Search Documents

By X. -G. Chen, E. M. Elgallad

Direct chill (DC) cast ingot plates of 2xxx alloys have been increasingly used for large mold applications in the plastics and automotive industries. A novel heat treatment practice for Al-3%Cu-1%Mg DC cast ingot plates has been developed, involving solution treatment, furnace cooling to the desired aging temperature and holding for appropriate time at the aging temperature. The mechanical properties of the plates were studied for different combinations of aging temperature and time, using hardness measurements and tensile testing. The evolution of the strengthening precipitates was investigated under different cooling rates corresponding to cold water quenching, still-air cooling and furnace cooling, using electrical conductivity measurements. The results showed that by applying the novel heat treatment, the cast ingot plates could provide a wide range of combinations of strength and ductility satisfying the design specifications of large molds. This, in turn, offers a practical solution for the fabrication of extremely large DC cast plates combining between good mechanical properties and low levels of residual stress using the shortest possible heat treating cycle.

Jan 1, 2015

By K. E. Waters, N. Brodusch, R. Gauvin, A. Jordens, Teng. C., H. Demers

Rare earth elements (REEs) become increasingly significant for renewable energy devices and high-technology electronic products because of their large-scale popularity and applications. In this project, a field-emission scanning electron microscope was used to characterize the composition and distribution of REEs-bearing minerals. X-ray elemental maps were acquired with a large area x-ray detector (60 and 80 mm2 collecting area) and annular detector (60 mm2 collecting area), which allow fast x-ray acquisition at high count rate. These elemental maps were transformed into phase maps, which are used to identify the composition of the mineral phases and the REEs distribution over a large area. The phase maps are an easy way to distinguish the phases with and without REEs and compare the efficiency of different REEs extraction processes. Different methods (manual and automatic) for producing phase map were studied by comparing the distribution of REEs obtained from the same area.

Jan 1, 2015

By Eduardo R. Rodrigues, Ankur Narang, Roberto Federico Ausas, U. T. Mello, Jose Maria Segura Serra, M. R. Lakshmikantha, Ignacio Carol, Kamal C. Das

"Modeling of big faults or weak planes of strong and weak discontinuities is of major importance to assess the Geomechanical behaviour of mining/civil tunnel, reservoirs etc. For modelling fractures in Geomechanics, prior art has been limited to Interface Elements which suffer from numerical instability and where faults are required to be aligned with element edges. In this paper, we consider comparative study on finite elements for capturing strong discontinuities by means of elemental (EFEM) and nodal enrichments (XFEM) for Geomechanical applications. For general fracture scenarios, Oliver et al. (2008) have demonstrated advantages of EFEM over XFEM for including: (a) ease of modeling in any standard finite element code due to the possibility of static condensation, (b) higher accuracy in some cases for coarse meshes, and, (c) a reduced computational cost. However, there has been no work that considers cohesive fractures in Geomechanics. We present a numerical analysis based on a linear constitutive model and linear triangular elements for the bulk and a linear constitutive behaviour for the fault for a representative set of fault planes in a circular tunnel made in rock mass. In the numerical examples we consider both well-traced and bad-traced meshes. We focus on traction profile analysis for both EFEM and XFEM, since that is crucial to understand the cohesive fracture behaviour specially rock joint. Therefore in each case, shear, normal and stress ratio are compared across the two methods along the fault plane. This is the first such work that compares XFEM and EFEM behaviour for Geomechanics problems.For the considered class of problems and the sharp penalization approach without regularizations adopted, it can be observed that accuracy and robustness of EFEM may strongly depend on the fault orientation with respect to the element edges, while, XFEM is independent of fault alignment with element edges. It has been also observed that, with mesh refinement model, stress oscillation completely removed with XFEM however EFEM fails to provide oscillation free results with finer mesh in case bad-traced model. We also performed error analysis and found that in case of bad-traced mesh the average error in the XFEM is 84% smaller than of EFEM and for XFEM the error goes to zero with increasing mesh resolution, while for EFEM the error increases with mesh resolution. Thus, we experimentally demonstrate that, XFEM performs better than EFEM in terms of accuracy and rate of convergence with marginal increase in computational cost. This work hence provides novel insights on the application of XFEM and EFEM in Geomechanics."

