Search Documents

By Theodore Kootz

Manufacture of high-grade ferromanganese; as a rule; requires a low-phosphorus-manganese ore with 45 to 55 percent Mn, chiefly obtained in the Soviet Union, the British Dominions, and Brazil. Also, low-manganese ores have already been used for ferromanganese production, especially in North America .and Germany. During World War I, a process was developed in which a high-phosphorus ferromanganese or spiegeleisen was prepared in the blast furnace from law- or high-phosphorus manganiferous ores, then low-phosphorus manganese slag was prepared by refining under an acid slag, and this material was, worked into a low-phosphorus ferromanganese in the blast furnace.9/ Manufacture of useful manganese ores from a phosphorus-bearing spiegel with 12 to. 15 percent Mn, 4.5 percent C,, and 0.5 percent P by slagging in a refining furnace was reported by Joseph, Barrett, and Wood.10/ The spiegel was refined to 0.75 percent Mn, 3.4 percent C, and 0.45 percent P. Thereby, a slag with about 43 to 58 percent Mn and, about 10 percent Si02, was obtained. Hotter melts gave a smaller phosphorus content in the slag than cold melts. In addition, the phosphorus content of the slag varied with the manganese content of the intermediate metal.

Jan 1, 1952

By Carl Rampacek

Recent research by the Bureau of Mines has demonstrated that the segregation process has merit for treating oxidized and mixed oxide-sulfide copper ores. The process comprises heating the crushed ore with salt and coke or other carbonaceous materials at about 700° C. to produce fine flake copper, which then is recovered by conventional copper-flotation methods. Bench-scale laboratory tests of a number of oxidized and mixed copper ores assaying 0.78 to 5 percent Cu gave copper recoveries of 73 to 96 percent. The flotation concentrates assayed 21 to 76 percent Cu, depending on the ore being treated.

Jan 1, 1959

By R. Craig Smith

The Bureau of Mines conducted a study of production costs for the secondary lead industry and determined costs for present, pending, and proposed environmental legislation. Operating costs for smelters by capacity groups range from 16.8 to 19.6 ¢!lb of refined lead. Present regulatory compliance costs for these groups range from 2.2 to 2.4 ¢!lb. Pending compliance costs could add 3.5 ¢!lb of refined lead, and proposed regulations could add another 1.3 ¢!lb. The individual capital costs necessary to comply with pending environmental regulations are estimated to be $1.8 million for small smelters and $10.4 million for large smelters. Proposed regulations could require additional expenditures from $1.9 million for small smelters to $4.9 million for large smelters. These cost estimates, based on average 1985 dollars, indicate that pending and proposed legislation could add significantly to capital and operating costs of the secondary lead industry. These regulatory compliance costs may result in a loss of up to 40 pet of secondary lead production capacity.

Jan 1, 1987

By J. W. Paul

Withdrawing timber in coal mines is done for the purpose of inducing the roof to cave in the mined-out areas and thereby relieve stresses in the immediate roof material over the working places adjacent to the breakline of the roof, thus preventing the crushing of the ends of pillars and adding to the safety of those engaged in pillar extraction. A secondary purpose is the recovery of timber for further use either as prop-, crossbars, lagging, sprags or cap pieces. At some mines timber is withdrawn as a precaution against fire which may he of spontaneous origin, because wood always aids a fire of any origin. With some of the power-driven types of machines now in use a greater proportion of mine timber may be recovered, and in mines where pillars are left too narrow for their removal some of the timber in rooms might be salvaged for further use.

