Search Documents

By L. Yan, N. Damiano, J. Bickson, E. Bauer, D. Yantek, B. Whisner, M. Reyes, J. Srednicki

Built-in-place (BIP) refuge alternatives (RAs) are designed to provide a secure space for miners who cannot escape during a mine emergency. Heat and humidity buildup within RAs may expose miners to physiological hazards such as heat stress. To minimize the risk of heat stress, Title 30 Code of Federal Regulations (CFR), or 30 CFR, mandates a maximum allowable apparent temperature (AT) for an occupied RA of 35°C (95°F) [1]. The National Institute for Occupational Safety and Health (NIOSH) has conducted extensive research on the thermal environment of occupied RAs intended for use in underground coal mines. NIOSH research has demonstrated that a fully occupied BIP RA can exceed the AT limit by >5.6°C (10°F) in mines with elevated mine strata and air temperatures. In this circumstance, an RA cooling system could provide a solution. This paper provides an overview of test methodology and findings as well as guidance on improving the performance of a cryogenic air system prototype by optimizing the flow rate, increasing the tank storage capacity, and improving the efficiency of the heat exchanger of the cryogenic system. This may enable BIP RAs to meet the 35°C (95°F) AT limit in mines with elevated temperatures. The information in this paper is useful for RA manufacturers and mines that may choose to implement a cryogenic air system as a heat mitigation strategy. INTRODUCTION The apparent temperature inside an occupied RA could be significantly affected by the surrounding environment’s thermal conditions, such as mine air temperature and mine strata temperature. Apparent temperature (AT) is a temperature-humidity metric for the perceived temperature caused by the combined effects of air temperature, relative humidity (RH), and air velocity. It is used to assess the perception of indoor temperatures. Depending on factors such as geographic location and season, mine air temperature, relative humidity, and mine strata, temperatures can vary significantly [2]. RAs located in cold mines may pass the 96-hour 35°C (95°F) AT limit test that poses a challenge for RAs located in hot mines. One solution in these cases is that the occupancy of the RA could be derated (i.e., the RA occupancy could be reduced) to ensure the AT limit is not reached. However, this would require mines to purchase additional RAs to accommodate all personnel in the mine. For mines with high temperatures (above 26.7°C or 80°F), the occupancy might have to be reduced so much that the necessary number of additional RAs would be impractical. In these cases, RA cooling systems could provide a solution.

Jan 1, 2019

By Joe Roby

Rolling disc cutters are the business end of hard rock and mixed face tunnel boring machines (TBMs). Since their first successful employment on a TBM over fifty years ago, disc cutter technology has constantly evolved, allowing modern TBMs to excavate very hard and abrasive rock efficiently. Disc cutters have also been employed successfully on earth pressure balance (EPB) and slurry machines, cutting rock under water and ground pressure. The range of materials excavated by machines today is broader, excavation rates higher and cutter costs lower than ever before, proving the value of investment in cutter development. This paper describes recent improvements in disc cutter components including cutter ring materials and processing, as well as improvements in lubricants, bearings, seals and cutter condition monitoring. These developments have resulted in more reliable cutters capable of operating in a wide range of geological conditions. Ultimately these improvements result in a better value for both contractors and project owners.

Jan 1, 2008

By J. H. Daniel

The reduction of accidents will play an ever increasing role in the mining of coal and hardrock ores as mining operations become more mechanized, the equipment becomes more costly and sophisticated, and as mineral production exploits deeper and more marginal coal and ore deposits. The most effective means to reduce accidents is through the design of mining systems and equipment. Results of safety research by the U.S. Department of the Interior, Bureau of Mines, to design safer coal extraction and haulage systems and to reduce electrical accidents are presented.

