Search Documents

"ALTHOUGH Canadian metallurgists have long been active in research, the scope of the work was somewhat limited until the be-ginning -of World War II. The rapid industrial development of Canada during the past ten years has been accompanied by .a similar upsurge in research. However, the wide geographical distribution of the research centres has made it difficult for the individual research workers to meet together and to exchange ideas or even to learn what projects .are being investigated or the nature and extent of the facilities available for work of this kind.The purpose of the present symposium is to assemble data relating to projects under investigation and the facilities employed at the various metallurgical research laboratories in Canada, thus providing some measure of correlation so that workers in different locations may learn what kind of work •is being .done at other points throughout the country.In reporting the symposium it has not been possible to reproduce the papers in full, but excerpts have been selected that give the essentia1 data."

Jan 1, 1952

By A Liu, T Ren

Gas explosion in underground coal workings can pose a serious threat to the safety of mine workers and the entire mine operations. Gas explosion is a very complex thermal-chain reaction in a confined underground environment. Based on combustion and explosion theory, three dimensional (3D) computational models were developed to simulate mine gas explosion flame and overpressure wave propagation in a single entry gateroad in underground coalmines. Six different explosion scenarios were modelled and compared with large scale experimental results and AutoReaGas simulations. Model validations show that the use of shear-stress transport (SST) k-? model together with eddy-dissipation model (EDM) produces good agreement with both experimental and AutoReagas simulation results. Modelling results demonstrated that the changes of temperature versus time can be divided into four stages, ie the initial condition stage, and periods of warm-up, active burning, and burnt-out. Assuming a limited volume of methane is involved in the explosion, the maximum temperature decreases as the distance increases from the explosion point, with the highest temperature reaching about 2460 K. Modelling results show that the evolution of the explosion flame shape experiences four typical stages, ie spherical flame, finger-shape flame, flame with the skirt touching the side walls (ribs) and tulip flame, which are similar to the pattern of a duct explosion. The pressure in the gateroad remains the same as the initial value before the arrival of the explosion wave and then increases rapidly to the maximum value. Modelling results from this study will be used for the design of explosion arresting devices and mine seals in underground coalmines.CITATION:Liu, A and Ren, T, 2017. Computational simulation of gas explosion and its propagation in single entry gateroad, in Proceedings Australian Mine Vent Conference 2017, pp 181–188 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

By H. Doostmohammadi

During the tapping of liquid steel from Electric Arc Furnace (EAF), some slag is carried over into the ladle. High levels of FeO and MnO in slag carryover increase the oxygen activity in steel melt leading to oxide inclusion formation during the ladle treatment. The demand on cleaner steels requires minimization of carryover slag. In this work, the effect of EAF slag carryover on ladle slag-steel equilibrium calculations for a hot working tool steel was studied. Steel and slag sampling were done in Uddeholm Tooling AB in Sweden. XRF and OES techniques were used to determine chemical composition of samples. The quantity of slag carryover was calculated based on a mass balance followed by thermodynamic calculations on metal-slag equilibrium using Thermo-Calc software. The agreement between predictions and experimentally determined compositions was good. This leads to the development of a prediction method for optimizing the production of other tool steel grades.

Jan 1, 2009

By S. Y. Tan

As continual complementary metal?oxide?semiconductor (CMOS) scaling requirements, metal gate/high-k dielectric/Si gate stacks are expected to replace poly-Si/SiO2/Si gate stacks in the future CMOS sub-45 nm technology node. Hafnium based oxide is a promising candidate to replace SiO2 as a gate dielectric, due to its much higher dielectric constant (high-k) and stability. The key challenges of successfully adopting the high-k dielectric/Si gate stack into advanced CMOS technology mostly come from the interfacial properties. The origins of the electrical and physical characteristics of the dielectric oxide/bulk interface were studied in detail. The leakage current density-voltage (J-V) and capacitance-voltage (C-V) measurement techniques were employed to study the dielectric oxide/Si interface. The effects of the post-deposition annealing (PDA) treatment on the interface charges of dielectric oxides were studied. We found that the PDA can effectively reduce the trapping density and leakage current, and eliminate hysteresis in the C?V curves. Besides, the changes in chemical bonding features at HfO2/Si, HfSiO/Si and HfSiON/Si interfaces due to PDA treatment were evaluated by XPS measurements. The XPS analysis provides a better interpretation of the electrical outcomes. As a result, both HfSiO and HfSiON films have exhibited superior performance in terms of thermal stability and electrical characteristics.

