Search Documents

By C. C. Miller, A. B. Dyes

The cost of finding and developing new reserves is continually rising. We must meet these rising costs with more economical operations. This can he accomplished if we revise our ideas of proper well spacing and well allowable to consider the concept of optimum well spacing. According to this concept, the optimum spacing is the one which leads to the maximum present worth for a reservoir when ail factors affecting total cost and total revenue are considered and when the wells are produced in the most eficient manner. Application of this principle efficiently utilizes available well potential and properly considers the recovery eficiency in addition to fixing the spacing on the basis of the amount and value of the oil to he recovered. This Study presents an analysis of one producing zone containing low gravity crude to illustrate the effect of these factors on the present worth and on the optimum economic spacing under two production drives—-evolved gas and water drive. The maximum present worth occurs when the optimum number of wells for open-flow operation is employed. Frequently, this optimum development cal1s for very wide spacing and the ideal field rates are not unreasonable. Under other circumstance. where proration is necessary, an optimum combination of well spacing and well allowable exists which permits production at relatively high rates. The optimum well density in a field depends on the recovery efficiency and the valule of the oil. In solution gas-driven reservoirs this optimum spacing for operation at high producing rates can vary from extremely wide spacing to handle viscous low gravity oil in thin formations to relatively close spacing in thick sands where good recoveries are expected. Because of the better recovery from water-driven fields, the optimum spacing in these fields is closer than in solution gas-driven fields. Also, the water encroachment pattern is dependent upon the well spacing, and an adequate numher of wells is needed to assure a good sweep eficiency. The economic optimum well density in a water-driven field is high enough for this purpose. INTRODUCTION From year to year domestic oil becomes more difficult to find. The fields we do locate are frequently smaller and deeper than older fields and the costs for men, material and equipment are continually rising. To replenish our reserves we must continue to search for and develop new fields, but experience has shown we cannot expect prices to rise in proportion to costs. Consequently, we must meet increasing costs by more economical operations. A vigorous effort is being made within the industry to improve exploration methods, to cope with the problems of deeper drilling, and to obtain a secondary yield from older fields. Many significant contributions have resulted from these efforts. The economic operation of new fields can be further improved by developing these fields on optimum spacing and producing the wells at higher rates. This would avoid the drilling of unnecessary wells and provide additional capital for seeking new oil. While the benefits of these practices are obvious, the problem of defining the optimum development of a field for natural depletion can become very complex. A study of the effect of well spacing and several reservoir variables on economic worth of a specific field is reported here to illustrate the problem and to show the magnitude of the benefits to be realized. This study is necessarily limited to the field conditions selected and is not intended as a general solution of the well spacing problem. It does, however, indicate factors to be considered, the trends to be expected, and the direction in which we should proceed in developing new fields. NO consideration is given to land and legal considerations which might arise. METHOD OF ANALYSIS The optimum method of developing and producing a field is to use the combination of spacing and prora-tion which gives the maximum return. In addition, we do not want to lose recovery. These considerations of maximum return and maximum recovery present no serious conflict. The value of each method of operation is conveniently expressed in terms of its present worth. According to the present worth method of evaluation,' an acceptable annual percentage return is assigned to the operation, and all incomes, capital costs, and expenses are discounted at this rate to the start of the operation. This net value is the present worth. If we apply the same discount rate to several alternate methods of operation, the one yielding the greatest present worth is the best method. If we express net income in terms of price per barrel of oil produced, drilling and equipment costs on a well basis, and expenses as cost per well year, this evalu-

By I. Hawke, K. Barron

I. Hawkes (Postgraduate School in Mining, University of Sheffield, Sheffield, England) — The photoelastic stressmeter is proving to be a very practical tool for 'in-situ' measurements in the fields of civil and mining engineering and Barron's article has therefore come at a very opportune time, supplementing as it does, the considerable amount of laboratory and field data which is being accumulated.1,2,3 There are however several points relating the application of Barron's conclusions to the practical use of the meter which require further elucidation. EASE OF READING If the photoelastic stressmeter is to have a wide application, the fringe orders must be easily measured. The system adopted by the writer and his colleagues at Sheffield for the uniaxial stress case is to read the fringe order at the 45 point, 0.20 in. from the center (11/4 in. diam meter). This procedure has been recommended because the fringes not at this point form a very distinct 'eye' which is obvious even to those who have had little experience with photoelastic fringe patterns. Barron points out that this point can also be used up to a stress ratio of 0.33 and in practice this is normally done. In biaxial fields above a ratio of 0.33 the 'eye' is no longer apparent and the fringe order must be ascertained at some other point. The writer and his colleagues experimented at various points and finally chose a point at a distance 0.175 in. (11/4 in. diam meter) on the minor stress axis and fixed this point on the meter by inserting a collar of this diameter. This procedure enables the 'eye' technique to be used for uniaxial stresses as the 'eye' falls outside the collar; any other technique for biaxial patterns would require lines to be engraved on the meter itself and reading difficulties would be experienced by all but the most highly trained. It is interesting to point out that in a great many field applications ranging from underground pillars to building foundation piles the stresses measured have been uniaxial. In such cases, reading the fringe order has been simple even for unskilled persons. SENSITIVITY The photoelastic stressmeter acts as an inclusion, and as such its theoretical behavior is as described by Barron's mathematical analysis. When considering its practical application, however, it must be remembered that rocks and concrete are not mathematically ideal substances. The theory relates the fringe order in the meter to the stresses and the E (Young's Modulus) and the µ (Poisson's Ratio) values of the surrounding material. There is of course no unique E or µ value for rocks or concrete. These values change both with stress level and time load application sometimes to the order of 300%. We at Sheffield have very accurately calibrated the photoelastic stressmeter in a wide range of materials and have also measured the average E values for these materials. The results prove that the meter sensitivity

