Search Documents

By Fabiola Alvarez, Ana E. Bote, Daniel Pasquevich

"The oxidation of aluminum and its alloys was extensively studied for improving the corrosion resistance in structural materials having high specific strengths. But this reaction involves the formation of a very thin barrier layer on the metallic pieces. Furthermore, the ·recent development of the directed melt oxidation process for producing metal-ceramic; composites has renewed the interest in the study of interaction between gases and metals. Oxidation experiments in the presence of different chlorine partial pressures and at different temperatures were performed in ·a thermogravimetric balance, and microstructures were analyzed by electronic microscopy and X-ray diffraction. The oxy-chlorination kinetics was determined and the oxide formed W(IS amorphous at temperatures below 600 °C and crystalline .at higher temperatures. The appropriate experimental conditions for the fastest completed oxidation was further determined.IntroductionThe use of fine powders for the manufacture of ceramic components has significant advantages. They include excellent sinterability; low sintering temperature and better microstructure leading to improved mechanical properties. The conventional method of producing fine oxide powders involves controlled precipitation and pirolysis of suitable salts. The main limitation of the high temperature decomposition route is the evolution of environmentally unacceptable and corrosive gases. Controlled precipitation of hydroxides from solutions of salts, followed by thermal treatment involves large volumes of solutions and the calcination step that can induce grain growth (1).Direct oxidation of aluminum metal for producing alumina powder requires high temperatures for the direct oxidation of molten Al alloys by a vapor phase oxidant process (2, 3) or high technological process like thermal plasma reactor ( 4).Oxidation of high purity aluminum (5, 6) below the melting temperature· is initially characterized by a nearly linear reaction rate, followed by a rate which decreases rapidly with further weight gain. However, the oxidation rate of an aluminummagnesium alloy is much faster and it does not conform to any common oxidation law, but it is nearly parabolic at temperatures between 200 and 400 °C, an nearly linear· above 400 °C."

Jan 1, 2000

By Y. Yang, S. Peelman, J. Sietsma, Z. H. I. Sun

The rare earth elements (REEs) present in the Kiruna iron ore mine tailings are being considered as a new REE resource for the EU. These tailings, after beneficiation, contain approximately 5000 ppm of rare earths, concentrated in apatite and monazite minerals. To economically extract the REEs from these tailings the phosphorous contained within the apatite must also be extracted and the waste production of the process should be minimal. To achieve the extraction of REEs and phosphorous HCl and HNO3 were investigated as possible leaching agents. Based on the results a leaching process using HNO3 is proposed. This process produces H3PO4 from the apatite while simultaneously dissolving the REEs. The resulting leach liquor is then cooled to remove the unwanted Ca as Ca(NO3)2. Analysis of the leach liquor reveals extraction ratios of between 75% and 100% for the heavy REE (e.g. Y, Eu, Dy, …) and below 40% from the light REEs (i.e. Ce, La). Full phosphorous extraction was also achieved.

Jan 1, 2016

By R. E. Sundell, S. M. Correa

"A mathematical model is developed for the fluid flow in tungsten-inert gas weld pools. The fluid is taken to be incompressible, viscous, electrically conducting, and confined within a pool of specified shape. The flow is driven by surface-tension gradient (thermocapillary), electromagnetic, and buoyancy forces generally in this order of importance. Analysis indicates that the electromagnetic field may be calculated a priori and so decoupled from the nonlinear fluid mechanics and heat-transfer problem. The resulting set of equations is solved numerically by a line relaxation process. Computational errors caused by truncation in finite-difference schemes and by inadequate grid distributions are considered. The model is used to study several cases of differing heat and current input to the pool with and without surfactant-induced thermocapillary forces. The principal conclusions are that the thermocapillary flow, when present, is dominant with surface velocities on the order of 1 m/s. The heat transfer, as deduced from isotherms within the pool, is crucially dependent on the flow. Also, flow velocities and weld-pool surface temperatures were measuredand agree well with the model.2. IntroductionThe requirements of improved control and of automation in the TIG (tungsten-inert gas) welding process have led to the development of mathematical models for the heat transfer to the workpiece. It is now widely recognized that the fluid flow in weld pools sufficiently distorts the conduction heat transfer pattern to warrant inclusion in a process model. The experiments of Woods and Milner (1), among others, demonstrated that TIG weld pools could be driven by the electromagnetic J x B body forces present, J being the current distribution and B the induced magnetic field. Atthey (2) calculated that in typical pools the buoyancy force was about an order of magnitude less important - despite the large temperature gradients present - and neglected it in a computational study of the magnetohydrodynamic (MHD) flow. This work also reviewed many earlier studies of MHD flow caused by a source of current at a fluid surface, including analytical studies by Shercliffe (3), Sozou (4), and Sozou and Pickering (5), and a numerical study by Andrews and Craine (6). These works establish the importance of the electromagnetic force in the weld-pool flow."