Jan 1, 1991

By W. L. Zhong

Probability function integration method is one of the influence function method. It is a widely accepted method in many mining districts in China and Poland mainly because its theory and formulae can well-represent the surface subsidence basins due to longwall mining of flat or near-flat seams. This paper introduces the basic theory of the probability function integration method and determines its 4 basic parameters by analyzing the measured subsidence profiles in eight longwall panels in Northern Appalachian Coal field. It also discusses the two methods for determining the 4 parameters. Finally the acquired parameters are used to predict the subsidence and deformation of the houses for damage assessment. Comparisons are made between the measured and the predicted subsidence. Probability Function Integration Method The probability function integration method for predicting surface movements and deformations is widely used in China and Poland. The governing equation of the method contains five parameters: subsidence factor, a, offset of inflection point, d, tangent of the major influence angle, tan fl, horizontal movement constant, b, and major dispersion angle e (e = 90. for flat seams). Its applicable range iis much larger including seams less than 30' from the horizontal, critical and noncritical mining and soft to hard overburden.

Jan 1, 1986

By Yury Kapelyushin

Formation of cementite in the reduction of hematite by CO–CO2 gas was studied in situ using high temperature XRD (HT XRD) analysis. Reduction of hematite was examined in the temperature range 873–1173 K by CO–CO2 gas mixture with high carbon activity. When carbon activity in the system was 1.5, cementite was formed only at 1023 K; it was not observed in experiments at 973, 1073 and 1123 K. Formation of cementite was observed at 923–1073 K when carbon activity increased to 3–5; and at 873 K when carbon activity was 10. Formation of cementite at 973–1073 K proceeded through metallic iron; however, in the reduction of hematite at 873 and 923 K, iron was not observed; cementite apparently was formed directly from wüstite. XRD spectra were used to estimate concentration of carbon in austenite in the process of cementite fromation.

By A. McQuillan, N. Bar

Geotechnical models developed during the planning stages of open pit mines are three-dimensional so as to capture the spatial variation in lithological, structural, hydrogeological, and geomechanical conditions. Geological models that describe the lithological and structural (faulting and folding) characteristics of a deposit are always 3D. Likewise, boreholes and piezometers used to develop geomechanical properties and groundwater models are drilled at spatial offsets across the deposit to understand the lateral and vertical characteristics. Yet when geotechnical analysis is completed, often the three-dimensional geological, hydrogeological, and structural models as well as geometrically complex 3D mine designs for optimizing economic mineral recovery and overburden removal are simplified to two-dimensional sections. In this paper we demonstrate that this simplification can lead to the wrong failure mechanism being identified, analysed, and/or a conservative factor of safety being calculated and hence an over-estimation of slope stability. Through case studies we show how three-dimensional analysis methods are more suited to rock slopes, particularly those with anisotropic material strength, when singularities such as geological faults are present, and nonlinear slope geometry. When the same slopes are analysed in two dimensions, the failure mechanism calculated is often fundamentally incorrect. The case studies further reveal that the factor of safety calculated in three dimensions is not always higher than the two-dimensional factor of safety.

Feb 6, 2023

By R. J. Fantel

The Bureau of Mines investigated the resource potential of 201 mines and deposits in 28 market economy countries and 17 mines and deposits in the U.S.S.R. and China. The 201 mines and deposits evaluated from market economy countries contain an estimated 34.2 billion metric tons of recoverable phosphate rock (at the demonstrated resource level), with Morocco and Western Sahara accounting for 61% (21 billion tons), followed by the United States with 19% (6.4 billion tons). The 17 mines and deposits evaluated in the U.S.S.R. and China contain approximately 1.5 billion tons of potentially recoverable phosphate rock. Potential annual capacity from low-cost, high-grade producing mines in the United States is estimated to decline significantly during the latter half of the next decade, and the United States will have to develop new, higher cost, lower grade mines in order to satisfy demand into the next century. Of the world's new production capacity which could likely be developed over the next decade, slightly over one-third could be produced at an estimated 1981 cost of $40 per ton or less, and about two-thirds would cost in the $40 to $50 range (including a 15% rate of return). In comparison, moot of the competing phosphate rock from producing mines in Morocco could be produced for under $40 per ton. The United States has sufficient demonstrated resources of phosphate rock (plus huge quantities at the identified and hypothetical resource levels) to satisfy domestic consumption for many years to come, but its future ability to compete in the major export markets against low-cost competitors is much more uncertain.

