Search Documents

By James Warner, Peggy Ganse, Glen Smoak, Raymond Henn, Sam Bandimere

Over the past several decades, cement-based grouts using ultrafine cement as are placement for portland cement have begun to gain acceptance as an alternative to chemical solution grouts, however the amount of information currently available on these grouts is limited. For this reason, the authors developed a field testing program to evaluate the penetration capabilities of various ultrafine cement grout mixes. The tests were conducted by injecting sand columns using different portland and ultrafine based grouts, the measuring penetration distances after applying equal injection pressure for the same time period. Results of tests performed in 1999 and 2000 are discussed herein.

Jan 1, 2001

By J. F. Lupo

Heap and valley leach operations rely on solution collection piping placed within the heap to enhance both solution recovery and to assist overall solution management. The most common piping used in leaching operations is solid or perforated High Density Polyethylene (HDPE) pipe and Corrugated Polyethylene pipe (CPE). These pipes are widely used because of their low cost, ease of installation, durability, and flexibility. The typical recommended maximum design depth of burial for HDPE and CPE pipes is on the order of 30 meters (100 feet). However, ore heap heights at many facilities exceed 30 meters and some are now approaching 180 meters (600 feet) in height. At very high ore heap heights, the stability and performance of HDPE and CPE pipes becomes a critical issue for leaching facility design and operation. Failure of solution collection piping can lead to poor solution recovery, high hydraulic heads on the liner system, and in some cases, unstable ore slopes due to high solution pressures near slopes. This paper presents a review of methods that have traditionally been used to evaluate pipe stability under high normal loads. A common shortcoming of these methods is the inability to account for beneficial effects of ore arching around pipes and the time-dependent creep (stress relief) behavior of polyethylene (PE) materials. A new analytical approach is developed and presented which includes the effects of ore arching around pipes and creep of PE materials. The results of the new approach show that PE pipes will deform under high heap loads, but can remain stable and functional. Pipe stability is shown to be dependent on the type of pipe backfill and initial backfill compaction. The new approach represents a useful tool for designing applications for PE pipe under high normal loads.

Jan 1, 2001

By Baojie Zhang

The main goal of this study was not only to investigate the effectiveness of the FGX Dry Separator for removing pure rock from run-of-mine coal producing a better feed stock for conventional coal preparation plants but also to optimize the FGX Dry Separator performance for producing a salable clean coal product without using the conventional wet coal preparation processes. A Model FGX-1 Dry Separator with feed throughput capacity of 10 tph was extensively tested at the Illinois Coal Development Park using two coal samples having distinctly different cleaning characteristics. Statistically designed experimental programs were conducted to indentify critical process variables and optimize FGX Dry Separator performance by systematic adjustments of critical process variable parameters. The coal cleaning performance of the FGX Dry Separator was evaluated for the particle size range of 63.5 x 4.76 mm in most cases, although FGX Dry Separator feed consisted of nominal -63.5 mm run-of-mine coals. The best cleaning performance obtained from the FGX Dry Separator is described by specific gravity of separation (SG50) and probable error (Ep) values of 1.98 and 0.17, respectively. The SG50 and Ep values for individual size fractions were as follow: 1.90 and 0.12 for the +50.8 mm size fraction, 1.95 and 0.18 for the 50.8 x 25.4 mm size fraction, 2.01 and 0.19 for the 25.4 x 12.7 mm size fraction, and 2.03 and 0.23 for the 12.7 x 4.76 mm size fraction. These process efficiency measures produced a clean coal with ash content of 13.38% from a feed coal with ash content of 34.45%. Ash content of tailings and middlings streams were 85.09% and 39.57%, respectively. Total sulfur contents of corresponding streams were 3.87%, 4.68%, 6.87%, and 4.62%. For a relatively easy to clean Illinois No 6 seam coal (Cleaning Index: 0.72), only about 0.42% of the clean coal (i.e., 1.6 float fraction) present in the feed was lost to the tailings stream. For a relatively difficult to clean coal (Cleaning Index: 0.53), about 0.98% of the clean coal present in the feed was lost to the tailings stream.

