Search Documents

By R. V. Ramani, R. Bhaskar

"The spatial distribution of airborne dusts, deposition of dust in the airway, as well as the effect of airflow velocity and particle density on dust behavior in mine airways were studied in a set of experiments performed in a mine airway under controlled conditions. Considerable deposition of dust near the source was indicated. Pronounced effects due to velocity were observed in ambient dust concentration and deposition along the mine airway, both in the respirable and the total size ranges. Cross-sectional concentration measurements indicate an increase in concentration from the roof to the floor. The average cross-sectional concentration is about 75% of the concentration in the center of the airway.IntroductionA number of studies have been performed since the early 1950s on the behavior of dust in mine air (Bradshaw and Godbert, 1954; Dawes and Slack, 1954; Bradshaw et al., 1954; Hall, 1955-56; Reinhardt, 1971; Ford, 1971; Courtney et al., 1982). While the experimental data available from these studies are indeed useful in understanding dust cloud behavior in a specific situation, no generalized conclusions can be drawn because of the lack of data on parameters such as flow velocity, size distribution of the source dust, and particle density. These change from mine to mine or even within the same mine. The present study is aimed at providing a better understanding of the temporal and spatial behavior of dust particles in underground mine airways (National Academy ofSciences, 1980). The characteristics studied encompassed airborne concentrations and floor depositions over the entire size range as well as the respirable size range. The experimental results in this paper are intended to complement a mathematical model developed to predict ambient concentration and deposition of airborne dust in mine airways (Bhaskar and Ramani, 1986)."

Mar 1, 1989

By W. L. Dare

This information circular is one of a series published by the Federal Bureau of Mines in which the methods and costs of producing uranium ore on the Colorado Plateau are discussed. This report describes the three largest company-operated uranium mines of Climax Uranium Co. - the G-1, the Mineral Joe, and the Frank No. 1. Climax Uranium Co., a subsidiary of American Metal Climax, Inc., was [corporated] May 11, 1950, just 2 years after establishment of the domestic uranium program by the Atomic Energy Commission. Twenty-five years earlier Arthur H. Bunker, now chairman of the board, American Metal Climax, Inc., organized and operated the U. S. Vanadium Co. at Rifle, Colo.3/ Soon after Climax Uranium Co. was organized, it entered into a contract with the Federal Government to build a uranium-vanadium processing mill in Grand Junction, Colo. Under the contract Climax leased from the Federal Government certain uranium-bearing lands that had been withdrawn from public entry in 1948. From Minerals, Engineering Co. on June 12, 1950, Climax acquired other uranium-vanadium properties on Calamity, Outlaw, and Monogram Mesas in Colorado and on Polar Mesa and in the Yellow Cat area of Utah. To house the milling equipment, Climax leased the old Grand Junction sugarmill building of the Holly Sugar Co. Milling facilities, based on a then new process developed for treating both uranium and vanadium, were completed, and the plant went into production in 1951.

Jan 1, 1959

By M. P. Youker

USE OF LOW-PRESSURE GAS BURNERS IN OIL- FIELD BOILERS

Feb 1, 1922

By S. C. Schaefer

The Bureau of Mines investigated tIle standard Gibbs energies of formation, 8Gfo, for MllF2 (manganese difluoride) and CoF2 (cobalt difluo-ride). High-temperature galvanic cells employing CaF2 (calcium diflu-oride) as the solid electrolyte were used to measure the open-circuit potentials for the cell reactions ?

Jan 1, 1985

By Welby G. Courtney

The Bureau of Mines conducted a field test program in the Pittsburgh coal seam to investigate the effect of water sprays in the suppression of respirable dust being formed while cutting with a continuous-mining machine. Emphasis was given to the location of spray nozzles on the top and bottom of the cutting boom. Results showed that (1) sumping caused about 60 percent of the dust escaping the face area, and shearing and loading caused the other 40 percent; (2) during sumping, top and bottom sprays were equally effective in dust suppression and reduced dust ~13 percent; (3) during shearing and loading, bottom sprays reduced dust 61 percent and were about 50 percent more effective than top sprays; (4) the combination of top and bottom sprays was slightly more effective than the separate systems, but water consumption increased 60 percent; and (5) inclusion of throat sprays decreased dust reduction by removing some of the water from top and bottom sprays where it was more effective.