Jan 1, 1984

By John T. Metcalf

The assembly procedures for nine different wire rope terminations used in the mining industry are presented in a format and manner to facilitate training and to provide points where inspection of the termination should be performed. The nine terminations addressed are: Flemish Loop with Steel Sleeve & Thimble, Flemish Loop with Steel Sleeve, Wedge Socket, Swaged Socket, Turn Back Loop with Sleeve & Thimble, Thimble Splice with Four Tucks, U-Bolt Clip & Thimble, Zinc Poured Socket, and Epoxy Resin Poured Socket. The manual was prepared to be used primarily for field type mining operations or training where high capacity machinery is quite limited. It is nut the intent of this manual to suggest that the procedures presented are those to be used by manufacturers or other commercial enterprizes. A different set of procedures may be more appropriate where ideal space and equipment resources are available. The assembly procedures were derived from standard industrial practice, manufacturer's recommendations, and the open literature on the subject. These same procedures were used to prapare test specimens for an extensive series of pull and axial fatigue tests. The results of these tests indicate that these procedures are satisfactory in all respects. This manual is to be used as part of a complete training program. Although a brief glossary is included, there has been no attempt to make this a primer on wire rope. The selection of wire rope termination hardware, like the selection of the wire rope, is a subject not covered by this manual. The reader is cautioned that there are various sources for such hardware and this selection must be done carefully.

Jan 1, 1978

By J. C. Fowler

The field testing of the Seismic Mine Monitor System is described. This system consists of nine geophones buried about 40 feet deep over a ten-square-mile area, the amplifiers and electronics needed to get the signals to the mine office, and a central processor unit to detect and locate explosions and large roof falls. Since the problems associated with the original installation were solved, this system has worked for 2 1/2 months. The system has detected roof falls in the pillar areas and has located blasts as small as 114 pound of dynamite. The location accuracy has, in general, been within 250 feet. The system is now being used to gather long-term data on the seismic activity of the mine.

Jan 1, 1974

By Kenneth C. Ko

An engineering investigation was carried out on the technical and economic feasibility of implementing flexible liner/backpacking support systems In an advancing tailgate longwall mine. The system for a model mine consists of a circular tube constructed of liner plates and flyash backpacking. Flyash is pneumatically stowed into the tailgate. Small amounts of cement may be mixed to improve the support capability of the fill In difficult local ground conditions. Water is added inside the nozzle immediately prior to spraying. Results of theoretical analyses and a field test show that the designed system is technically feasible, can be cost-competitive, provides more stable ground conditions, and can Increase productivity and coal recovery, when compared with existing retreat longwall systems. In certain mine layouts, the new system can reduce the direct mining costs by a significant amount. The system would be particularly applicable to deeper coal beds with bad ground conditions.

Jan 1, 1980

Thermal method of diagnostic as a nondestructive monitoring is based on data logging of infrared radiation from heated surface or from the associated thermal field. Monitoring of gearcases and motors hidden faults, such as, bearing degradation (deep-seated wears and tears, fretting wear, spalling and jamming solids of revolution) is closely related to high variations in temperature. The use of portable thermal imaging devices provides considerable advantages due to: easy remote access to the unit under test even when it is operating; minimum time required to obtain information and an opportunity for a real-time diagnosis of the tested subject's condition.