Jan 1, 2012

By Wern-Ping Nick Chen

Durability risks for underground facilities can be underestimated during design phase as compared to well-known geological risks. However, unclear durability requirements can result in construction schedule delay and change orders. Unlike bridges or buildings, a unified underground durability code or standard does not exist. This paper will provide a durability approach for underground facilities, including degradation modes, mitigations, and compliance measures during construction. In addition, this paper will address how to clearly specify durability requirements in a contract document to reduce disputes during construction and discuss key durability tests that are time consuming and will impact construction schedule if not timely planned.

Jun 23, 2024

By Timothy J. Matthews, Timothy J. Batchler, Daniel J. McElhinney

The National Institute for Occupational Safety and Health’s (NIOSH) Mine Roof Simulator (MRS) at the Pittsburgh Mining Research Division was commissioned for operation in 1981. The MRS was originally designed for longwall shield research and was the only hydraulic press in the world with the capability to apply biaxial loads to these large structures. The results of this forty-year research program have contributed to improved performance and increased knowledge of longwall shields, mobile roof supports and hydraulic cylinders in the mining industry. Also, considerable research and development have been conducted to develop standing support technologies for the mining industry. The Support Technology Optimization Program (STOP) was developed to evaluate how these various technologies can impact and improve both ground control conditions and mine safety. Additional MRS research has included the performance of ventilation stopping walls including the development of a new testing protocol to evaluate the transverse loading capabilities under arching load conditions and evaluating the performance characteristics of welded wire screen as used in underground mine roof surface control. The NIOSH Mine Roof Simulator has been a reliable and valuable tool for the past forty years for the evaluation of safety structures used in mining, and this research has contributed significantly to the advancement toward safer mines. This paper will summarize those research results and provide a glimpse of planned future activities.

By L. A. Panek, F. D. Wang, M. C. Sun

A method of stability analysis of underground opening by the limiting equilibrium approach is presented. The Coulomb shear failure criterion is employed to find possible fracture surfaces and to evaluate the shear strengths along them. The normal stresses required for the calculation of shear strength, and the shear stresses for the calculation of total shear force along the fracture surfaces, are obtained by the finite-element method of plane-strain analysis. The factor of safety against Coulomb shear failure is calculated as the ratio of the shear strength to the shear force along a fracture surface, similar to the practice in slope stability analysis. Four shapes of openings are analyzed, with three ratios of horizontal lithostatic stress and four coefficients of internal friction. The critical fracture surfaces found by this method of analysis are consistent with the arching of roofs and slabbing of ribs commonly observed.

Jan 1, 1972

By D. H. Yardley

A major purpose of this contract was to evaluate a variety of dust suppressants to determine their effectiveness in mitigating dust from taconite tailings. During the course of the investigation tailings from pilot-plant tests of Minnesota copper-nickel ores became available and chemical binders were also tested for dust mitigation effectiveness on this mineralogically different material. Field-test plots were established on taconite tailings and wind tunnel laboratory tests conducted. The laboratory tests consisted of comparing treated and untreated samples at wind velocities of 40 mph using a weight-loss method and direct dust emission measurements. It was shown that the emission of fine dust from taconite tailings, in the range of 4.5 microns to 0.85 microns, could be reduced by 99 percent using certain chemical suppressants. It was also demonstrated that a straight water spray on coarse tailings (3/4" to + 10 mesh) reduced dust emission by 95 percent. Although eight different chemicals were tested, most of the tests were made using Coherex, ammonium lignin sulfonate and sodium silicate. These same dust suppressants were used, singly and in combination on almost 75 field-test plots. The Coherex appears to provide the best results in terms of economics and durability. Wind tunnel tests on treated and untreated Cu-Ni tailings demonstrated that applications of dust suppressants reduced fugitive fine dust by better than 99 percent.