Jan 1, 1978

By J. P. Bennett

The Bureau of Mines investigated the dimensional changes of ceramic materials exposed to acid environments to evaluate construction materials for emerging technology in chemical and metallurgical processes. Six commercial ceramic materials (two red shale, two fireclay, one silica, and one silicon carbide (SiC» were exposed to H20, 20 and 30 wt pct HCl, 40 and 60 wt pct HN03, and 10 and 50 wt pct H2S04 at temperatures from 50° to 90° C for 300 days. Linear expansions ranged from a low of -0.02 pct for the silica to a high of 0.45 pct for the red shale. A general ranking of the volume expansion of the materials tested, (from high to low), is as follows: high-porosity red shale A and fireclay B » low-porosity red shale B and fireclay A > silicon carbide and silica. A general ranking (largest to smallest) of the effect of exposure environments is HCl > H2S04, HN03 > H20. An autoclave test method was evaluated. Data obtained from 8-to 24-h exposures were compared with data obtained from the 300-day exposures. The relative expansion trends were similar, indicating that this method could be used as an accelerated test.

Jan 1, 1988

By L. M. Demers, R. E. Edelson, M. P. Rose, D. T. Superdock

The pulmonary alveolar macrophage is a major defensive cell which counteracts the invasive properties of bacteria and particles when these substances invade the pulmonary environment. Pulmonary exposure to coal dust particles is believed to activate these macrophages to release a host of d1emical mediators which can neutralize or contribute to the harmful effects of these dust particles. Our efforts have been concerned with assessing a specific family of mediator substances produced by the alveolar macrophage from arachidonic acid when these cells are in contact with activating substances such as coal dust. Metabolites of arachidonic acid produce a vast array of effects which can impact significantly on pulmonary function both with normal pulmonary events and with pathologic processes of the lung. Our studies demonstrate that isolated alveolar macrophages obtained from rats or guinea pigs cultured in vitro release appreciable amounts of the cyclooxygenase products prostaglandin E2 and thromboxane A2 and release significant amounts of the lipoxygenase products .5-HETE and LTB4. In the presence of l x 104 -1x10·7 g/ml of a coal dust suspension, alveolar macrophages from the rats and guinea pigs alters their pattern of arachidonic acid metabolite release. In the rat, exposure of alveolar macrophages in vitro to the higher concentrations of coal dust causes a significant reduction in PGE2, TXB2 and LTB4 in a 4 hour time course study. In contrast, macrophages from the guinea pig in response to coal dust had little change in TXB2 release, only a slight inhibition in PGE2 production and an initial stimulation in LTB.t release over the 4 hour time course. Cells from guinea pigs released considerably more TXB2 than the rat under these conditions while rat cells formed considerably more LTB4 than guinea pig alveolar macrophages. These findings support the following conclusions.

Mar 1, 1989

By Charles D. Litton

This U.S. Bureau of Mines report describes the results of two large-scale tests conducted to evaluate a prototype nitric oxide (NO)-compensated carbon monoxide (CO) fire sensor, developed by Carnegie Mellon Research Institute (CMRI). In the tests, small coal fires were allowed to develop in the presence of diesel exhaust at relatively low ventilation airflows. These tests compared the response of the CMRI fire sensor with that of other fire sensors, including the Bureau's diesel-discriminating smoke detector. During the tests, CO, NO, and smoke levels were continuously monitored in order to determine the sensor alarm times and gas levels as the fire developed. The data indicated that the NO-compensated CO fire sensor was capable of suppressing the CO produced by a diesel engine and that the sensor responded reliably to the CO produced from the test fires. The tests also showed that the Bureau's diesel-discriminating smoke detector alarmed earlier than the prototype NO-compensated CO fire sensor.

