Search Documents

By George J. Conroy

Results of a long-term program of electrical parameter measurement in under-ground coal mine working sections, performed by The Pennsylvania State University under U. S. Bureau of Mines sponsorship, are utilized as the basis for an analysis of the electrical energy requirements during operation. A model section is hypothesized, developed from the average or most representative characteristics as determined from tabulations of the measurements. Performance factors of the model section's machine complement are then analyzed, particularly with regard to the energy required per ton of raw coal cut and delivered from the section. Results are given in kilowatt-hours per ton.

Jan 1, 1977

By Timothy C. Richmond

The Stillwater District is located in south central Montana approximately 75 miles southwest of Billings, the state's largest city. It lies along the northeast front of the Beartooth Mountains and is within the boundaries of the Custer and Gelatin National Forests. The district contains some of the nation's most spectacular mountain scenery. Montana's highest peaks, including 12,799 foot Granite Peak, rise a few miles south of the area. Much of the district is located on a gently undulating plateau which averages 8500 ft. above sea level, broken by hills up to 10,000 feet and slashed by glacially carved canyons, some of which are more than 3,000 feet deep.(Fig. 1) Immediately to the north and east, the land falls away to the Great Plains, stretching unbroken to the Mississippi River. Two major tributaries of the Yellowstone River, the Stillwater and Boulder Rivers, traverse the area and several large streams originate in the district itself. Access to the high mountain country and the adjoining Beartooth Primitive Area is restricted to a few horse and jeep trails continuing from the terminus of improved roads in the bottom of the Stillwater and Boulder Valleys. Hunters, fishermen and cabin owners make intensive use of the area along its improved transportation routes, but hikers seldom venture more than three miles beyond the end of the roads. People from the Billings area are the most frequent visitors.

Jan 1, 1974

By Thiemo Hagedorn, Gerhard Weissbach, Ralph Bergmann, Wilhelm J. Kogelmann

The objective of this unique method is to multiply the advance rate of conventional tunneling while improving both ground control and the safety of the crew. The high advance rate is achieved by concurrent rock excavation and installation of concrete lining at fully synchronized work phases. The novel TACHUSMATIC system consists of a high-production, robotic cutter boom, an automated slip form and continuous mucking and conveying. This novel system utilizes the inherent bearing capacity of the rock that is activated by a small, initial deformation. The supporting resistance is then provided both by the rock mass itself and the pumped in concrete lining. During the hardening of the concrete, the hydraulic cylinders of the TACHUSMATIC automatically apply the appropriate support resistance, thus providing safe ground control. This novel tunneling system is practically a fully automated, fail-safe NATM that does not require highly skilled engineers and crew. The TACHUSMATIC can be used for construction of circular, rectangular and horseshoe-shaped tunnels. When equipped with the Alpine Multi-Tool Miner (MTM) systems, the machine can work in a wide range of ground and rock conditions. The use of novel, diamond-tipped cutter bits (picks) will increase hard rock cutting capabilities and will significantly reduce pick consumption. Because of its moderate cost, the novel system is an economic alternative to conventional tunneling even at short drivages. A new installation is cost-effective for tunnels longer than 750 meters (2,500 ft.) At a typical tunneling project, the cost permeter is about 25% lower than with conventional methods.

Jan 1, 2003

By A. T. Visser

The expansion of surface mining has led to the development of very large off-highway trucks currently capable of hauling payloads in excess of 290t. Mine haul roads have historically been designed empirically, relying heavily on local experience; the trend in increasing truck size will thus render the current pavement systems inadequate. Since truck haulage costs can account for 10%-50% of the total costs incurred by a surface mine, not only would the maintenance costs of existing roads of inadequate design increase, vehicle operating and maintenance costs would also increase prohibitively. There is thus a need for improved design technologies encompassing the construction and management techniques of mine haul roads, appropriate for the wheel loads of vehicles now in use. The aim of the paper is to present the different components of a mine haul road design and management system and to demonstrate the value of its application through case studies. The system has been applied at several South-African surface mines and distinct benefits have been derived. The improved structural design of a new road resulted in a 29% saving in construction costs and also provided better service, whilst the optimal selection and management of wearing-course materials provided better functionality at lower total transportation operating costs.

Jan 1, 1999

By P. G. Semple

For the last four years, the Kilborn Group of Companies has been involved in several major projects in the Confederation of Independent States (CIS). These include the Kumtor project, the Kubaka gold project, the Kazgold project, the Aginskoe project and the Jerooy project. These projects are all in various stages of detailed engineering and construction. Western mining companies are pursuing mining opportunities throughout the world in search of ore bodies for development. The quest for profitable mining ventures has led mining companies to South America and Asia and, more recently, to the former Soviet Union. When considering the CIS, several factors should be considered. The most notable are geography, mining culture and previous mining production.

