Search Documents

By K. Yamaguchi

To contribute highly efficient and environmentally conscious copper smelting process, several topics in chemistry of the continuous converting were discussed. Through the reviewing the authors' thermodynamic simulations, it is recognized that small amount and low copper content of the coexisting slag is preferable. Some discussions were added to the Takeda's diagram for Cu20-Fe0x-Ca0 ferrite slag, and the activity curves of the constituents were derived. Thermodynamic calculations were carried out on the copper contents of the slag during the blister copper formation. The dissolution of copper in slag decrease somewhat with increasing temperature, but the effects of increasing S02 pressure and decreasing %S in copper are considerable to increase in copper content of the slag. The optimum oxygen enrichment in the supplied air, and regulation of the oxidation degree for the blister copper are important in practice. The gypsum phase separation in the calcium ferrite slag was also evaluated thermodynamically, and concluded that decreasing temperature, increasing CaO content or S02 pressure, and extensive oxidation of the blister copper tend to separate CaS04. 0

Jan 1, 2007

By R. T. Jones

The largest known platinum group metal (PGM) deposit in the world is the Bushveld Complex in South Africa, with the Great Dyke in Zimbabwe also being one of the biggest. It is therefore not surprising that the majority (just over 5 million troy ounces or 156 metric tons per annum) of the world's platinum is produced in Southern Africa. Primary smelting of ore concentrates is carried out in that region by five companies, namely Anglo Platinum, Impala Platinum, Lonmin Platinum, Northam Platinum, all of South Africa, and Makwiro Platinum in Zimbabwe. The only other primary smelter of platinum group metals is Stillwater Mining of Montana, USA, although very significant quantities of PGMs are produced as co-products by Norilsk Nickel of Russia. Smaller (but still significant) quantities of PGMs are produced by Falconbridge and Inco of Canada, also as co-products from nickel sulphide smelting. There are many similarities between PGM smelting and nickel sulphide smelting, and the range of technologies in use includes six-in-line rectangular electric furnaces, three-electrode circular AC furnaces, Peirce-Smith converters, and Anglo's ACP (based on Ausmelt technology). PGMs are also recovered from residue materials using DC arc furnace technology.

Jan 1, 2005

"THE CONCEPT of energy as a commodity, while not entirely new, is not as widespread as the importance of the idea to this modern world would lead one to expect. The growth in the supply and use of energy over the past years has been tremendous, but our very closeness and familiarity have somewhat distorted the viewpoint, particularly of the younger generation. To many of us who remember the wonderful satisfaction of our first responsibility for directing two horsepower hitched to a farm cart or hay wagon, there still arises a feeling of some awe at the casual flick of the switch with which our sons and daughters summon to their convenience the service of some one hundred or more horsepower.Energy is the vital component of our existence and, no matter what contempt our day-to-day familiarity may •breed, it is wise to .pause from time to time and consider our national energy standing. Have we still capital in the bank? Are our expenditures wisely •conceived and well directed? Is provision being made for the years •ahead for the needs of our children and our children's children?"

Jan 1, 1953

By K. Yamaguchi

To contribute highly efficient and environmentally conscious copper smelting process, several topics in chemistry of the continuous converting were discussed. Through the reviewing the authors' thermodynamic simulations, it is recognized that small amount and low copper content of the coexisting slag is preferable. Some discussions were added to the Takeda's diagram for Cu20-FeOx-CaO ferrite slag, and the activity curves of the constituents were derived. Thermodynamic calculations were carried out on the copper contents of the slag during the blister copper formation. The dissolution of copper in slag decrease somewhat with increasing temperature, but the effects of increasing S02 pressure and decreasing %S in copper are considerable to increase in copper content of the slag. The optimum oxygen enrichment in the supplied air, and regulation of the oxidation degree for the blister copper are important in practice. The gypsum phase separation in the calcium ferrite slag was also evaluated thermodynamically, and concluded that decreasing temperature, increasing CaO content or S02 pressure, and extensive oxidation of the blister copper tend to separate CaS04.