Jan 1, 1993

By John Nagy

Tests were conducted in the Experimental coal mine to study some of the factors that should be considered in fighting mine fires and to obtain data on the effectiveness of different types of extinguishing agents. The investigation was confined to class "A" fires in a zone 20 feet long, involving coal burning on the floor, on the floor and ribs, and on the floor, ribs, and roof of the mine entry. It was determined that the time elapsed between ignition and attack of the fire is very important. A fire in the early stages was found to be controlled more easily and quickly than a similar fire that had burned longer. It was also found that, under suitable conditions, a fire in the floor, ribs, and roof develops very rapidly and consequently might spread over a considerable area if not brought under control quickly. The ventilating current affects fire-controlling operations markedly. Attack in intake or fresh air is highly advantageous, the chief inconvenience being the radiant heat from the fire. Attack in direct return air was impossible for the fires tested in this investigation, because of the high temperature. Universal-type gas masks for noxious gases and smoke offered no protection against the intense heat. Approach to a fire in the return air behind a water-fog curtain is not feasible unless the direction of air flow can be reversed. In one" test fresh air was carried to the fire area with a line brattice. Although the entire controlling operation was in fresh air and masks were not necessary, it was considerably more difficult to control the fire than when a similar fire was attacked in intake air.

Jan 1, 1950

By A. C. Rice

Investigation of a variety of mines to determine efficiency for rare- earth extraction has resulted in a solvent extraction technique wherein Primene 81-R,4 N-benzylheptadeeylamine (BHDA), and Primene JM-T give favorable extraction from sulfate solutions. Extraction from chloride, nitrate, and perchlorate solutions is negligible. Distribution coefficients for 10 rare-earth elements with Primene 81-R establish an extraction sequence beginning with lanthanum and proceeding through lutetium according to atomic number. Yttrium and ytterbium are exceptions in the extract ion sequence.

Jan 1, 1962

By J. W. Paul

[A study of mining methods and underground practices as they influence injury from falls of roof or coal reveals data as to the location in the mine where such injuries occur with the greatest frequency and as to some of the methods and practices which are in use for the prevention of injury. This paper, which presents statistics bearing on the frequency and place of occurrence of accidents and, discusses regulations and practices which have resulted in a low frequency rate from falls of roof and coal in a few representative mines takes its information from mine-accident reports and from the results of studies conducted in a group of 80 mines in the bituminous coal fields of western Pennsylvania, Ohio, and West Virginia. The statistics from this group of mines cover periods of one to four years but average 2 years and 7 months. During this time these mines produced over 110,400,000 tons of coal, equivalent to one-fifth of the annual production of all bituminous mines in the United States. The coal beds of the mines in the group studied are mostly flat, with local pitches of moderate degree. A number of mining plans are in use, each of which follows a general system of multiple entries, cross entries, and rooms. Room and pillar in panels either advancing, retreating, or half advance and half retreat and the block systems are employed. The methods of pillar extraction are by splitting, slabbing, pocket-and-stump, and open end. It is hoped that in presenting some of the details of the methods and practices at particular mines of this group which have commendable records in the prevention of injury some good may accrue to many other bituminous mines which 'nave similar natural conditions.]

Jan 1, 1933

By Debra A. Griffith

The U.S. Bureau of Mines currently is researching the relationship between the level of back strength and the probability of low-back injury. This report is a review of the literature and statistics on over-exertion injuries. Overexertion continues to be a significant source of injury in metal and nonmetal mining, accounting for approximately 24 pct of all injuries yearly. These injuries, particularly to the lower back, can be very expensive in human and monetary terms. An examination of the accident data on overexertion injuries is necessary to provide a background for research into prevention and/or amelioration of those in-juries. The job categories outlined in the Accident Data Analysis data base most affected are "Mechanic/Electrician" and "Mill/Plant Worker." The age group most affected is "30-39" years, and the experience group most affected is "0-.99" years. The most prevalent type of overexertion injury is "Strain/Sprain," and the trunk is the body part most often involved in an overexertion injury.