Jan 1, 1986

By Gang Qi

The solubility of nitrogen in pure molybdenum was measured over the temperature range 2173 to 2473 K and up to one atmosphere (101 kPa) of nitrogen gas pressure. Both thermochemical and kinetic aspects of this phenomenon were considered in this study. The solution of nitrogen in molybdenum may be expressed by the reaction 1/2N2(g) = {N} (Mo,s), for which the standard Gibbs energy is given by the expression {A}G° = 78,500 + 27.36T Joules/g atom N. The formation of molybdenum nitrides, specifically Mo2N, was considered. Attention was also focused on the mechanism of nitrogen solution in molybdenum. Estimates of the diffusivity of nitrogen atoms in solid molybdenum were derived from the kinetic data.

Jan 1, 1991

By Jason H. Nadler, Jason A. Kulpe, Stephanie J. Lin

"A numerical method has been developed to predict the microstructural characteristics of reticulated metal foam. The porosity of this foam is derived from sacrificial template particles of known particle size distribution, which are incorporated with other precursor components. In this approach, a porous structure is numerically generated starting with Powell's sphere packing algorithm. The resulting stochastic structure has characteristics similar to those of corresponding metal foam. Deterministic inter-sphere connections are calculated to more accurately model the pore morphology that evolves during thermochemical synthesis. Estimations of pore morphology and specific surface area of the simulated material are compared to lab-synthesized materials composed of equivalent constituent compositions. In addition, the effect of template particle size, inter-sphere connections, and the geometric constraints on pore morphology and permeability are investigated to refine microstructural evolution and design.IntroductionReticulated foams, characterized by their interconnected pore network, can be obtained by incorporating spherical sacrificial template particles into precursor materials followed by template removal processes. The resulting structure is composed of contiguous spherical pores whose morphologies reflect those of the original templates. Based on some of the unique features of this synthesis approach, a methodology is introduced in this work whereby these foams are digitally constructed using experimental data from the template particle sizes and precursor formulation. Digitally constructed porous structures can then be compared to their laboratory synthesized counterparts through the quantification of structural features such as porosity and surface area per unit volume, which in tum are used to inform the foam's fluid transport propertiesThe spherical template particle packing algorithm developed here is adopted from Powell's work [1], which also includes approaches to obtain percolation and density in random packings [2]. Gervois gives a mathematical development for the stereological sectioning of packed hard spheres [3]. Stereological sectioning facilitates determination of relevant three dimensional morphological properties from two-dimensional data [4]. Studies on the sphere distribution size and the related particle packing density and coordination number results are studied in [5, 6]. Lastly, Kato describes a sintered neck structure, which is used with these packings [7]. This neck structure, as a model of the particle shape following heat treatment, is implemented here in a similar manner. A strong difference between the available literature and the methodology here is that spheres are packed to ultimately represent porous space, not rigid solid space."

Jan 1, 2011

By Yongbin Yang, Meixia Cai, Yufeng Guo, Guanzhou Qiu, Tao Jiang, Jianjun Fan

"A series of sintering and metallurgical experiments were carried out to optimize the blast furnace burden structure in this study. The results indicated that the sinter disintegrated seriously with basicity around 1.4, and after this “turning point”, the sintering properties were improved gradually with the increase of basicity of sinter. Based on the results, an idea was put forward which focused on producing two different kinds of sinter with different basicity. Different with the original burden structure of 85% sinter with basicity 1.4-1.5 + 15% pellets, an alternative new BF burden structure was proposed by the following structure?44% sinter with basicity 1.05 + 44% sinter with basicity 1.87 + 12% pellets. This new alternative BF burden structure has been adopted by some steel plants.IntroductionIn recent years, conventional blast furnace (BF) process was put into operation to produce hot metal in “A” steel plant. “A” steel plant owns two sets of sinter strands at present. Because the sinter production capacity exceeds the actual requirements of BF, a burden structure with 85-90% self-made sinter + 10-15% purchased pellets is adopted to take advantage of the low–cost sinter. But the serious problems encountered with the BF operators are that the sinter disintegrated easily during transportation and storage process. Therefore, the rate of return fines is very high after sinter being screened."

