Search Documents

By A. Visnapuu

Excessive noise and high vibration are inherently associated with equipment used in the mining, extraction, and processing of mineral resources. High vibration degrades structural components, often leading to catastrophic failure and loss of productivity, and excessive noise can result in permanent hearing loss. In order to foster efficient utilization of the Nation's mineral resources and minimize occupational hazards associated with mineral processing, the Bureau of Mines investigated the relationship between the microstructures of carbon and alloy steels and cast irons and their damping capacities (ability to absorb vibration). Researchers measured damping capacity and other properties and investigated the effects of carburizing, spheroidizing, and annealing. The investigators found that in carbon and alloy steels, rounded colonies of fine-grained pearlite in a ferrite matrix correlate well with low damping capacity. Steel microstructures that exhibit sharp-faceted pearlite in ferrite matrix and partially or fully spheroidized cementite in ferrite show considerably higher damping. In cast irons, the lowest damping capacity is associated with nodular graphite microstructure, and the specific damping capacity (SDC) increases as the graphite micro-structure progresses from nodular to compacted to flake. Predominant ferrite in cast irons is also associated with good damping. SDC data are presented for selected carbon and alloy steels and cast irons.

Jan 1, 1987

By I. Liebman

Two triggered barrier systems and several extinguishing agents were tested against coal dust explosion propagating in the main entry of the Bureau of Mines Experimental Mine at Bruceton, Pa. One system used a high-pressure cylinder to propel the extinguishant; the second system used pressurized nitro-gas or Halon 1301 (CF3Br) in a low-pressure system to power the disperser. The relative efficiencies of the extinguishants were determined by compar¬ing calculated concentrations of the extinguishant clouds present in the mine during suppressing of the explosions. Results showed the following trend of increasing effectiveness: Purple-K (KHC03)<water<hybrids consisting of foam or water combined with Halon 1301<Halon alone. On a weight basis, water was two to three times as efficient as Purple-K, whereas the hybrids and Halon alone were only marginally superior to water. Maximum efficiency of an extinguishant is attained by high rates of discharge from the barrier and by minimizing the time interval between onset of discharge and flame arrival to that necessary for discharge. Both the high- and low-pressure barrier systems were demonstrated to be capable of suppressing coal dust explosions; however, because of the potential hazard of the former, the low-pressure system is considered to be the most attractive prototype.

Jan 1, 1979

By G. G. Morgis

In carrying out the provisions as set forth by an Act of Congress (36 Stat. 369) approved May 16, 1910, effective July 1, 1910, and the amended Act of February 25, 1913, (37 Stat. 681), the Bureau of Mines, among other activities, conducts inquiries and scientific and technologic investigations concerning mining with a view to improving health conditions and increasing safety and disseminates the general information gained by these studies. Through the medium of these publications, the causes as well as the methods that have been found most satisfactory in combating undesirable conditions are brought to the attention of the mining industry. This bulletin describes health and safety reports that have been published for the period July 1, 1955, through June 30, 1961. Technical Paper 705 issued in 1948 contains a listing of all Bureau of Mines publications dealing with health and safety in the mineral and allied industries from 1910 through 1946; Bulletin 558 contains a bibliography of such reports that were issued from January 1947 through June 1955.

Jan 1, 1962

By William A. Beck

The Construction Aggregates Corp. operates a plant for processing sand and gravel from two deposits in Ottawa County, Mich. The bulk of the sand is obtained from a sand dune on the shore of Lake Michigan, and the gravel is dug from a glacial-drift deposit farther inland. Mining is done with draglines, and the material, both at the digging site and in the plant, is moved mainly by systems of conveyors. The Ferrysburg plant serves customers along the Great Lakes, which is unusual for a business normally local in character. Annual production exceeds 1-1/2 million tons of sand and gravel as concrete aggregate and 200,000 tons of core sand for foundry use.

Jan 1, 1962

By L. G. Marshall

This report describes dredging and processing of sand and gravel from a glacial-fluvial deposit in the Raccoon River valley near West Des Moines, Iowa. Preliminary cleaning and separation of the sand and gravel at the dredge site with subsequent transportation to separate plants and the production and disposal of the various grades of aggregate material are also described. The geology of the deposit is summarized. A tabulated summary of costs in units of labor, power, and supplies is included.