Jan 1, 1933

By Guy E. Dent, Robert S. Sandford, W. T. Millar, Hugo E. Kuehn

"INTRODUCTION AND SUMMARYDuring the latter part of 1943 a magnetometric survey was conducted by the Geophysical Division of the Bureau of Mines at the mine, Putnam County, N. Y., in an endeavor to locate a segment of the body that reports state was cut off by a fault. The Mahepac mine was abandoned about 1895 after producing nearly 1,000,000 tons of high-grade magetite iron ore. The results of the investigation indicate the termination of the ore body by ""pinching"" or a displacement of such magnitude as to place any extension at a considerable distance the original ore body. This report describes the work done on the project and presents the data obtained. ACKNOWLEDGMENTSThe Bureau of Mines has been investigating deposits of critical and essential minerals in the United States and Alaska since 1939. The Mahopac mine was visited by W.T. Millar, an engineer of the Bureau of Mines, on June 5, 1943, accompanied by Dr. William Agar of the Federal Survey, and again on July 29, 1943, accompanied by Dr. A. F. Buddington and H.F. Hawkes, both of the Geological Survey.The mineral investigation was under the general supervision of Paul M. Tyler, formerly regional engineer, Eastern Region; J. D. Bardill, formerly district engineer; and Dr. F.W. Lee, formerly chief. Division, Geophysical Exploration. The work was done under the immediate supervision of W. T. Millar, project engineer. The Geophysical Survey was made by Hugo Kuehn and Guy E. Dent."

Sep 1, 1948

By William J. Campbell

The Federal Bureau of Mines provided five test materials--amosite, short-and long-fiber chrysotile, crocidolite, and nonfibrous tremolite--to the National Institute of Environmental Health Sciences (NIEHS) for studies on the biological effects of orally ingested asbestos-related materials. An inter-agency agreement between the Bureau and NIEHS made possible this program to characterize these test materials. The Bureau in turn received support through contracts with the Ontario Research Foundation for the milling of amosite and crocidolite, and with the University of Maryland for microscopic measurements. The five test materials, which were supplied in quantities of 960 to 1,200 pounds each, were characterized by chemical-instrumental analysis for elemental composition, surface area, density, X-ray diffraction, infrared spectroscopy, thermogravimetric analysis, mineralogy, and particle size analyses. Particle size distributions were emphasized because of the current theories relating adverse biological effects to length-width characteristics of durable elongated particles.

Jan 1, 1980

Mainland China To Pay Japanese Company On Contract Claim. - Mitsubishi will receive $39 million from Red China, half of what was asked, for China's having, curtailed work on a 5369 million steel rolling mill at Baoshan near Shanghai. Copper Found in Chile. - Utah International Inc., in conjunction with Getty Oil Co., has discovered a cooper deposit in northern Chile. Early drilling reveals an enriched zone grading 1.2% to 2 3% copper. Chile already has tie world's largest Cu reserve base. Soviets To Aid Laotian Tin Industry. - The U.S.S.R. has agreed to help strengthen the tin industry in Laos, a client state. In the past, Laos has only produced small amounts of tin concentrate, 500 tons to 1,000 tons per year presumably shipped to smelters in Singapore or Penang, Malaysia. Under the agreement made in June, the Soviets are to supply equipment to increase the out put of tin from the Phontieu, Neng, and Nongsen mines and help Laos with the construction of a tin smelter. The U.S.S.R. itself is a net importer of tin, although a substantial producer of the metal.

Jan 1, 1981

By L. A. Neumeier

The Bureau of Mines evaluated the properties and anisotropy in properties of rolled Zn-Ti and Zn-1.0 wt pct Cu-Ti alloys containing up to 0.36 wt pct Ti. Finish rolling was at varied temperatures to total reductions as high as 92 pct. Alloy properties are very sensitive to various combinations of composition, rolling temperature, and reduction. Properly rolled Zn-1.0 Cu-Ti alloys are superior in strength to Zn-Ti alloys. Conditions are described that lead to best tensile properties. Creep resistance for Zn-Ti alloys decreases with increased rolling temperature when finish rolled to 92-pct total reduction: but not when finish rolled to 33- or 67-pct reduction. Creep resistance for 7n-1.0 Cu-Ti alloys improves with increased rolling temperature to about 480° F. Heavily cold-rolled Zn-1.0 Cu-Ti alloys have fine grain sizes and poor hardness, tensile, and creep properties, but high ductility. Thermal expansivity is markedly affected by the copper addition. Data show the anisotropy of tensile, creep, and thermal expansivity properties. Large idiomorphic crystallites of TiZn15 appear in both Zn-Ti and Zn-Cu-Ti alloys when more than about 0.2 pct Ti is present. A new Zn-Cu-Ti intermediate phase was also identified. Empirical equations are presented relating creep rates with major process variables.