Jan 1, 2015

By J. Zachwieja

As part of a general review on study of surfactant blinding agents to improve gold recovery during cyanide leaching of carbonaceous gold ores, processes of CIL and RIL leaching using surfactants were investigated. When refractory ores were treated by surfactants, CIL and RIL leaching processes yielded significant improvement on gold recovery. This paper will discuss and compare the laboratory results from two different leaching processes on preg-robbing ores, as well as, illustrate the difference of potential fouling of the blinding agents on activated carbon and resins.

Jan 1, 2015

By Farzad Khodabakhshi, Adrian P. Gerlich

"In this article, cold spraying process was utilized to coat the surface of AZ31 magnesium alloy with a layer of AA7075 aluminum alloy. Thereafter, friction-stir processing (FSP) was employed to enhance the microstructure and consolidate the deposited layer. The grain structure and phase morphology were studied along with indentation hardness before and after cold spraying and friction stir processing. The magnesium substrate had an initial hardness of 74 HV which increased to 102 HV after FSP due to refinement of grains to <2 µm. The aluminum coating layer, provided improved surface hardness up to 160 HV, which further increased to 173 HV after FSP was applied.INTRODUCTION Cold spray is a material deposition process which can be used for surface modification, since it deposits material on a metallic substrate with little heating by way of high velocity ballistic impacts. Using cold spray technology, it is possible to deposit a wide range of coatings with various thicknesses by controlling the characteristics of the feeding powder and metal substrate, gas temperature, gas pressure, powder feeding rate, nozzle geometry, and gun traverse velocity. This process has been recently employed for surface modification in various aircraft and automobile structural applications. This has led to a broad range of research using this process for production and modification of different metallic and non-metallic systems. In the present study, cold spray process was used to deposit a uniform layer of aluminum-zinc alloy (AA7075) on the surface of AZ31 magnesium alloy. This coating was subsequently treated by way of friction-stir processing (FSP) as a new post-spraying modification technique to enhance the structural homogeneity and densification of the coated aluminum layer. This method utilizes a non-consumable rotating tool with a specially designed shoulder and pin that is plunged into the surface of metal to be modified and then moved along the direction of interest. The localized frictional heating between the rotating tool and workpiece leads to softening of the materials around the pin, and material extrusion through a complex flow of material from the advancing toward the retreating side the tool. To the author’s best knowledge, only a few reports discuss the modification of a cold sprayed deposit by FSP process. The microstructure and mechanical properties of the cold sprayed layer and substrate before and after FSP modification were examined using optical observations (OM) and indentation hardness testing. Furthermore, the AZ31 alloy substrate alone was treated with FSP as well, for the aim of comparison to the processed coating."

Jan 1, 2017

By Zihe Ren, Edouard Asselin, Marcus Tomlinson, Tianbi Zhang, Jing Liu

"Raman spectroscopy is used to quantify the extent of disorder in the carbonaceous matter associated with preg-robbing ores. Previous studies of Goldstrike ores showed that the height and width of the peaks for the “D” (disordered) and “G” (graphite) bands, the so-called “Raman ratio” had a strong correlation to the preg-robbing value (PRV) measured for various ore samples. A brief literature review on Raman spectroscopy as it applies to preg-robbing ores is presented. Further, recent studies, presented here, have shown no correlation between the Raman ratio and the PRV for a wide variety of ores. This suggests that the extent of organic carbon crystal disorder is not the main factor in determining preg-robbing characteristics.INTRODUCTION Preg-robbing may arise from natural carbonaceous materials in the ore. Several mechanisms have been proposed in the past decades including a physical sorption process by the carbonaceous matter, or via the reduction of aurocyanide at the mineral surface (Abotsi & Osseoasare, 1986; Afenya, Osseoasare, & Abotsi, 1983; Tan, Feng, Lukey, & Van Deventer, 2005). Nevertheless, the mechanisms of preg-robbing remain poorly understood. Understanding the nature of the preg-robber is of practical importance for the selection of a suitable treatment process. Fine carbon particles in the ore have been recognized as preg-robbers due to their similarity to the activated carbon used in the carbon in leach (CIL) or carbon in pulp (CIP) processes. Previous research has illustrated that the activated carbon (also referred to as amorphous carbon in some literature) has a much higher absorption ability than pure graphite with high crystallinity (Adams & Burger, 1998). Adams et al (Adams, Swaney, Friedl & Wagner 1996) concluded that carbonaceous matter is largely responsible for the overall preg-robbing capacity of a given ore. However, the mechanism of carbon preg-robbing was still not clear mostly due to the complexity of amorphous carbon and its behavior in different solution matrices, and at different pH and temperature (Adams, 1990, 1993)."