Jan 1, 2007

By N. R. Paterson, D. G. MacKay

"The geology of the Mattagami mining camp, while of particular economic significance, is unfortunately obscured by a very thick mantle of overburden. For this reason geo-physical methods have been relied upon heavily in exploring the area. Geophysical data over five important sulphide discoveries show how targets are selected for drilling and how effective geophysics has been in assisting subsequent development programs."

Jan 1, 1960

By L. Shasko, M. Hurlbert

As climate change is increasingly perceived as a problem, and fossil fuel based power production options are increasingly limited through regulatory restrictions and public distaste, future options become constricted. Reflexivity and social learning elicited through qualitative and mixed research methods offer important insight into what future power production pathways might be. Given factors of cost, baseload requirements, and energy density, options such as nuclear may be increasingly accepted. This paper explores this literature and possible methods of pursuing the reluctant acceptance of nuclear energy.

Jan 1, 2020

By Walter Nelson

Considerable thought and discussion had been devoted toward provision for increased milling capacity at the Allenby concentrator of The Granby Consolidated Mining, Smelting and Power Company operations as early as 1940. During the war, plans for the installation of an additional grindi.ng unit were formulated but were not carried out. It took considerable time after the war to prepare the mine again for its highest rate of production since, with the scarcity of men, development work had been sacrificed in favour of maximum ore shipments. In order to prepare for the expected competitive market in copper, the matter of increasing the capacity of the concentrator was again given serious attention. As ore became available in the mine and the output of the mill was increased, limitations for a satisfactory recovery were observed, due to the overloaded condition of the classifier units at the higher tonnages. From a metallurgical standpoint, the ore from the Copper Mountain mine had always been difficult to treat on account of the finely disseminated character of much of the mineralization and the difficulty of grinding to the desired fineness. This trouble has become aggravated with time as an increasing amount of wall-rock has diluted the ore and lower grade orebodies have been mined. It therefore has been, and is, the practice at the concentrator to maintain the maximum amount of reduction in size of material fed to the flotation units as is possible for the daily tonnage to be milled. This means that all the grinding units are operated for the maximum possible time, and that the classifiers are regulated to return as much feed ?as possible to the mills. The number of tons to be milled for ?the day is determined by the concentrator superintendent after ascertaining the availability of ore from the mine, the condition of the concentrator ore bins, and the need for repairs in the rolls plant. In order to maintain the tonnage des1red, hourly estimates are made of the rate of grinding by weighing the amount of ore contained on one foot of each of the belts conveying the feed to the various ball-mills, and adjustments are made accordingly.

Jan 1, 1950

By R. R. Song, Q. Li, H. Xing, X. C. Wei

Geomechanical modelling of fault stability is an important part of CO2 capture and storage (CCS) research program to ensure its viability and long-term safety. Storage of CO2 in deep subsurface reservoirs requires estimates of sustainable fluid pressures that will not induce fracturing or fault reactivation which could cause fault slip. More importantly, fault slip gives rise to seismic waves, which inflict severe damage to the cap rock of the reservoirs and may result in leakage pathways for the buoyant plume and thus compromise the integrity of seal formations. In this study, we generated a numerical model tuned towards conditions usually encountered in the Shenhua CCS demonstration project in Ordos basin. In particular, with the purpose of evaluating the sensitivity of the parameters as well as their relationships with the moment magnitude of the seismicity, a variance-based sensitivity analysis was adopted for importance ranking of the uncertain input parameters of the given model. However, such flow models could involve one or several spatial inputs, for instance, fault dip, distance between fault and the injection well, friction angle of fault, permeability of fault, Young's Modulus of fault, injecting pore pressure and the stress field. Studying the sensitivity to each of these spatial inputs motivated the present work. The results led to the following conclusions: fault depth and fault dip significantly affect the behavior of the fault and the fault slip becomes violent with the fault depth increasing and fault dip decreasing. Furthermore, the results indicate that slip time increases with the fault dip decreasing and decreases with permeability of fault increasing. In addition, the calculation of seismic moment and moment magnitude of an earthquake demonstrates that it rises significantly with the decrease of fault dip and the increase of fault depth, and it decreases with the rising stress field. The results show that variations of the only controllable parameter injection pressure do not show great influence to the fault behavior compared with other geological factors, which imply site selection is extremely important for the CCS projects.