Jan 1, 1996

By Sean Harvey

One of the manifestations of the dynamically induced failures in deep coal mines is the violent ejection of coal from the ribs. A possible protection against such failures is the use of a specifically designed dynamic support system with reinforcement units having the sufficient capacity to absorb the kinetic energy of the dynamic failure and a skin support that can adequately contain the disintegrated coal. With this method of mitigation in mind, a recently introduced yielding rock bolt, trade name Roofex, has been identified (Harvey and Ozbay, 2009) as a possible energy absorbing component of a dynamic support system. According to the manufacturer?s specification, the Roofex bolts can yield 300 mm (or more) displacement while holding 80 kN pull load. In order to assess the performance of this support unit in coal ribs, a series of in situ pull tests performed in two coal mines in Colorado. The results show that, under conventional pull test loading conditions, Roofex yielding bolts perform very close to their claimed specifications, thus showing a potential for their use as the main energy absorbing component of a dynamic support system. Further studies are required to confirm the in situ performance of these bolts under dynamic loading conditions and also to develop a containment component for a dynamic support system for the mitigation of dynamic coal rib failures.

Jan 1, 2009

By Leo Gentile, David Selhorst

The $528 million Toledo Waterways Initiative (TWI) was implemented by the City of Toledo in 2002 and completed in August 2020. Toledo is one of many US cities required to implement a Long-Term Control Plan (LTCP) but one of few to have completed its plan. TWI consists of three storage and conveyance tunnels, four below grade storage basins ranging from 4 to 36 million gallons (MG), miles of sewer separation and interceptor improvements, green infrastructure and other appurtenant structures to dramatically reduce combined sewer overflows to the Maumee River, Ottawa River and Swan Creek. All three rivers flow into Lake Erie. The City’s 180-year history as a Midwest shipping, manufacturing and transportation hub provided design engineers and contractors no shortage of unknown underground challenges to complete the projects. The City will begin its 5-year Post-Construction Compliance Monitoring in 2021 to satisfy the final LTCP requirement. A program overview and experience from tunnel and underground basin construction in urban areas with buried active and legacy infrastructure will be discussed.

Jun 13, 2021

By P. J. Ryan

Phelps Dodge’s Candelaria copper-gold mine is located 20 km (12miles) south of Copiapó in northern Chile’s Atacama province (Region III) (Fig. 1). The Candelaria Mine is about 800 km (500miles) north of Santiago and 75 km (47 miles) east of the Pacific Ocean. Its elevation is 600 m (1,970 ft) above sea level. The Copiapó River Valley is 6 km (4 miles) northeast of the mine site. It is the only major source of water in this arid region. The average rainfall is 14mm/a (0.5 in./year). During 1995, the mine produced 521.4 kt (574,800 st) of copper concentrate containing 150 kt (165,000 st) of salable copper and 3 t (98,800 oz) of gold. The 1995 unit cash cost was less than 50 cents/lb of copper. This makes Candelaria one the world’s lowest cost copper producers.

Jan 1, 1996

By Robin Dill, Julian Prada, Kathryn Kelly, Brian Hann, Todd Moline

Narragansett Bay Commission’s (NBC) Pawtucket Tunnel Project includes construction of the 11,600-ft long, 30-ft ID, deep rock tunnel. This paper presents insight into the features and benefits of lump-sum, design-build that led NBC to select it as the project delivery method. The use of a design-build contracting process that included proprietary meetings to discuss and obtain feedback on Alternative Technical Concepts as well as to facilitate reaching consensus on modifications to the GBR-B is also described. The discussion includes features and benefits of design-build process that not only addressed NBC’s desired outcomes, but also allowed the Design-Builder to propose several innovative changes to the Base Technical Concepts included in the bid documents, and to develop a GBR-C that was compatible with their proposed means and methods of construction and addressed what they believed to be the more significant subsurface risks on the project.

Jun 13, 2023

By Nan Hua

As a high production and high efficient mining method, top coal caving method is now widely used in China. However, as more extra-thick coal seams are mined, it becomes more and more difficult to make the top coal fully broken up, resulting in more and more top coals flowing into the gob, rather than onto the rear AFC at the working face as designed. This research is aimed to investigate the failure mechanisms of the extra-thick top coal caving mining method.