Jan 1, 2012

By Mikiya Tanaka

This paper outlines our attempt to establish a recycle process of nickel in the spent baths and waste rinse water of electroless nickel plating plants using solvent extraction and solvent-impregnated support, Solvent extraction studies of nickel from actual spent baths revealed that (i) nickel is efficiently extracted by a hydroxyoxime extractant such as LIX84I at a pH greater than 6 and is readily stripped with sulfuric acid, and (ii) the mixtures of LIX63 and acidic organophosphorus extractants (D2ERP A, PC88A, and Cyanex 272) enhanee the nickel extraction efficiency to a sufficient degree without pH adjustment, but at the same time, reduce the stripping efficiency. The application of acidic organophosphorus extractants to selectively remove impurity metal ions (iron and zinc) from a real spent bath before extracting nickel lead to the finding that PC88A and Cyanex 272 effectively remove iron and zinc without pH adjustment leaving nickel in the raffinate. The removal of nickel from the waste rinse water was also studied. Solvent-impregnated supports with a macroporous resin and oil sorbents made of natural kapok fiber and synthetic fiber as supports were applied using D2EHPA and LIX860 as the extractants. During the batch operation, nickel is removed with a high efficiency without pH adjustment. During the column operation, however, the effective removal is hindered by (i) the dissolution of the nickel-D2EHPA complex into the aqueous phase in the high loading region, and (ii) the slow removal rate of the LIX860-impregnated support.

Jan 1, 2003

By M. C. Ruiz

In the present study, the size distribution, Fo(v), of organic drops produced in a continuous-mixing vessel has been determined experimentally for various conditions. The organic phase used was a 1: 1 mixture of a salicylaldoxime (LIX 860N-IC) and a ketoxime (LIX 64-IC) in an aliphatic diluent (Escaid 103). The aqueous phase was a copper sulfate solution. The results indicated that an increase in stirring speed, extractant concentration, and pH produced smaller drops. The effect of the stirring speed was the most significant, decreasing the average volume of drops by 57 % for a change from 300 to 400 rpm. On the contrary, an increase in the dispersed phase fraction, copper sulfate concentration, and retention time produced larger drops. Changes in temperature from 23 to 30°C did not affect significantly the drop sizes. In all cases, the experimental drop size distributions could be accurately represented by a lognormal distribution.

Jan 1, 2001

By Chen-Ming Kuo, Esher Hsu

"Under the 4-in-1 recycling system, Taiwan producers and importers who using packaging containers have responsibility to pay the recycling fees for recycling the waste packaging containers they produced or imported; while the collectors/recycling plants who collect/sort/recover waste packaging containers receive subsidy for conducting recycling. A reasonable pricing for recycling charge and subsidy is a way for sustainability of the recycling. The objective of this study is to provide an amending mechanism for product charge and recycling subsidy in response to the social economic changes. This study employs a regression analysis and cost adjusting model to link the factors used for calculating product charge and recycling subsidy on recycling waste packaging containers with socio-economic indicators, raw material prices, wholesale prices, and secondary material prices. Study results provide estimated models to EPA in Taiwan for amending product charge and recycling subsidy in response to the social economic changes.IntroductionUnder ""4-in-1"" recycling system in Taiwan, waste packaging containers are officially announced to be recycled. The waste packaging containers announced to be recycled include iron cans, aluminum cans, glass bottles, plastic containers, paper containers, aluminum foiled paper packs. In order to compensate the recycling system, EPA charges associated manufacturers and importers for recycling fee and subsidies recyclers to create the economic incentive for raising recycling performance. Basically, the budget for subsidy recyclers is from the recycling charge. That means if we want to increase recycling efficiency by increasing subsidy to recyclers then the manufacturers and importers have to pay more for reaching financial balance of recycling foundation. The benefit of recyclers and fee payers are always conflicted. The recycling charge and subsidy is thus argued by fee payers and subsidy receivers all the time. A reasonable pricing for recycling charge and subsidy is the only way to keep the recycling system sustainable. Moreover, a suitable mechanism has to be changed along with the changing social economic condition. The recycling performances and effectiveness of this recycling system is also highly dependent on the pricing mechanism. This study intends to provide an amending mechanism for product charge and recycling subsidy in response to the social economic change. Related previous studies about recycling system in Taiwan with its performance include Hsu and Kuo (2002, 2005), Bor, Chien, and Hsu (2004) and Hsu (1999). Hsu and Kuo [1] estimated total production values of recycling and evaluated the performance of recycling performance based upon the estimated production values."

