Search Documents

By M. V. HANSEN, Frank PERZ, Edward Thomas, C. H. SEELING

This is the second of a series of information circulars dealing with the control of roof and the prevention of accidents from falls of rock and coal . Their purpose is to focus the attention of the coal-mining industry on the most - common source of fatalities and injuries in mining coal and to disseminate information that may be helpful in combating the roof - fall hazard . Inasmuch as approximately 85 percent of roof - fall accidents occur in the face region , the importance of analyzing the accident - producing aspects of methods of roof support at the face or lack of method overemphasized . - - cannot be This circular is not intended to be an exhaustive treatise on methods of roof support in face regions but rather is a description of several methods of support that appear to offer distinct advantages with respect to safety and efficient operation .

May 1, 1948

By W. T. Reid

A shortage of anthracite for home heating indicates the necessity of using other fuels for this purpose; low-volatile bituminous, or "soft" coal is the most feasible supplementary fuel, either burned alone or when mixed with anthracite. Comparison of Bituminous Coal and Anthracite Whereas anthracite is clean, burns without smoke, and requires little attention, bituminous coal is dusty, tends to burn with a smoky flame, and forms coke in the fire pot that must be broken up to maintain a continuous high output of heat. When properly fired, however, bituminous coal responds more quickly than anthracite to changes in damper settings and consequently can supply more heat in a short time. It is generally less expensive and usually contains less ash than anthracite.

Jan 1, 1943

By George L. Richert

The Minas de Matahambre is situated on the north coast of Cuba, in the Province of Pinar del Rio, approximately 150 miles west of Havana. This nine is the only producer of copper in Cuba, and has been worked for the past 15 years. In 1921 the property was affiliated with The American Metal Co., Ltd., and has been worked by them since that time under the direction of Mr. D. D. Homer, General Manager. Extracts from P. D. Wilson's ?Preliminary report on the geology at Minas de Matahambre? have been freely used in this report.

Jan 1, 1929

By H. F. Yancey

A relatively large proportion of the coal produced in the state or Washington, especially in the coking coal areas is of fine size; hence washing by means of coal-washing tables to reduce the ash content is commonly practiced. For this reason the program of research in coal washing conducted jointly by the U. S. Bureau of mines and the College of Mines, University of Washington, has given special attention to the mechanism of the separation of coal from its impurities as affected by the coal-washing table with the object of

Jan 1, 1931

By Ronald B. Stotelmeyer

This report summarizes studies of 55 Idaho national forest roadless areas completed by the U.S. Bureau of Mines (USBM) in the period 1966-1992. These roadless areas have been recommended for addition to the National Wilderness Preservation System, proposed as special management areas, or otherwise recommended for study by the U.S. Forest Service or the Idaho congressional delegation. The Bureau of Mines' studies indicate which parts of the roadless areas contain mineral resources. They also show where mining and prospecting are likely to occur in the future, where mineral production has occurred in the past, and where abandoned mine workings (possible hazards) would be encountered. The number of mine and prospect workings found are a measure not only of surface disturbance, but of areas not wilderness in character.

Jan 1, 1994

By H. F. Yancey

A relatively large proportion of the coal produced 1n the State of Washington, especially in the coking coal areas is of fine size; hence washing by means or coal-washing tables to reduce the ash content is commonly practiced. For this reason the program of research in coal washing conducted jointly by the U. S. Bureau of Mines and the College of Mines, University of Washington, has given special attention to the mechanism or the separation of coal from its impurities as effected by the coal-washing table with the object of increasing its efficiency. Previous work has evaluated the role of stratification the influence of size, specific gravity and respective shapes of particles in the feed, and the affect of hindered-settling classification of the feed prior to tabling.

Jan 1, 1931

By Thomas C. Denton

ALL of the 45 political divisions of Africa were accessible to non-Communist world industry and commerce throughout 1964, although in some of them revolt and political attitudes presented problems. The position of the continent as a whole for mineral and mineral fuel resources, production, and oversea exports continued to improve. At yearend, significant quantities of a greater number of mineral commodities vital to industry and agriculture were being produced than in any other continent. This statement excludes Communist areas on other continents but might well hold true even if such areas were included. Deriving from its exceptionally diversified production, Africa furnished overseas industrialized countries as a w ole a greater variety of key mineral commodities than any other area. In addition, the value of mineral imports from Africa into the United Kingdom and continental non-Communist Europe probably exceeded the value of such imports from any other area if gold is included and mineral fuels excluded.