Jan 1, 2009

By Hamid Maleki

Mine seismicity is influenced by the mechanical properties of both near-seam rocks and overburden and the prudent selection of mining methods and mine layout designs. Using finite-difference modeling, experience in many U.S. mines and measurements of the pressure arch width, the author has reviewed the engineering design factors that control seismicity in room-and-pillar retreat operations for stiff stratigraphic conditions in deep western U.S. mines. By back analyzing the overburden response in now understood to have been inadequately designed historic room-and-pillar mine, the overburden collapse mechanism is addressed as well as the need for improvements in designs including panel and barrier pillar widths, and sequence of retreat.

Jan 1, 2009

By A. H. Srnallbone

Over the past few years the rising production costs, shortage of skilled labor, and increased use of lower grade ore bodies have all added justification for the use of on-stream analysis. A rise in the number of on-stream units indicates that this type of assay is now being accepted as a necessity. On-stream analysis is a much more rapid means of obtaining true assays of a flowing product when compared to wet chemistry or "grab" samples dried, briquetted and assayed by x-ray. In contrast, on-stream analysis uses real time samples assayed every 30 seconds while each stream is assayed every 5 to 15 minutes. It is very important not only to know that a change has occurred in the process, but to know what caused the change and how to correct for the change. For example, in a tailing sample the elements of interest comprise between 1% and 10% of the sample. The remainder is water and gangue. Previously the gangue was not assayed nor were the low atomic number elements used for corrections. In addition to the demand for higher accuracies some concentrators were being penalized for excessive Ca or in some cases 5i in their concentrates. This penalty was being imposed by the smelter in order that they could better cope with pollution problems and prolong the life of their furnaces. But until Ca, 5i, and S are measured on-line, nothing can be done about their control. By accurately measuring these light elements on-line, a complete assay is obtained of the total sample providing improved accuracy for the important products. The justification for complete accuracy assays is now even more obvious because they are possible at very 1ittle increased cost and at no increase in analytical time.

Jan 1, 1977

In this paper, a number of novel hypotheses that provide a fresh perspective on the characterization of strata movements associated with longwall mining are developed by analyzing subsidence measurements with an influence- function-based computer program. With this influence-function technique, easily obtained surface displacements can be used to determine some of the complicated, expensive, and difficult to measure movements of the immediate roof strata in a longwall panel. The primary hypothesis developed by this analysis proposes the existence of an area of partial roof caving near the edge of a panel called the "edge effect." A second hypothesis, interrelated with the first, promotes the importance of the effect of gate-entry closure on the observed strata movements. Both the primary edge effect hypothesis and the secondary hypothesis concerning gate-entry closure are justified and quantified in an extensive analysis of surface subsidence that uses supporting information from related theories, design criteria and insitu measurements. Next, the edge effect and the gate closure hypotheses are extended further and used to provide an explanation of the complex subsidence interaction of adjacent longwall panels in what is termed a "redisturbed" effect. Finally, in the conclusions of this paper, the importance of accurately understanding these longwall strata movements for proper subsidence prediction or gate design is stressed.

Jan 1, 1986

By Diler Katircioglu-Bayel, Oner Yusuf Toraman, Safak Gokhan Ozkan

One of the most energy-intensive processes for producing submicron range calcite is stirred media mill. In the present work, numerous operating parameters such as solid mass fraction, grinding media size, media filling ratio, and grinding time have been investigated using a vertical type stirred media mill. The results are evaluated on the basis of mean particle size, specific surface area, and specific energy consumption. After conducting this study, optimum experimental conditions found to be as 70% media filling ratio, 25% solid mass fraction, 1 mm grinding media size, and 120 min grinding time. Besides, energy savings up to 22% were achieved with the choice of proper media size.

By W. S. Weldon

The use of spiral separators for the beneficiation of fine coal typically in the size range -2+0.1mm is now well established process technology. Developments during the mid 1980's resulted in the production of cost effective, efficient large diameter coal spiral separators. Recent developments and research have been geared to optimize metallurgical performance, materials handling and equipment geometry of large diameter coal spiral separators.

