Search Documents

By R. B. Alke

Request to Mine Beneath Bridge The Jabs Run Bridge is a reinforced portland concrete arch filled bridge located on WV Bouts 7 near Pentress, WV. The bridge has a span of 22.9 m (meters) and a height of 4 m above normal pool elevation to the underside of the center of the arch (See Pig 1). The bridge is a two lane structure with a width of 6.86 m. The structure is over 50 years old Wing been built in 1929 and is owned by the Department (WV Department of Highways).

Jan 1, 1984

By Vern Miller

The Bureau of Mines developed a detector for controlling sorting devices to separate the copper-bearing fragments from the barren portion of Michigan native copper and western porphyry copper ores. A successful sorter could be used to preconcentrate the ore and eliminate costly hoisting or hauling of waste. An induction balance unit was developed and used in sorting tests on crushed sized -1+1/2-inch (-2.5+1.3-cm) ores from the Kingston (0.9 pct CU) and Centennial (1.6 pct Cu) mines of Upper Michigan. Concentrates of 4.0 pct and 7.5 pct Cu, respectively, were obtained at recoveries of 85 and 80 pct of the copper in the feed. Eighty percent of the sorted ore was rejected as tailing. Sorting larger fragments improved the separation efficiency. Tests on -4+2-inch (-10+5-cm) sized Kingston (1.6 pct Cu) and Centennial (2.1 pct Cu) ore samples yielded concentrates of 4.3 and 4.5 pct Cu, respectively, with corresponding recoveries of 92 and 91 pct. About 60 pct of the sorted ore was discarded as tailing. Porphyry copper sulfide ores also responded to electronic sorting but at a lower separation efficiency. Sorting response was affected by the degree of segregation.

Jan 1, 1976

By T. A. Sullivan

The processing of sweated aluminum electronic scrap was investigated to develop methods for recovering the aluminum and concentrating the other metals, including copper, lead, gold, and silver, into a product that can be separated by known methods. Two molten-salt electrorefining processes were developed and tested. The first process utilized a three-layer refining cell with a BaCI2-NaF-AIF3 electrolyte, which operated at 750° to 850° C. The second process used an all-chloride electrolyte of NaCI-KCI-AICI3 at 750° to 800° C, with separate anode and cathode compartments. High-quality aluminum was recovered that averaged 99.8-percent pure in the three-layer cell and 99.6-percent pure in the compartment cell. Over 94 percent of the aluminum was recovered with cathode current efficiencies of approximately 90 percent in both methods. The copper, lead, tin, silver, gold, and other metals were concentrated threefold in an anode product. Separation of lead and part of the tin by liquation from this product seemed feasible. The anode product was smelted to prepare a 96-percent copper bullion that contained 690 ounces of silver and 65 ounces of gold per ton, with 98 percent recovery of these values.

Jan 1, 1972

By Michael Gobla

"Since 1994 the Bureau of Reclamation (BOR) has used risk analysis to evaluate dams. Risk considers both the likelihood of failure and the expected consequences should failure occur. Risk analysis relies on the detailed formulation and critical analysis of all possible potential failure modes. Potential failure modes are formulated by describing the sequence of events that must occur to result in failure, where failure is defined as the uncontrolled release of the impounded reservoir. Failure occurs in response to loadings such as water seepage through a dam (static forces), shaking from an earthquake (dynamic forces), sudden flood inflows (hydrologic forces), or accidental overfilling (operational errors). Reclamation has, to a limited extent, applied risk analysis to inactive and abandoned mines to evaluate tailings dams, pit lakes and flooded underground mines. Case histories of potential failure mode analysis, as applied to mine impounded water, illustrate what critical technical information is needed to determine if failure is likely, what the consequences of failure are likely to be, and what are the highest risks that should be addressed first.IntroductionImpounded water and high water content wastes at mining and industrial processing sites are potential threats to public safety and the environment. Recent failures such as the TVA Kingston flyash impoundment failure in Tennessee in 2008 (4.1 million m3 or 5.4 million cu yd) release, the Mt. Poly Tailings Dam failure in British Columbia in 2014 (4.4 million m3 or 5.8 million cu yd) release, and the Samarco Fundao Tailings Dam failure in Brazil in 2015 (59 millon m3 or 78 million cu yd) release have renewed attention to this issue. Potential risks from impounded water at mining and industrial sites originate not only from tailing dams, but also from water in process ponds and conveyance pipelines, sediment retention dams, water retention dams, mine pit lakes and flooded underground mine workings.Conventional water retaining dams also have a record of failure. Notable examples of failure include Vajont Dam in Italy in 1963 (2,600 lives lost), Banqiao and Shimantan Dams in China in 1975 (171,000 lives lost), and Machhu-II Dam in India (10,000 lives lost). After the 1976 Teton Dam failure in Idaho, the U.S. Bureau of Reclamation (BOR) established a Dam Safety Program. By 1984, the agency developed and began using risk analysis methods. BOR operates and maintains an inventory of hundreds of aging dams which were designed and constructed over a period of 100 years. Many of these facilities were designed and constructed prior to the development and adaptation of modern soil mechanics in dam engineering. Diligent observational monitoring, detailed site investigations and the application of risk evaluation to the BOR dam inventory has identified many deficiencies resulting in significant demands on available funding for remediation efforts. The application of risk analysis has allowed the agency to rank sites by risk. By giving priority of remedial efforts to high-risk sites, significant improvements to dam safety have been achieved."