Jan 1, 2017

By Pura Alfonso, Teresa Escobet, Hernan Anticoi, Eduard Guasch, Josep Oliva, Sarbast A. Hamid

"The liberation modelling of mineral particles using mineral liberation analysis have been used in the past to model comminution and concentration processes. In this work this concept has been taken a little further, using comminution and concentration for applying the mineralogical characteristics of particles. This approach is shown using the image analysis, mineral liberation analysis and the distribution density functions for liberation modelling. The work focused on the effect of comminution on mineral liberation for liberation modelling. To model this, effect the mineral liberation of the particles using distribution density and the cumulative distribution was linked to the image analysis of the ore particles. These properties have been estimated by statistical measures such as the distribution density and liberation grade, which were extracted from MLA data and images analysis, using proper image analysis and techniques based on MATLAB software. A comparison of different tungsten ores of liberated particles, has been introduced and evaluated by estimated results and image analysis.INTRODUCTION The chief economic minerals of tungsten are wolframite [(Fe,Mn) WO4] and scheelite(CaWO4), and approximately two-thirds of the world tungsten reserves consist of scheelite deposits (Lassner and Schubert, 1999). Tungsten has unique properties and is widely used in various industrial high strength and high temperature applications. It occurs coarsely aggregated in low grade ores. Most of tungsten ores, particularly scheelite, wolframite and ferberite, occur in deposits with very low content of WO3 (0.1–2.5%) that is not economically viable to apply directly metallurgical methods to extract tungsten (Martins, 2014). Tungsten is considered as a critical metal by the European Union by the economic importance and also the high supply risk (European Commission, 2014; Chakhmouradian et al., 2015).Currently, scheelite is playing an increasingly important role in tungsten industry because the mineral reserve of wolframite is getting depleted after gradual exploitation and utilization (Min et al., 2016). In mineral processing, the liberation of valuable mineral from the gangue determines the efficiency of subsequent separation processes. The liberation characteristics of an ore are primarily dependent on its texture, the association of mineral in the host matrix of gangue minerals, and to some extent on the grinding process (Zhang and Subasinghe; 2013)."

Jan 1, 2017

By M. A. Halim, V. I. Lakshmanan, Z. Jankovic

An innovative mixed-chloride process for the separation of iron from lateritic ore is described. The separation of Fe(III) from leach liquor is an important process step for the recovery of nickel and cobalt. The patented process of Process Research ORTECH Inc. uses a lixiviant containing hydrochloric acid (HCl) and magnesium chloride (MgCl2) for the leaching of lateritic ores/concentrates followed by the selective solvent extraction step of Fe(III) over other value metals such as Ni and Co. The use of MgCl2 increases the activity of the hydrogen ion in the lixiviant, which reduces the consumption of HCl in the leaching stage and enhances the formation of HFeCl4-, thereby increasing the solvent extraction efficiency of Fe(III) with ketone. The process produces high purity iron oxide (Fe2O3) and regenerates HCl by the pyrohydrolysis of the FeCl3 rich pregnant strip solution. The developed process flowsheet is in closed loop, economically attractive and environmentally friendly.

Jan 1, 2015

By Yihan Liu, Jintao Zhang, Chen Xiao, Xiaomeng Zhao, Guanglei Song

To estimate the performance of the inert anode materials based on NiFe2O4 spinel ceramic during it used for aluminum electrolysis, we investigated the wetting process of cryolite molten salt which is in composition of industrial aluminum electrolysis with carbon anode and NiFe2O4 based cermet materials, by means of determination the interface wetting angle between the molten cryolite electrolyte and the solid anodes interface. The results show that the wetting angle between the electrolyte and carbon anode is larger than 90 angulation, this means that they basically can not wetting; however the nickel ferrate spinel ceramics behaves much better. In regard to the NiFe2O4 matrix materials, their initial wetting angles is 76.9. The initial wetting angles for 1.0wt%MnO2, 2.5wt%TiO2 and 0.5wt%V2O5-doped samples are respectively 56.86°, 52.98° and 51.93°. However, after 50s later, all the wetting angles came down below 15°.

Jan 1, 2015

By D. N. Madge

The use and development of industrial process control computers in the mineral industry during the 1970&apos;s has been sluggish. This cautious approach is due to lack of commitment by senior management. The lack of commitment is due to several reasons: variable mineral processes and technologies, market fluctuations, and excessive costs and inadequacies of applicable products supplied by computer vendors.

