Search Documents

By H. W. McQuaid, E. W. Ehn

It is usually assumed that chemical specifications are sufficient for steel to be used for case carburizing, and if the steel analyzes within the ordinary limits specified for steel for this purpose, no difficulty traceable to the steel used should be encountered in obtaining satisfactory results in the case carburizing and hardening. Much work has been done to determine the effect of various alloying elements on the rate of carbon penetration, etc. but, to our knowledge, little if anything has been published in regard to the effeet of the quality of the steel on the final results in the hardening of case-carburized steel parts. The writers believe that the structure of the case both before and after quenching is greatly affected by the actual condition of the steel itself as made, and that for good results in the case-carburizing and hardening departments, the steel should be of the best possible quality as regards non-metallic impurities. It is the purpose of this paper to prove that the presence of excess dissolved oxides in the steel, as made in the melting furnace, affects permanently the results obtained in carburizing and hardening and that it is possible that the presence of dissolved oxide call result in total unfit-ness of low-carbon steel for case hardening purposes. When races and rolls for roller bearings are made from a low-carbon steel, case carburized and hardened, it is of primary importance that the results of this treatment be of the highest quality. It is necessary, therefore, that in the case-carburizing work each detail be rigorously checked to avoid any defects which would cause the loss of much time and material. The case carburizing with which this paper deals was done in under-fired oil furnaces. The temperature of each furnace is controlled by means of a platinum platinum-rhodium thermocouple, in connection with a potentiometer indicator and potentiometer recorder. The temperature of each furnace is registered every 15 min. by an operator, who is continually checked by the automatic recorders.

Jan 1, 1922

By Irajá Bernardino Ribeiro Juniorr

O presente trabalho tem por objetivo apresentar alguns exemplos de aplicações na Indústria Siderúrgica e de Mineração (Prensa de Rolos e Torre de Resfriamento) mostrando que com o emprego de uma confiável metodologia para determinação dos benefícios energéticos é possível a implantação das medidas de conservação de energia em sistemas de força motriz instalados nestas indústrias com o simples uso de Lubrificantes Sintéticos Especiais em substituição ao largo emprego de óleos minerais. Esta solução também proporciona ganhos energéticos e financeiros expressivos e mais atrativos do que as já consagradas soluções de eficiência energética como troca de lâmpadas e /ou motores de alto rendimento. Além do mais, a troca de lubrificante já é rotina implementada nas indústrias e seus profissionais da área de manutenção, não sendo preciso treinamento adicional para implementação, tornando esta ação com o propósito de economizar energia simples e fácil de ser implementada. Este trabalho é uma parte dos resultados do projeto inovador desenvolvido pela Klüber Lubrication desde 2010, onde o principal objetivo é disponibilizar aos usuários de sua linha de produtos este recurso, internacionalmente reconhecido, de Medição & Verificação para a comprovação de ganhos de energia em prensas de rolos com alcance de redução de cerca de 10% de consumo de energia.

Aug 17, 2017

By Rodrigo de Oliveira Pezzin

Devido ao fato que a exigência por menores teores de enxofre em alguns tipos de aços, torna-se interessante investigar a eficiência na dessulfuração dos materiais já conhecidos com matérias primas alternativas. Duas dessas novas matérias primas que podem ser utilizadas no processo de dessulfuração são o resíduo de mármore e a sodalita. Desta forma, o presente trabalho tem como objetivo avaliar a eficiência de dessulfuração em ferro-gusa por misturas contendo resíduo de mármore, sodalita e agentes dessulfurantes convencionalmente utilizados. Os testes foram realizados a 1400°C, em uma atmosfera inerte (Ar) com agitação constante. Os testes experimentais mostraram que 50 a 90% da dessulfuração ocorreu em até 15 minutos. As misturas contendo fluorita foram os que apresentaram maior eficiência de dessulfuração. A adição de sodalita ocasionou uma queda na eficiência de dessulfuração.

Aug 17, 2017

By M. Mohammadijoo, J. B. Wiskel, D. G. Ivey, S. Kenny, H. Henein

Cold-wire tandem submerged arc welding (CWTSAW) has recently been developed as a novel welding technique to replace the conventional tandem submerged arc welding (TSAW) process and improve the productivity of pipeline manufacturing. The process involves two electrodes with arcs and one electrically cold electrode. Since heat-input of the welding process is a key factor affecting the properties of the weld metal (WM) and the heat-affected zone (HAZ), and the additional cold-wire affects the heat introduced to the weldment, it is of interest to investigate property and geometry changes in the WM and HAZ when a cold-wire is added to the welding process. In the current research, the CWTSAW process is investigated and optimized by correlating the main welding parameters with the micro-hardness of the WM and HAZ and the geometry of the weld, i.e., the bead width (BW), penetration depth (PD), reinforcement area (RA) and coarse grained heat-affected zone (CGHAZ) area. Three statistical and mathematical methods are employed to optimize the CWTSAW process in terms of the mechanical properties and WM and HAZ geometry of a typical microalloyed steel used for pipeline manufacturing.