Jan 1, 2011

By V. I. Lakshmanan

Wastes when produced can be reused or recycled prior to disposal. Industries that cause environmental concerns during manufacturing include primary materials and primary metals. Pollution prevention mechanisms to achieve waste reduction require new separation, reclamation, control and process simulation technologies. Substituting recyclables for virgin resources will reduce energy use, water pollution, air pollution, water use and mining wastes. Shrinking landfill space will spur new technologies for waste treatment and recycling. These situations hence offer opportunities for innovative flowsheets with appropriate separation technologies. Development of innovative flowsheets to treat recyclables offer unique opportunities for process/product development, obtain green products and hence market advantage. The paper will illustrate with selected innovative flowsheets to treat recyclables.

Jan 1, 1996

By Kun Wang, Xinhui Li, Huaqing Xie, Qingbo Yu, Qin Qin

"Three typical model compounds of bio-oil (ethanol, acetone and phenol) were studied in the steam reforming process for hydrogen production. In the thermodynamic analysis, the three componds showed the similar trends. The hydrogen yields increased with the increase of steam/carbon (S/C) ratios, and the temperatures of the maximum hydrogen yields moved afterward to low temperature zone. However, the hydrogen contents were just about 70%. For improving hydrogen yield, a new system for steam reforming of bio-oil with site CO2 capture was put forward. This system required the catalst with the larger granularity having greater mechanical strength and higher abrasion resistance. So, six Ni-base catalysts loaded on Al2O3 particles prepared were used and among them, Mg-Ni/Co catalyst showed the best catalytic performance. For the simulated bio-oil (the mixture of the compounds), the hydrogen yield can attain 63% with Mg-Ni/Co catalyst with the good stability and regeneration ability.IntroductionCurrently the interest in the use of hydrogen as a clean energy carrier is increasing, and the main way for producing hydrogen is steam reforming of fossil fuels, containing steam reforming of nature gas, naphtha and coal. But this way caused substantial amounts of CO2 emitted, and these sources of hydrogen which are non-renewable energy will eventually be used up [1, 2]. As a kind of renewable energy, biomass is recognized as an attractive alternative to fossil fuels, because of its neutral CO2 emissions [3]. There are mainly two thermochemical processes using biomass to produce hydrogen, gasification and flash pyrolysis followed by steam reforming (SR) of the biooil produced in the flash pryolysis process [4]. The latter was known as one of the most promising and economically viable methods for hydrogen production [5]. In the last decades, the biomass flash pyrolysis technology was adequately developed and fairly mature [6]. But the steam reforming of bio-oil is still at the research stage and yet has been leading to more and more concerns by the researchers. In their research, the catalysts were widely studied and yet mainly were powdery[7-10], and the reactors manily were fixed bed reactors[11-13], readly causing the carbon deposition and the catalyst deactivation, against the continuous running. In this paper, a new systerm was put forward and could realize continuous production of hydrogen, yet needed catalysts with the larger granularity having greater mechanical strength and higher abrasion resistance, as well as powdery CO2 sorbents which mainly calcium oxide based ones.In this paper, the thermodynamic analysis of the steam reforming processes of three typical bio-oil model compounds (ethanol, acetone, phenol) was performed, and the effect of S/C ratio and temperature on the hydrogen yield and the compositions of gaseous products were investigated. Then, a new systerm for steam reforming of bio-oil with site CO2 capture was put forward, and the catalysts with a certain granularity were prepared and studied."