Jan 1, 1965

by their overdogmatic picture of geology and their resulting drastic oversimplification and idealization of geologic features. I am in hearty disagreement with the recommendation that geophysics should be done by cooperative work between a geologist and a geophysi-cist. That arrangement would be comparable to doing petrography by having a physicist at the microscope and a geologist sitting by his side. The interpretation of the geological significance of geophysical data can be done efficiently only by a physicist who has become also a good geologist or by a geologist who is also a good geophysicist. Less Well-trained Men The rank and file, composing perhaps two-thirds of the personnel of exploratory geophysics, is not, and should not be, composed of highly trained men. The routine, stereotyped character of the work and the impossibility of promotion of more than a few from these lower ranks even under the best circumstances justify companies in filling the bulk of these rank and file positions with men having only a bachelor's degree at the most. There can be a wide range of training for such positions, although certain lines of study are preferred for certain kinds of work, and different employers have different preferences. For work in gravitational and magnetic prospecting, first preference will be for men having geological training and second for men with civil engineering training. In seismic work, men with geological training are preferred by some employers for computers; physicists, electrical engineers and all whose technical education has covered radio circuits are preferred for the other technical positions. Collegiate training in geophysical prospecting brings no preference and by many employers is given a slightly inferior rating. One large company seldom hires men who have just graduated with a major in geophysical prospecting. This prejudice is based on the reasoning that much of what is learned in college is obsolete or obsolescent, that most of the techniques learned in college will have to be unlearned, because different from those used by the employing company, and that in the long run additional courses in basic physics, mathematics and geology are of more value to a man than the courses on geophysical prospecting. DISCUSSION [This discussion refers to the five papers beginning on page 23 and ending on page 74.1 L. W. Blau,* Houston, Texas.—I have had some rather sad experiences with forecasting. For example, I could not foresee 10 years ago my present occupation, and I do not profess to be able to look ahead 10 years and tell anyone what he will be doing then. Referring to the point raised in the discussion, I do not know, for example, what the price of oil will be 10 years from now. If an appreciable number of

Jan 1, 1940

By Donald C. Branford

The place of geophysics in the curriculum of a college or an engineering school has been much discussed. There is uncertainty as to whether the graduate may be called a "geological geophysicist" or a "geophysical geologist." Some have used the term "geophysical engineer." The question of the specialized undergraduate curriculum versus a general undergraduate training in the parent sciences with the addition of cultural electives has been and is still being argued. The literature during the past Io years shows that there are two rather definite schools of thought on this subject. The prospective employer, engaged in active geophysical exploration, visualizes the graduate in terms of the routine work he will do in the field. The school administrator, grounded in many years of tradition in the cultural type of education, visualizes the graduate in terms of his position in a political and cultural society as well as in his work as a professional geophysicist. Both are right and both wrong. A third school of thought, that of the student himself, has been almost totally ignored. It would seem best, for the purpose of this paper, to treat these various points and allied material separately, and then to integrate the conclusions as a set of conditions that should be fulfilled as far as possible in the ideal curriculum. At the end the relationship of our findings to the curriculum that has been tentatively adopted at the University of Pittsburgh will be considered. Divisions in Definition or Field of Geophysics Geophysics is that field of science in which geological and earth problems are solved with the use of physical and chemical techniques. Altogether too much attention has been paid to the artificial separation in this science of the commercial applications from the so-called "pure" or academic geophysics. The only real difference in the two types of work is one of scale of operations. In the commercial field the scale is large in terms of fmancial backing, immediate economic importance, and speed of operations. In the academic field the scale is large in terms of breadth of interests, in eventual economic importance, and length of time allowable for theoretical investigations. In exploration work the scale is small in terms of dimensions, since the methods are applicable only to the outer 20,000 ft. or SO of the earth's crust. In academic work, the student is not pressed for results of immediate economic importance, and therefore can afford to spend more time on problems that seem unimportant at the time. In the sense of background knowledge of the parent sciences necessary to the geophysicist, no essential difference can be found. Physics, chemistry, geology, and mathematics together, and in their proper proportionate amounts, form the matrix from which geophysical ideas and methods may spring.

Jan 1, 1946

By Donald C. Bradford

THE place of geophysics in the curriculum of a college or an engineering school has been much discussed. There is uncertainty as to whether the graduate may be called a "geological geophysicist" or a "geophysical geologist." Some have used the term "geophysical engineer." The question of the specialized undergraduate curriculum versus a general undergraduate training in the parent sciences with the addition of cultural electives has been and is still being argued. The literature during the past 10 years shows that there are two rather definite schools of thought on this subject. The prospective employer, engaged in active geophysical exploration, visualizes the graduate in terms of the routine work he will do in the field. The school administrator, grounded in many years of tradition in the cultural type of education, visualizes the graduate in terms of his position in a political and cultural society as well as in his work as a professional geophysicist. Both are right and both wrong. A third school of thought, that of the student himself, has been almost totally ignored. It would seem best, for the purpose of this paper, to treat these various points and allied material separately, and then to integrate the conclusions as a set of conditions that should be fulfilled as far as possible in the ideal curriculum. At the end the relationship of our findings to the curriculum that has been tentatively adopted at the University of Pittsburgh will be considered. DIVISIONS IN DEFINITION OF FIELD OF GEOPHYSICS Geophysics is that field of science in which geological and earth problems are solved with the use of physical and chemical techniques. Altogether too much attention has been paid to the artificial separation in this science of the commercial applications from the so-called "pure" or academic geophysics. The only real difference in the two types of work is one of scale of operations. In the commercial field the scale is large in terms of financial backing, immediate economic importance, and speed of operations. In the academic field the scale is large in terms of breadth of interests, in eventual economic importance, and length of time allowable for theoretical investigations. In exploration work the scale is small in terms of dimensions, since the methods are applicable only to the outer 20,000 ft. or so of the earth's. crust. In academic work, the student is not pressed for results of immediate economic importance, and therefore can afford to spend more time on problems that seem unimportant at the time. In the sense of background knowledge of the parent sciences necessary to the geophysicist, no essential difference can be found. Physics, chemistry, geology, and mathematics together, and in their proper proportionate amounts, form the matrix from which geophysical ideas and methods may spring.