Jan 1, 2015

By Gabriela Moreira Lana

A radiação solar apresenta uma enorme variedade de aplicações de engenharia, dentre elas, a conversão em energia térmica em concentradores solares. Os tubos absorvedores dos concentradores solares podem ser recobertos por cromo negro, com o objetivo de otimizar a absorção energética e a durabilidade. Esse trabalho é parte de um estudo complexo sobre esse tipo de recobrimento. Foram desenvolvidos filmes de cromo negro por eletrodeposição sobre aço inoxidável AISI 304 e tratados termicamente a 600°C por 2 horas. Os filmes foram caracterizados antes e depois do tratamento térmico, utilizando-se microscopia eletrônica de varredura (MEV), espectroscopia de energia dispersiva (EDS) e difração de raios X a baixo ângulo de incidência (GAXRD). Além do cromo, observou-se deposição de cobalto e elementos residuais do banho eletrolítico. O estudo da estrutura cristalina mostrou formação de óxidos após tratamento térmico. Microestruturalmente, foram observados filmes com estrutura lamelar ou nodular. O estudo permitiu sugerir modificações do banho eletrolítico, do substrato e métodos adicionais de caracterização.

Aug 17, 2017

By Eduardo Christo Saltoratto

Foram realizados tratamentos térmicos de têmpera e revenimento para aumentar a tenacidade do material, aço NM87 designação 1045, uma vez que ele apresentava, no estado inicial, baixa absorção de energia. Com o material mais tenaz foi obtida uma melhor faixa de energia para cálculo das incertezas. Foram feitos corpos de prova com variações nas medidas laterais, de comprimento e profundidade do entalhe e ensaiados na temperatura ambiente para determinação das incertezas do tipo A e B. Com as incertezas determinadas pelos métodos estatísticos e não estatísticos, foram feitos ensaios, variando-se a temperatura, para obter dados de ductilidade (energia absorvida, expansão lateral e percentual de área dúctil) em relação a temperatura e com esses dados determinar-se a temperatura de transição dúctil – frágil e sua incerteza.

Aug 17, 2017

By T. Skinner, M. Sahebkar

"In recent years, the mining industry has been inundated with new technologies and software systems to aid in productivity improvement. Accompanying this increased level of technology and computer systems has been the exponential growth in data sources and sinks for all aspects of a mining operation. This rapid growth in data and technology has evolved through vendor “push” approaches and user “pull” scenarios, the result of which has been that currently, no standards exist defining how data from new technology should be accessed and transferred from surface mining equipment and systems. Consequently, many incremental benefits of the systems have not been realized. This paper will present a discussion of this important issue and introduce a new committee formed to address standards to assist the industry in making effective use of current and future technology. Potential benefits accruing from the development of these standards will be illustrated through the use of a case study at Fording Coal Limited. IntroductionThe mining industry is currently faced with a rapid evolution in the computing-based systems capabilities of mobile production equipment. At the same time, there is a trend toward the introduction of even larger machines, with novel designs or incorporation of new technologies within existing designs. Computing and control technology will be required to operate and acquire knowledge about equipment operation, utilization, and performance. Such knowledge has the potential to lead to enhanced equipment design, more appropriate equipment selection, and optimized equipment performance. The equipment systems will be required to be integrated with mine production monitoring systems, maintenance management software, and a wealth of other information systems to provide a complete understanding of the effects of various factors such as maintenance, equipment design and production on economics (Roman and Daneshmend, 2001). This will lead to a better understanding and implementation of the opportunities to enhance the performance of the mine through interaction of the mine operations."

Jan 1, 2003

Two key strategies for a new generation of mining are developing domestic raw material production and doing so in an environmentally responsible way, according to presenters at the 83rd annual meeting of the SME Minnesota Section in Duluth (the 71st annual University of Minnesota Mining Symposium). From technical sessions detailing how to build com-munity support, to a short course on international perspectives in iron ore mining and processing, the two-day meeting emphasized the potential of Minnesota state deposits and the importance of maintaining productive community relations both locally and globally. The meeting of more than 300 mining industry professionals began on April 20 with a traditional convocation celebrating the values of northern Minnesota. The accompanying tradeshow, with a record 131 booths, showed the speed and vigor of the economic rebound. Keynote speaker Scott Anderson, vice president and senior economist at Wells Fargo, stated the prevailing mood of the conference: ?Wow, what a difference a year makes.? With metal prices and sales up and heading higher, he said, it was clear that the production-centered economic recovery is reaching the mining and the minerals industry. However, Anderson sounded a few notes of caution. Serious threats to economic stability remain, including the burgeoning national de?cit, high unemployment and the still out-of-control foreclosure crisis. Overall, he predicted a below-average recovery and stressed the importance of developing a long-term business strategy.