Jan 1, 1963

By Donald W. Baggs

This report describes economic mining feasibility studies conducted by the Bureau of Mines to estimate mining costs in the Porcupine mining area of the Juneau Mining District, southeastern Alaska. Investigations were conducted on the economics of three mineral deposit types: 1) massive sulfide deposits containing zinc, copper, and silver, 2) vein gold, and 3)disseminated gold. Cost estimates were developed using the Bureau of mines Cost Estimating S,-stem. Discounted cash flow rates of return were calculated using the Bureau of Mines MINSIM (mining simulation) computer program. Three sets of metal prices were used in the study based on recent historical price information. Underground longhole stope mining of a massive sulfide deposit containing 25 pct zinc. 1 pct copper, and 63.6 g/mt silver was found to be economic at high metal prices at a quantity of 13,200,000 mt ore. Cut-and-fill mining of a 26,400,000 mt massive sulfide deposit was found to be economic at medium metal prices. Open pit mining of a similar deposit was found to he economic at medium metal prices and 26,400,000 mt ore, or at high metal prices and 6,600,000 mt ore. Underground mining of a vein gold deposit was found to be economic at a grade of 17.1 g/mt medium metal prices and 1,320,000 mt ore. Open pit mining of a disseminated gold deposit was found to be economic at a grade of 1.71 g/mt medium metal prices and a quantity of 39,600,000 mt ore.

Jan 1, 1986

More than 400 academic, Government, and industry representatives attended the third symposium on ash utilization and technology held in Pittsburgh, Pa., March 13-14, 1973. Sponsored by the American Public Power Association, Edison Electric Institute, National Coal Association, National Ash Association, and Bureau of Mines, the symposium Featured 26 formal presentations by leading experts from Europe and the United States on all major phases of ash production, utilization, and research. Abstracts of all the papers are grouped right after this introduction, and the full symposium proceedings follow. Sponsoring organizations and their chief representatives were the National Coal Association, James R. Garvey, Bituminous Coal Research, Inc.; Edison Electric Institute, C. E. Brackett, Southern Electric Generating Co.; American Public Power Association, Herbert Blinder, Columbus (Ohio) Electricity Division; National Ash Association, Inc., James N. Covey, Rochester Gas and Electric Corp.; and the United States Department of the Interior, Bureau of Mines, William L. Crentz.

Jan 1, 1974

By Agnes Y. Lee

As part of the U.S. Bureau of Mines program to improve base metal leach systems, pressure leaching of galena (PbS) concentrates in fluosilicic acid (H2SiF6) solution was investigated. Lead extraction was 93 pct when PbS was pressure leached in H2SiF6 at 95° C with 2OO-psig O2 pressure for 40 min, using ferric nitrate [Fe(N03)3] as a catalyst. The effects of several catalysts, O2 pressure, time, and acid concentration on leaching were determined. The purified leach solution was electrowon to recover high-purity Pb metal. The H2SiF6 used in leaching and electrowinning can be recycled continuously. A flow diagram was proposed based on this investigation. Elemental sulfur (SO) was recovered from the leach residue by solvent extraction. A method was also developed for treating the flnal residue to segregate the important byproduct elements such as Ag, Cu, and Zn and enable their recovery by standard commercial processes.

Jan 1, 1990

By T. E. Swigart, C. E. Beecher

The Federal Government, as the largest lessor of oil and gas lands in the United States, is vitally interested in the conservation of those resources. This manual has been prepared at the direction of the Secretary of the Interior to call the attention of lessees of public oil and gas lands to the most common oil and gas field wastes and the best methods of preventing them; to outline the policies of the Interior Department on field operations; and to give information as to how the "Operating Regulations" of the department will be interpreted by the Bureau of Mines. The oil industry has progressed steadily. Present operating methods are much more efficient-and less wasteful-than those of a few years ago; moreover, the art of producing oil and gas is continually advancing. Public interest requires that improved methods, which will result in obtaining the greatest possible amounts of oil and gas from the natural deposits, shall be developed and used. Part I of this manual points out types of oil and gas wastes and suggests, in detail or by reference, the most practical and effective methods in current practice for stopping these wastes. Throughout Part I the department's operating policy is given, with interpretations of the "Operating Regulations" for enforcing every practical measure of conservation. Part II comprises the revised "Operating Regula-tions" which supersede all previous regulations and will govern future operations on public lands; it will be found in the pocket in the back cover of this bulletin.