Jan 1, 1942

By Donald C. Branford

The place of geophysics in the curriculum of a college or an engineering school has been much discussed. There is uncertainty as to whether the graduate may be called a "geological geophysicist" or a "geophysical geologist." Some have used the term "geophysical engineer." The question of the specialized undergraduate curriculum versus a general undergraduate training in the parent sciences with the addition of cultural electives has been and is still being argued. The literature during the past Io years shows that there are two rather definite schools of thought on this subject. The prospective employer, engaged in active geophysical exploration, visualizes the graduate in terms of the routine work he will do in the field. The school administrator, grounded in many years of tradition in the cultural type of education, visualizes the graduate in terms of his position in a political and cultural society as well as in his work as a professional geophysicist. Both are right and both wrong. A third school of thought, that of the student himself, has been almost totally ignored. It would seem best, for the purpose of this paper, to treat these various points and allied material separately, and then to integrate the conclusions as a set of conditions that should be fulfilled as far as possible in the ideal curriculum. At the end the relationship of our findings to the curriculum that has been tentatively adopted at the University of Pittsburgh will be considered. Divisions in Definition or Field of Geophysics Geophysics is that field of science in which geological and earth problems are solved with the use of physical and chemical techniques. Altogether too much attention has been paid to the artificial separation in this science of the commercial applications from the so-called "pure" or academic geophysics. The only real difference in the two types of work is one of scale of operations. In the commercial field the scale is large in terms of fmancial backing, immediate economic importance, and speed of operations. In the academic field the scale is large in terms of breadth of interests, in eventual economic importance, and length of time allowable for theoretical investigations. In exploration work the scale is small in terms of dimensions, since the methods are applicable only to the outer 20,000 ft. or SO of the earth's crust. In academic work, the student is not pressed for results of immediate economic importance, and therefore can afford to spend more time on problems that seem unimportant at the time. In the sense of background knowledge of the parent sciences necessary to the geophysicist, no essential difference can be found. Physics, chemistry, geology, and mathematics together, and in their proper proportionate amounts, form the matrix from which geophysical ideas and methods may spring.

Jan 1, 1946

by their overdogmatic picture of geology and their resulting drastic oversimplification and idealization of geologic features. I am in hearty disagreement with the recommendation that geophysics should be done by cooperative work between a geologist and a geophysi-cist. That arrangement would be comparable to doing petrography by having a physicist at the microscope and a geologist sitting by his side. The interpretation of the geological significance of geophysical data can be done efficiently only by a physicist who has become also a good geologist or by a geologist who is also a good geophysicist. Less Well-trained Men The rank and file, composing perhaps two-thirds of the personnel of exploratory geophysics, is not, and should not be, composed of highly trained men. The routine, stereotyped character of the work and the impossibility of promotion of more than a few from these lower ranks even under the best circumstances justify companies in filling the bulk of these rank and file positions with men having only a bachelor's degree at the most. There can be a wide range of training for such positions, although certain lines of study are preferred for certain kinds of work, and different employers have different preferences. For work in gravitational and magnetic prospecting, first preference will be for men having geological training and second for men with civil engineering training. In seismic work, men with geological training are preferred by some employers for computers; physicists, electrical engineers and all whose technical education has covered radio circuits are preferred for the other technical positions. Collegiate training in geophysical prospecting brings no preference and by many employers is given a slightly inferior rating. One large company seldom hires men who have just graduated with a major in geophysical prospecting. This prejudice is based on the reasoning that much of what is learned in college is obsolete or obsolescent, that most of the techniques learned in college will have to be unlearned, because different from those used by the employing company, and that in the long run additional courses in basic physics, mathematics and geology are of more value to a man than the courses on geophysical prospecting. DISCUSSION [This discussion refers to the five papers beginning on page 23 and ending on page 74.1 L. W. Blau,* Houston, Texas.—I have had some rather sad experiences with forecasting. For example, I could not foresee 10 years ago my present occupation, and I do not profess to be able to look ahead 10 years and tell anyone what he will be doing then. Referring to the point raised in the discussion, I do not know, for example, what the price of oil will be 10 years from now. If an appreciable number of

Jan 1, 1940

By R. H. Richman, F. Borik

A 0.3 pct C-12 pct Cr-6 pct Ni steel was rolled to 93 pct reduclion in area as austenite at 510°C, and then partially transformed as desired to ~rlartensite by qnenching to - 196°C. Pole figures for the austenitic matrix and for the martensitic product were separately determined by an X-ray transmission method. The deforitration texture of' the warm-worked austenite is characlerized by (110)(225) components, and is thus closely similar to those produced in a brasses. The pole jigure of the martensite in partially transformed material agrees well with that which can be constructed by transfortnation of the {110)(225) orientations according to either the Kuvdjuniov- Sacks or the Nishi-yatuu relatiotship. Howeuer, an important result of this construction is that me-third of the predicted orientations are missing. A graphical analysis can then be used to show that in deformed austenite certain crystallographic variants of martensite (related to the most probable austenite slip systems) are suppressed, resulting in this preferred transformation. The evidence for preferred transformation is corroborated by the measured elastic anisotropy of warm-rolled and fully transformed H-11 steel. EXTENSIVE plastic deformation of a polycrystal-line aggregate in a manner that causes flow predominantly in one direction results in a preferred orientation of the constituent crystallites. The particular orientations that are produced depend upon the crystal structure and composition of the material, as well as upon the temperature, mode, and degree of deformation; in any case, the preferred crystallo-graphic orientations, or textures, are reflected in directionality of mechanical properties. Although such anisotropy may be exploited in certain specialized applications, it is more commonly diminished or eliminated by heat treatment lest it interfere undesirably in subsequent forming operations or in structural design. In the recently developed thermomechanical treatments that significantly enhance the strength of some steels,1,2 considerable deformation of the metastable austenite prior to the martensite transformation is essential to the strengthening process. If the austenite is textured by the deformation, and if the transformation to martensite proceeds according to one of the relationships established for transformation in annealed austenite, then it must be expected that the martensite will also possess a preferred orientation even though the multiplicity of martensite orientations possible in a given austen- ite crystal will tend to restore some degree of randomness. The existence of a residual anisotropy, both mechanical 3-6 and crystallographic,' has been substantiated. In the latter crystallographic investigation, preferred orientations were determined for the martensitic structure of an SAE 4340 steel rolled 72 pct as austenite at 833°C and then quenched. However, the choice of a composition that transformed almost completely to martensite during the quench to room temperature did not permit direct measurement of the prior austenitic texture. In fact, when the "ideal orientations'' associated with well-known fcc rolling textures were converted, alone or in combination, to martensite according to the Kur-djumov-Sachs (K-s)' or Nishiyama8 relations, the agreement obtained with the observed martensite texture was only fair at best. Recently a pertinent aspect of the austenite to martensite transformation was reported by Bokros and parker,10 who found that certain habit-plane variants of martensite were suppressed by tensile deformation of Fe-31.7 Ni single crystals prior to the necessary subzero cooling. It might be anticipated that the consequences of such preferred transformation are sustained during the formation of martensite in warm-worked austenite that has a well-developed deformation texture. The present investigation was undertaken first to establish more firmly the relation between preferred orientations in plastically deformed austenite and in the resulting martensite, and second to examine the textures for evidence of deformation-induced preferred transformation. EXPERIMENTAL PROCEDURES An alloy containing 0.3 pct C, 12 pct Cr, 6 pct Ni, and the balance iron, was selected because the mar-tensite-start temperature (M,) of about -100°C allowed convenient experimental manipulation of either austenite or martensite at room temperature. Furthermore, this composition can be readily deformed as metastable austenite at moderately elevated temperatures without intervention of appreciable isothermal or athermal decomposition products. The alloy was austenitized at 1150°C, aircooled to 510°C, rolled unidirectionally at this temperature to 93 pct reduction of cross-sectional area, and finally oil-quenched to room temperature. Partial transformation to martensite was accomplished by quenching to -196°C as needed. The rolled stock was reduced in thickness from 0.067 to 0.010 in. by etching in a solution of 5 pct HC1, 45 pct HNO3, and 50 pct water, and further thinned by careful mechanical polishing to maintain the two sides of the sheet parallel within 0.0003 in. After mechanical polishing to 0.005 in., electropolishing in 1:9 perchloric-acetic acid solution produced a final thickness of 0.002 in. The preferred orientations were determined from

