu

The popular theoretical models used for assessing the dynamic behaviour of piles under vertical and lateral excitations are critically reviewed. An experimental study is presented on model piles with varying slenderness ratios. The theoretically evaluated and experimentally deduced natural frequencies and resonant amplitudes of the test pile-soil system are compared. The dynamic stiffness and damping are seen to increase with increasing slenderness of piles. Further, the damping yielded by the theory is found to be on the unconservative side.

Jan 1, 1996

By Kyle M. Rollins

To improve our understanding of lateral resistance of pile groups, a series of lateral load tests were performed on a full-scale pile group using both static and dynamic loads. The pile group consisted of nine 0.6 m-diameter steel pipe piles driven into clay. During the static tests, the load was cycled fifteen times to evaluate the drop in lateral resistance that would occur due to repeated loading and the formation of a gap. The peak load typically decreased by about 15% from the initial cycle to the last cycle. The load carried by each pile was also measured and there was a significant drop in resistance for the piles in the trailing row relative to the leading row. The dynamic force was applied using the Statnamic loading system which produced a lateral force of 3500 kN (787 kips) in about 0.1 seconds. In two cases, dynamic loads were applied following application of 15 static load cycles. In these cases, the dynamic lateral resistance was about the same as the static resistance, likely due to gaps around the pile. In three other cases, the dynamic force was applied prior to the cyclic loading. In these cases, the dynamic resistance was 30 to 60% higher than the static resistance. Simplified analyses suggest that the difference in resistance could be attributed to damping produced by the soil surrounding the piles during the virgin loading.

Jan 1, 2002

By M. Y. Xia

In this paper, based on the Theological tests of the interface between clay and concrete, an interface Theological model is proposed and is used in the finite element analysis which takes soil as viscoelastic mass and Theological effect of the interface between diaphram wall and ground into consideration. Its results are compared with those without an interface element, without considering the relative creep displacement. Close attention is paid to the variation of wall with time under the condition of various interface shear stiffness and viscous sliding coefficient, and their effects on the wall bending moment are primarily verified in the paper. The change of wall bending moment with time, trench heave and wall displacement in different excavation depth, bracing position, parameters for soil are also studied.

Jan 1, 2010

By L. J. Whitworth

Five trial piles were constructed during the trial pile programme for the Birmingham International Convention Centre. In addition, trial piles have been tested on two other sites in central Birmingham. Methods of pile construction were conventional sandstone rock sockets, sleeved piles and voided piles. The results of these load tests are compared with the theoretical predicted behaviour based on the results of unconfined compressive tests of rock core taken on the Convention Centre site and on other sites in the central Birmingham area. On the basis of this work, the various design procedures are discussed.

Jan 1, 1989

By H. R. Shen

Cushion materials are one of the most important links in an efficient piling system. In the past, little has been done in China on this problem, so engineers are still used to those traditional woods, papers and coir ropes. In this paper, the SOA of piling cushions, their testing method and parameters used in wave equation analysis for piling are briefly reviewed. The static and dynamic mechanical characteristics of 3 types of cushion material have been determined in laboratory and suggestions about testing method and evaluation of test results are given.

Jan 1, 2010

By Jack Hayes

Vibrating wire strain gages have proven to be a very reliable and effective tool for the measurement of strains associated with the loading of bored piles (drilled shafts). However, when these strains are used to calculate the load, or stresses in the pile, the results can sometimes be confusing and/or difficult to interpret. This paper describes some of these situations, using examples from actual case histories, and discusses some of the difficulties associated with residual load effects, curing and temperature induced strains, load stress distribution effects, estimated modulus and area.

Jan 1, 2002

By K. Oshima

In Japan, earthquakes are experienced frequently. Many buildings and structures in Japan are supported on pile foundations. For these pile foundations, the joint section between the piles and footing (hereinafter referred to as "Pile Head Joint"), where the load of the superstructure is transmitted to the ground through the piles, is important in both the design and construction of works particularly under seismic conditions. This paper discusses the state in which the force is transmitted to the Pile Head Joint, and introduces the basic construction of the Pile Head Joint, based on experimental investigation. Steel pipe piles

Jan 1, 2010

By W. G. K. Fleming

The codification of foundation design and construction is a subject of extensive discussion in Europe and all current code proposals are based on limit state partial factoring. For simplicity, it is claimed, simplified forms of Partial Factor use are presently being advocated but, if this is the direction which codes are to follow, then it is preferable in this age of computer technology that a true system should be adopted rather than a simplification. A philosophically satisfactory method can readily be found which can fulfilcurrent requirements and it is better that such a method should be adopted from the beginning rather than later to find it necessary to make important alterations and amendments.