Jan 1, 1966

These proceedings consist of papers presented at Bureau of Mines Technology Transfer Seminars in December 1983 for the purpose of disseminating recent advances in mining technology in the area of mine ground control. The Bureau of Mines conducts several of these seminars each year in order to bring the latest results of Bureau research to the attention of the mining industry as quickly as possible.

Jan 1, 1984

By Sidney A. Suhler

A field operable, breadboard model, borehole radar was developed for the detection of hazardous geological anomalies in and above a coal seam in advance of mining. A four-inch diameter downhole probe was fabricated and tested in several environments. The radar transmitter was also employed in a cross-hole or through transmission mode to determine natural geotechnical and man-made conditions between boreholes. Sensitivity to underground conditions in both modes of operation were indicated.

Jan 1, 1978

By H. S. Kalman

A table of factors for rapid, accurate calculation of the volume of pure helium in cylindrical steel containers, at base conditions of 14.7 psia and 70° F, is presented. The table covers a pressure range from 10 to 10,000 psin in 10-psi increments and a temperature range of 0° to 120° F in 2° increments. The volume of helium is calculated from the observed pressure and temperature of the helium, expressed as a factor from the table, and the known internal volume of the container. The calculation requires a single multiplication. A discussion and evaluation of the accuracy obtainable and a derivation of the formula used (which takes into account compressibility of helium, thermal expansion of steel containers, and the stretch of steel due to internal pressure) are presented. An example showing how the table can be used is given also.

Jan 1, 1968

By Deno M. Pappas

The objective of this Bureau of Mines investigation was to identlfy and evaluate alternative binder materials for use in stabilizing and consolidating highly fractured roof along longwall faces and gate roads. The desirable characteristics of a stabilization material were defined, and an extensive search was conducted to find materials satisfying these characteristics. Of 20 materials originally scrutinized, 9 were chosen for laboratory analyses. The laboratory tests evaluated bond strength and tensile strength under both dry and wet conditions. An optimum material was not found. The laboratory analyses indicated two possible candidate materials for longwall stabilization: high-aluminous cement and two-component epoxy; however, the tensile strength of the high-aluminous cement was mediocre, and the epoxy cement is toxic, flammable, and fairly expensive. The potential market demand for an effective and economical stabilization macerial is discussed in the appendix.

Jan 1, 1988

By Nunna Malakondaiah

Plant samples collected from the mined sites of Beulah, Center and Zap and the test sites of North Beulah 1, North Beulah If, South Beulahh and Center were analyzed for their nutrient concentrations. The vegetation from the mined areas generally showed lower concentrations of Na, P and Cu and failed to meet the nutritional requirements for beef cattle as defined by National Research Council (minimum requirements are: Na, 600; Cu, 4; P, 1800 µg/g dry weight). Plants from Beulah showed generally higher concentrations than from Center or Tap. Tissue concentrations of K varied significantly between sites for 5 species due to the low tissue concentrations at Center. Deficiencies are difficult to isolate as the sampling was done in mid-summer and generally during that season the tissue concentrations tend to decrease in several species. All of the plant species at the unmined sites, with the exception of western wheatgrass at Zap, had lower concentrations of P than the minimum nutritional requirements for beef cattle. Sodium concentration was low but Cu was marginal to adequate in plant species at the unmined sites. Concentrations of K, Mn and Cu in western wheatgrass were greater at Center than at Zap while the opposite was true of the concentrations of Zn, Cu and P in blue grama and Cu in green needlegrass. Amending the spoil with slack at North Beulah I decreased the concentrations of Zn, Cu and P in wheatgrasses grown on spoil from 0-2, 5-10, and 20-25 foot depths, respectively. In general, the mean tissue K+/Na+ ratios were greater in plants on slack amended spoils, primarily due to the reduced Na concentrations in the tissue. At North Beulah II test site, only wheatgrasses grown on spoil amended with slack showed significant increase in K and decrease in Na and Mn concentrations. At South Beulah test site which received 12" topsoil over graded spoil, leonardite amendment decreased P concentrations in all of the grasses as compared to control, whereas fertilizer treatment increased the same. Nutrient concentrations were lower in both fescue and needlegrass with leonardite treatment and higher with fertilizer treatment although not significantly different from control. The concentrations of Ca, Mg, Na, Fe, Cu and N in grasses grown on topsoil at Center test site were significantly higher than on slack amended spoil. Legumes grown on topsoil at Center site contained higher concentrations of P than those grown on spoil; there were no significant effects due to slack on spoil or topsoil. The data presented in this report act only as an indication of between-treatment and between-species differences in tissue composition of plants harvested in mid-summer season. With respect to the nutrients analyzed, since none were found to be toxic, the cattle can safely feed on the vegetation of these mined areas.