Jan 1, 1968

By J. W. Spretnak, J. N. Cordea

The gain boundary relaxation in high-purity aluminum, nickel, copper, and silver was studied by means of a low-frequency torsion pendulum. Both internal friction and creep at constant stress tests were conducted. A lognormal distribution in relaxation times was found to account for the relatively wide experimental internal friction peaks and the gradual relaxation behavior during the creep tests. This distribution was separated further into a lognormal distribution of relaxation time constants and a normal distribution in activation energies. A spread of up to ±6 kcal per mole in the activation energies accounted for the major part of the distribution. A "double-peak" internal friction phenomenon was observed in silver. The activation energies in kcal per mole derived from the grain boundary relaxation phenomena are 34.5 for aluminum, 73.5 for nickel, 31.5 for copper, and 41.5 for silver. It was found that the rain boundary relaxation strength in these metals increases with the reported stacking-fault energy. GRAIN boundary relaxation phenomena have been observed in a large number of polycrystalline metals and alloys. Numerous investigations have been conducted to study the structure of the grain boundary through this relaxation process. One of the first investigators was Ke1-4 who observed that the activation energy for grain boundary relaxation in aluminum, a brass, and a iron was about the same as that for volume diffusion. He concluded that the grain boundary behaved as if it were a thin liquid layer with neighboring grains sliding over one another. Leak5 conducted experiments on iron of a higher purity and observed that the grain boundary activation energy is comparable with that of grain boundary diffusion. He suggested that, in metals where this relationship holds, the damping may be caused by a reversible migration of grain boundaries into adjoining grains. Nowick6 has presented an interesting view of inter-facial relaxation with his "sphere of relaxation" model. A relaxed interface is represented as one where the shear stress is greater than the normal value along the edges and zero in the interior of the interface. The region of the stress relaxation is pictured as a sphere surrounding the interface. From his calculations Nowick concluded that the slip along an interface is directly proportional to its length. Therefore, the time of relaxation, T, depends on the size of the relaxation interface. This means that in the Arrhenius relationship, t = TO exp[H/RT], valid for atom movements, the relaxation time T is predicted to be proportional to the grain diameter through the pre-exponential term, TO. Since the internal friction can be given as Q-1 = ?j wt/(1 + w2r2), where ?J is the relaxation strength and w is the angular frequency, an increase in grain size at a constant frequency will shift the peak to a higher temperature. A great deal of work has been done to determine the exact relationship between the internal friction and grain size.1,5,7,8 In metals, the grain boundary peaks are found to be lower and broader than predicted theoretically.' The above model can explain this by a distribution in the size of the interface areas, represented by a distribution in the parameter tO, and an overlap of spheres of relaxation, represented by a distribution in activation energies. Both these phenomena result in an over-all distribution in the relaxation time, which could affect the internal friction peak height, breadth, and also position. This relationship between the experimental data and theoretical calculations appears very promising in the study of interfacial relaxation mechanisms. THEORY A lognormal distribution in t can sometimes be used to adequately describe the spectrum of relaxation times governing an anelastic relaxation. wiechert9 originally suggested such a distribution to explain the elastic after-effect in solids. This choice is particularly applicable to grain boundary relaxation when considering Saltykov's work.'' He found a lognormal distribution in the grain sizes within a metal. Recently Nowick and Berry11 have introduced a log-normal distribution in T into the theoretical internal friction equations. The form of the distribution function is where z = In(r/rm), and Tm is the mean value of t. The parameter ß is a measure of the distribution and is the half-width of the distribution when is l/e of its maximum, IC/(O). Nowick and Berry have described the methods to obtain the parameters Tm, ß, and ?,J from experimental internal friction and creep test data. In the idealized case, where only one relaxation event occurs with one relaxation time, only ?J and T are necessary to completely describe the event, and 0 = 0. For the broader internal friction curves 6 is some positive number greater than zero. The larger the 6, the greater is the half-width of the distribution in In t.