Jan 1, 1979

By C. Schmidt, M. Kohnk, C. Siemers, J. Kiese

The application of conventional titanium alloys is limited to 550°C due to their poor oxidation resistance. In addition, severe grain growth is observed in single-phase titanium alloys in long-term runs at elevated temperature leading to a degradation of their mechanical properties. In exhaust applications in automotive or aerospace engineering, products are often manufactured by cold-deformation like deep-drawing or rolling which is normally difficult in oxidation-resistant titanium alloys due to the presence of titanium-silicides. Therefore, in the current study, titanium alloys based on CP Titanium Grade 1S (soft grade) were developed showing (1) improved oxidation resistance due to a concerted addition of silicon, iron and niobium, (2) microstructure stability by the precipitation of hafnium-silicides mainly on the grain boundaries and (3) good cold-deformation properties. The industrial production route was developed so that the new class of Ti-Si-Fe-Nb-Hf-alloys is now ready for application in exhaust systems of planes or cars at minimum 800°C.

Jan 1, 2015

By A. Scheltema Beduin, H. Oterdoom, A. Haaks, C. Kempe, A. Liedtke

"For the Kazchrome DC Ferrochrome plant, SMS-group specifically designed an electrode column that would minimize downtime. Special features include the possibility for on load electrode jointing, on load slipping, and back-slipping. Electrode consumption is strongly related to furnace load and impedance, and is very low at high loads, which makes the graphite electrode an alternative to consider even in AC applications. The electrode could also be applied in other DC applications, as for example TiO2 slag, the novel Conroast process, or (twin) DC FeNi furnaces, and could possibly be installed during bigger shut downs. This paper will describe some of the design considerations and operational performance data on this novel column in the FeCr industry that could also be of interest for the FeNi or PGM industry if these would continue to develop towards DC technology.INTRODUCTION Every DC furnace has a cathode and an anode. The anode applied is commonly known as the Concast design, though the original design was by ABB who handed it over to Concast, subsidiary of the SMS-group. Some well-known DC furnaces outside the steel industry where the Concast bottom has been installed are listed in Table 1 as well as a few other key design features.Sidewall cooling and some other data have been left out for reasons of space, and being a lesser relevant design feature to this paper. HES stands for Hollow Electrode System, in which feed is charged through an electrode. Table 1 is built up chronologically according to first start-up date. Below comments are given to briefly explain some of the columns in Table 1: •,“Arm” in the “Cathode” column means that the design of the cathode holding and regulating mechanism consists of an electrode arm as depicted in Figure 1. •,Charging is relevant as some operations started with HES charging, whereas recently most new operations have started without HES but only charging chutes, of which at least some are close to the electrode and possibly others installed closer to the sidewall. •,“Dome” in the “Roof” column means that the design of the roof involves a center piece that can be exchanged if worn. •,The optimal roof design still seems to be a topic of debate, where no design is without problems."

Jan 1, 2017

By ByongPil Lee, Changkyu Lee, Jin Gyun Park, Hyung Sub Eom, Sung-Koo Jo, Jae-Young Lee, Gilsoo Han

"A new hydrometallurgical process for nickel extraction from a low grade laterite ore such as limonite has been developed by RIST and POSCO. This POSCO Nickel Extraction Process (PosNEP) consists of five main processes: ore reduction using hydrogen as a reductant; acid leaching at atmospheric pressure and temperature; cementation by the use of reduced-ore seed; production of the main product such as ferronickel or a high purity nickel compound; and production of by-products such as cobalt and iron in the forms of cobalt sulfate and iron oxide. In addition, hydrogen produced in acid leaching and hydrochloric acid regenerated in pyrohydrolysis for iron oxide production can be reused in the process, which makes PosNEP more cost-effective. The performance of PosNEP has been proven through pilot tests, showing that this process is economically and technically viable. In this paper, basic concepts and detailed test results of PosNEP are shown.INTRODUCTIONNickel has been extracted from two types of ore, sulfide and oxide ore. Nickel and cobalt usually occur together in the ores. The principal ore mineral of the sulfide is pentlandite, (Ni,Fe)9S8, which is easily beneficiated to produce sulfide concentrates(Moats & Davenport, 2014). These concentrates are usually treated by smelting and converting to make a matte. The produced matte is then purified through either hydrometallurgical or pyrometallurgical processes to produce high-purity nickel. In general, this process for sulfide ore has been known as a more cost-effective process than that for oxide ore.The oxide ore is laterite comprised of two different ore types, saprolite and limonite. The main nickel-bearing mineral of saprolite is nickeliferrous garnierite,(Mg,Ni)6Si4O10(OH)8, and that of limonite is nickeliferrous goethite (Fe,Ni)O·OH ore (Moats & Davenport, 2014). Since the saprolite has high contents of nickel and slag formers (MgO and SiO2) and a low content of iron, it tends to be treated by a pyrometallurgical smelting process such as calcination and electric furnace techniques to produce ferronickel for use in stainless steel. In this process, the cobalt in the ferronickel does not have any economic value."