Dec 1, 2016

By K. L. Paciorek

The aim of the present study was to determine the thermal oxidative behavior of materials used in coal mines, with emphasis on the type and relative concentration of the products, in particular the toxic species formed. To supplement this work and to gain understanding as to the type of products possibly formed and also to assess the limitations and advantages of the various analytical methods used a literature survey of the past investigations performed on the compositions of direct interest to the subject program was conducted. The compositions thus covered were cellulose, polyvinyl chloride, neoprene, urethanes, polyamides, polyesters, polyethylene, epoxy, phenoxy, urea-formaldehyde and melamine formaldehyde resins. The results of this review are compiled in the Appendix. The experimental work consisted of thermal oxidative degradation of 36 materials and 4 composites using a stagnation burner apparatus developed in these laboratories which affords a dynamic system approximating somewhat the conditions encountered in underground coal mines. This technique as employed during this program gave only the relative product concentration at specific periods of the decomposition process, The advantage of this approach is that in this manner screening of materials can be accomplished in conjunction with some assessment of the decomposition rate as influenced by temperature and material composition. Limited static tests were performed using a sealed tube method. The materials studied were grouped according to their compositions. The following were the main groups: (a) polyvinyl chloride-containing materials, (b) neoprene compositions, (c) rigid foams (urethanes, isocyanates), (d) miscellaneous materials (including jute, fiberglass, polyethylene and some articles of unknown composition), (e) coal and fluids (phosphate esters, organic esters, oil-water emulsions), and finally (J) composites. The latter comprised a mixture of a phosphate ester fluid with (a) coal, (b) a representative polyvinyl chloride sample, and (c) a neoprene type composition.

Jan 1, 1972

By A. L. Mular, R. P. Edwards

"The operation of flotation circuits is often regarded as a combination of art and science. Expert systems offer a method by which the art may be captured and supervisory control of flotation circuits fully realized. Operating knowledge, the art, can be consistently employed to enhance regulatory control through the judicious application of an expert system. Using an expert system, a supervisory control routine was developed, and successfully implemented, in the copper flotation circuit at Brenda Mines Ltd.The expert system ran in conjunction with regulatory PI controllers on a personal computer. The expert system received assays via an on-stream analyzer and adjusted regulatory loop setpoints as required in real-time. From its commissioning in November 1989, to the end of the mine's operation in June, 1990, the ES was enthusiastically embraced by the operators and attained operating levels superior to those achievable manually.INTRODUCTIONExpert system (ES) software springs from research into artificial intelligence and is currently making significant inroads into business and industry. Proponents of ES's make many attractive claims; they are a means of capturing the knowledge of experts and they can be programmed by non-programmers. To date, most uses of this software in the process industry are in off-line applications, meaning that the applications are not tied directly to operating (on-line) environments. Moreover, in on-line environments, they are typically employed as advisors and only suggest changes. Human operators are required to close-the-loop to the process. Yet, ES's should be applicable to operating environments and, if the claims of the proponents are valid, should also be better than existing tools. As an intelligent controller an ES must use the knowledge of experienced operators, apply it directly to a process and do this without the intervention of human operators. On-line applications have been successfully employed in the closed loop control of SAG circuits (Herbst et al., 1989) and flotation circuits (Hales, 1989). Harris and Kosick (1988) detail an implementation for flotation control at the Polaris Mine."