Jan 1, 1967

By P. G. Shewmon, H. E. Collins

A study has been made to determine the sites at which sulfur adsorption occurs on copper surfaces. measurements were made of the relative torques, Ys, at the intersection of twin boundaries with surfaces near the three low-index orientations, i.e., (100), @lo), and 011), over a range of H2S/H2 ratios. HZS concerztvations j'ro~n 3 to 1500pp)n between 830" and 1050°C were used. It is concluded that sulfur adsorption occurved preferentially though not exclusively at edge sites near the (100) and (110) surfaces in the HzS range — 700 Ppm giving rise to negative torques near these orientations. Beyond this HzS range, adsorption occurred at all sites. Near the (111) surface, 7/y little with HzS concentration up to approxiwzately 75pptn. Above this range, the results indicate adsorption is occurring OH both terrace and edge sites. SCIENTIFIC interest in surfaces and their interactions with a gaseous environment dates back to the beginning of the 19th century. The scientific luminaries of that period—Faraday, Maxwell, Rayleigh, Dewar, and Gibbs—were already concerned about such processes. However, it has only been within the past several decades that adsorption on metal surfaces has been actively studied. This increased interest in adsorption has been brought about by the advent of new and improved experimental techniques and apparatus, e.g., ultrahigh vacuum, and field-emission and ion microscopes. However, most of the work done using these techniques has been carried out at low temperatures. When adsorption studies have been made at either low or high temperatures, they usually gave no indication of the particular surface orientations or type of sites on which adsorption was occurring. In the last few years, there have been a series of studies in which the surface tension, y,, and/or its derivative with respect to orientation, 7, have been studied as a function of orientation and atmosphere.'-7 Nearly all of the work on the relative torque,* ~/y, silver annealed in hydrogen and air.6 Recently Winterbottom and Gjostein" have used a modified and more accurate Mykurian method to determine the y plot of gold in hydrogen The only work in which T/~, has been measured over a range of chemical potentials for a given solute, p2, is that of Robertson and shewmon7 on the Cu-0 system. They measured T/Y, vs Po, (10"" to 10- l3 atm) at 1000°C in various mixtures of Hz0 and HZ. From this work they estimated the value of p2 at which one half of the surface sites are occupied with oxygen, pg, as being in the range 10- l6 to 10- l5 atm of oxygen. They also found that increasing Pa increased the magnitude of ~/y, near the (111) and (100) orientations. This indicates that oxygen is not adsorbed preferentially at step edges, but uniformly over all surface sites. In addition, they did one experiment on sulfur adsorption on copper surfaces, which indicated that sulfur adsorption decreases ~/y, near the (100) orientation, while not affecting ~/y, near the (111). This could be interpreted as indicating that sulfur adsorbs preferentially at step edges near the (100). In this paper the primary objective of the work has been to carry out a study of sulfur adsorption on copper surfaces over a range of temperatures and p,. In conjunction with this work, thermal grooving at grain boundaries has been examined as a method of determining the effect of sulfur adsorption on y,. METHODS Ideally, one would like to have information on the quantity of solute adsorbed on a surface and the types of sites at which it is absorbed as a function of p2. The total quantity adsorbed or the surface excess is given by the thermodynamic equation Thus data on the variation of y, with pz indicates the value of p2 at which adsorption becomes appreciable and the quantity adsorbed. The type of adsorption site is more difficult to deduce but information on this can be obtained from the variation of rz with 8, the angular deviation of the surface orientation. This is obtained from the thermodynamic equationlg Data on t and ys as functions of p2 have been obtained by the following methods. 1) Twin Boundary Grooving—By determining the effect of adsorption on the torque, 7, where T is the variation of surface energy, y,, with orientation, it is possible to obtain some indication as to the preferred sites of adsorption. Experimentally, the torque value measured is the relative torque, 7/ys The twin boundary grooving technique suggested by Mykura'' was used in this study to determine near the three low-index orientations— (loo), (110), and (111). Mykura's equation relates 7 /yS to measurements of the di-

Jan 1, 1967

By M. Prats

The effect of a sand-filled vertical fracture of limited radial extent and finite capacity (fracture capacity is the product of the permeability and width of the fracture) on the flow behavior of a cylindrical reservoir producing an incompressible fluid through a centrally located well has been investigated mathematically. The shape of the lines of equal pressure near the fracture is essentially independent of the size of the reservoir, provided that the field radius is of the order of the fracture length or larger. For reasonable values of production rates and of fluid, reservoir and fracture properties, the total pressure drop between the end of the fracture and the well is gelrerally negligible compared with the pressure drop in the reservoir. With regard to production response, the effect of vertical fractures can be represented by the production response of an equivalent or effective well radius. For a high-capacity fracture, the effective well radius is a quarter of the total fracture length, decreasing with the fracture capacity. When invasion effects are simulated by decreasing the width of the damaged zone with distance from the well, the effect of formation damage around a fracture on the production response is not so seriolls as indicated by the literature. This suggests that frac fluids with a conventional filter-loss response are better than high-spurt-loss frac fluids, provided the effective permeability of the damaged zone is the same. INTRODUCTION This paper considers the effect of the fracture capacity, as well as the formation damage which can result from fracture treatments, on the productive capacity of vertically fractured wells. Other publications, notably those of van Poollen,l,2 consider these same effects. In addition to providing more general results for vertical fractures than are available from the liter- ature, the present paper gives the equivalent well radius of fractures having different lengths and capacities and, also, includes pressure distributions in and around the fractures. The effect of a damaged zone around a fracture on the production response was not found to be so great as that reported by van Poollen. 2 This difference probably stems from the fact that we consider a damaged zone which is widest (but is still small) near the well and thins out toward the extremities of the fracture, whereas van Poollen considers a damaged zone having a uniform width for the entire fracture length. Simple, but adequate, equations which describe the effect of these variables on production response are presented (in Appendixes A and B). Thus, results can easily be extended to values of the variables not specifically considered here. IDEALIZATION AND DESCRIPTION OF THE FRACTURED SYSTEM It is assumed that a horizontal oil-producing layer of constant thickness and of uniform porosity and permeability is bounded above and below by impermeable strata. The liquid is incompressible. It is assumed that, after the well is fractured, the cylindrical outer "boundary" is at a uniform potential, provided that it is not too near the fracture. The fracture system is represented by a single, plane, vertical fracture of limited radial extent, bounded by the impermeable matrix above and below the producing layer (reservoir).3 Fig. 1 indicates the general three-dimensional geometry of the fractured reservoir described above. If gravity effects are neglected, the flaw behavior in the reservoir will be independent of the vertical position ill the oil sand. This means that the flow behavior in the fractured reservoir can be described by the two-dimensional flow behavior shown in the horizontal cross section of the reservoir, Fig. 2. PARAMETERS The effect of a fracture on the pressure distribution in the fracture itself and in an otherwise undamaged (no skin) reservoir indicates that the pressure distribution is a function of three parameters.