Jan 1, 1980

By K. Peake, A. Dalvi, V. Hernandez, S. Chang, M. Oliazadeh

"Ironstone Resources Ltd. is developing the Clear Hills oolitic iron ore deposit in northwest Alberta, Canada. Sources of oolitic iron ore worldwide are abundant and ubiquitous, but there is currently no commercial technology to extract iron from oolitic iron ores. Mineral processing of the ore to generate a commercial iron ore concentrate is very challenging due to the nature of these ores. Accordingly, Hatch and Ironstone are developing a new pyrometallurgical process (Hatch Ironstone Chloride Segregation) to produce metallic iron from high silica and high phosphorus oolitic iron ores. Following the chloride segregation process, the treated ore is subjected to fine grinding. The iron is then separated by magnetic separation. The iron grade and phosphorus content of the final product shows a strong dependence on the separation methodology and the grind size. The pyrometallurgical process has been developed and tested at a lab-scale pilot plant. The commercialization of this technology could provide an opportunity for the development of a new alternate iron making technology. This paper presents the results of test work done on the raw iron ore to create a concentrate and also on the products of the pyrometallurgical process for the production of a high grade 90% metallic iron product.INTRODUCTION Oolite is a sedimentary rock formed from ooids – spherical particles with concentric layers. There are a number of large oolitic iron deposits where the mineralogical form features a low iron content and high concentration of impurities making them presently impossible to exploit on either a technical or economic basis. The fifteen largest oolitic iron ore deposits in the world are estimated to contain approximately 337 billion tonnes of iron ore, which would be a significant source of supply for worldwide steel production. A viable process that can economically recover iron from these oolitic iron ore deposits could become an important new technology to meet future demand in the steel industry. Hatch and Ironstone have demonstrated that oolitic iron ores can be exploited to produce direct reduced iron (DRI). Direct reduction ironmaking is a method for producing solid metallic iron using different techniques compared to the blast furnace process, which is the more conventional ironmaking route. The demand for the construction of direct reduction ironmaking plants has increased in response to the increasing demand for crude steel. It is viewed as a method of providing low-residual iron sources to scrap-based steelmaking in electric arc furnaces."

Jan 1, 2014

In the past two and a half years, over 40 000 metalliferous mining and related services personnel have been trained through an Australian Generic Safety Induction system. This is almost half of AustraliaÆs metalliferous mining related workforce. This remarkable industry acceptance and delivery of safety courses is supported by Acacia Resources, Great Central Mines, Homestake, Newcrest Mining and WMC Resources, amongst hundreds of other mining, exploration and major contracting and services companies. MARCSTA; the Mining and Resources Contractors Safety Training Association (a pro-active not-for-profit self-help group of 24 major contracting companies) developed this generic safety induction. MARCSTA set out to find the æcommon groundÆ necessary to help address the evident safety problems and cost of re-training that were plaguing development of an internationally competitive and productive export industry. The incredible expansion of Australian mining during the decade fuelled a need for out-sourcing, resulting in much larger numbers of contractors on-site. At the same time, changes within Australian legislation, community expectations and the development of huge fly-in/fly-out operations and widespread skills shortages led to a rapid labour turnover and a higher paid workforce. Many Australian mining houses also ran international operations, particularly in South East Asia and head hunted people across the world. The skill levels fluctuated and fell at some local operations. Employers could no longer rely on systematic in-house training of permanent employees to improve safety and productivity as workers could and often did move on. Serious discrepancies in both quality and quantity of safety induction training and work practices occurred. Repetitive, boring and ineffective safety training became an embarrassing and costly burden for companies and workers alike. Then a spate of mining deaths sparked highly publicity, workforce concern and a demand for improvement from government, unions and corporate stakeholders. MARCSTA recognised it had to develop a high-quality safety-training program to satisfy the needs of all employers and be acceptable to others within the industry. This induction system had to be flexible enough to meet differences in legislation between states and industry sectors and be portable to enable cost and time savings for the new transient workforce. Changes in the last two years as a result of evaluating and incorporating various Taskforce inquiries into underground mining fatalities later led to the development of the MARCSTA Underground Safety Induction. This logical development added to the run away success of MARCSTAÆs General Safety Induction and was seen to be essential for many surface mines that were planning to develop underground operations. There are many lessons that MARCSTA learnt during its development that Pacific and South East Asian mining operations can benefit from. The most important of these are the support of stakeholders within industry and the recognition of higher safety and health expectations from workers and government. This goes hand-in-hand with the productivity and return on investment expectations of companies and their shareholders.