Jan 1, 2014

By Masanori Abe, Yoshitaka Kitamoto, Kazuhiro Nishimura

"Ferrite plating is a chemical processing which utilizes Fe2+ - Fe3+ oxidation to synthesizing polycrystalline films of ferromagnetic spinels (MFe20 4, M = Fe, Co, Ni, Zn, Al, Cr, TI, etc:) directly from an aqueous solution at 24 - 100°C. This low temperature process allows us to fabricate new ferrite film devices on · substrates of such non-heat-resistant materials as plastics, GaAs integrated circuits, and biomaterials. Synthesized from an aqueous solution the ferrite plated ·films are highly biocompatible. Thus various magnetic device and biomedical applications have been proposed and realized using ferrite-plated films. Ferrite-encapsulated polymer microspheres are applied to antibody carries for enzyme immunoassay, and also to toners/carriers for photocopying. Perpendicular magnetic recording media utilizing plated CoNi ferrite films are proposed. The low-temperature synthesized films of NiZn and Co ferrites are potentially used as soft-magnetic and/or insulating layers, respectively at high/microwave frequencies.IntroductionFerrite plating is a processing which facilitates the formation of crystalline spinel ferrite films with various compositions, (Fe, M)30 4 (M = Fe, Co, Ni, Zn, Al, Cr, TI, etc.), directly from an aqueous solution at 60 - 100°C [1]. This opened the door to fabricating novel ferrite-film devices using substrates of such non-heat-resistant materials as plastics and GaAs integrated circuits [2-4]; conventional ferrite film preparation techniques such as sputtering, vacuum evaporation, MBE, LPE, etc., require high temperatures(> -600°C) for crystallization of ferrites, which deteriorates the non-heat-resistant substrates. Recently we extended ferrite plating to be preformed at room temperature [5, 6]. This enables us to use as substrates such organic materials as biomaterials (e.g. enzymes) having very low heat-resistance."

Jan 1, 2000

By J. Priede, G. Gerbeth

"Two different instability mechanisms of electromagnetically levitated bodies are analyzed. The first is due to the virtual coupling between the electric current passing through the magnetic system and the variation of position of the body. This mechanism can result in unstable mass center oscillations of a levitated solid body. Another type of instabilities may occur because of the coupling between the motion and the electric currents induced in the body. This effect can cause a spontaneous rotation of the body setting in as the frequency of the alternating magnetic field exceeds certain critical threshold depending on the configuration of the field. This instability can be suppressed by an axial steady magnetic field of strength comparable to that of the levitating field. 1 IntroductionAn alternating magnetic field interacting with eddy currents induced in a conducting body causes repulsion between the body and the coil generating the field. Besides, the eddy currents provide a contactless heating of the body. In such a way metallic samples can be levitated and melted without a contacting crucible. This technique allows to avoid contamination of the melt with container material and so to achieve a considerable super-cooling of the melt before it solidifies. Nowadays electromagnetic levitation is widely used in material research for measuring of the thermophysical properties of molten metals (2) .It has been observed since early fifties when the first experiments on the electromagnetic levitation were done that under certain circumstances solid levitated samples start to rotate or oscillate [l]. Surface oscillations can appear in addition when the sample is melted. Such phenomena are undesirable because they often result in failure of the levitation. Recently we showed that rotational as well as oscillatory instabilities can have electrodynamic origin related to additional eddy currents induced by motion of the body in an alternating magnetic field [3] , [4].In the first part of the present paper we analyze another possible cause of oscillatory instability due to the coupling between the electric current passing trough the magnetic system with variation of the position of the levitated body. The second part of the paper deals with the origin and suppression of rotational instability in a uniform alternating magnetic field."