Jan 1, 2017

By P. Chu, J. A. Finch

The formation of small bubbles in flotation is usually accomplished by the use of frothers, or sometimes is due to the presence of inorganic salts in the process water. The effective mechanism associated with the presence of these solutes is generally considered to be coalescence inhibition. However, recent work has demonstrated that the presence of frothers and salts also reduces the size of bubble at the initial formation stage. In this paper we adapt the same experimental setup to investigate the time that it takes for a bubble to form; for a known system power input, the energy to form a bubble can then be estimated from the time. The hypothesis is that the presence of frother and salt will reduce the time for a bubble to form, which can be interpreted as an added energy component being derived from the solute. Testing different types and concentrations of frothers and salts, the hypothesis is supported: the mechanical energy required to form a bubble decreases by about 10% in the presence of these solutes.

Jan 1, 2015

By Ahmad Ghahreman, Lin Li

"In this study, the Fe(II)/Fe(III) redox reaction kinetics on the surface of pyrite, have been investigated in a 0.5 mol L-1 sulfuric acid solution for a temperature range of 22 to 65°C. Based on mixed potential theory, chronoamperometry is introduced to study the Fe(II)/Fe(III) kinetics by subtracting the current density of pyrite oxidation in an iron-free acidic solution from that in an iron-containing solution at the same applied polarized potential. Tafel behavior was established by this method to analyze the kinetics of the Fe(II)/Fe(III) redox reactions. The results showed that exchange current densities increased slightly with temperature, however remained on the order of 10-5 A cm-2. The activation energy for Fe(II) oxidation and Fe(III) reduction on the pyrite surfaces was calculated to be 102.0 and 32.7 kJ mol-1, respectively. Anodic transfer coefficients also increased, from 0.24 to 0.39, with increasing temperature, which indicates a weakened n-type semiconductor property at higher temperatures. Electrochemical impedance spectroscopy measurements have indicated that at lower anodic over potentials the charge transfer is the rate determining step of pyrite oxidative dissolution in sulfuric acid solution. In the presence of Fe ions, the major contribution of the total current density comes from the Fe(II)/Fe(III) redox reaction. INTRODUCTION Pyrite, an abundant sulfides mineral in the nature, is commonly considered a valueless gangue mineral frequently associated with other valuable sulfide minerals such as chalcopyrite, or metals such as gold, or coal (Lin & Say, 1999). Pyrite oxidation has been the subject of extensive research in view of gold metallurgy, as oxidation of pyrite is the initial step to break down the pyrite lattice and expose the encapsulated fine gold particles (Gasparrini, 1983). Fe(III) ion and dissolved oxygen (DO) have generally been considered as the two most important oxidants with respect to pyrite oxidation, having been studied extensively in previous research (Zheng, Allen, & Bautista, 1986; King Jr & Lewis, 1980). The process of pyrite oxidation can be viewed as a series of reactions amongst pyrite, ferrous, ferric and oxygen in which pyrite is initially oxidized by the dissolved oxygen in water forming ferrous (Eq. 1), and then the ferrous also is oxidized by he dissolved oxygen to form ferric (Eq. 2). The ferric, produced by reaction 2, then could potentially oxidize pyrite (Eq. 3) and convert to ferrous."