By G. V. Smith, R. F. Mehl

The decomposition of austenite in steels, because of its immerse practical importance, has been subjected to extensive study in recent years from the point of view of the mechanism of the process.1"3 Although much information has been acquired, a number of questions, principally of theoretical interest, remain. One is that of the atomic-crystallographic mechanism by which each of the various reaction products forms. The isothermal reaction products of the eutectoid decomposition in plain carbon steels (to which this study is restricted) have conveniently been classified in three general groupings—pearlite, bainite, and martensite. Of these several products, pearlite and martensite have been studied extensively, but bainite has received only scant attention. -As a result, the mechanism of the formation of pearlite and that of martensite are now fairly well understood while a great deal of uncertainty exists regarding bainite. Pearlite Pearlite forms from austenite by the precipitation of alternate platelets of cementite and ferrite, which grow into the austenite matrix.2--5 The rate of reaction may be described in terms of a rate of nucleation and a rate of growth.2.3 Mehl and Smith6 have attempted to determine the lattice relationships existing between the ferrite in pearlite and the' parent austenite. Using a pole-figure method of analysis, it was found that a limited number of ferrite orientations resulted from the decomposition of a single grain of austenite; it was not possible, however, to decide between two assumed ideal relationships, both of which appeared to account for the experimentally determined pole figure. It was definitely shown, however, that the relationship obtaining was quite different from that determined for the proeutectoid separation of ferrite.7 No attempt was made to determine the habit plane (matrix plane to which the precipitate lies parallel) of the pearlite lamellae. Belaiew8 earlier had stated that the number of directions assumed by the pearlite lamellae in a single grain of austenite was 12 (no details were given) and concluded wrong!:!, as Mehl and Smith6 have pointed out, that the lamellae delineate the {2I0} planes of ferrite.* Martensite It is known that martensite is a transiti0nal constituent of body-centered tetragonal lattice,' and that it forms suddenly

Jan 1, 1942

By R. F. Mehl, G. V. Smith

The decomposition of austenite in steels, because of its immerse practical importance, has been subjected to extensive study in recent years from the point of view of the mechanism of the process.1"3 Although much information has been acquired, a number of questions, principally of theoretical interest, remain. One is that of the atomic-crystallographic mechanism by which each of the various reaction products forms. The isothermal reaction products of the eutectoid decomposition in plain carbon steels (to which this study is restricted) have conveniently been classified in three general groupings—pearlite, bainite, and martensite. Of these several products, pearlite and martensite have been studied extensively, but bainite has received only scant attention. -As a result, the mechanism of the formation of pearlite and that of martensite are now fairly well understood while a great deal of uncertainty exists regarding bainite. Pearlite Pearlite forms from austenite by the precipitation of alternate platelets of cementite and ferrite, which grow into the austenite matrix.2--5 The rate of reaction may be described in terms of a rate of nucleation and a rate of growth.2.3 Mehl and Smith6 have attempted to determine the lattice relationships existing between the ferrite in pearlite and the' parent austenite. Using a pole-figure method of analysis, it was found that a limited number of ferrite orientations resulted from the decomposition of a single grain of austenite; it was not possible, however, to decide between two assumed ideal relationships, both of which appeared to account for the experimentally determined pole figure. It was definitely shown, however, that the relationship obtaining was quite different from that determined for the proeutectoid separation of ferrite.7 No attempt was made to determine the habit plane (matrix plane to which the precipitate lies parallel) of the pearlite lamellae. Belaiew8 earlier had stated that the number of directions assumed by the pearlite lamellae in a single grain of austenite was 12 (no details were given) and concluded wrong!:!, as Mehl and Smith6 have pointed out, that the lamellae delineate the {2I0} planes of ferrite.* Martensite It is known that martensite is a transiti0nal constituent of body-centered tetragonal lattice,' and that it forms suddenly

Jan 1, 1942

By Charles R. Fettke

In the present day manufacture of glass nearly pure quartz sands are used almost exclusively as the source of the silica, which is the major constituent of all common varieties of glass. Ordinary soda-lime, such as bottle, common tableware, plate, and window glasses, contains from 65 to 75 per cent. of silica. Occurrence Glass sands occur in nature either in the form of loose, unconsolidated sediments or in deposits in which the individual grains have been more or less thoroughly bound together by some cementing agent so as to form sandstones. While deposits of sand and sandstones occur both widely and abundantly distributed, deposits that are sufficiently free from other constituents than quartz grains, so that they can be employed in the manufacture of the better grades of glass, are, comparatively speaking, of rare occurrence. The major portion of the glass sand produced in the United States comes from sandstones. In order to be suitable for glass sand, they should be rather friable. The rock should break down readily along the cementing material between the grains and should not break across the grains rather than along the bond. Some of the sandstones used are so friable that only light shots of slow-burning dynamite are necessary to disintegrate them sufficiently for hydraulic mining, while others have to be passed through crushers in order to disintegrate the rock into its individual grains. MINERALOGICAL COMPOSITION An ideal glass sand is made up entirely of grains of the mineral quartz free from inclusions of foreign substances. Sands containing 100 per cent. silica, however, are not found in nature, although some very nearly approach this composition.

Jan 1, 1926

By A. A. Collins

OF widespread interest to all lead metal¬lurgists is a dross smelting process that will consistently give mattes and speiss of low lead and high copper contents. It is -a problem that has intrigued operators through the years. In the past few years, with increased amounts of copper and overcrowded metallurgical furnaces, it has been almost imperative to evolve some method. Experience at El Paso has shown that high copper-to-lead ratios can be consistently attained by use of the new soda process.* OLDER METHODS Three older methods; i.e., I. Dross plus siliceous ore and limestone, 2. Dross plus one fourth blast-furnace speiss and siliceous ore, 3. Dross plus sulphides and siliceous ore and scrap iron, do not give consistent results and the products are higher in lead and lower in copper than those produced with the soda process. Any radical changes in the blast-furnace drosses will throw any of these older methods into a tailspin. For almost ten years, El Paso used the third method, with varying results. It was noted that as the arsenic and antimony contents of the dross increased, the speiss and matte steadily increased in lead and decreased in copper. A dross containing four parts of copper to one part of arsenic was considered to be ideal. At times this balance of copper to arsenic was almost impossible to obtain, especially when handling copper Cottrell dusts, which vary so greatly in copper and arsenic. Custom smelters like El Paso, handling a great variety of dusts, concentrates and ores, are apt to have anywhere from 1 to 15 pct copper on charge, with a variable in arsenic of from 0.5 to 2 pct. With such conditions, and drosses varying from 12 to 40 pct copper, an operator using the older dross reverberatory practices would find it just about im¬possible to control the reverberatory operations and to produce a good product low in lead and high in copper. These conditions prevailed at El Paso from the year 1940 to the present. In May 1942 it, was decided to experiment with the soda process. THE SODA PROCESS After considerable work the soda method was finally evolved to the present state. It has never failed to produce a good product even under the most adverse conditions. It might be well to remember that many men of thought in the smelting industry have at one time or other suggested the removal of all copper, arsenic and antimony from the lead blast-furnace charge as an aid to better metallurgy.