Jan 1, 1996

By Safwan Labanieh

An experimental set-up is specially designed to study the behavior of a friction pile of 3 cm diameter in contact with the soft clay of Mexico City in a small calibration chamber (CC) of 30 cm diameter and 50 cm height. The consolidation of this compressible clay is accomplished using a special system adapted to the CC itself to insure a good knowledge of the initial state. Loading results of the pile under a consolidation pressure of 50 kPa indicate an elastic mobilization of shear stresses at the shaft of the pile (?3 kPa for 1mm displacement) followed by a hardening plastic type behavior. Unloading-reloading results indicate a mobilization of shear stresses of the same type and of the same order of values obtained from the virgin loading stress path. Cyclic loading (?40 cycles) between 0 and 1 kPa (1/3 of the failure value) give similar results to those obtained from virgin loading.

Jan 1, 2002

By Emad Farouz

This paper compares the predicted axial capacity of driven Pre-cast Pre-stressed Concrete (PPC) piles for the Lake Gaston Water Treatment Plant (LGWTP) using several design methodologies versus the axial capacity measured from dynamic and static load testing. The LGWTP site is located in Chesapeake, Virginia and is part of the Great Dismal Swamp. The subsurface investigation included soil borings, in-situ dilatometer (DMT) tests, and in-situ piezocone (CPTu) tests. The axial capacity predictions of the PPC piles were performed using the computer programs DRIVEN and FB-DEEP which are based on SPT N-values. Additionally, an empirical method proposed by Martin, et al. (1987) based on local experience with PPC pile design in the Yorktown formation in the Tidewater area of Virginia was also evaluated. Finally, the ?Laboratoire Central des Ponts et Chausées (LCPC)? method developed by Bustamante and Gianeselli (1982) based on CPT measurements was also used to develop the axial pile capacity of the piles. This paper shows that the FB-DEEP computer program and the LCPC method provided a reasonably good prediction of the pile axial capacity measured from PDA, CAPWAP, and Static Load Tests in comparison with the other design methods used. The soils in this area develop significant setup over time and it was found that FB-DEEP and the LCPC method are capable of incorporating this setup in the prediction of the long-term axial capacity of driven piles in this area.

Jan 1, 2007

By Yong Jingrong

Based on the results of several test socketed piles in Sichuan, the mechanism of the deformation for a loaded socketed piles is investigated, and the concept of the socketed effect is proposed. The bearing capacity and settlement of socketed pile are controlled directly by socketed effect, that is an important mark different from the other types of cast-in-situ piles. According to the analysis of this effect and factors interferring it, their roles are discussed with the results of test piles. In order to increase the bearing capacity of piles, the ways and methods enhancing socketed effect are recommended.

Jan 1, 1991

By RAP Bement

Installation by vibrodrivers of sheet and bearing piles generates periodic vibrations in the surrounding ground, which have been widely measured and reported. One of the possible consequential effects of these vibrations is ground settlement caused by the compaction of loose granular soils. Vibratory compaction settlement of a range of granular soils has been studied in the laboratory using a 150mm diameter Rowe cell, which allows sample preparation and control during vibrations equivalent to conditions in the field during vibrodriving. The cell containing the soil sample was mounted on an electromagnetic shaker and vibrated at amplitudes and frequencies appropriate for soils adjacent to vibrodrivers. The changes in sample height were recorded.

Jan 1, 1996

By John R. Davie

This paper describes the design and construction of two 5.6 MN capacity drilled piers installed to support the main loading elements of a large cantilevered gantry crane. The critical crane columns were located within and at the edge of an existing sheet-pile cofferdam, which had been filled with loose coal slag when it was originally constructed Due to the presence of the slag and the age and questionable condition of the sheet-piles, the drilled piers were installed to provide vertical and lateral supports for these columns. The lateral capacity of the piers was supplemented by two smaller drilled piers and two large spread footings that were linked by a system of grade beams.