Jan 1, 2017

By W. D. Freeborn

Slim-hole drilling and completion techniques were first used in the Cynthia area of the Pembina field, Alberta, by the Texaco Exploration Company in the summer of 1957. Prior to that time, eighty-eight wells had been drilled and completed in this area in a conventional manner. Subsequent to the initial four-well evaluation programme, twenty-one additional wells have been drilled using slim-hole techniques. No difficulty was encountered in the drilling and completion of slim-hole wells, or in obtaining production from them. A comparison of drilling and completion economics and practices has been made for slim-hole and conventionally completed wells. Penetration rates for both bit sizes (614 in. and 9 in.) were relatively equal. The shorter life of the smaller bits required the use of 15 per cent more bits per well, but the total trip time to change bits was similar for both hole sizes because of the higher hoisting speeds possible with the lighter drilling strings used in the slim holes and better hole conditions. Completion costs of the slim holes were reduced by 37 per cent as compared to the costs of conventional-type completions. This was made possible through the use of smaller well equipment, the elimination of tubing, and a reduction in rig time for completion operations.

Jan 1, 1958

By David Ulrich Furrer

Materials and manufacturing processing technologies have played an important role in the development and capabilities of nearly all manmade products. Market drivers for fuel efficient, low cost, environmentally friendly, more capable transportation has given rise to significant materials challenges and subsequent developments. The rate of improvement and implementation of new commercial products can be limited by the rate of new materials and process technology development and qualification. As many materials are being designed for unique requirements and even location-specific unique properties, the implementation of tools and methods to enable rapid characterization and validation of material definitions and design systems must also be accelerated. A review of new integrated material, manufacturing process and component designs, engineering processes and emerging tools and methods will be discussed. The linkage of computational materials science and engineering into component design will also be discussed along with the challenges and opportunities for further growth and application of integrated computational materials engineering (ICME).

Jan 1, 2015

By N Berkowitz

Slurry pipelining, as now under-stood and practised, can only command marginal interest in Canada, as long-distance railway freight charges in this country are generally lower than slurry pipeline tariffs. Several alternatives to conventional slurry transmission are, however, now emerging, and two such alternatives are briefly discussed with reference to coal pipelining. In one, coal is transported as a suspension in oil; the other contemplates the movement of paste "slugs." Preliminary economic estimates indicate that the resulant process simplification and adoption of common carrier principles could lead to cost reductions that might make Western coal competitive with imported fuel in the power generating stations of eastern Canada. R ECENT appraisals of slurry pipelining techniques, some-what incongruously &apos;based upon the performance of successful installations (1,2), are making it increasingly apparent that current solids pipelining methods can only command marginal interest as methods of bulk commodity transportation (3). Although some uncertainties remain in matters of detail, it is now generally conceded that long-distance slurry pipelining cannot compete against rationalized railway transportation unless movement of

Jan 1, 1963

By T. Johnson, K. Lambrych, D. Kelley

Materials for construction of equipment used in hydrometallurgical plants are selected based on a combination of their ability to perform as required in aggressive process environments as well as their cost. As a material of construction, fiber reinforced plastic (FRP) has been shown to provide equal if not improved durability relative to alternative materials such as corrosion resistant alloys at a considerably lower cost. This is particularly true in the case of equipment used in acid leaching processes for copper, cobalt, nickel and rare earth elements. The selection and extensive use of FRP over alloys in new hydromet plant construction in North and South America illustrates this advantage of FRP effectively. This paper will compare corrosion performance and cost of plant equipment fabricated with stainless steel alloys and FRP made with Epoxy Vinyl Ester thermoset resins. Real world case histories for FRP piping, storage tanks, extraction vessels, and electrowinning cells combined with laboratory based corrosion studies will be reviewed to demonstrate how FRP materials are selected for hydrometallurgical equipment.

Jan 1, 2015

By L. Gonzalez-Sardi, W. McCombe, M. Pearson

Pressure oxidation is increasingly being used for processing refractory sulphide ores and concentrates because it offers highly effective base metal and precious metal extraction while minimizing elemental sulphur, arsenic & mercury emissions. Yet pressure oxidation processes introduce new safety concerns and process risks as demonstrated by a number of safety incidents over the last 20 years, including overfilling, oxygen-metal fires, nozzle/sparger failures, and uncontrolled pressure relief events. Chemical Process Safety regulations in the United States and Canada mandate that companies constructing or operating chemical process facilities perform a rigorous hazard and risk analysis based on either ANSI/ISA-84.00.01 or IEC 61511 safety standards to determine the level of protection required for each hazard in the plant. This paper describes the application and implementation of three (3) unique safety instrumented systems developed by Hatch for ensuring the safe operation of three different pressure oxidation processes.

Jan 1, 2014