Jan 1, 2010

By Jian Zhang

From the standpoint of quality, surface cracks normally pose more of a problem than internal cracks. Hypo-peritectic (HP) steel grades are well known for their proneness to surface longitudinal cracking (SLC) during continuous casting. This study analyzed the influences of chemical composition, technique parameter and secondary cooling on the surface longitudinal cracks. Based on the optimized the first and secondary cooling zone water distribution in the process of continuous casting, low cooling water distribution at solidification initial stages and uniform cooling at secondary cooling zone were suggested, which can be used to effectively control the surface longitudinal cracks.

Jan 1, 2010

By Guido Huillca, Gerardo Gonzales

Este documento presenta los resultados de un caso de estudio, que fue el producto de una ingeniería conceptual del diseño de la mezcla de relleno en pasta realizado para una mina polimetálica en el sur de Perú. El relleno en pasta es una mezcla de agua, cemento y relaves con alta densidad, que se utiliza en minas subterráneas como relleno en cavidades resultantes de la extracción de rocas (galerías, chimeneas, pozos, entre otros), proporcionando soporte para continuar con la minería y evitar un posible colapso

Sep 29, 2023

By Yi Luo, Jian Yang, Hua Jiang

Surface subsidence events induced by underground longwall coal mining operations can cause various disturbances to surface structures ranging from integrity and stability to functionality problems. Highway bridges, as a kind of special road construction that can only tolerate smaller movements and deformations than road pavements, are particularly susceptible to severe influence caused by subsidence-induced ground movements and deformations. However, based on accurate subsidence prediction and correct influence assessments, efficient and effective mitigation and remediation measures can be designed and implemented to ensure the continuous service of bridges, safety of the travelers and smooth mining operations. In this paper, based on the predicted final and dynamic surface movements and deformations, the techniques to assess subsidence influence on the integrity, stability and functionality of bridge structures (e.g., decks, beams, abutments, etc.) are presented. A number of mitigation measures to protect the bridge structures are recommended along with an actual application case.

By Piyush K. Dutta

This report describes the design, development and manufacture of production stoper drills and results of their field tests, it is shown that underground stoper drill noise level can be reduced from 118 dBA to below 100 dBA by using these pneumatic drills. The design concept of these drills is a radical departure from the standard valved rifle bar type drill machine design to a drill featuring a valveless independent rotation system, use of an integral muffler and a shroud tube. Six drills were manufactured in a standard commercial drill manufacturing setup and organization. The design and production technology proved that commercially viable quiet drills can be made available for mine use.