Jan 1, 1999

By R. Farrar

Protective canopies for conventional electric face equipment, including shuttle cars, operating in low coal (less than 48 inches) were designed, fabricated, installed and evaluated on in-mine machines engaged in regular coal mining operations. This work was performed under contract to the U.S. Bureau of Mines, Pittsburgh Mining and Safety Research Center. The canopies will support a vertical load of 18,000 pounds and provide protection against both roof falls and contact with the mine rib. Canopy configurations were established based on human engineering studies, full scale canopy mockups, and in-mine observation and consultation with mine and equipment manufacturing personnel. Overall height of each canopy is hydraulically adjustable between a minimum of 32 inches and a maximum of 40 inches. Canopy tops are open framework, welded structures, covered with expanded metal mesh. Structural members are 1 3/4-inch or 2-inch square tubing of AISI 413ON and ASTM A500 material, respectively. The canopy tops are typically supported by an understructure and upright post arrangement that is either integrated into the current operator platform or attached to the machine frame. The four upright corner posts house the hydraulic actuators. Canopy tops are elevated horizontally. Canopies are welded or bolted to the existing machines. Installation is accomplished with a minimal amount of interface modifications. No major machine design changes are required. Canopies were trial installed and load tested at the manufacturer's facility prior to installation on the in-mine machines. Canopies were installed on a Joy 14BU10 Loader, 16RB-3AH Cutter, and two 21SC Shuttle Cars, and a Galis 300 Roof Drill and 460-S Face Drill. Canopy installations were evaluated in the Jewell Ridge Coal Company No. 12 and Big Creek Tiller Mines. Operational time accumulated on the installations during evaluation ranged from 1 week to 14 weeks of two-shift operation. All five canopy designs, manufacture, and test were successfully accomplished. The five canopies met all safety requirements. Three of the five canopies were deemed to be completely successful from an operator's point of view. That is, mine management as well as the machine operator found that the canopies did not impede the operation of the machines to function with the same efficiency as before the installation of the canopies. The loader canopy, in fact, appeared to have provided a mole efficient operation of the loader by providing added safety to the operator from rib contact thus allowing him to concentrate more fully on the loading function. Operational problems were encountered with the shuttle car and the roof drill. The shuttle car canopy obstructed visibility to an objectionable amount and the roof drill canopy impeded maneuverability of the machine, more than doubling the roof bolting time.

Jan 1, 2012

By Randy N. Powell

The Pipeline gold ore body was discovered in Lander County, NV in March 1991. Construction of the new mine and mill did not start until early March 1996. The $289-million project was placed on a fast-track development schedule upon completion of permitting and corporate approval. The mine and mill were commissioned 11 months after the start of construction and the project ended up $40 million under budget. Project design and construction management were provided by Placer Dome Project Development Division (PDD). History The Cortez Joint Venture has operated in northeast Lander County since the late 1960s. The business structure is comprised of 60% Placer Dome and 40%Kennecott Exploration. Throughout the years, production has been from several small open-pit deposits— Cortez, Horse Canyon, Gold Acres and now Pipeline.