Jan 1, 1994

By Aldo L. Furno

Sufficient quantities of combustible vapors are released by some sulfurs to produce flammable atmospheres under prolonged storage. Hydrogen sulfide and carbon disulfide appear to be the principal flammable constituents in the vapor space above molten sulfur. If sufficient carbon disulfide is present, ignition of the vapor-air mixtures can occur spontaneously on contact with the heated surfaces found within storage tanks.

Jan 1, 1963

By Fred D. DeVaney

The Mesabi iron district of Minnesota has a potential production of over 50 million tons of iron are annually. The large shipments of ore each year are gradually depleting the reserves, and if the present rate of production is to be maintained there must be a growth in the present available ore supply. Growth is a natural course. The growth of a city may be affected by the addition of city blocks or by the improvement of utilities necessary for its betterment. These may go on in the order named or concurrently. The city-block type of growth of the Mesabi has been tremendous, and the "betterment" type has followed in due course. Probably the former has reached its limit, and if so, more time will be allotted to the latter. It is not the in¬tent of this paper to present either a eulogy of the wonderful mining methods or a history of the milling, but it is pertinent to say that if the lean-ore area continues to produce, the continuance will be more the result of further improvement of milling methods non well under way than of extension of boundaries by the city block plan of growth.

Jan 1, 1932

By H. Kim, R. W. Plummer, T. J. Stobbe, W. G. Jones

"Exposure to airborne dust in coal mines has caused respiratory disease in coal miners. The causal agent in these diseases remains unknown, although the minerals found in and around the coal seam have been implicated. Toxicological studies designed to establish the effect of different mineral combinations and concentrations are lacking because the mineral content of coal mine dust has not been defined. This paper reports the initial results of a study done to characterize the mineral content of the coal mine dust found in a mine in the Upper Freepott seam in Northern West Virginia. Coal mine dust samples were collected using 4- stage cassette impactors at nine locations in the mine. The samples were analyzed by an x-ray microdiffraction film technique supplemented by energy dispersive scanning electron microscopy. Primary size modes of about 17 to 20 micrometers from the samples collected at the haulageway and the returnside of the continuous miner were found. From the returnside of the roof bolter samples, a primary size mode of 12to15 micrometers was measured. The minerals found in high percentages were illite, kaolinite, quartz, and calcite. The distribution of minerals in inter· and intra- location samples showed wide variations. Trends in these variations are presented. Stobbe, T. J.; Plummer, R. W.; Kim, H.; Jones. W.: Characterization of coal mine dust. Appl. Ind. Hyg. 2:95· 100; 1986. IntroductionDisease-associated dusts in coal mine environments continue to afflict miners in today's modern mines. The relationship between exposure to coal mine dust and the development of various respiratory diseases has been well recognized; however, the reasons for variation in occurrence of these diseases among miners in different geographic areas,(1) rank of coal seams,(2-3) and jobs (4) remain uncertain. Several papers have reported on the causal agent in the development of these diseases. Davis (5) found that the percentage of the non-coal minerals present in the lungs of deceased miners increased as the level oi pneumoconiosis became more severe. Reisner (6) reported that cell damage caused by coal mine dust increases with the mineral and quartz content of the dust and with the geo· logical age and rank of the coals. Two studies, investigating the in vitro effects of mineral dusts. reported by Seemayer and Manojlovic (7) also obtained positive correlation between cytotoxicity and the mineral content of coal mine dust. Gormly (8) postulated that destruction of macrophages by certain mineral dusts is the first step in the development of pneumoconiosis. In 1980, Adamis and Timar (9) reported that quartz. sandstone, slate. respirable colliery dust. bentonite, illite, and some kaolins had cytotoxic effects on rat peritoneal macrophages""in vitro."" Walton,(10) however, reported that the presence of high clay, illite, and kaolin mineral exposures reversed the hazards associated with increasing quartz exposures. This finding was supported by Le Bouffant and coworkers.(11) They reported that illite present in coal mine dust strongly inhibited the pathogenic effects of quartz while kaolin had a weaker inhibitory effect."