Jan 1, 1923

By H. M. Smith

MORE than a year before the United States entered World War II, the requirements of the National Defense Program indicated the need for additional sources of aviation gasoline. On September 10, 1940, Dr. R. E. Wilson, Group Executive, Advisory Commission of the Council for National Defense, requested the Bureau of Mines to undertake a survey of crude oils of the United States to designate those suitable for the production of 91-octane aviation gasoline. As quickly as a program could be defined, agreed upon, and funds provided to conduct the work, the Bureau began the project. Over a period of many years the Bureau had collected samples and made analyses of thousands of crude oils produced in the United States. Although these analyses did not include octane numbers of the gasoline fraction, they provided data necessary for calculating the correlation index. This index, developed within the Bureau, is a measure of the types of hydrocarbons present in gasoline and therefore is roughly indicative of the octane value. This fund of information from Bureau of Mines Hempel analyses, supplemented by information obtained from oil companies, reduced considerably the necessary laboratory work by providing data that permitted a large number of crude oils to be eliminated from consideration. However, in the survey carried out during the last part of 1940 and the first half of 1941, 225 samples of crude oil were collected and distilled. Octane values of the distillates were determined by the Army AFD-1C method. (See page 57.) A report containing these results, together with the calculated amounts of 91-octane aviation gasoline available from these sources, was prepared and distributed to the several offices of the Office of the Petroleum Coordinator for National Defense in August 1941. In December 1942 the Office of the Petroleum Coordinator for National Defense became the Petroleum Administration for War (P. A. W.).

Jan 1, 1951

By James E. Cairelli

The NASA Lewis Research Center, under U.S. Bureau of Mines program direction, performed an assessment of alternative mobile power sources for mining applications. A wide variety of heat engines and energy systems was initially examined to ascertain which could be considered as potential alternatives to presently used power systems. The present mobile power systems are electrical trailing cable, electrical battery, and diesel - with diesel being largely limited in the United States to noncoal mines. Each candidate power source was evaluated in terms, of the following requirements: (1) Ability to achieve the duty cycle (2) Ability to meet Government regulations (MSHA certification) (3) Availability (production readiness) (4) Market availability (5) Packaging capability An initial screening reduced the list of candidates to the following: (1) Diesel (2) Stirling (3) Gas turbine (4) Rankine (steam) (5) Advanced electric (batteries) (6) Mechanical energy storage (flywheel) (7) Use of hydrogen evolved from metal hydrides This list of candidates was divided into two classes of alternative power sources for mining applications - heat engines and energy storage systems. A summary of each class follows.

Jan 1, 1981

By Alfred V. C. Meyer

A Blastcorder4 was calibrated on the Bureau of Mines shaking table in the frequency range of 12 to 40 c.p.s. and in the amplitude range&apos; of 0.25 to 1.0 g. The results of this calibration study show that in the frequency range of 12 to 30 c.p.s. the average accuracy of the Blastcorder is approximately ± 0.1 g.

Jan 1, 1962

1. Domestic Production and Use: In 1984, 12 companies operated 27 primary aluminum reduction plants, with 3 firms accounting for 57% of production. Washington, Oregon, and Montana accounted for 35% of the production; Indiana, Kentucky, Missouri, and Tennessee 25%; Alabama, Arkansas, Texas, South Carolina, and North Carolina 20%; other States 20%. Based on published producer prices, output of primary metal in 1984 was valued at $7.2 billion. Aluminum consumption by 25,000 firms was centered in the east-central United States. Packaging accounted for an estimated 35% of domestic consumption in 1984, transportation, 20%; building, 18%; electrical, 9%; consumer durables, 8%; and other uses, 10%.

Jan 1, 1985

By H. S. Benson

This report documents, from concept through field testing, the pan scraper Wheel Slip Monitor. The function of this device is to instantly warn the scraper operator of wheel slip and thus enable him to take immediate corrective action. Knowledgeable pan scraper people recognize that the preponderance of scraper tire damage and wear occurs during useless wheel slip when the scraper operator attempts to increase machine draft beyond what traction will allow. The resultant shortened tire life has become very expensive. The Wheel Slip Monitor reported here provides the means for relieving the scraper operator of attempting to judge wheel slip on tires he cannot see. Direct and intuitively understandable audible and flashing light warnings tell the scraper operator which wheel is slipping and also indicate the relative magnitude of the slip. Beside the Wheel Slip Monitor&apos;s patent utility as a real time operator aid, it has unique potential for application to extended term wheel slip history acquisition under field conditions. This information has never been easily available and it promises practical value in pan scraper management.

Jan 1, 1983

By Sam S. Taylor

The disposal of oil-field brines by injection into subsurface formations other than fresh-water-bearing strata is a positive method of eliminating the harmful effects of mineralized water on fresh-water supplies, vegetation, and aquatic and other animal life. The methods used most generally for the disposal of brines produced with oil are (1) impounding in evaporation ponds, (2) controlled diversion into surface streams, and (3) injection into subsurface formations. Various States recognize one or more of the methods as legally authorized procedure. As a general rule, impounding brine in ponds and solar evaporation have not been entirely successful, principally because of the large volumes handled; the porous nature of the soil, and the low rate of evaporation. Likewise, the diversion of brine into freshwater streams by controlled dilution has not proved satisfactory in some areas, especially in parts of Kansas and Oklahoma where the rainfall is relatively low, because it has been impossible to obtain enough fresh water for such dilution.