Jan 1, 1983

By A. Lawley S. Schuster

The tensile behavior of copper foils prepared from rolled bulk material has been studied over the thickness range 2 to 53 , and for a range of pain sizes. For foils of comparable grain size, having the cube texture and tested along (100), yield strength increases with decreasing foil thickness t below -26p, with a corresponding decrease in ductility. Deformation occurs in the form of localized slip clusters distributed throughout the gage section. To the extent that the tensile strength (10 to 18 kg mm-) is unaffected by foil thickness, and that the foils possess fair ductility, the stress-strain behavior resembles that of bulk material rather than that of whiskers or evaporated films of comparable dimensions. The dependence of yield strength o on foil thickness t below -26p is of the form: oy = oo + kt-1/2. Possible explanations for the stress increase are considered based on 1) the dependence of active dislocation source length on foil dimensions, 2) the locking of surface sources, or the blocking of mobile sources at the surface due to surface film. It is now well-established that filamentary whiskers of many materials show exceptionally high strength compared with bulk crystals.'-11 As the diameter of the whiskers decreases to -1, the observed fracture strength approaches, and in certain cases exceeds, the calculated shear stress for the nucleation of slip in a perfect crystal.' In general, the stress-strain curve is entirely elastic, with strains at fracture approaching 1 pct. Similarly, thin films12-24 of evaporated or electrodeposi-ted material have been shown to possess tensile strengths three to seven times that of bulk material, with total strains at fracture -1 to 2 pct. In the present study, attention has been directed to the room-temperature tensile behavior of thin foils of copper over the thickness range 2 to 53, prepared from rolled bulk material. Yield stress, ultimate tensile strength, elongation to fracture, and work-hardening behavior are measured as a function of grain size and foil thickness. Structurally such foils are superior to either evaporated or electrodeposited films, and in the recrystallized condition exhibit considerable ductility. Apart from preliminary work by Sumino and Yamamoto25 on the work-hardening behavior of rolled and recrystallized copper foils, no systematic tensile studies have been carried out on material of this form. EXPERIMENTAL PROCEDURE Tensile specimens were prepared from 99.995 pct purity rolled copper foils of thickness 2, 6, 12, 26, and 53, obtained from the Hamilton Watch Co., Lancaster, Pa. Irrespective of specimen shape, it is necessary to use tensile foils with edges free from notches or tears. To this end, any form of cutting operation was excluded, and the tensile foils prepared using a photoengraving process, the details of which are described elsewhere.26 Since tensile data are required under conditions of uni-axial stress, the specimen shape is extremely important. Ideally, the foil should be infinitely long, allowing a gradual taper from the grip area to the gage section; however, from a practical standpoint, long foils are easily damaged during testing. A modified tensile specimen was therefore selected having a parallel gage section 1.25 by 0.20 in. with a tapered shoulder section increasing to 0.5 in. at the grips, and an over-all length between grips of 4 in., Fig. 1. In practically all tests, these foils fractured within the parallel gage section. By approximating the foil contour (Fig. 1) to a hyperbola it is possible to analyze the stress distribution in the tensile foil using two-dimensional elasticity

Jan 1, 1964

By Peeler P. K

The recent renewal of interest in hydrometallurgical routes for copper production has been brought about by the possible future reliance on mixed ores and lower grade deposits, environmental aspects, and energy considerations.A number of hydrometallurgical processes for the recovery of copper have recently been proposed. Flowsheets are developed for two processes which incorporate several treatment methods being experimentally studied in Australia.In the first process a cupric chloride leach is followed by electrowinning whilst the second is based on the formation of cuprous ions, stabuized by acetonitrile and subsequent disproportionation to cupric ions and metallic copper. For the purpose of comparison, flowsheets were also developed for the Arbiter and Cymet processes.Process economics are estimated for the four processes and the results are discussed in relation to competitive pyrometallurgy. None of the four hydrometallurgical processes, with possible exception of the Cymet process, appears to be competitive with established large scale and newly developed pyrometallurgical processes for chalcopyrite.However, because the economics of the individual hydrometallurgical processes depend strongly on specific conditions, a "tailored" process may be competitive with pyrometallurgy in particular circumstances.

Jan 1, 1977

This Bureau of Mines report is a reference manual of procedures used by the Bureau's Twin Cities Mining Research Center for obtaining rock properties. Included in the report are discussions on the usage of each property, descriptions of the general test methods for obtaining the properties, and instructions for performing the tests. The Instructions embrace details of the specimen configuration, test apparatus, test procedure, test conditions, and calculations needed to achieve satisfactory results. Although the procedures presented in this reference manual generally conform to recommendations of the ASTM Administrative Committee on Standards, they are not purported to be standards.