Jan 1, 1999

By E. O. Wagner, A. W. Koth, V. F. Parry, J. B. Goodman, D. C. Gernies

"INTRODUCTION A commercial-scale pilot plant for gasification of lignite was completed by the Bureau of Mines at Grand Forks, N. Dak., early in 1945 as an extension of work on, gasification of low-rank coals initiated in a smaller pilot plant at Golden, Colo., during 1943. The development work on this plant was part of a program to make reducing gases from lignite for beneficiation of low-grade iron ores. The background of this project has been described in a previous report. 6/ The present report describes the major features of the large pilot plant, a record of experimental operating data during five runs totaling about 1,800 hours, .and results of experimental work on the small pilot plant at Golden during 1945.This project has created considerable interest because heretofore there has been little success in several attempts to gasify American lignites.Furthermore, the methed employed is a departure from conventional processes. Natural lignite is fed continuously into an externally heated annular retort and is converted into water gas by heat conducted through alloy metal walls. Because of the high thermal conductivity of metal, the rate of gasification is several times greater than can be obtained when employing refractory walls. The process has been developed to a part that leaves one major question unanswered. - ""How long will the alloy last under practical operating conditions?"" - and this question has aroussed the interest of the Coal Division of the Bureau of Mines in this new development.Owing to the high reactivity of the lower-rank fuels, the water-gas reactions proceed rapidly at medium temperatures of 1,650°F. to 1,800°F. These temperatures can be attained in a reaction zone heated by external means when the temperature of the retort does not exceed 1,900°F. while transferring from 6,000 to 7,000 B.t.u. per hour per square foot. Such rates are several times greater than can be attained through refractory walls as employed in the Didier-Bubaig 7/ and the Ahrens processes. 7/ Therefore, the investment cost of the gas generator per unit of capacity will be considerably lower for the higher-capacity process. However, the maintenance cost of metal vessels will be higher than that of refractory retorts, and this emphasizes the importance of large-scale operation to determine the life of an alloy retort under practical operating. conditions."

Sep 1, 1947

By W. H. Ryback

When a fire or explosion occurs in an underground coal mine, the atmosphere guickly becomes irrespirable. Highly irritant smoke and toxic levels of carbon monoxide and dioxide are produced, and consumption of oxygen by the fire or blast can reduce its concentration below that needed to support life. Work parties entering such a hazardous atmosphere for rescue or recovery operations are required to use, as their primary respiratory protection, a fully self-contained breathing apparatus of at least two hours duration. Apparatus used in this role has primarily been of the closed circuit rebreather type, using pressurized oxygen storage and chemical removal of expired carbon dioxide. Typically, commercial self-contained breathing devices for mine rescue have been heavy, bulky, and uncomfortable to use. The McCaa apparatus, long the industry standard, represented the best art available when it was First designed in 1926. It weighs 41 Ibs., protrudes about six inches above shoulder height, and provides breathing gas at temperatures up to 120° F. More recent designs, such as the Drager BG174A and Scott Rescue-Pak, using modern light weight materials and fabrication techniques have improved on all parameters of the McCaa to some extent. It was the intent of the Bureau of Mines, acting under the authority of the Coal Mine Health and Safety Act of 1969, to fund the development of a new self-contained breathing apparatus which would incorporate the best available technology and serve as a benchmark for future commercial designs, as the Bureau-sponsored McCaa had 45 years previously.

Jan 1, 1974

By Juan Marcelo Rojas Arango

O refino de grão da estrutura bruta de solidificação da liga Cu-8%Sn com a adição de Zr foi estudado através da análise térmica e da observação da macro e microestrutura. Os resultados macro e microestruturais mostram que a adição de Zr causa a diminuição do tamanho médio de grão em até 90%. A diminuição do super-resfriamento da recalescência e do período da recalescência, medidos nas curvas de resfriamento, estão correlacionados com a diminuição do tamanho médio de grão causado pela crescente adição de Zr, indicando uma possibilidade de controle do tamanho de grão a partir da análise térmica. A análise da microestrutura das amostras em conjunto com a técnica de extração de precipitados por réplica mostra evidências de que o mecanismo de inoculação é a nucleação heterogênea da fase Cu-a sobre as partículas de ZrC formadas no banho líquido a partir das adições de Zr.