Jan 1, 1982

By R. V. Ramani

In this the available information friction factors and leakage report, on characteristics are reviewed and summarized. The use of Penn State Mine Ventilation Simulator (Volumes II and III of the Final Report) to analyze the sensitivity of the ventilation system to the changes in leakage and friction factors is discussed with examples. In simple ventilation systems, the results of changes in leakage and friction factors can be easily solved and explained by the laws of air-flow. In complex systems, with fixed quantity branches and multiple sections, the effect of changes in leakage and friction factors cannot be generalized. This study points out the importance of good input data for obtaining reliable information from computer analyses and demonstrates the application of simulators to analyze the effectiveness of ventilation systems. An extensive bibliography on friction factors, leakage characteristics and ventilation economics is included.

Jan 1, 1977

By David A. Benjamin

From 1986 to 1989, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied the 59,600-acre Mexican Mountain Wilderness Study Area (UT-060-054) in order to evaluate its identified mineral resources. The study area is located in Emery County, UT, about 24 miles east of Castle Dale, UT. A review of the geologic and mining literature, and a field examination identified two uranium prospects in the Wilderness Study Area, and three copper prospects nearby. One-hundred ninety-five rock samples were taken.

Jan 1, 1989

By Gary A. Kingston

Chromium resources in the United States are estimated at 1.8 million tons of recoverable chromium contained in 22.5 million tons of chromite-bearing material. Additional resource is presumed existent in large, but as yet undetermined, quantities of material containing less than 10 percent Cr203. No domestic resources are being mined presently (1969). Excluding transportation charges to domestic consuming areas, the total 1.8 million tons of chromim is estimated to be available, in ore or concentrate, at costs up to $0.64 per pound; 63 percent of the total is available under $0.11 per pound; and 38 percent under $0.08 per pound. It is judged that transportation from the resource areas to the existing market centers would add nearly $0.05 to the cost of a pound of chromium contained in ore or concentrate. Technically effective beneficiation methods have been developed for much of the known domestic resource, and further development might reduce costs of processing these materials. However, at present, domestic chromium resources are noncompetitive with foreign sources.

Jan 1, 1970

By B. M. Stewart

Researchers at the U.S. Bureau of Mines conducted a long-term groundwater monitoring and site characterization program at an abandoned 10-ha, acid-producing, copper-gold tailings impoundment in north-central Washington State. The purpose was to investigate contaminant release and transport, and attenuation mechanisms in the tailings, sediments below the tailings, and gravels downgradient of the impoundment. This report summarizes the monitoring results and physical properties of the tailings, the sediments below the tailings, and the groundwater system associated with the tailings. Water samples from the vadose and saturated zones of the impoundment were analyzed for 15 constituents. Concentrations of the same constituents were determined in water samples up to 3 m beneath the impoundment and in the shallow colluvium and deep bedrock at 76, 335, and 550 m downgradient and 168 m upgradient. Constituent concentrations within the tailings are quite variable and are influenced by pH, depth of oxidation, grain-size differential (surface area), hydraulic gradient, groundwater mixing, and the presence of hardpan layers, carbonaceous material, and organic matter. Most of the metal constituents decreased to background or near-background concentrations in the farthest downgradient well.