Jan 1, 2015

By S. N. Yu

Tele-operation manipulators applied in this paper are systems for the remote handling and management of pyroprocessing related facilities in an Argon cell of the KAERI (Korea Atomic Energy Research Institute). Generally, these kinds of systems are composed of a master-slave system and its peripherals installed along the wall of the cell, with the master transmitting the user?s own motion to the gripper directly. This study introduced various considerations and modifications to improve the remote handling performance. The analysis of an operator's ability using his/her own upper arm motion range while manipulating the MSM, and considerations of its manipulation margin and the related tool modifications are also included. Finally, the test results of several remote handling tasks are presented, and an adequate operation strategy for the tele-operation system of hot-cell type facilities is proposed.

Aug 1, 2013

By P. Duran

The metallurgical gas handling system at Chagres Smelter, like that of many smelters, can be the limiting constraint to processing more concentrate through the smelter. Mass and energy balances for the metallurgical gas handling system processing off-gases from the flash furnace and Peirce-Smith converters have been used by both operations and process engineering groups to help evaluate different operational scenarios in which the use of the installed capacity could be maximized and/or an operational strategy can be change with the purpose of removing a bottleneck or justifying an investment to relieve a constraint in the gas handling system. The present work describes the development of these process balances that were carried out in Exce®. The results were validated with operational data and, subsequently, some cases of industrial interest were simulated, detecting some conditions that were limiting the operation due to the present installed capacity in the Chagres Smelter.

Jan 1, 2007

Waste rock extracted from a mine is typically stored nearby on the surface. Such waste rock piles must be designed to ensure their geotechnical and geochemical stability during the mine operation and after closure. The optimal construction of a pile requires detailed planning. Deposition should involve benches of limited height to control the global slope angle, based on the long term factor of safety. It can also be advantageous to compact the top of each bench and to give the surface an outward inclination to control water flow by limiting infiltration and favoring lateral diversion. When part of the waste rock contains reactive minerals, it is also deemed necessary to use selective placement with the non-reactive portion to prevent direct exposure to natural conditions. The construction must be well documented, and include data from the monitoring program. These and related aspects are presented and discussed in the paper.

Aug 1, 2013

By Juliana Parreira

The past decade shows record increases in global demand for minerals and metals with an accompanying significant decline in skilled personnel. Mining companies today are examining new technologies to maximize production, reduce costs, and create safer work conditions to deal with this shortfall. Automation of an open-pit mine haulage system is receiving attention as a beneficial option since it provides more consistent and efficient operation of mining equipment, it removes workers from potential danger, it reduces fuel consumption significantly reducing greenhouse gas (GHG) emissions, and it can help optimize vehicle repairs and equipment replacement because of more-predictable and better-controlled maintenance. This paper describes a simulation model under development using the EXTENDSIM software package to examine scale-up issues and constraints of autonomous vehicles in comparison to a manual system. The software can predict and manage Key Performance Indicators (KPIs), such as productivity, safety, cost, equipment failures, fuel consumption, and tire wear under different road and load conditions. By breaking-down the various systems of an autonomous haulage truck and simulating the overall haulage system using a Monte Carlo approach, the model becomes a flexible and powerful tool to use within a mining organization. Direct comparison to a manuallyrun system can be done to show the cost and operational benefits of automation. Project managers can use this tool to guide decision-making about possible application of autonomous haulage trucks at a specific mine site.