Jan 1, 1991

By B. W. Stunkard

Hibbing Taconite Company is located by the cities of Hibbing and chisholm near the center of the Mesabi Range, approximately 169 km (105 miles) from the Canadian Border. The plant site is equidistant from these two communities, about 6.4 km (4 miles) from each. A 169 km (105 mile) railroad connects us with the port of Superior, Wisconsin, where the pellet production is loaded into lake carriers for lower lakes destinations. Immediately to the south of the mine area is the world famous Hull- Rust-Mahoning Mine which produced more than 700 000 000 million tons of red ore between the years 1893 and 1973.

Jan 1, 1979

By Jorge Cárdenas, Alejandro Luna

In mining simulation for fragmentation results prediction is of utmost importance to study feasibility, ensure safety, and estimate the correct use of resources in drilling an explosive to meet requirements and avoid excessive usage. One critical case is fragmentation prediction, developed through models. Developing a fragmentation model in a mining unit aims to control blasting results to align theoretical and real data and improve correlation. Therefore, it is essential to collect post-blast fragmentation data, organize it, and systematically process it to develop a suitable model that meets variable requirements. Using a robust system of equations, this model should generate the required results with minimal variability between simulation and actual results. Additionally, this model must be adaptive to reduce this variability. Studying the most known and used models in mining resulted in our work correlating Cunningham 2006, Swebrec, and CZM models. Thus, the Simfrag model was created, presenting a robust foundation and combining the most notable advantages of the aforementioned models.

Jan 21, 2025

By D. A. Buckingham

Engineering and economic evaluations were performed by the Bureau of Mines on 14 Frasch sulfur, 1 native sulfur, and 21 metal sulfide operations in 11 market economy countries. The evaluation included discounted-cash-flow rate-of-return economic analyses at 15 pct to determine the average total cost of production of these two commodities and the potential availability of elemental sulfur (8) and pyrite concentrate. The Bureau evaluated the potential availability of elemental sulfur and pyrite concentrate. Approximately 279 million metric tons (Mmt) of pyrite concentrate at 46 pct 8 is potentially recoverable from 422 Mmt of in situ metal sulfide ore. Nearly 89 pct of the total pyrite concentrate is available at an average total cost of production below the January 1984 pyrite concentrate market price ($43/mt). About 185 Mmt 8 is potentially recoverable from 253 Mmt of in situ elemental sulfur. About 99 pct of this sulfur is available at an average total cost of production below its January 1984 market price ($131/mt).

Jan 1, 1986

By Michael Day, Paul Kos, Scott Brinton

A hydrogeologic characterization and impact analysis was performed for a proposed quarry at the Hitch Rack Ranch located in the Little Turkey Creek watershed southwest of Colorado Springs, Colorado. Continuous multiple channel tubing, nested piezometers, stream flow measurements, and mapping of known seeps were used to define the three-dimensional potentiometric distribution and areas of groundwater recharge and discharge. Water balance considerations, mass balance calculations, and potentiometric response to earth tides and barometric fluctuations confirmed that the granite fracture system in the ridge area of the proposed quarry has an extremely low bulk hydraulic conductivity resulting in minimal groundwater discharge to sustain the baseflow of Little Turkey Creek. The Little Turkey Creek valley forms the major conduit for groundwater flow exiting from the upper part of watershed underlain by granite. This conclusion has significant implications with respect to mine planning to minimize projected impacts to the hydrologic system and preserve this recharge component to downgradient Denver Basin sedimentary deposits.

By A. M. Richardson

The significance of a massive sandstone unit in the immediate roof to longwall support weighting is well known. If the unit lies in the main roof above the zone of caving, its influence becomes more difficult to calculate using traditional methods. Much of the reserves at Cyprus Plateau's new, multi-seam Willow Creek Mine are located in the A Seam. The massive Kenilworth Sandstone is typically situated 21.3 m (70 ft) above the A Seam in the main roof and is on average 14.6-m (48-ft) thick, ranging to 29.0-m (95-ft) thick. This paper describes the application of distinct-element modeling to determination of the appropriate yield capacity for supports at Willow Creek. The modeling was determined to be useful for understanding support loading mechanisms and as an aid to engineering judgment in selecting supports.