Jan 1, 2010

By Arel B. McMahan

The U.S. Bureau of Mines investigated mines, prospects, and mineralized areas in the Owlshead Mountains Wilderness Study Area (WSA) in 1982. Within the WSA, subeconomic manganese, iron, zinc, and lead resources were identified at two mines; sample analyses indicate five other mines and prospects may have gold, silver, iron, manganese, and copper resources. Three mines examined adjacent to the WSA have identified manganese and iron resources; and sample analyses indicate manganese, iron, and gypsum resources may exist at two prospects. Greatest likelihood for future identification of mineral reserves is for manganese at the Black Magic Mine in the southeast part of the WSA. The southern half of the WSA contains nearly all identified mineral resources, and properties at which sample analyses indicate additional resources. The most significant are manganese and iron resources at the Black Magic Mine in the southeastern part of the WSA; and the Ellie, New Deal, and Owl Hole Mines adjacent to that part of the area. Manganese and iron minerals filled fractures and replaced limestone in brecciated and faulted contacts with intrusive granitic rocks. In the southwest corner of the WSA, sample analyses indicate four prospects may have gold and silver resources. These precious metals are in gouge zones along contacts where diorite has intruded volcanic rocks. A small identified resource at the Kennedy Boys Lead Mine in the western part of the WSA consists of quartz veins with zinc and lead minerals along a brecciated contact between granite and limestone roof pendants.

Jan 1, 1985

By James A. Whelan

The Bureau of Mines sponsored research studies of variables in rotary drilling, done in the Department of Mineral Engineering, University of Minnesota. By studying carefully controlled drilling with good instrumentation, it was hoped to obtain a better understanding of rock failure during drilling and of the stresses in drill bits during drilling. Experimental procedures and equipment are described. From these studies it was concluded that 1. Thrust requirements, other things being equal, are proportional to the total length of cutting edge in the bit. 2. Data from penetrating a wedge into rock under thrust only are not directly applicable to rotary drilling. 3, In rotary drilling the initial wear on a bit greatly decreases penetration rate under any given set of conditions; however, after initial wear the effect of wear on penetration rate is reduced. 4. An increase in rotary speed increases the overall penetration rate but decreases the penetration per revolution. 5. An increase in thrust increases the overall penetration rate and the penetration per revolution. 6, Torque on a drill bit is proportional to both penetration rate and bit diameter. 7. For small-diameter holes full-hole drilling will save both drilling time and energy compared with pilot drilling followed by reaming; for large-diameter holes pilot drilling-reaming is advantageous in both respects,

Jan 1, 1962

By Joseph Cervik

This Bureau of Mines report deals with water infusion of coalbeds, which can control methane emission at face areas during developmental mining and which may sometimes suppress dust. Studies show that water infused into the coalbed flows through the fracture system and displaces the methane in the fractures and prevents migration from the solid coal. Displaced gas migrates away from the face area that has been water infused and enters the return ventilation airways. A gradual decrease in methane emission is observed from the start of infusion until the infused zone is mined through. Depending on the permeability of the coalbed, infusion pressures ranged from 300 to 2,200 lb/in2. Face emissions in the Upper Kittanning coalbed were reduced by 89 pet; reductions of 38 to 79 pet were measured in the Pittsburgh coalbed depending on the relationship between the face cleat direction and mining direction. Respirable dust levels were reduced by about 75 pct on a longwall section in the Pocahontas No.3 coalbed and by about 50 pct on a development section in the Upper Kittanning coalbed, but no statistically reliable reduction was found in the respirable dust levels in the Pittsburgh coalbed.

Jan 1, 1977

By Arno C. Fieldner, J. W. Paul, WALTER A. SELVIG

Many mine samples of coal are analyzed each year in the laboratories of the Bureau of Mines. The analyses are made in connection with investigations relating to fuels belonging to or for the use of the United States Government, the causes of accidents in coal mines, the geologic relations of coal beds, and the quality and the value of the coal and lignite in the public lands. The systematic collection and analysis of such samples in connection with fuel investigations was begun in 1904 at the Government fuel-testing plant at the Louisiana Purchase Exposition. and was under the direction of the United States Geological Survey for six years. Descriptions of the coal samples collected between the beginning of this work, July 1, 1904, and the transfer of the fuel-testing and mine-accident investigations to the Bureau of Mines,July 1, 1910, were compiled and published in Bureau of Mines Bulletin 22.' Descriptions and analyses of samples collected during the fiscal years 1911 to 1913 were published in Bureau of Mines Bulletin 85.2 Descriptions and analyses of samples collected during the fiscal years 1913 to 1916 were published in Bureau of Mines Bulletin 123.3 The present bulletin presents analyses and descriptions of samples collected during the fiscal years 1916 to 1919. In order that the material in this bulletin may be used to supplement that presented in Bulletins 22, 85, and ,123, the same plan of geographical classi- fication has been followed, the analyses and descriptions of the samples being grouped in alphabetical order according to the State, county, and town near which the mines or prospects sampled are situated.

Jan 1, 1922