Jan 1, 1971

By Barry W. Klein

The performance of the U.S. economy in 1977 was similar to that in 1976 which, in turn, had been a considerable improvement over 1974-75. In 1977 real gross national product (GNP) showed a similar, but some-what slower, growth pattern compared with 1976. Real GNP increased sharply in the first quarter of the year followed by smaller increases for the remaining three quarters. With only two exceptions, the monthly unemployment rate declined or remained steady throughout 1977, falling to a low for the year in December. The inflation rate in 1977 was slightly higher than in 1976, but the rate still remained far below that of 1974-75. Total U.S. output as measured by GNP in current dollars rose 10.8% in 1977. Real GNP in constant 1972 dollars increased 4.9%, and inflation, as measured by the implicit price deflator, rose 5.6%. In real terms, gross private domestic investment for residential structures increased 19.3% in 1977, only slightly below the 22.9% rise in 1976; State and local government expenditures increased 1.1 % in 1977; and personal consumption expenditures for services rose 4.5%.

Jan 1, 1980

By Allen D. Look

In the prevention of accidents in milling operations, the proper installation and guarding of electrical and mechanical equipment, safe clearances, good housekeeping, adequate fire protection, adequate ventilation, dust and fume control, and good illumination, as well as safe practices, are essential. In the new concentrator of the Magna Copper Co., Superior, Ariz., many safeguards were incorporated and safe practices instituted to minimize accident hazards. The purpose of this paper is to describe some of these features and practices.

Jan 1, 1951

This Bureau of Mines report on underground mine communications addresses methods and equipment to meet the communication requirements of working sections and places of coal and metal-nonmetal mines. A review of the status of trapped miner detection is also presented.

Jan 1, 1977

Exposure to airborne respirable crystalline silica dust can lead to silicosis, a debilitating lung disease. On surface coal mining and construction sites, blast hole drills are notorious sources of airborne respirable dust that may contain significant amounts of silica. The drill operator and drill helper usually receive the greatest silica exposure compared with other occupations. As a result, many drilling operations have been, and still are, on more stringent dust standards. Drilling through various rock formations naturally presents a strong potential for silica dust generation for several reasons. First, drilling is a pulverizing process that generates large amounts of very small dust particles. Second, the bailing air used to flush cuttings from the hole leaves the hole at a very high velocity and can be difficult to contain. Third, many fixed shrouds used to enclose the area beneath the drill deck have a significant amount of leakage due to 1) gaps between the shroud and ground created by raising/leveling the drill, 2) gaps in the corner seams, and 3) tom deck shrouds. CONTROLS A dry dust collection system is typically connected to the drill deck to collect dust as the bailing airflow transports the cuttings (and significant amounts of airborne respirable dust) out of the drill hole. Deck shrouds are installed in an attempt to enclose the volume around the drill steel and prevent dust escaping. However, most deck shrouds are rectangular and constructed of four separate pieces of rubber belting attached to the deck. Because of this design, there is usually a significant amount of dust escaping from the open seams as well as the open area between the shroud and the ground. This dust can be a significant source of silica exposure to drill operators as well as other personnel downwind of the drill.

By Terry S. Cory

This report describes a complete system design methodology for medium frequency (MF) wireless radio systems for use in coal mines. The emphasis Is on AC mines where no trolley wire exists and, for which, conventional trolley phone communications can not be used. The report constitutes an MF system design handbook and includes a compendium of all previous MF technology elements as well as a reference index with abstracts of all pertinent literature. A particular strawman system design analysis is included for the Helvetia Coal Co. Lucerne #8 mine in the Upper Freeport seam.