Jan 1, 1996

By L. Lariviere, M. Grenier, R. Khalili, D. Shook

A mineral processing facility near Montreal, CEZinc, Noranda Inc., has recently implemented a leading-edge intranet solution for monitoring the performance of plant operations, and providing condition-based maintenance. This innovative multi-faceted software implementation incorporates: web-delivered plant information systems; area-wide control loop performance assessment (using sophisticated algorithms to evaluate poorly performing controllers); and integrated alarm management functions.The system has enabled a project to improve plant operations through better process control. Maintenance technicians, engineers, supervisors and managers all can see the performance of the controllers, and the performance of the plant itself, through webdelivered graphics and reports. Information is combined from many sources, real-time, historical, relational and analytical, to provide a complete picture of plant operation.The web-based solution centralizes the administration of user access, and simplifies the deployment of several different kinds of information to many desktops. It is an extensible system that allows users to create and share their own web pages and data views.The paper will discuss the solution architecture and the improvements the IT, operations, maintenance, and engineering groups have experienced, and overall benefits to the facility.

Jan 1, 2003

By M. P. Hardy

Copper-Nickel ores in northeastern Minnesota could establish a new industry in a region where underground mining has not been active. This study reviews geotechnical data relevant to the selection and design of underground mines in this region and by numerical structural analysis evaluates the importance of some geotechnical parameters to mine method selection. Because of the rapid development of computer modeling many new techniques have become available for modeling rock mass behavior in recent years. An overview of these methods is presented and their applicability to mine design reviewed. Methods included in this summary were the differential continuum models, such as finite Pint and finite difference, integral continuum models, such as boundary element, displacement discontinuity and boundary integral equation methods, and discontinuum methods such as the distinct block model. The displacement discontinuity method was used to evaluate the influence of geotechnical parameters on some aspects of mine design. Three problems; room stability, pillar stability on a weak inclined contact and sill pillar thickness influence on sill pillar stability, were analyzed to evaluate the relative importance of insitu stress field and joint properties on design. It was concluded that for stability analysis the initial horizontal stress is of most importance in all aspects of design. The position, orientation, persistence and strength of joints is also of primary concern. In a more general sense, however, it was concluded that detailed geotechnical parameters have much less influence on mine method selection than more general factors such as rock quality, initial stress state, orebody shape and economics.

Jan 1, 1978

By Jacques F. Abrahamse, Kevin A. Bahe, T. Arthur Palm, Gregory E. McCluskey, Stephen L. Bessinger

Introduction Basis For System San Juan Coal Company (SJCC) is a subsidiary of BHP Billiton. Until recently, BHP Billiton operated three surface mines in northwestern New Mexico: Navajo, San Juan, and La Plata. The San Juan and La Plata Mines supplied the San Juan Generating Station operated by Public Service of New Mexico. Stripping ratios at those operations were increasing, and by 2000 a feasibility study was underway to develop SJCC’s vast underground reserves as a replacement. Early in the evaluation and planning phase for the San Juan Underground Mine, it was determined that the target seams (Fruitland #8 and #9) had a high propensity for spontaneous combustion. Spontaneous combustion was identified as a risk, both to personnel and equipment, and to the ability of SJCC to reliably fulfill its obligation to the power plant. In the last 20 years, several western US coal mines suffered underground spontaneous combustion events and/or mine fires. Included in this group were Colorado Westmoreland’s Orchard Valley Mine (1987), RAG’s Willow Creek Mine (1998 and 2000), Oxbow’s Sanborn Creek Mine (1999), the West Elk Mine of Arch Coal (2000), Arch’s Skyline Mine (2002), Western Fuels’ Deserado Mine (1996), and the West Ridge Mine of Andalex Resources (2003). The cause for the majority of these fires was spontaneous combustion. Fighting the fires required injection of an inert gas or foam. Nitrogen and carbon dioxide were the predominant choices of inert gas. In all cases, the gasses had to be trucked in from considerable distances. Before the inert gas could be used, injection holes had to be drilled into or near the suspected fire locations. This drilling and trucking caused costly delays in the timing of the fire fighting effort, and was not as precise as desirable. Emergency purchasing of gas and pumping services was extremely expensive, running as high as $70,000 per day at one mine. As a result of the experience of other western US coal operators, and the risk inherent with spontaneous combustion at SJCC, it was decided to pursue installation of a nitrogen delivery facility on-site at SJCC. This decision was later expanded to include a continuous supply of nitrogen.