Aug 17, 2017

By Max W. Ball

THE world's largest known oil deposit lies in northern Alberta. In fact, according to government estimates, the famous so-called 'tar sands' of the Athabaska region contain several times as much oil as all the other proved reserves of the world. S. C. Ells, of the Department of Mines and Resources, who has been the Dominion Government's authority on the oil sands since 1913, has estimated the minimum content of the deposits at 100 billion barrels(!). C. P. Bowie, of the U.S. Bureau of Mines, has published an estimate of 250 billion barrels(2). ?In comparison, the latest authoritative estimate of the proved oil-field reserves of the world is less than 35 billion barrels(3). Out of this tremendous total, perhaps 500 million barrels are commercially available at present-day costs and prices; the remainder must be considered a latent reserve to be used when development costs are materially lower and petroleum prices materially higher than they now are. Mean-while, the 500-million-barrel portion presently available contains more oil than has been found in all the rest of Canada, and constitutes one of Canada's great mineral resources. Although these deposits have been known to white men since 1788, when Peter Pond, the explorer, found the Indians stewing the oil out of the sand and mixing it with spruce pitch to caulk their canoes, they are only now coming into commercial production. The purpose of the present paper is to describe the deposits, their oil content, their present development, and the possibilities that seem to lie immediately ahead. For the sake of completeness and clarity, the writer has not hesitated to use or to paraphrase material that he has previously published elsewhere in discussing various aspects of the oil sands.

Jan 1, 1941

By H. David Swain

On Bougainville Island in Papua New Guinea, Bougainville Copper Ltd. (BCL) has successfully applied electronic data processing (EDP) techniques to pit operations and mine planning. Though the EDP program is not complete, BCL has realized significant improvements in short and long range mine planning, and equipment and manpower utilization. About 80% of BCL's 4000 employees are Papua New Guinea nationals, and most have little education or training. The operational characteristics of the computer equipment, however, have been quickly adapted by users with low educational standards.

Jan 3, 1979

By Van Sint JanM., M. Prudencio

ABSTRACT We report the results of a model-testing program to evaluate the strength characteristics of non-persistent joints. We describe the conditions under which new tensile cracks generate and propagate to connect existing joints so that the rock mass becomes fractured into several blocks, leading to a low strength. The strength of some models was equal to that along a single joint through the full sample length. In models with two joint sets, failure took place along a composite plane, partly sliding along a discontinuous joint and shearing through the intervening intact block of rock, or else by rotation and sliding of the blocks. This last failure mode could also lead to very low model strength. ZUSAMMENFASSUNG Dieser Bericht beschreibt die Ergebnisse von Versuchen mit Modellfelsmassen um den Einfluâ von unterbrochenen Rissen in ihrer Widerstandsfähigkeit zu untersuchen. Es werden die Umstände beschrieben unter denen neue Zugrisse entstehen, sich verbreiten, sich mit bestehenden Rissen verbinden und die Felsmasse in mehrere Felsblöcke zerlegen und zu einer kleinen Widerstandsfestigkeit führen. Der Widerstand einiger Versuchskörper entsprach der Festigkeit eines Risses der die ganze Länge des Versuchskörpers überquert.Versuchkörper mit zwei Rißfamilien versagten unter einer zusammegesetzten Ebene, zum Teil mit Verschiebungen nach unterbrochenen Rißebenen die sich durch Schnittversagen intakter Felsblöcke verbinden, und zum Teil durch Drehungen und Verschiebungen einzelner Felsblöcke. Die letzte Versagunsart kann zu einer stark verminderten Widerstansfähigkeit führen. RÉSUMÉ Nous présentons les résultats de quelques essais fait sur des modèles évaluant les caractéristiques de résistance des fractures discontinues. Nous décrivons les conditions sous lesquelles des nouvelles fissures de traction peuvent s’engendrer et se propager pour faire la connection avec des fractures existantes, de façon que le rocher se fracture en plusieurs blocs, menant à une résistance réduite. La résistance de quelques modèles fut égale a celle d’une fracture traversant toute la longueur du modèle. Pour les modèles ayant deux ensembles de fractures, la rupture a eu lieu sur une surface mixte, causée d’une part, par le glissement sur une fracture discontinue et d’autre part, par la rupture à travers le pont de matériel intact; ou bien par rotation et glissement des blocs. Cette dernière façon de rupture peut aussi aboutir à une très faible résistance des modèles.