Jan 7, 1979

"A coordinated, integrated research effort aimed at studying the scientific, engineering and medical aspects of the respirable dust problem is underway in the areas of dust generation, dust dispersion and dilution, dust characterization, interaction of dust and lungs, and relationship of seam characteristics to dust generation and mobility. (FIGURE 24) The Center's research program explores these concerns with the objective of refining existing strategies and developing new respirable dust control techniques that are consistent with the dust-lung interaction processes that lead to mine worker disability. The fundamental aspects of this work are applicable to the control of respirable dust problems in both hard rock mines and coal mines and to other dusts such as diesel-generated.Research projects in the Generic Mineral Technology Center for Respirable Dust have effected several improved methods for the preparation and characterization of the dusts needed by these projects. Superior procedures for generating ""standard"" dust samples have been developed and are in regular use in the laboratory. Questions raised during the course of some projects regarding ""stale"" versus ""fresh"" dust have led to the development of sampling techniques where the dust is directly collected in a surfactant. MSHA and CANMET have requested and received information on Center generated software. An equipment manufacturer, TSI, Inc., requesting input on modifying the inlet of an aerosol sampler has been assisted as a result of research that was conducted at the University of Minnesota.The objectives, scope and progress of all the research projects in the Center, in the form of abstracts and reports, have been detailed in Volume 1 of this series. Research papers written by the principle investigators and resulting from the findings of projects (FIGURE 25) and which are funded by U.S. Bureau of Mines grant number G1135142 have been published in Volumes 3 through 6 and Volume 8 of this series. Volume 2 relates the cooperation and interaction of the U.S. Bureau of Mines and the Generic Mineral Technology Center for Respirable Dust in research on the problem of respirable dust in the mineral industries."

Aug 31, 1989

By W. P. Diamond

It is estimated that more than 1 trillion cubic feet of methane is contained within the coals of the Mary Lee group in Jefferson, eastern Tuscaloosa, and southern Walker Counties, Ala. Most of this methane will be encountered by mining. Coals of the Mary Lee group are presently being mined at depths exceeding 1,000 feet and will in the near future be mined at even greater depths, where the problem of methane gas affecting the mining operations will be acute. It is calculated that approximately 90 pct of the methane is at depths greater than 1,000 feet, and over half of the gas is contained within only 12 pct of the study area which is under more than 1,500 feet of over-burden. Degasification in advance of mining will increase mine safety, reduce ventilation expenditures, increase productivity, provide an additional energy source, and make it possible to mine parts of deep coalbeds that probably could not otherwise be mined.

Jan 1, 1976

The Technology Transfer Seminar on Mine Communications held on March 21-22, 1973, at the Pittsburgh Mining and Safety Research Center, Bruceton, Pa., presented information about recently developed equipment, instruments, and techniques for use in mine communications systems. All of the basic ideas presented in the fine seminar are operational in the Bureau of Mines Safety Research Mine in Bruceton.