Jul 1, 2010

By D. F. Malan

Considerable practical knowledge and effective use of empirical evidence is required in the design of tunnel support systems. In many instances, it is unclear how individual support elements interact with fractured rock and which elements of the support system are critical in controlling and containing the movement of material proximate to the excavation. The present paper outlines a displacement discontinuity approach that allows the coupling of surface constraints, in the form of liner or mesh material, to an explicit representation of time-dependent rock discontinuity creep movements. The method is illustrated for a simple square-shaped tunnel profile in which the fracture zone is mobilized by an imposed stress field. A crucial aspect of the model is the computational treatment of the coupling between the liner material and there presentation of the fractured rock mass. This allows the response of the liner material to be assessed quantitatively in terms of the possible reduction of movement in the rock mass. The importance of installing the liner timeously after the excavation is formed is illustrated in a specific example. A number of computational difficulties in simulating liner-rock interaction mechanisms are identified.

Jan 1, 2008

By Marcos Danilo Monteiro

O final do século XX foi marcado por um grande avanço tecnológico em sistemas automatizados com variadas aplicações, dando destaque ao campo da robótica que desde então busca otimizar cada vez mais os processos industriais, eliminado a mão-de-obra humana em segmentos onde sua presença antes era indispensável. O aumento na qualidade do produto, a relação custo-benefício e dentre outras melhorias que a robótica trouxe a uma linha de produção industrial, justificam a procura por parte das grandes empresas em procurar investir na inserção desta tecnologia ou no melhoramento dela em sua cadeia produtiva. Este trabalho teve como principal objetivo demonstrar a aplicação da tecnologia robótica na indústria, em proporções reduzidas e fins didáticos, com a integração de um sistema de controle e automação representado pela plataforma Arduino que atua no controle de coordenadas de um braço robótico em atividades de carregamento e paletização de cargas.

Jul 30, 2018

By Fernando de Souza Costa

Nos últimos anos a indústria automotiva vem conseguindo avançar de forma contínua em relação ao controle da emissão de CO2 e no tocante à segurança veicular. O aumento da utilização de aços de alta resistência mecânica se constitui num dos principais sustentáculos destas melhorias. Além disso, na manufatura de certas peças, em especial as de geometria complexa, é fator crítico de sucesso a capacidade do material em absorver intensas deformações localizadas, tipicamente encontradas em operações de expansão de furo. O aço desenvolvido pela Usiminas é um produto laminado a frio, com revestimento eletrogalvanizado, da classe de 600 MPa de limite de resistência, com boas propriedades de flangeamento de bordas e de alongamento em tração. Neste trabalho, é apresentado o desenvolvimento deste aço. São descritas as suas principais características e os resultados de sua aplicação em uma peça de geometria complexa.

Aug 17, 2017

By Jéssica Dornelas Silva

Diferentes mecanismos podem atuar e governar a deformação plástica de uma liga metálica. Estes mecanismos são fortemente dependentes de características como composição química, estrutura cristalina e energia de falha de empilhamento. Com o objetivo de se avaliar o comportamento do aço inoxidável duplex UNS S32304 quando submetido a esforços trativos e considerando a importância desta informação durante a conformação mecânica, este trabalho estudou a influência da taxa de deformação sobre as principais propriedades mecânicas medidas no ensaio de tração. Para a realização deste estudo, corpos de prova de tração foram usinados a partir de chapas do referido aço laminado a frio com espessura final de 2,5mm. Cada conjunto de 3 corpos de prova foi submetido às taxas de deformação de 7x10-4 s-1, 7x10-3 s-1 e 4x10-2 s-1. Por meio da análise dos resultados, observou-se uma diminuição na ductilidade e um aumento no limite de escoamento com o aumento da taxa de deformação. Entretanto, o limite de resistência não variou de forma significativa nas diferentes taxas estudadas.