Jan 1, 1939

By E. D. Calvert

The room temperature tensile properties of commercially pure titanium and seven titanium alloys prepared by skull casting were determined in the as-cast and heat-treated conditions. Data were compared with property data from tensile tests on wrought alloys of the same compositions in the as-worked and heat-treated conditions. The alloys evaluated were Ti-5Al-2.5Sn, Ti-6Al-4V, Ti-6Al-4V-lSi, Ti-6A1-2Sn-4Zr-2Mo, Ti-6A1-6V-4Zr-4Mo, Ti-6A1-6V-2Sn, and Ti-11.5Mo-6Zr-4.5Sn. Test specimens were prepared from both static and centrifugal castings and from plate fabricated by forging and rolling vacuum-melted ingots. The data indicate that the alpha and alpha-beta alloys have strength properties in the as-cast condition that are reasonably close to the strength properties of their wrought counterparts in the as-worked condition. An exception to this was the Ti-6A1-6V-4Zr-4Mo alloy for which insufficient data were available to form any firm conclusions. Fine-grained cast structures of Beta III (Ti-11.5Mo-6Zr-4.5Sn) were shown to be generally stronger in the as-cast condition than the wrought alloy in the as-worked condition except for the yield strength of one structure that was unusually low. Heat treatment of this alloy produced properties that were unpredictable. Indications are, however, that optimization of heat treatment parameters for each cast structure could produce strength properties equal to that of wrought materials.

Jan 1, 1974

By Albert L. Toenges

A phase in strip mining of bituminous coal is the overturning of the surface of the land. The ;purpose of this report is to acquaint the operators and others interested in stripping with the work that has been done in certain States to reclaim the surface of land from which the coal has been removed by this method of mining. The preparation of this manuscript follows an extensive study of the subject in the field in the course of which a large number of strip mines were visited. ACKNOWLEDGMENTS The information used in the report was obtained through the courtesy and cooperation of the operators of the mines visited, State officials and educational institutions, and others interested in the subject.

Jan 1, 1939

By Alan Mayton, Bertrand Valero, Christopher Jobes, Farid Amirouche

Exposure to vibration induced in and around underground mine’s exploration is a major concern to vehicles operators. Most of these drivers over time develop serious spinal musculoskeletal and discs problems causing low back injuries. The first purpose of this paper is to analyze the performance and dynamic response of driver/operator when subjected to different levels of vibration due to rough road conditions depicted in a mine field. The second purpose of the paper is to quantify the energy transmission in the presence of seat padding with special characteristics and active suspension. Using experimental testing data collected at NIOSH/PRL (National Institute for Occupational Safety and Health/ Pittsburgh Research Laboratory) along with model simulation algorithms developed at the University of Illinois at Chicago we investigated how acceleration transfer functions as well as absorbed power affects the different parts of the body. To this end, we used a previously validated human model which includes the head, torso segments and legs. The connective forces between body segments were modeled through modal analysis techniques from previous experimental data at the UIC Vehicle Technology Laboratory. The absorbed power and energy transmitted to the body are used as an index measure to assess the viability of the different seat padding’s and active seat suspension control strategies.

By R. H. Church, William E. Webb, Walter E. Pittman, James R. Boyle

As part of the Bureau of Mines health and safety research program, a short-range locator system, capable of locating miners who have become trapped following a mine accident, has been devised, The system consists of a lightweight, low-power radio transmitter incorporated into a miner&apos;s cap lamp battery and a directional receiver carried by rescuers. Prototype transmitters have been constructed, and the propagation of their signals has been investigated, The detectability of the signal in underground coal mines has also been investigated, This research indicates that a short-range location system would serve as an economical and practical means of locating miners from within the mine following an accident,

Jan 1, 1984

Illumination hardware developed in conjunction with previous Contracts H024202l, H0242049, and H0242023 had not been adequately tested in actual underground work situations. The purpose of this contract was to install and monitor this equipment on mining machines and in actual working places of coal mines to gain experience with the use of the lamps and support equipment in the abusive and critical environments for which they were intended. The equipment that was to be tested consisted of the following: a. Lamps -A variety of sizes of permissible fluorescent lamps which operate from 12 volts DC power. These include the following sizes: Model 8, (9 watts) 2" diameter; Model 15/2 (14 watts) 2" diameter; Model 15/3 (21 watts) 3" diameter; Model 20 (25 watts) 3" diameter; Model 30, (28 watts) 3" diameter; and Model 40, (39 watts) 311 diameter. Representative photographs of these lamps are shown in Figure 1-1 and 1-2.

Jan 1, 1976