Jan 1, 1974

By David Gatto, Nicolas A. Willig-Friedrich, Jeff A. Segar

"With the increasing demand for electricity, and requirements to generate this power cleanly, more producers are turning towards hydroelectric power. A project in Iowa currently under construction will retrofit an existing Army Corps of Engineers Dam with a hydroelectric generating facility. The design of the intake structure requires the construction of a diaphragm retaining wall. The T-shaped diaphragm wall elements retain an unbalanced fill height up to 21.3 meters (70 feet). The design required a single production element be constructed, tested, and instrumented prior to beginning construction of the rest of the elements. The testing included extensive concrete mix design development, coring, and Cross Hole Sonic Logging. Installed in the other production elements are 10 inclinometers, 4 pressure cells, 4 piezometers, and multiple survey monuments. Some of these instruments require manual readings while most are monitored by an automatic data acquisition system and instantly transferred to a website providing real-time graphical display of the data. This paper will discuss the construction of the diaphragm wall from the contractor’s perspective when working on a site only large enough for two service cranes and a Hydromill excavation unit, without any storage area on the construction pad, describe the testing performed and the quality control procedures employed, and investigate the information gained from the automated instruments providing real time measurement readings.INTRODUCTIONIn 1964 the US Army Corps of Engineers (USACE) constructed a dam by raising the surface grade approximately 34.7 meters (114 feet) above the natural ground line using a combination of fill types. This earthen dam stretched slightly longer than a mile intersecting the flow of the existing Des Moines River. The center of the dam is a concrete spillway consisting of 12 monolith sections. On each end, three of the sections extend 42.6 meters (140 feet) from the spillway to transition from the concrete dam sections to the earthen dam section. Adjacent to these three sections on the East end is where the contractor is actively working, for a private developer under a lease agreement with USACE, on this site to convert it to a Hydroelectric facility licensed for an output of 36.4 megawatts, enough power to meet the needs of about 18,000 homes. To create this, a powerhouse structure, housing two vertical Kaplan turbines is being added to the downstream side of the existing dam. From the power house, two penstock pipes will be cored through the existing concrete monolith sections and connect to the Intake structure on the upstream side of the dam. Protecting and reinforcing the dam adjacent to the intake structure is a new diaphragm wall. This wall is constructed using T-shaped diaphragm elements, acting as a cantilever retaining wall for the intake platform. Figure 1 shows a diagram of the upstream features of the construction."

Jan 1, 2016

By Jeffery L. Kohler

This final report on Bureau of Mines Contract J0338028 presents the results of a research effort to predict incipient failure in electric-power-system components. The development of continuous monitoring techniques to detect an incipient failure would represent a significant improvement in system maintainability, availability and safety, This report describes the analytical and experimental aspects of the project. Mathematical models have been developed to study the behavior of cables and motors which are undergoing a deterioration process. These models allow a detailed study of the effect of deterioration on the component's terminal characteristics and performance. The efficacy of using negative-sequence monitoring is a reliable indication of deterioration has been established. Techniques for assessing the sensitivity of the prediction algorithm to component deterioration have been presented. An approach for modelling electrically-excited vibrations, and including these in the algorithm, has been presented.

Jan 1, 1987

By José Wilmar Calderón-Hernández

Aços inoxidáveis supermartensíticos (AISM) são aços de matriz martensítica contendo baixos teores de carbono, abaixo de 0,03%. Eles vêm sendo utilizados na indústria de óleo e gás para aplicações específicas que exigem resistência mecânica aliada a moderada resistência à corrosão. Após serem temperados para a obtenção da estrutura martensítica, esses aços são submetidos a tratamento de revenimento para alívio de tensões e melhoria das propriedades de tenacidade e ductilidade. Durante o revenimento é esperada a ocorrência de mudanças microestruturais resultantes principalmente da precipitação de diferentes fases. Tais precipitados influenciam tanto as propriedades mecânicas finais quanto a resistência à corrosão desses aços. Nesta pesquisa foi avaliada a resistência à corrosão por pite de dois AISM do tipo 13Cr5Ni2Mo, um deles contendo Nb (0,11%), através de ensaios de polarização potenciodinâmica em soluções de 0,6M NaCl sem e com adições de 0,3M e 0,6M Na2SO4. Os resultados mostraram que a adição de Na2SO4 no eletrólito contendo NaCl inibe consideravelmente a corrosão por pite. Foi constatado também que o AISM contendo Nb apresenta maior resistência à corrosão por pite nos eletrólitos de misturas de cloreto e sulfato. Além disso, os resultados mostraram que o revenimento a 575°C melhora a resistência à corrosão por pite, comparativamente ao revenimento a 600°C. O melhor potencial de pite foi obtido para o aço ao Nb, revenido a 575°C por 2h, em eletrólito 0,6Na2SO4+0,6NaCl.