Jan 1, 1947

By John Wulff

In a previous paper Burwell and Wulff1 have shown by electron diffraction studies that allotropic transformations can be induced in 18-8 stainless steel by polishing to a depth of about 5 X 10-5 cm. The development of a successful etching technique, which removes accountable amounts of metal from the surface without pitting and without changing the root-mean-square profile as measured with an Abbot pro-filometer, led to the application of the whole technique and material to an investigation of various mechanical methods of surface preparation, such as grinding, lapping, superfinishing and cold-rolling. Ideally suited to such a study is 18-8 of low carbon and nitrogen content. The material can be heat-treated to produce a coarse-grained single-phase structure. On cold deformation there occurs not only a reduction in grain size but, at regions of maximum stress, a change of face-centered material to body-centered material, provided the metal is worked below about 200°C. When worked between 200"about and 415°C., diffraction studies evidence a reduction in grain size without the appearance of any new body-centered ferrite. Ferrite, which can be referred also to strains induced by carbide precipitation, is evident when the material is worked at temperatures between 4150 and 800°C. Stainless steel is advantageous because the usual surface-finishing operations do not readily oxidize it to any appreciable depth. In order to produce detectable oxide films on the surface of austenitic 18-8 in a time equivalent to that required to produce, for example, a fine ground finish on 1/2 sq. in., the sample must be held in a furnace or oxygen stream above 600°C. By using longer heating times, it is possible to achieve measurable oxide films on samples , whose surface temperatures exceed only about 250°C. Experimental Procedure The apparatus, material, and technique described in the previous paper1 were employed in this investigation. Samples of 18-8, I by I cm. by 4 mm., were carefully annealed in the austenitic range to produce a coarse-grained structure. They were then quenched and pickled to remove scale, On a lapping machine of the Graton2 type, both sides of each sample were polished to a a of 1/6 a wave length of sodium D light. Thereafter they were electrolytically etched to remove at least 1 X 10-3 cm. of the surface, a depth that is well below that of any defermations induced by surface preparation. samples of this material, carefully mounted in steel holders, were then sent to various industrial organizations known for special finishing techniques. In the instrue ment shops at the Massachusetts Institute of Technology check samples were finished by the same methods, as far as they were available. Abbot profilometer3 readings Were made on all the samples, which were then carefully degreased in double distilled benzine and alcohol, dried in a hot-filtered air blast, and kept in a desiccator. SUC-

Jan 1, 1941

By P. H. Cardwell

The effect of various plastics upon the permeability of a sand and the mechanism of their ensuring permeability within the consolidated sand body is discussed. Data are presented on various properties of the plastic materials used in sand consolidation and the effect of temperature and usable temperature ranges are considered. The recovery of petroleum from uncon-solidated sands presents serious production problems, owing to sloughing of the formation. The solution of some of these problems usually has been by mechanical methods.' The ideal way of controlling the sloughing tendencies of these un consolidated formations, however, is to prevent the movement of the individual sand grains by the use of a bonding medium. A step in the desired direction was taken by Irons and Stcesser2 when they taught the use of liquid plastics to produce a consolidating deposit that prevents sloughing. More recently, Wrightsman and Buckley3 proposed a modification of this process. In this use of the liquid plastic, the sand grains become coated and the ensuing hardening of the plastic by polymerization or condensation cements together the sand Particles. Liquid plastics that have been suggested for this Purpose are of the following types: phenolformaldehyde, alkyd resins, vinyl type resins, polystyrene and the acrylic esters. When the flow of fluids through a sand must not be materially reduced, it is essential only to cement together the sand grains with liquid plastic and leave a portion of the interstitial space for fluid flow. TO be assured of obtaining fluid flow through the sand interstices after injection of plastic, it has been necessary in the past to remove the excess plastic from the interstices between the particles before it sets. Wrightsman and Buckley suggest two methods for the removal of the excess plastic from the interstices of the sand: (I) to flush the excess plastic back into the formation, away from the well bore, by use of oil or water; (2) to produce the well before the plastic has set, thereby moving the excess plastic into the well bore. Under certain well conditions it is very difficult to remove the excess plastic from all parts of the formation by either of these methods and leave the formation consolidated with no sections completely sealed. The method* described herein of retaining permeability within a sand body is to use a liquid plastic that upon setting ensures permeability within the consolidated sand body. This cements the sand grains but obviates the need for removing plastic from the interstices of the sand. One of the ways of accomplishing this is to use a liquid plastic that occupies a considerably greater volume than the solidified resin it yields on further polymerization or condensation in situ. In order to be satisfactory, the volume of the plastic while liquid should be at least one and one half times the volume of the solid formed. Preferably,