Jan 1, 2006

By Rob van Dorp

Most traditional foundation designs are based on soil investigations using Standard Penetration Testing (SPT), sometimes combined with static load testing on sacrificial trial piles. However, this design approach has two major shortcomings. First, SPT data do not provide direct and continuous informa- tion about soil resistance as a function of depth. Second and more important, because of the relatively wide spacing between borehole locations, SPT soil investigations do not provide adequate information about variability of soil profile and/or soil resistance over the project area. Preliminary pile load testing on an SPT location can compen- sate for the first disadvantage but cannot address the second disadvantage. A design approach based on an adequate soil investigation campaign with Cone

May 1, 2022

By S. L. Karunakaran

There are cases where it is found that a raft foundation would have adequate factor of safety against ultimate bearing capacity failure but the settlements would be excessive. Piles may be introduced in order to limit settlements to an acceptable level. The actual number of piles required to reduce the settlements to an acceptable level may be very small compared to the number of piles required to transmit the whole structure load. The paper focuses on the difficulties encountered in evaluating the load sharing between raft and piles. An elaborate analysis taking into account the interaction between raft, piles and soil is very complex and time consuming. Few approximate methods for arriving at a satisfactory solution to piled raft system are discussed in the present paper.

Jan 1, 1996

By Subhash B. Bhide

Deep foundations are affected by the presence of sulphates, chlorides, organic contents and water currents present in the soil. The sulphates in soil and ground water interfere first with setting of concrete. In long term, growing of sulphate crystals in concrete, crevices can spall the concrete. The chlorides mainly affect the steel. The organic content does not allow the concrete to set. It also reduces the compressive strength of concrete. The frequency and methods of sampling and testing for above corrosive elements are discussed. Presently available methods to avoid attack due to these corrosive elements are discussed. The stipulations by various codes are summarised. A method to assess the short term impact is elaborated with results of field studies. A tool developed to study the presence and effects of underground water currents on concrete is also discussed.

Jan 1, 1996

By Shamsher Prakash

Estimation of vertical load carrying capacity of a single vertical pile under earthquake loading is an important task of a design engineer. Lateral vibration of vertical pile is highly influenced by the magnitude of vertical load. Several load reversal, during earthquake loading introduce gap between pile soil interface which reduces its load carrying capacity and increases lateral motion. This paper presents a simple time domain numerical scheme to estimate the lateral pile response, considering the loss of contact of pile at pile soil interface, during impact and earthquake loading. The motion of the pile is limited in the vertical plane. Time domain has been discretised into small intervals. The non linearity of soil properties has been taken into account by discretised Winklers model with Wolfes frequency independent mass spring dash pot coefficient for geometric damping. Suitable software has been developed which keeps track of the load reversal point of each elements.

Jan 1, 1996

By J. S. Ward

In a well-written set of contract documents, the probability of conflicts arising during the course of construction is minimized. However, no matter how complete may be the technical language in the contract plans and specifications, the possibility always exists that conditions may be found in the field that were not anticipated at the time the design was formulated. In foundation engineering work, this is commonly referred to as "differing site conditions." When such a conflict arises in the field, the most expedient manner of resolution would be for the parties to the contract to meet and to amicably resolve the issues rather than use the long and costly adversarial approach of the litigation system currently prevalent in the United States. This rapid solution to the construction conflict can be accomplished through an alternate dispute resolution technique that includes mandatory discussion, mediation and arbitration to be initiated immediately following the inception of the dispute and to be concluded in not more than 100 calendar days from the time the dispute originated.

Jan 1, 2010

By Ashley Shirer

Have you heard a geotechnical engineer rail against using the word "dirt"? The typical maxim is: "It's not dirt, it's soil!" This axiom is so prevalent that it is joked about on the construction site. How did we get to the point in our profession that soil is too technical to understand, while dirt is not viewed as important? Take a moment and think about the images that come to mind by the word soil. Responses range from the sand at a playground to the mud that sticks to the bottom of your shoe, the dark loam found in gardens to the firm earth under your feet. But do you know where the term soil originated? Or how it was intended to be used? This article looks at how word choice can lead to very different motivations for owners, designers and constructors.

May 1, 2023

By Matt Sotirin

The Santa Fe train station and passenger rail platform were constructed in the downtown district of Fort Madison, Iowa, over a century ago. This landmark building and rail platform were in need of major renovations and rehabilitation in order to restore the site to a functioning railway train station. A multitude of key players from various public and private parties were involved in the design and construction of this project site. Part of the project consisted of constructing the passenger platform. The original design included helical piles to provide foundational support for the platform. Challenges occurred during construction due to the presence of an obstruction in the form of a poured concrete slab in the immediate area where the helical piles were to be installed. The contractor worked with the engineer of record and other consulting parties to value engineer the helical pile design and utilize self- drilling micropiles as a replacement to the specified helical pile system.

Oct 1, 2022