Jan 16, 2018

By E. S. Moore

Although nickel was in use in alloys long before the Christian era, the metal was not discovered until 1751, when Cronstedt recognized it in niccolite from Sweden. The Chinese apparently used a nickel alloy, known as "pahfong" thousands of years ago and Persian coins dating farther back than 200 B.C. consist of a copper-nickel alloy similar to some of those now in use in coins. The pure metal was first prepared about 1775 and the metal was refined for commercial purposes some years later. The nickel industry did not attain much prominence until the ores in New Caledonia were discovered. Exports of ore from that country began in 1875 and since that date there has been an ever-increasing world output of nickel and a great expansion in the uses of the metal except during short periods of commercial and industrial depression. Previous to 1875, for a number of years, Norway was the chief producer, although the metal was mined also in Sweden, Finland, Italy, Germany, Austria, France, China, the United States and other countries. With the discovery of nickel deposits in the Sudbury district, Ontario, a new factor was introduced into the nickel industry and Sudbury has since become the overwhelmingly dominant feature in the world's nickel markets. Although nickel was first discovered in Canada as early as 1848 near the north shore of Lake Huron and nickel-copper sulfides were found in 1856 by surveyors working close to the present location of the important rnine at Creighton, in the Sudbury field, it was not until 1883 that any importance was attached to this field. In that year copper sulfide attracted attention where the main line of the Canadian Pacific railroad was being projected across Canada to the Pacific coast. Mining began near this discovery in 1889 but in the meantime operations had begun in 1886 in other parts of the field and by 1890 about 100,000 tons of ore had been raised. In the Sudbury field, as in Norway and at the old Lancaster Gap mine in Pennsylvania, the ore was first mined for its copper content and difficully in the refining of the copper led to the discovery of the important proportions of nickel in the ore. No. 3 property of the International Nickel Co., now known as the Frood, the greatest deposit in the

Jan 1, 1932

By E. S. Moore

ALTHOUGH nickel was in use in alloys long before the Christian era, the metal was not discovered until 1751, when Cronstedt recognized it in niccolite from Sweden. The Chinese apparently used a nickel alloy, known as "pahfong" thousands of years ago and Persian coins dating farther back than 200 B.C. consist of a copper-nickel alloy similar to some of those now in use in coins. The pure metal was first prepared about 1775 and the metal was refined for commercial purposes some years later. The nickel industry did not attain much prominence until the ores in New Caledonia were discovered. Exports of ore from that country began in 1875 and since that date there has been an ever-increasing world output of nickel and a great expansion in the uses of the metal except during short periods of commercial and industrial depression. Previous to 1875, for a number of years, Norway was the chief producer, although the metal was mined also in Sweden, Finland, Italy, Germany, Austria, France, China, the United States and other countries. With the dis-covery of nickel deposits in the Sudbury district, Ontario, a new factor was introduced into the nickel industry and Sudbury has since become the overwhelmingly dominant feature in the world's nickel markets. Although nickel was first discovered in Canada as early as 1848 near the north shore of Lake Huron and nickel-copper sulfides were found in 1856 by surveyors working close to the present location of the important mine at Creighton, in the Sudbury field, it was not until 188.3 that any importance was attached to this field. In that year copper sulfide attracted attention where the main line of the Canadian Pacific railroad was being projected across Canada to the Pacific coast. Mining began near this discovery in 1889 but in the meantime operations had begun in 1886 in other parts of the field and by 1890 about 100,000 tons of ore had been raised. In the Sudbury field, as in Norway and at the old Lancaster Gap mine in Pennsylvania, the ore was first mined for its copper content and difficulty in the refining of the copper led to the discovery of the important proportions of nickel in the ore. No. 3 property of the Inter-national Nickel Co., now known as the Frood, the greatest deposit in the