May 1, 2010

By P. R. G. Brandão, E. E. Ferreira

The presence of metallic cations in solution will affect the aggregation or dispersion of the fine hematite particles, depending on the type of cation adsorption: either specific or non specific adsorption. In this work, the zeta potential measurements were carried out on a sample of pure hematite as a function of pH and metallic cations concentration (Ca2, Mg2+, Mn2+, K+, Na+ and Al3+). The objective of these studies was to clarify the effect of these metallic cations on the surface chemical properties of pure hematite. The cations K+ and Na+ adsorbed as non-specific species and caused only the reduction on the values of zeta potential (in terms of absolute value) over the entire range of pH values tested. For the Al3+ cation, in the acidic pH range it adsorbed as a specific species and increased the zeta potential values. The cations Ca2+, Mg2+ and Mn2+, adsorbed as a non specific species at pH levels less than 6.0 and caused the reduction of zeta potential due to the compression of the electrical double layer. However, for pH values greater than 6.0, these cations adsorbed as a specific species causing the zeta potential to increase and became more positive as the pH value increased (alkaline). This effect could be due to the adsorption of some hidroxy complex species of these cations, which contributed to the positive charge. The effect of metallic cations (Ca2+, Mg2+ and Al3+ concentration, at pH 4.0, 7.0 and 10, showed the following results: a) at pH 4.0, increasing the concentrations of Ca2+ and Mg2+ resulted in on a small reduction in the value of the zeta potential. At this pH, increasing the concentration of A131 cations caused the zeta potential to increase due to specific adsorption of a negatively charged Al3+ hydroxy complex b) at pH 7 and 10, increasing the concentrations of Ca2+ and Mg2+ caused the zeta potential to change its charge from negative to positive.

Jan 1, 2004

By F. D. Aaring

"IntroductionTHE PINCHER CREEK gas condensate field, in Township 3, Range 28, and Townships 3 and 4, Range 29, West of the Fourth Meridian, was discovered in 1947 by the Canadian Gulf Oil Company with the completion of Pincher Creek No. 1 well in the Madison lime-stone of Mississippian age.This discovery was the result of a great deal of detailed seismic work in the area and is a credit to the geophysical personnel of the Company. The depth of the reservoir varies from 7,400 feet to 8,200 feet subsea, with the established water level at -8,200 feet. The predicted depth was but a scant 100 feet from that found in the discovery well, at 11, 705 feet. Since the discovery of the reservoir, three additional wells have penetrated the Madison limestone and have further verified the original •seismic interpretation of the limits of this reservoir.To date, •only a very small amount of gas has been produced from this field. Consequently, the reservoir studies that have been made so far are predominantly based on investigations of the phase behaviour of the fluid and physical characteristics of the reservoir rock. In view of the above limitations, it has been necessary to set up and perform model reservoir studies with the fluids and to recover as much core from the productive Madison limestone as possible in order that it might be analysed by conventional laboratory technique and be subjected to detailed microscopic geological examination."

Jan 1, 1952

By Tong Qin, Jinxia Zhang, Fusheng Niu, Limei Bai

"The interaction between a deformable bubble and a rigid particle in viscous liquids under microgravity conditions is studied by direct numerical simulation via an Arbitrary-Lagrangian-Eulerian (ALE) method. Due to the microgravity, the bubble will stay as a sphere in the fluid without external forces and its deformation is caused by the moving particle. In this study we assume the flow field is axisymmetric and the motion of the gas inside the bubble is neglected. The particle equations and the Navier-Stokes equations for the fluid are solved in a unified finite element framework. The particle obtains an impact velocity by an external force and the impact velocity is varied over a wide range. A ‘critical time scale’ T0 was identified for the interaction process. For successful contacts between particle and bubble, the time scale of their relative motion must be less than T0.INTRODUCTIONThe particle-bubble interaction is an important process in many applied industrial domains such as water treatment, froth flotation and liquid steel purification. It is a complex three phase process in that it embraces many research areas: fluid hydrodynamics, interfacial forces, particle and bubble behaviour and solution chemistry.Derjaguin and Dukhin(1961) clarified the particle-bubble interaction by introducing three-zone model for small and medium size particles. When the particle is far away from the bubble surface, the hydrodynamic forces are dominant. The particle is driven toward the bubble surface by the particle inertial and gravity. This region is regarded as Zone 1 and the interaction in this zone is a collision subprocess. As the particle gets close to the bubble, it exits a zone where the liquid flow around the bubble surface creates a tangential stream from the upper surface of the bubble toward the rear of the bubble. This is Zone 2 which is called the diffusiophoretic zone. In Zone 3, the particle is very closed to the bubble, surface forces like van der Waals, electrostatic and structural forces are considered. Contrast to Zone 1, Zone3 can be regarded as an attachment subprocess."