Mar 1, 1989

By J. A. Eisele

The Bureau of Mines has reviewed the literature related to the recovery of A1203 (alumina) from coal ash. A small amount of unpublished data is also reported. Of the processes studied, the alkaline-sinter process is the most promising from a technical standpoint. However, owing to the high cost of processing coal ash, the dispersed location of powerplants, and the domestic availability of higher grade alternate materials, coal ash does not rank as a primary source material for replacing imported bauxite.

Jan 1, 1979

By L. B. Pankratzt

The heat capacity of dimo1ybdenum carbide (Mo2C) was measured from 51° to 298° K, and the entropy at 298.15° K was evaluated. Heat content measurements above 298.15° It were conducted for dimolybdenum carbide (M0caY) and monotantalum carbide (TaC). The results were combined with known heats of formation and the 298.15° K entropy for TaC to obtain values of the heat and free energy of formation from 298.15° K to 1,400° K for MoaC and from 298.15°K to 1,800° K for TaC.

Jan 1, 1966

By Heinz W. Sternberg

The literature on electrochemical treatment of coal is reviewed, and possible avenues of further research in this field are discussed in this report. Electrolytic reduction of finely distributed coal resulted in the addition of as many as 9 atoms of hydrogen to 100 atoms of carbon. Reduction of coal extracts at controlled potentials indicated the presence of condensed aromatic hydrocarbons and reducible quinones in coal. As much as 65 percent of low-rank coal can be made alkali soluble by electrochemical treatment. Higher rank coals gave smaller yields of alkali-soluble products. However, the nature of this reaction is not clear. The difficulty of reducing coal electrolytically is probably due to the insolubility of coal and not to any structural peculiarity. Reduction of coal by electrolytically generated radical anions appears to be a promising approach for further research.

Jan 1, 1962

By William H. King

The Nevada Massachusetts tungsten deposits (fig. 1) are in the Mill City Mining District in north-central Pershing County, Nev., about 37 miles southwest of Winnemucca. Contact metamorphism of thin limestone beds within a series of metamorphosed sedimentaries formed scheelite-bearing ore bodies. These deposits are distributed over a wide area. A Bureau of Mines development program was started January 11 d was completed on July 25, 1941. This work was centered on the outer and less explored beds in the district and comprised trenching, sampling, and diamond drilling. Exploratory work was done in cooperation with the U.S. Geological Survey. Project work substantially increased the reserve tonnage of marginal ore in three of the areas explored and proved the nonexistence of tungsten in a fourth area. The following pages summarize the history of the district, outline property ownership, and describe physical features and ore deposits. The plan and results of the work performed by the Bureau of Mines are presented along with geologic and topographic maps, assay maps, and diamond drill-hole logs.

Jan 1, 1950

By K. C. Dean

The combination of flotation and chemical processing methods presented in this report of the Bureau of Mines enabled treatment of typical low-grade ferberite ores from the Boulder County, Colo. area, to produce specification-grade synthetic scheelite. The overall recovery from ore to synthetic scheelite was 87 percent, based on a flotation recovery of 93 percent and a similar recovery in chemical processing. Preliminary mineral dressing studies revealed that the physical and mineralogical nature of typical ferberite ores precluded high recovery of tungsten in plus 60-percent-W03-grade products by these methods. Therefore, the flotation research was focused on attaining plus 90-percent recovery in a concentrate containing 10 percent W03. Detailed studies were made (1) to establish optimum grinding conditions for obtaining adequate mineral liberation, (2) to develop collecting and modifying reagent combinations that would enable controllable selective flotation, and (3) to define the influence of different pulp solids, temperature, pH, and time for conditioning and for the rougher and cleaner flotation stages.

Jan 1, 1961