Jan 1, 1932

By Javier Enrique Basurco Cayllahua

In this work, a gram-positive bacteria was used as biosorbent to elucidate the aluminum load capacity under different conditions related to metallurgical and chemical plants. The sorption data followed the Langmuir, Freundlich, Dubinin-Radushkevich isotherms. In order to determine the best isotherm fit, three error analysis methods were used to assess the data: correlation coefficient (R2), residual root mean square error (RMSE) and Chi-square test. The error analysis established that the Dubinin-Radushkevich model fits better the aluminum biosorption data. The maximum sorption capacity was found to be 41.59 mg.g-1. The maximum removal of aluminum was 95% at pH around 5. The experimental kinetics data was evaluated considering two models (pseudo-second order and pseudo-first order). This study indicated that the R. opacus is an environmental friendly biosorbent.

Jan 1, 2009

With IIT research institute as a cosponsor, this seventh mineral waste Utilization Symposium was funded by the Bureau of Mines through its Division of Mineral Resources Technology. Environmental scientists and engineers from five countries (Canada, Netherlands, Austria, England, Guatemala) besides the United States participated in the symposium, which was held Oct. 20-21, 1980, at the Chicago campus of IIT Research Institute. Of the 25 papers presented on the reclamation and recycling of mining and mineral wastes, municipal solid waste, industrial waste, and scrap metal, 21 are summarized herein.

Jan 1, 1982

By S. Vongpaisal, T. R. Yu

"A set of new blast damage criteria has been developed, with special reference to blasthole mining operations, for assessing damage by incorporating the vibration level, rock properties, site characteristics and the effects of ground support systems. The main objective of this work was to provide a database with reasonable accuracy for use in optimizing blast design, numerical analysis and ground control expert system module development.The new damage criteria allow one to estimate the degree of damage to rock structures in terms of a dimensionless parameter defined as Blast Damage Index (BDI). This allows for the description of blast damage in a unified form, and facilitates the development of codes for numerical modelling to express the degree of blast damage universally. A number of field investigations from several stope production and slot opening blasts at a large underground base metal mine were carried out to verify the developed index. The results show a good correlation between the observed damage and the type of damage predicted from the BDI values.Practical measures are also provided for minimizing blast damage in large underground blasthole mining operations"

Jan 1, 1996

By Arthur Mackwell

The role of the precious metals is changing rapidly. They are becoming primarily materials of modern industry, and their decorative and monetary functions are diminishing in relative importance. Certainly gold is still the premier metal for jewelry, as silver is for silverware. But these uses are not growing nearly so fast as are the uses of these metals in a variety of industries. This is even more true of the platinum metals. Moreover, this is true despite the fact that the precious metals are highly expensive and liable to substitution by the base metals in cases where this is feasible. For the fact is that the physical and chemical properties of the precious metals make them relatively invulnerable to substitution; where they can be replaced by the base metals, they have been, and the opportunity for further substitution is, therefore, limited. SILVER In November 1969 the United States Treasury stopped minting the only remaining coin with any silver content. That was the silver-clad Kennedy half dollar, which had a silver content of approximately 40%. The step was taken out of necessity, because of the rising shortfall between world mine production and consumption. It was important to divert the 35 to 40 million oz of silver per year used for the minting of this coin into the open market, where it would be available for industrial consumption. This decision was important, not only for its practical effect but also for what it symbolized. Only four years earlier, in 1965, the Treasury had used 320 million oz of silver" for the full range of coinage. Now not an ounce of silver goes into the United States coinage. The reason is simple and yet complicated. For many years the U.S. Treasury had purchased silver at prices which provided a subsidy to domestic producers. As a result, silver producers were eager to sell to the Treasury, and that agency built up a huge supply of the metal -almost 2 billion oz by- 1961. But, as the free-market price neared $1.29, the basic melt value of the coinage, the Treasury became a seller of silver, not a buyer, and its stock was depleted rapidly. The Treasury lost more :than a billion ounces of silver in the years 1962 through 1965, and it continued to lose silver, both through coinage and through sales to consumers, through 1969. The Government continued to sell silver to consumers at the rate of 1.5 million oz a week, even after terminating the 40% silver Kennedy half dollar. But it was apparent that the Government stocks could last no more

Jan 1, 1976