Jan 1, 2016

By Z. Zhao, B. Li

"Fractures are the key channels for fluid flow and mass transport in fractured rocks of low/negligible matrix permeability. In single rock fractures, surface roughness causes fluid flow in tortuous paths, and reduces the overall fracture conductance. A number of empirical models have been proposed to relate the reduced hydraulic aperture to the mechanical aperture due to surface roughness, which were revisited and compared. Using two of those relationships between hydraulic apertures and mechanical apertures, we studied the influences of local surface roughness of fractures on fluid flow and solute transport processes at the macroscopic scales of fracture networks. The results show that fracture roughness can affect the flow rates and residence time to varying extent, mainly depending on the empirical models between hydraulic apertures and mechanical apertures. However, fracture roughness has negligible influences on the general patterns of fluid flow (channeling) and solute migration (e.g., travel paths and shape of breakthrough curves). This is because the connectivity of a fracture network is mainly determined by other geometrical parameters (fracture positions, orientations, and lengths), rather than roughness or apertures. INTRODUCTIONIn fractured crystalline rocks of low or negligible matrix permeability, fluid flow and contaminant migration mainly occur within the connected fractures. An understanding of fluid flow and contaminant migration in fractured rocks is a crucial issue in many deep underground projects, e.g. underground repositories for radioactive waste, CO2 sequestration, enhanced geothermal systems, oil and gas production, etc. Rock fractures are typically rough-walled, and surface roughness appears to have first order control on the mechanical and hydraulic behavior of single rock fractures (Boutt et al., 2006).It is well known that the mechanical aperture of a rock fracture is usually larger than its hydraulic aperture, due to fracture surface roughness (Tsang and Witherspoon, 1983). However, for naturally fractured rocks including numerous discontinuities, the effects of this reduced hydraulic aperture in local fractures on macroscopic fluid flow and solute transport in complex fracture systems still remain unclear. Many previous studies assumed identical hydraulic and mechanical apertures in discrete fracture network models for simplicity (Min et al., 2004; Zhao et al., 2011). Therefore, the main objective of this study is to evaluate the influences of local surface roughness of fractures on fluid flow and solute transport processes at the macroscopic scales of fracture networks, by employing the empirical models that relate the hydraulic aperture to the mechanical aperture."

Jan 1, 2015

By Jin-Hwa Song

Rolling temperatures and cross rolling ratios were varied to investigate the effect of crystallographic texture of alpha-phase on the anisotropy of mechanical properties in modified Ti-6A1-4V alloy. Hot rolling method was unidirectional and cross rolling, during which the rolling temperature was in the range of 830°C and 920°C. Cross rolling ratios were varied from 0.3 to 1.0 at 875°C. For unidirectional rolling, as the rolling temperature increased texture changed from the mixed basal and transverse texture to the simple transverse texture. Contrary to other work, it was observed that the maximum intensity of transverse components increased with the increase in rolling temperature. For cross rolling, on the other hand, the transverse texture component was almost suppressed at 830°C, giving rise to a symmetrical basal texture. With increasing cross rolling temperature, the transverse texture components developed again. A simple transverse texture, which showed two maxima appearing circularly 90° apart, was observed at 920°C. It was found that unidirectional rolling could not eliminate the transverse texture, which resulted in the anisotropy of mechanical properties. The anisotropy of mechanical properties obtained from tensile and V-notch Charpy test was closely related to the crystallographic texture and its intensity at each rolling condition. To obtain the isotropy of mechanical properties by cross rolling, it is suggested that cross-rolling ratios should be controlled above 0.5. The variation of rolling temperatures and directions has great influence on the anisotropy of impact value rather than tensile strength.