Jan 1, 1974

"The U.S. Bureau of Mines established on August 15, 1983, The Generic Mineral Technology Center for Respirable Dust (Dust Center) within the Mining and Mineral Resource Research Institutes (MRIs) at The Pennsylvania State University and West Virginia University, and in association with participating MRIs at Massachusetts Institute of Technology and the University of Minnesota. In 1986, Michigan Technological University (MTU) was awarded a grant through the Dust Center. The center's research program has been developed with recognition of the stated objective of the Federal Mine Safety and Health law, which is ""... (to) permit each miner the opportunity to work underground during the period of his entire adult working life without incurring any disability from pneumoconiosis of any other occupation-related diseases..."" The Dust Center's program is designed to foster an accelerated attack through fundamental research on problems confronting the control of respirable dust in mines. The interactions of the universities and the research program components in the characterization of coal seams, respirable dust particles and the workers lungs are depicted in the logo of the Dust Center.The primary goal of the Dust Center is to reduce the incidence and severity of respirable dust disease through advancing fundamental understanding of all aspects of respirable dust associated with mining and milling, and the interaction of dust and lungs. The Dust Center's research program explores these concerns with the objective of refining existing strategies and developing new respirable dust control techniques that are consistent with the fundamental dust-lung interaction processes that lead to mine worker disability. The work concentrates on: (1) control of dust generation; (2) dilution, dispersion and collection of dust in mine airways; (3) characterization of dust particles; (4) interaction of dust and lungs; and (5) the relationship of the mine environment, geology, and seam characteristics to dust generation and mobility. The fundamental aspects of this work are applicable to the control of respirable dust problems in both hard rock mines and coal mines, and to other dusts such as those generated by diesel equipment. Achieving the Dust Center's goals also involves the training of engineers and scientists, graduate students, and undergraduate students through their respective institutions, and technology transfer to industry. The distribution of personnel in the various universities are presented in Table 1. A directory of Dust Center principal investigators is presented in Appendix 1. A summary of degrees granted and mineral sector employment is presented in Table 2. The subjects of theses developed under the various research projects are presented separately in Volume 7. The center research is fully compatible and complementary with the existing and ongoing U.S. Bureau of Mines activities (see Volume 2). Additionally, the expertise and facilities of the NIOSH--Division of Respirable Disease studies are available as a result of the existing relationship between NIOSH and West Virginia University. Figure 1, Respirable Dust Center Projects and Activities, presents the various projects in the five major areas of investigation and the scope of characterized dust samples, the suite of tests, the sampling and dust generation methods, and the size, chemical and mineralogical analysis performed in the center. Table 3 presents a summary distribution of the 95 publications and presentations that have emanated from the center. In addition there are more than thirty presentations made at each annual Dust Center review meeting. The titles, authors and location of presentation for publications supported by the Dust Center are presented in separate publication volumes for 1984 (Volume 3), 1985 (Volume 4), 1986 (Volume 5) and 1987 (Volume 6)."

Jan 1, 1988

By D. R. Flinn

The Bureau of Mines has studied the electrochemical parameters important to the preparation of coatings of the platinum-group metals. Using molten mixtures of sodium and potassium cyanides in an inert atmosphere, techniques have been developed that permit the preparation of baths for platinum, rhodium, and iridium electrodeposition. Cyclic voltammetric and slow sweep rate linear polarization techniques have been utilized to determine optimum potential and current values for preparation of plating baths and for the electrodeposition of coatings. Techniques are described for the deposition of platinum and rhodium coatings at near 100 percent anode and cathode current efficiencies, and for iridium at approximately 80-percent efficiency. Palladium deposition from these molten cyanide baths remains un-satisfactory. The chemistry of the palladium-containing cyanide bath is discussed. Examples of scanning electron microscope photomicrographs of typical platinum coatings are presented. Techniques are described for the preparation of platinum coatings on large objects.

Jan 1, 1982

By H. F. Weaver

The 18th National First-Aid and Mine Rescue Contest was held in the Memorial Auditorium, Buffalo, New Vork, October 5, 6, and 7, 1959. The meet was sponsored by the Federal Bureau of Mines and the Joseph A. Holmes Safety Association, in cooperation with State mine inspection agencies, management and labor of the mineral extractive industries, and other safety minded groups. The Arrangements Committee, as authorized by the General Committee, made a11 the necessary arrangements for conducting the 1959 contest. Members of the Arrangements Committee were: Harry Gandy, Jr. (chairman), National Coal Association; James B. Benson, Southern Coal Producers' Association; Charles Ferguson, United Mine Workers of America; George C. Trevorrow, Bituminous Coal Operators' Association; and James Westfield, Federal Bureau of Mines.

Jan 1, 1960

By T. T. Campbell

A survey of the literature eras made covering the use of aqueous non-aqueous, and fused-welt systems for the electrowinning or electroplating of molybdenum metal. The survey was prepared in order to provide background for further investigations directed toward the electrodeposition of pure molybdenum metal from either aqueous or nonaqueous mediums. While a thorough effort was made to cover all available references, a critical review was not attempted nor does this survey pretend to be exhaustive in nature.

Jan 1, 1955