Dec 6, 2010

By Joanna LaForte

"IntroductionIn respect to The Human Dimension by M. Phyllis Bray, this author's impression is that research on long distance commuting (LDC) is long overdue. This type of mining is not new to many workers, especially those from areas such as the Maritimes, who have had to look for work away from their families for at least a decade. Perhaps to the industry the over-all set-up is new, but to workers who have faced mine shut-downs in their areas finding a job was the main objective and if the security of long-term employment was evident, then the families might join them later. This was the situation with which the writer' s family was faced.LDC LifestyleBeing the wife of an underground miner, the author has personally experienced this lifestyle for almost 10 years, and has never experienced accommodation in a company town. The first five years of marriage were spent in a small rural municipality within 50 miles of the worksite, but the town had industry separate from mining and was not affected by the mine shut-down.Since her LDC lifestyle began her family has been pretty much city-based, out-of-province commuters with two children and a third to arrive some years later. She therefore lived a fairly normal married life with a husband home daily. The author has experienced life with a husband who worked away for five-day stretches and then drove long distances to be home weekends or the portion of time left over from driving and fatigue. She has done the 3D-days in/l4-days out routine, and for approximately the past four years has been existing on a two-weeks in/two-weeks out ritual .The author does not agree that the ""bottom line is that mining families go where the jobs are"" . The miners go where the jobs are and the families fend for themselves with the assistance of the pay cheque making it home each pay period.Perhaps because there are many personal frustrations with this type of lifestyle, perceptions may be inaccurate. Having only dealt with underground operations, there may be gross differences between the pressures and demands of other forms of mining."

Jan 1, 1991

By M. O. Serbousek

The load-transfer mechanics of fully grouted roof bolts in coal mines have been investigated in laboratory and analytical studies. The purpose of this Bureau of Mines research is to increase understanding and better interpret data from routine field pull tests and to develop a numerical model of a grouted bolt that can be used in a global computer model of a mine roof. Analytical studies using closed-form solutions and finite-element techniques were compared to experimental results. Laboratory work includes variation of bolt length, hole diameter, and grouL type. Pull tests were pel'fol·med on 4-, 2-, and I-ft bolts in holes of 1-and I-3IB-in diameters. Both polyester resin and inorganic grouts were used as the anchorage medium. Strain gauges were installed on the bolts at several locations to observe the rate of load transfer from the bolt through the grout to the rock mass when a force was applied at the bolt end using standard jack pull testing procedures and equipment. The average anchorage length of 4-and 2-ft bolts was 22 in. Grout type and hole size variations did not produce a significant effect on the rate of load transfer from the bolt to the rock.

Jan 1, 1987

By John M. Devine

The severe corrosion of equipment that is caused by the presence of hydrogen sulphide in oil and gas has been described in detail by several authors.5 Such corrosion, termed "low-temperature hydrogen sulphide corrosion", presents a somewhat different problem from the "high-temperature hydrogen sulphide corrosion" that is encountered in refinery operation and

Jan 1, 1932

By A. D. Kalogeropoulos, T. N. Michalakopoulos

This paper deals with the numerical simulation of rock cutting laboratory tests using the discrete element method. The main objective is to provide a method for calibrating numerical DEM models of rock cutting in a systematic way so that realistic results are yielded. The numerical models are developed with the discrete element code Yade, which models rocks as a collection of bonded spheres. The models are calibrated in a four-step process based on the design of experiments method and optimization. The calibrated models are evaluated both quantitatively and qualitatively against actual laboratory cutting tests, in terms of the ratio of the simulated mean cutting force to the actual one and the cutting force time series, respectively. The fully calibrated models showed that the simulated cutting process matched qualitatively the actual cutting force recordings and underestimated the mean cutting force by approximately 3%. It is concluded that well-calibrated numerical simulations of the rock cutting process can provide not only a better understanding of the process itself but also quantitative data regarding the cutting force and energy requirements.

Dec 28, 2022

By Normal Seidle

This report (rind related Appendices) provides a description of the functional design specifications and related rationale for development of a training system for dragline equipment operators. Phase I activities involved a delineation and detailed analysis of specific behavioral requirements for successful dragline operation. Following the field data collection effort, job/activity/task descriptions were formulated into training requirements which can be achieved by a trainee with training hardware having specific functional capabilities. The training system analysis integrated the training requirements and the trainer functional capabilities into recommendations which configure a total training system. The objective of the training system described in this report is to provide new operators of dragline equipment with the requisite skills and knowledge to assure cost-effective development and an adequate supply of our human resources.