Jan 1, 2004

By A. E. M. Warner, P. J. Mackey

"In 1988, two of the present authors Warner and Vahed [1] were amongst several co-authors on a seminal paper reviewing nickel pyrometallurgical operations of the era. Given that significant changes in the nickel industry have occurred since that time, including the overall political landscape, technology, the overall world energy picture, the countries sourcing nickel and finally the nickel market itself, the present authors considered it timely to provide a 2015 update. In 1988, total world nickel production from sulphide and laterite sources, including production in the former "Centrally Planned Economies"- was about 0.86 million tonnes/a, while in 2014 total world nickel production reached an all-time high of almost 2 million tonnes/a - some 230% higher. On the other hand, while in 1988, about 94% of world nickel was produced pyrometallurgically and of the order of 33% via laterites, today, about 88% of nickel is by pyrometallurgy, with some 41% from laterites, thus showing that more nickel is now sourced from laterites, a trend which is expected to continue.During the period under review, new processing technologies were developed and introduced, along with substantial improvements in both the technologies employed and the scale of operations. Significant productivity gains have been achieved in sulphide pyrometallurgy in part through more efficient mineral processing, particularly in pyrrhotite rejection, and the use of ever larger-scale process equipment. This made it possible to treat lower grade and more complex ores. The significant game-changer from a production perspective was the introduction in the early 2000s of nickel pig iron (NPI) in China via modified iron blast furnace smelting, an old technology long ago cast aside by other nickel producing countries. With the exception of the emergence of this new NPI capacity in China, in the laterite industry modernization and expansion of existing operations has been employed to gain productivity, to cut costs and/or offset the effect of declining ore grades. The NPI technology development has become a game changer in the traditional global supply and demand relationship, opening up a new frontier to supply nickel to low grade utility steel producers. One other key nickel development was the Indonesian ban on nickel ore exports effective in January 2014, thus effectively curtailing NPI production at existing Chinese plants, but on the other hand, potentially prompting new smelting facilities in Indonesia. This paper reviews and updates major pyrometallurgical sulphide and laterite operations worldwide, including changes in nickel extractive metallurgy. It also provides a brief review of new developments in pyrometallurgical operations, with special focus on the NPI process and presents an outlook of the potential future direction of the industry."

Jan 1, 2015

By Ralph D. Parker

THE subject matter of this paper will be primarily restricted to the metallic mineral industry, which last year was responsible for almost 60 per •Cent of the total value of Canada's mineral production. It has been written that, in the broad sweep of eternal time, sixty years is as transient as a flicker of lightning in a summer night's sky. In the history of mankind and human endeavour, however, six decades can encompass momentous events and far-reaching •circumstances, all of which affect the lives of men and change the destiny of nations. This observation is con-firmed very positively by a study of our Canadian mining history, from either the broad viewpoint of human progress or the more specialized viewpoint of national economy. The past sixty years have witnessed vast changes in the economic importance of mining in this country's affairs, and also in the technology of the industry. Mining has emerged from the days of rule-of-thumb practice and is now taking on the stature of a highly diversified science.

Jan 1, 1962

By John F. Kearney

After World War II Canada?s fledgling iron ore mining industry developed along the ill-defined Quebec / Labrador border near what became the town of Knob Lake and later renamed Schefferville. For about twenty-five years from 1954 to 1982 Schefferville was the epicenter of Canadian iron ore mining and the foundation of the Iron Ore Company of Canada. In about 1982 it all stopped, shut down, the miners moved away leaving behind a mining camp and a ghost town that have sat idle and almost deserted for the past twenty five years. The story looks set to change with new plans to re-establish the former mining operations in the historic mining camp. This paper outlines the proposal to reactivate the direct shipping iron ore operations in the Schefferville mining camp, and specifically the properties in Labrador owned or optioned by Labrador Iron Mines Limited (?LIM?), a wholly owned subsidiary of London Stock Exchange listed Anglesey Mining plc. The Schefferville mining camp is located about 1,000 km northeast of Montreal. There are no roads connecting the area to southern Labrador or to Quebec. Access to the area is by rail from Sept Iles to Schefferville, or by air from Montreal and Sept Iles.

May 1, 2007