Jan 1, 1947

By Harry H. Angst

THE history and efficiency of 40-ton capacity dump trucks for surface waste removal at the New Cornelia opencut copper mine, at Ajo, Ariz., are summed up in this paper. Tabulations of truck performance, together with detailed cost figures, prove the value of truck transportation for certain special operations at a large mine. Emphasis is given to the fact that truck transportation not only reduces the haulage costs but also reduces the breaking ground and shovel-loading costs per ton. The New Cornelia opencut copper mine is in the desert. The climate is ideal for seven months of the year, but the five summer months are uncomfortably hot. The elevation is 1820 ft. above sea level and the annual rainfall is approximately 6 inches. The ore body is a monzonite-porphyry deposit. The waste-rock capping consists of hard rhyolite, conglomerate and porphyry. All the material is hard and cannot be excavated without blasting. The rhyolite and conglomerate waste is very blocky. The weight of the rock in place is 2.16 tons per cubic yard. The average mine production per day is 22,000 tons of ore and 18,000 tons of waste rock, the latter consisting of surface rock and material within the ore body too low in grade to send to the concentrator. The rock is loaded by electric shovels with 4 ½ -cu. yd. dippers. The primary transportation of ore to the concentrator and waste to the dumps is by 30-yd. dump cars and oil-burning steam locomotives; therefore truck haulage of waste is a minor factor of the New Cornelia operation. However, as New Cornelia was one of the first mines to use large-capacity dump trucks for haulage, the results obtained are of interest. EQUIPMENT On the south side of the New Cornelia is a hill rising about 500 ft. above the normal surface elevation, roughly 1000 ft. in diameter at its base, called locally Arkansas Mountain peak. Exploratory drilling in this area developed additional ore that could be made accessible for open pit operation only by moving the mountain face a maximum distance of 400 ft. to the south. The slope of the mountain adjacent to the pit averaged 35°, and the small area involved precluded the use of train haulage for the removal of the 4,000,000 tons of waste estimated above the normal pit elevation. A study of dump-truck haulage at Boulder Dam and San Gabriel Dam led to the decision to use large-capacity end-dump trucks rather than smaller trucks, for the following reasons: 1. The truck would have to withstand the impact of hard, heavy chunks, some of them weighing as much as 10 tons, which would be dumped from the 4 ½ -cu. yd. dipper. 2. The coarse, rocky, abrasive material would soon damage a light truck body. 3. The body of a small truck could not be efficiently loaded with coarse rock.

Jan 1, 1941

By John Wulff

In a previous paper Burwell and Wulff1 have shown by electron diffraction studies that allotropic transformations can be induced in 18-8 stainless steel by polishing to a depth of about 5 X 10-5 cm. The development of a successful etching technique, which removes accountable amounts of metal from the surface without pitting and without changing the root-mean-square profile as measured with an Abbot pro-filometer, led to the application of the whole technique and material to an investigation of various mechanical methods of surface preparation, such as grinding, lapping, superfinishing and cold-rolling. Ideally suited to such a study is 18-8 of low carbon and nitrogen content. The material can be heat-treated to produce a coarse-grained single-phase structure. On cold deformation there occurs not only a reduction in grain size but, at regions of maximum stress, a change of face-centered material to body-centered material, provided the metal is worked below about 200°C. When worked between 200"about and 415°C., diffraction studies evidence a reduction in grain size without the appearance of any new body-centered ferrite. Ferrite, which can be referred also to strains induced by carbide precipitation, is evident when the material is worked at temperatures between 4150 and 800°C. Stainless steel is advantageous because the usual surface-finishing operations do not readily oxidize it to any appreciable depth. In order to produce detectable oxide films on the surface of austenitic 18-8 in a time equivalent to that required to produce, for example, a fine ground finish on 1/2 sq. in., the sample must be held in a furnace or oxygen stream above 600°C. By using longer heating times, it is possible to achieve measurable oxide films on samples , whose surface temperatures exceed only about 250°C. Experimental Procedure The apparatus, material, and technique described in the previous paper1 were employed in this investigation. Samples of 18-8, I by I cm. by 4 mm., were carefully annealed in the austenitic range to produce a coarse-grained structure. They were then quenched and pickled to remove scale, On a lapping machine of the Graton2 type, both sides of each sample were polished to a a of 1/6 a wave length of sodium D light. Thereafter they were electrolytically etched to remove at least 1 X 10-3 cm. of the surface, a depth that is well below that of any defermations induced by surface preparation. samples of this material, carefully mounted in steel holders, were then sent to various industrial organizations known for special finishing techniques. In the instrue ment shops at the Massachusetts Institute of Technology check samples were finished by the same methods, as far as they were available. Abbot profilometer3 readings Were made on all the samples, which were then carefully degreased in double distilled benzine and alcohol, dried in a hot-filtered air blast, and kept in a desiccator. SUC-

Jan 1, 1941

By P. H. Cardwell

The effect of various plastics upon the permeability of a sand and the mechanism of their ensuring permeability within the consolidated sand body is discussed. Data are presented on various properties of the plastic materials used in sand consolidation and the effect of temperature and usable temperature ranges are considered. The recovery of petroleum from uncon-solidated sands presents serious production problems, owing to sloughing of the formation. The solution of some of these problems usually has been by mechanical methods.' The ideal way of controlling the sloughing tendencies of these un consolidated formations, however, is to prevent the movement of the individual sand grains by the use of a bonding medium. A step in the desired direction was taken by Irons and Stcesser2 when they taught the use of liquid plastics to produce a consolidating deposit that prevents sloughing. More recently, Wrightsman and Buckley3 proposed a modification of this process. In this use of the liquid plastic, the sand grains become coated and the ensuing hardening of the plastic by polymerization or condensation cements together the sand Particles. Liquid plastics that have been suggested for this Purpose are of the following types: phenolformaldehyde, alkyd resins, vinyl type resins, polystyrene and the acrylic esters. When the flow of fluids through a sand must not be materially reduced, it is essential only to cement together the sand grains with liquid plastic and leave a portion of the interstitial space for fluid flow. TO be assured of obtaining fluid flow through the sand interstices after injection of plastic, it has been necessary in the past to remove the excess plastic from the interstices between the particles before it sets. Wrightsman and Buckley suggest two methods for the removal of the excess plastic from the interstices of the sand: (I) to flush the excess plastic back into the formation, away from the well bore, by use of oil or water; (2) to produce the well before the plastic has set, thereby moving the excess plastic into the well bore. Under certain well conditions it is very difficult to remove the excess plastic from all parts of the formation by either of these methods and leave the formation consolidated with no sections completely sealed. The method* described herein of retaining permeability within a sand body is to use a liquid plastic that upon setting ensures permeability within the consolidated sand body. This cements the sand grains but obviates the need for removing plastic from the interstices of the sand. One of the ways of accomplishing this is to use a liquid plastic that occupies a considerably greater volume than the solidified resin it yields on further polymerization or condensation in situ. In order to be satisfactory, the volume of the plastic while liquid should be at least one and one half times the volume of the solid formed. Preferably,

Jan 1, 1947