Jan 1, 2003

By B. Genc

Safety in South African mines is a subject of significant interest, since many mining companies are experiencing production deficits due to safety-related stoppages. In this paper, safety data from the South African platinum mining sector is analysed for the period 2006 to 2010. The data was obtained from company annual reports as well as the Department of Mineral Resources, and analysis in the study is limited to injury and fatality data only. The overall safety performances of companies in the sector are compared, and opportunities for benchmarking and recognising potential sources of best practice amongst platinum miners are identified. Improving safety usually incurs a cost, and mining companies are particularly conscious of the importance of controlling costs. However, cost considerations often deal only with direct costs, and it has been shown that indirect costs are usually far more significant. Therefore, a greater safety spend will usually result in the creation of value for the mine since it will reduce the indirect costs associated with accidents. The results of some recent research in this area are presented. In this light, where available, the financial performances of mining companies in the sector, obtained from published annual results, are included in the benchmarking exercise to determine whether there is any correlation with safety performance.

Jan 1, 2012

By V. Lakshmanan, Dan Mackie, J. Melnbardis

"Crystalline Flake Graphite is a strategic mineral. Since 1954 nearly all North American consumption has been imported from offshore. The Bouthillier Project in Quebec, Canada, is Orrwell Energy's bid to enter the market, with plans to begin production of a 500 TPD operation in 1984.Milling of flake graphite is considered easy, yet more problems have been encountered in flowsheet and plant design than in most other minerals. A fresh approach to existing technology was taken, giving results that are highly satisfactory. The key to graphite liberation without flake deterioration is found to be in autogeneous grinding. In addition to producing marketable coarse graphite by such autogeneous grinding, flotation and tabling, super purity fines can be produced using repeated regrinding, elutriation and flotation. This paper discusses the design of a 500 TPD plant based upon the results obtained from bench and pilot plant studies. INTROOUCTIONWhen the Black Oonald mine at Calabogie Ontario ceased production in 1954 nearly all North American crystalline flake graphite had to be imported from offshore. Orebodies in the United States were too small or too low in grade to be exploited economically.The Houthillier Township near Mont Laurier in Quebec (Figure 1) was a known graphite-bearing area The Orrwell property in that area was delineated in 1957 Some test work including minor footage of diamond drilling was carried out by Italia Copper and the MHM Syndicate prior to 1981 when Orrwell acquired the property"

Jan 1, 1984

By Hani Henein

Recent innovations in atomization of molten metals have occurred in the area of single fluid atomization. Impulse Atomization (IA), one of the single fluid techniques, provides unique capabilities to study different regimes of atomization in a controlled environment. By changing processing variables, a mono-dispersed distribution of droplets above one millimeter in diameter can be produced. This is accomplished through proper characterization of the forces influencing the process and in particular the flow of melt through the orifice. This paper will discuss the approach and illustrate results with molten aluminum and cobalt.

Jan 1, 2006