Jan 1, 1999

By W. D. Keller

Scanning electron microscopy (SEM) accompanied by X-ray energy dispersive analysis (XES) is a useful tool in process clay mineralogy. The texture of kaolin, illustrated by SEM, gives a clue to its mode of genesis and probable industrial application. One type of kaolin, originating dominantly by weathering, has an open texture, slakes readily, and is used for filling and coating paper. Another type, in contrast, originates by diagenesis of Al-silicate sediments, and spectacularly resists slaking, thereby enabling it to maintain its bulk density and controlled size and shape of particles after crushing and moistening; this meets an important requirement for the manufacture of refractories. Ratios of elemental Al:Si that may be rapidly determined by SEM and XES yield information on the origin and purity of bauxite and bauxitic clays, and aid in quality control and processing of them. SEM of dissimilar textures of quartz, as in chert and novaculite, are evidence for geothermometry on a stratigraphic scale that is potentially useful in delimiting thermally favorable or unfavorable areas for hydrocarbon exploration, and possibly for unexposed metallic ore deposits.

Jan 1, 1982

By Yasuhiro Konishi, Norizoh Saitoh

"We have developed new recycling technologies, based upon an eco-friendly biotechnology, in order to extract precious and rare metals sourced from post-consumer products. Recently we have been focusing on the metal ion-reducing bacteria, Shewanella algae and Shewanella oneidensis, which are able to reduce and deposit the precious metal ions (gold (III), platinum (IV), palladium (II), and rhodium (Ill)) into metal nanoparticles at room temperature within 120 min. When targeting the leachates from printed circuit boards, the Shewanella bacteria were able to allow selective reduction and deposition of gold (III) ions under acidic conditions in the presence of heavy metal ions, proposing a new bio-recovery system for gold. We also found that the Shewanella bacteria can separate and concentrate soluble rare metal ions (dysprosium (III), indium (Ill), and gallium (Ill)) from dilute solutions. Using this biomass adsorbent, the effectiveness of system for the novel recovery of indium from the leachate of used LCD (liquid crystal display) panels has been demonstrated.IntroductionMany high-tech manufacturing industries are highly dependent upon the use of critical raw materials that are the rare metals (e.g. rare earth elements/indium) and precious metals (e.g. gold/platinum group metals). There are now serious global concerns over the short term and long term availability of critical raw materials for high-tech manufacturing. This highlights the paramount importance of sustainable component reuse and material recycling technologies for recovery of critical raw materials. We believe that the most important domestic source of precious metals is through more recycling, and this will require more research and further development for the recycling of precious and rare metals. In general, chemical/thermal recycling is deemed to be the most appropriate means to extract the precious and rare metals from postconsumer products. However, there are issues related to the heavy use of toxic and hazardous chemicals, and the release of toxic emissions.Biological recovery methods provide an attractive alternative strategy and use microorganisms to separate and concentrate soluble precious and rare metals from dilute solutions into microbial cells via biosorption [1-3] and biomineralization [ 4, 5]. Biological systems generally operate at ambient temperature and near-neutral pH. Consequently, microbial recovery of metals would be an environmentally friendly method for recycling precious and rare metals from end-of-use products."

Jan 1, 2014

By Katsutoshi Inoue

Pectic acid gel crosslinked with epichlorohydrin was found to have very high selectivity to lead(II) and iron(III) ions over zinc(II) ion compared with commercial weakly cation exchange resins containing the same carboxylic functional groups, suitable for removing small amount of impurity metal ions from waste zinc plating solutions. In order to lower the cost, new adsorption gel was prepared from orange juice residue containing pectic acid by crosslinking with epichlorohydrin, which was also found to be suitable for removing these impurities. Further, very cheap adsorption gels was prepared not only from orange but also from apple juice residues by a simple method through just saponificating pectin substances contained in these residues into pectic acid by calcium hydroxide followed by water washing and drying. These adsorption gels exhibited excellent adsorption behaviors for removing the impurity metal ions away from zinc.

Jan 1, 2003

By S. K. Wu, Ray Y. Lin, Sunil Annaji

Infrared joining of TiAI using aluminum foils as the filler material was investigated at temperatures between 1050 °C and 1350 °C in a flowing argon environment for times varying between 15 and 60 seconds. Using aluminum foils, the attempt was to form the Al3Ti phase in the joint as a result of reaction between Al and TiAI at temperatures above the melting point of Al. It has been found based on X-ray diffraction and TEM analysis that, Al3Ti, indeed is the product of infrared joining of TiAI using Al as the joining alloy. Al3 Ti was detected even in the joint processed at 1050 °C for only 15 seconds. Since the aluminum foil used in this study contains 27 at% Si, the t 2 phase in the Ti-Al-Si ternary system is believed to have also formed at the joint/base TiAI interface. Cross sectional studies on the joined specimens have shown different degrees of reaction depending on the temperature and time of joining. Micro hardness evaluations across the joint show that the hardness near the center of the joint is typically smaller than that near the joint edge next to the base material. However, as the joining temperature and time increase, the increment of the hardness at the center of the joint is faster than that around the periphery of the joint.