Jan 1, 1997

By Andre C. Zingano

It is a very difficult task to estimate the immediate roof and support behavior in a room-and-pillar mining section in the initial phase of the mining project. There is little information available at this phase, and it is restricted to geomechanic characterization of the rock layers from cores samples, and the in-situ instrumentation of experimental entries and intersections. Even being a pilot excavation for roof support test a good indicator for the behavior of the immediate roof, its behavior for a full excavation mining section is different from a single intersection of two entries, mainly because the stress redistribution caused by the multiple entries excavation and face advance for a full excavation section. The objective of this paper was to calibrate a 3-D numerical model of an experimental intersection, based on the in-situ instrumentation of an experimental intersection excavation, and the geomechanic description of the rock layers. The numerical model was built with the same specifications as the excavation test, including the entry geometry and roof support. The numerical model calibration was based on wire extensometers that were installed at different positions in the roof of the pilot excavation, and on the geomechanic characterization of the rock layers that form the roof, coal seam, and floor. Therefore, it is possible to estimate whether the roof support specification adopted in the test phase will be good enough for the development of the entire mining section.

Jan 1, 2009

As the surface reserves are being depleted, more and more stone operators are seeking underground mining options. Stability of underground openings is a major concern for the safety and productivity. This paper relates to a field study conducted at a large underground limestone mine in Central Pennsylvania. Identification of hazards leading to ground failures and assessment of roof fall risks are important in mitigating injuries. Field observations at this mine were integrated with Roof Fall Risk Index (RFRI) mapping software recently developed by West Virginia University. The system is designed to combine field study data related to geologic factors, mining-induced damages, roof profile, and ground water influx to generate RFRI maps. The mine has adopted a proactive ground control program consisting of comprehensive examination of drilling and bolting logs; precision surveying of roof and rib; accurate mapping of cutters, falls, and geologic structures; and installation of extensometers and microseismic monitoring systems. Investment of time and resources has eliminated fatalities and lost-time injuries due to ground fall. This paper presents the geologic settings, mining conditions, ground control issues along with risk management and control techniques adopted at the study mine.

Jan 1, 2009

By Jeffrey K. Whyatt

The Crandall Canyon accident investigation included an interesting and unexplained observation by rescuers that the ?barrier rib had shifted northward as a unit, as much as 10 feet.? This is not the first mention of such a movement, although such reports are rare. Historical accounts describe unusual movement and displacement of intact coal, cribs and timbers. Two movements of particular interest are the creation of gaps above coal pillars and falling of standing support elements without apparent damage. A dynamic boundary element program was used to explore movements induced by slip on geologic features removed from the affected panel. While the resulting models are much too simple to fully replicate these observations, they do show that the types of phenomena observed are possible. They can also provide insight into the types of motions that ground support elements are subjected to during large bump events. This was demonstrated for the case of a large bump in a Book Cliffs coal mine. Seismic information suggested the source mechanism to be normal slip on a fault. A model of that source showed initial dilation of the panel followed by dynamic compression and rebound ? consistent with underground observations. The initial dilation is important as it may allow slender standing support to shift or fall.

Jan 1, 2009

By V. K. Gupta

The experimental results of some wet batch and continuous grinding experiments carried out in a 40 x 40 cm grate discharge ball mill have been analyzed for the variation of the grinding rate parameters, Si, with various operating conditions using a linearized population balance model. The wet grinding tests were carried out under conditions which were very similar to those encountered in the actual practice in plant operation. Well distributed -4 and -20 mesh feeds of two complex pyritic ores were used. The volume-percent solids in the pulp ranged from 30-40, the particle load from 5-8 kg, and the solids feed rate from 70-1 10 kg/hr.

Jan 1, 1981

By Stanley M. Moos

In reviewing available vacuum filtration equipment in this paper, several types of filters have been included which are probably not familiar to operators in the mining industry. However, it was felt that these units might be of interest in the event that an application should arise for the filtration of a product in the future that does not exist today. In addition, exposure of our industry to equipment used in other industries might have a tendency to be thought provoking and perhaps lead to the development of equipment and/or applications in our industry which do not necessarily exist at this time. Most innovations in filtration equipment have been confined to the improvement or design change of components and accessories, particularly reflecting the availability of materials of construction that have been developed. Recent developments in the application of horizontal belt filters have been innovative. The application of this unit as a substitute for or an adjunct to thickeners in a CO circuit can certainly be innovative and perhaps provide a basis for reduction in capital and operating costs in this area. For example, mill tails are generally pumped at the highest possible density that will adequately flow. Tailings ponds and dams with their attendant design requirements are based upon this estimated water volume. Availability of a much dryer, non-flowing filter cake opens up several new options for disposal. Considerable cost savings could result in the design and planning of disposal areas for containing dryer material. . No attempt has been made in this paper to provide a manual for the operation of all of the many types of equipment that are available. Rather, the paper tries to present an overview.

Jan 1, 1978