Jan 1, 1975

By C. Doyle, J. Brennan, C. Díaz, J. Hrepic, K. Cushnie

"In 1991/1992, INCO undertook a successful R&D program aimed at extending the lining lives of the top blown rotary converters (TBRCs)at its Copper Cliff Nickel Refinery (CCNR) and the electric furnace at INMETCO. At the laboratory scale, this effort was divided into three phases. In the first part, mineralogical work was performed on six refractories that were either currently being used to line these vessels or were considered suitable alternatives. In the second part, this mineralogical knowledge was used to help determine the compositions of slags that would not corrode the bricks at the operating temperature (1600°C) of the above furnaces. Finally, several important properties of the six refractories were measured to complete their evaluation as candidate linings. This paper reports the results of all three phases of the laboratory scale R&D work.The mineralogical work showed that rebonded fused grain magnesite-chrome (RFG-MC) bricks consist principally of periclase with minor amounts of free chromite and trace quantities of silicates monticellite and sometimes olivine. The bricks are principally held together by periclase-periclase direct bonding. Of note, the bulk of the chromite exists as exsolved precipitated blebs within the periclase grains. These likely redissolve at high temperature.Slags on the periclase liquidus coexist stably with these refractories. Examples are presented using CaO-MgO-Al2O3-SiO2 slags at~1600°C.Finally, the two refractories manufactured using close to 100% fused grain material generally outperformed the others in terms of physical properties and certainly were superior in their resistance to slag penetration damage."

Jan 1, 1997

By D. R. Mathews

The solubility of carbon in electrorefined vanadium was determined to be approximately 0.27 wt pct at the eutectic temperature 1,650° C and 0.03 wt pct at 700° C. The tensile strength and hardness of vanadium increased with car-bon content to the solubility limit, but this effect was small, probably because of the narrow solubility range. Between the solubility limit and 0.3 weight-percent carbon, the second phase had essentially no strengthening effect in vanadium. The second phase, observed metallographically at the grain boundaries and within the grains, was shown by autoradiography to contain high-carbon concentrations. This second phase was identified as VgC by X-ray analysis. The VgC in the grain boundaries contributed largely to the poor cold-and-hot workability of vanadium-carbon alloys. Increased concentrations of V2C occurred at the grain boundaries of the high-carbon alloy ingots as a result of homogenization at 1,600° C for 1 hour. Alloy ingots containing more than 0.36 wt pet carbon (a calculated 2.9 wt pct VaC) following homogenization, cracked severely and failed by intergranular fracture upon swaging at 900° C.

Jan 1, 1965

By J. V. Wood, P. Davies, J. L. F. Kellie

A new range of wear-resistant materials is being produced by technology that has been used to develop high performance metal-matrix composites. These include steels and aluminium alloys that can be made as sheet, plate, rod or bar. The incorporation of hard, wear-resistant particles in an alloy matrix is achieved by reactive casting, spray deposition and powder metallurgical techniques. For example, large particles of TiC can be homogeneously distributed in steel during casting and the subsequent product can easily be rolled to plate. Similarly, up to 20% alumina particles and SiC can be injected, respectively, into steel and wear-resistant aluminium alloys by spray deposition. The current state of development of the process is reviewed and indications are given of the projected applications of such materials.

Jan 12, 1992

By T. R. Kostecki, A. J. S. Spearing, A. Hyett, M. Gadde

Ground control research for underground coal mining has progressed significantly over the past several decades. With this progression, and the ability to analyze and model underground conditions, underground working conditions have significantly improved. In order to progress further, the behavior of roof support must be known and be adequately modeled, such that models can be used for support design under different geological and mining conditions. This paper discusses the results from a research project funded by the U.S. National Institute for Occupational Safety and Health (NIOSH) and undertaken by Southern Illinois University Carbondale and Peabody Energy. The research involved installation of active and passive instrumented bolts in mines, recording relevant in situ data and then attempting to model the behavior of the bolts as mining progressed. Such calibrated models could aid in design of roof supports under different geological and mining layouts and thus, hopefully, further improve rock related safety.

Jan 1, 2012