Jan 1, 1996

By lchiro Aoi, Hideo Nakae, Makoto Yoshida, Makoto Ishino

"The influence 6f gravity on the microstructure of unidirectionally solidified Cu-Pb monotectic, Ag-Si and Fe-C eutectic alloys is studied. In order to examine the influence of gravity in a lg environment, both the upward (opposite to direction of gravity) and downward (direction of gravity) unidirectional solidifications are carried out. The results are as follows: (1) For the upward solidified Ag-Si eutectic alloy, the eutectic Si continuously grows. On the other hand, in the downward solidified Ag-Si alloy, the Si grows discontinuously and disperses into the ex-Ag matrix. (2) No morphological difference in the eutectic growth is observed between the upward and downward solidified Fe-C eutectic alloys. (3) In the case of the upward solidified Cu-Pb monotectic alloy, a banded structure, which consists of Pb-rich layers and Cu-rich layers, is observed. However, such a banded structure -is not observed in the downward specimen. (4) The banded structure is not found in the upward solidified Cu-Pb-0.05 mass % Al and Cu-Pb-0.1 mass % Al alloys. In the Cu-Pb-0.05 mass% Al alloy, a fibrous -L 2 phase grows continuously parallel to the growth direction at low growth rate. Only 500 mass ppm addition of aluminum induces the morphological change of the monotectic L2 phase.IntroductionThe influence of gravity on the solidification of eutectic and monotectic alloys has been investigated in microgravity environments [l-9]. The purpose of these studies was to obtain a homogeneous microstructure of eutectic or monotectic alloys, most of which alloys tend to solidify with macro-segregation under gravity. However, in most of the previous experiments, e.g., in free fall systems, in aircraft or in space laboratories, the growth rate was too high to realize a planar solid/liquid interface. This would be due to the limited time for solidification. Thus, it was difficult to examine the influence of gravity on the planar coupled growth of the eutectic or monotectic alloy. In this study, both the downward U.D.S. (unidirectional solidification by gravity) and upward U.D.S. (opposite direction to gravity) are carried out in order to examine the influence of gravity on the coupled growth in a lg environment [l0, 11]. In the case of the downward U.D.S. using the current Bridgman method, the molten alloy must be confined between the crucible and the solid."

Jan 1, 2000

By I. Iwasaki

Platinum group elements (PGE) are often found in arsenide and sulfarsenide minerals as inclusions in copper-nickel bearing gabbroic rocks. Major losses of platinum in flotation have been attributed to the poor recoveries of the arsenic minerals. Flotation characteristics of a synthetic nickel arsenide and arsenopyrite were studied through rest potential and oxidation rate determinations, surface analyses, and micro-and batch-flotation tests. The use of nitrogen during grinding and flotation together with copper activation improved the PGE recoveries from Duluth Complex ores. The flotation behaviors of the sulfarsenide minerals are still unresolved. The role that electrochemical interactions play among arsenides, sulfarsenides, sulfides and grinding media on their f10atabilities is discussed.

Jan 1, 1988

By Rolf R. von Oppenfeld

Onsite hazardous waste processors often find obtaining a Treatment Storage and Disposal (TSD) permit one of their first major challenges. Some processors may spend the time and money required by the permitting process, only to find out later that a permit was not necessary. This paper will present and analyze four strategies that processors may use to avoid obtaining a TSD permit. Some facilities will be able to remove their waste streams from RCRA's oversight by ensuring the material is not "hazardous" waste. Parties that treat waste while it is in process may be able to avoid generating "waste" altogether. Certain treatment facilities have been specifically exempted by EPA. Finally, treatment of waste while it is in generator storage tanks may be allowed without a RCRA TSD permit. Hazardous waste point of generation, an important determination relating to these strategies, will also be discussed. Generators and processors will find this paper useful when evaluating their permit exemption potential

Jan 1, 1996