Jan 1, 2005

By Jonathan S. Kelly

Effective control of respirable dust is one of the most serious problems associated with longwall mining in the United States. This report describes the development and the underground evaluation of ventilated cutting drums, on a double ended ranging drum shearer. The ventilated drum uses high pressure (1,500 psi) water sprays to draw air (3,500 cfm) through 12 airmoving tubes mounted in the drum hub. The sprays draw dusty air from the face side of the drum, scrub the air, and discharge the clean air on the gob side of the drum against a deflector plate. During a three week underground evaluation, the cutting drums reduced shearer generated dust levels at the shearer operators position by 40%, at the shield operators downwind of the shearer by 55%, and at the tailgate by 55%. Cutting and loading performance of the drums were superior to the mine?s conventional drums. After the evaluation, the mine continued to use the ventilated drums to finish mining the panel. During this 3 month period, there were no mechanical or seal failures demonstrating excellent system reliability.

Jan 1, 1987

By Andrew St. Amant

This report reviews the first three "investigative and concept generation" phases of the referenced contract, and details task performance of Phase IV. This last phase integrated the most promising concepts from Phases I, II, and III into a prototype detailed design which was manufactured, and then tested on a mine locomotive. The concepts developed during the first three phases provided "Improved Pole Tracking," automatic "Rapid Pole Retraction" in the event of dewirement, and servo-operated "Remote Pole Repositioning" on the trolley wire. The Appendix of this report supplies detailed information for the design and construction of the prototype system which is comprised of an RCB (Remotely Controlled Base subassembly), an RCL (Remote Control Lever subassembly) and an SAU (Servo Amplifier Unit) subassembly.

Jan 1, 1980

By M. Zuckerberg, E. Mader, R. Pasyar

We describe a new software product designed for the net present value optimization of multi-open-pit blended ore operations in which it is desired and/or necessary to dump some or all of the waste rock produced in the course of operations back into the voids created in the process of ore extraction. The software product simultaneously decides over the entire life-of-mine which material to mine in which year, once mined what to do with it, and where to put that material which it has decided to waste, all subject to annual blend and capacity constraints.

Jan 1, 2007

By Arthur D. FitzGerald

EDC established an Environmental Review Framework in 1999. Throughout the early fall of 2001, the Corporation held public consultations across Canada to strengthen that framework, leading to a public release on November 15, 2001 of a report summarising the results of these consultations. Following this, the Corporation implemented strengthened environmental review requirements in the form of its Environmental Review Directive, in compliance with legislated amendments to Canada?s Export Development Act that went into effect on December 21, 2001. Over the past few years, there has been a global trend towards an increase in the social and environmental requirements of multilateral/bilateral financial institutions and export credit agencies. More recently, this activity has focussed on capturing institutions that have not yet adopted similar requirements and, more specifically, on developing a convergence of the requirements from institution to institution. This paper describes EDC?s new ERD and some of the initiatives that have taken place or are in process that are moving international financial institutions toward converging their environmental and social requirements for projects in the private sector.

May 1, 2002

By J. A. Ruppert

The Bureau of Mines investigated methods of refining iron-contaminated zinc to marketable quality and developed a laboratory-scale process in which aluminum, added as a refining agent, reacted with the iron, forming solid Fe2Al which floated to the surface of the melt. Solids were separated by both filtration and centrifugation, using a unique type of "dipping" centrifuge devised during the work. Typical zinc recovery was 95 percent, and iron content of the metal was lowered from 0.37 to 0.02 percent.

Jan 1, 1967

By G. L. Oldwright, Virgil Miller

"The data presented in this paper were collected at the smelter of the Consolidated Mining & Smelting Co. of Canada Limited, Trail (Tadanac), Brithish Columbia. The authors are greatly indicated to S.G. Blayrock, vice president and general manager; James Buchman, smelter superintendent; and the staff members mentioned in Report of Investigation 3243. The authors are exceedingly grateful to George Murray, assistant smelter superintendent, for his keen interest, suggestions, and help in carrying out this investigation.INTRODUCTIONThe methods of charign the blast furnaces at Toole and Kelloggs were noted in Report of Investigations 2957 and 3094 respectively. Report of Investigations 2957 cited (4 to 9 inclusive) Hofman's Metallurgy of Lead (p. 226) and the work of A.S. Dwight, Thompson and Sicka, the staff of the Engineering and Mining Journal, and L.D. Anderson, N.F. Collins, in The Metallurgy of Lead (Chas. Griffin, London, 1910) also gives (pp. 247 254) the principles that he believes govern the successful charging of the blast furnace."

Dec 1, 1934