Aug 17, 2017

By Tiago Seixas Bittencout

No cenário econômico mundial atual, cada vez mais as indústrias têm voltado sua atenção para o reaproveitamento de materiais gerados como consequência das ações operacionais, tanto como forma de reduzir custos, como também no caráter de sustentabilidade do negócio. Em uma operação de refino primário em aciaria elétrica, onde o produto é o aço líquido, o antes considerado resido, mas agora denominado de coproduto, a escória, passa atuar diretamente no custo final do produto quando esta é processada, e passa a compor a carga fria usada no processo de elaboração do aço. Neste sentido, o estudo deste material se faz necessário para a compreensão de qual será o seu comportamento junto aos processos e quais vantagens e desvantagens da sua aplicação. Neste trabalho, foram feitas as caracterizações de sucatas provenientes de reaproveitamento de escórias produzidas em Forno Elétrico a Arco e em conversor LD, bem como seu impacto no refino primário, como parte integrante da carga fria no FEA.

Aug 17, 2017

By James Rowland, Isaac Zlochower, Richard Mainiero, Michael Sapko

The National Institute for Occupational Safety and Health (NIOSH) carried out exploratory laboratoryscale studies to identify factors that may contribute to nitrogen oxides (NOx) production associated with non-ideal detonation of blasting agents. Explosive admixture with drill cuttings, loss of fuel oil in ammonium nitrate and fuel oil (ANFO) from wicking, ammonium nitrate dissolution with water, degree of explosive confinement, ANFO density, and critical diameter were identified as contributing factors to increased NOx production under the laboratory test conditions. Experiments were also conducted to examine the effectiveness of various additives in reducing the NOx production from ANFO, emulsion, and ANFO/emulsion blends. Aluminum powder, coal dust, urea, and excess fuel oil in ANFO formulations were tested and were found to reduce both the nitric oxide (NO) and nitrogen dioxide (NO2) production. Fumes measurements were obtained in the NIOSH underground closed chamber from the detonation of 4.5-kg (10 lbs) charges in schedule 80 seamless steel pipe and from detonations in light weight galvanized steel stove pipe. Some exploratory tests were also conducted with 0.8-kg (1.8 lbs) charges of pulverized ANFO initiated with 0.08-kg (0.18 lbs), 50/50 (Pentolite) boosters (in the NIOSH 12-ft (3.7-m) diameter steel sphere) to measure the degree of fumes production associated with post-detonation oxidation. Ammonium nitrate, emulsion and Pentolite boosters were also detonated in an oxygen-poor environment.

Jan 1, 2002

By Donald E. Stump

Subsidence from underground coal mining alters surface water discharge and availability. The magnitude and areal extent of these impacts are dependent on many factors, including the amount of subsidence, topography, geology, climate, surface water - ground water interactions, and fractures in the overburden. These alterations may have positive and/or negative impacts. One of the most significant surface water impacts occurred in July 1957 near West Pittston, Pennsylvania. Subsidence in the Knox Mine under the Coxton Yards of the Lehigh Valley Railroad allowed pan of the discharge in the Susquehanna River to flow into the mine and create a crater 200 feet in diameter and 300 feet deep. Fourteen railroad gondola cars fell into the hole which was eventually filled with rock, sand, and gravel. Other surface water impacts from subsidence may include the loss of water to the ground water system, the gaining of water from the ground water system, the creation of flooded subsidence troughs, the increasing of impoundment storage capacity, the relocation of water sources (springs), and the alteration of surface drainage patterns.

Jan 1, 1986

By P Corbett, P Sheffield

Centennial Coal operates the Springvale longwall mining operation which extracts coal beneath the Newnes Plateau in the Western Coalfields of New South Wales. Springvale, and the neighbouring Angus Place mine, have a history of difficult geotechnical conditions where combinations of a relatively high stress regime and weak, laminated roof and extensive geological faulting has led to numerous roof failures throughout the mine’s life. Following development, the mines underground roadways can experience high levels of roof movement which may lead to roof falls. Multipoint wire extensometers are extensively used throughout the mine for roadway condition monitoring, and to reactively drive remedial strata support through trigger action response plans (TARPs).As a result of the use of high-density extensometer monitoring over a long period, the mines have an extensive archive of legacy data. Data processing has evolved over time in order to accommodate the increasing data volume, including direct data entry from the recently introduced hard-wired real-time monitoring instruments. It is likely that telemetric real-time instruments will be introduced in the future, which will cause another step change in data management requirements. This paper discusses the transition to and evolution of relational database management systems for extensometer and associated data.This paper also presents case studies of the use of a new software tool for reprocessing legacy data to enable time-scaled visualisation of monitoring data in the context of longwall and development face positions and installed strata support. The software can be used proactively in the identification of geotechnical risk factors and their interaction with the mining process to allow a more robust geotechnical hazard process. It interfaces directly with the widely used ExtoChart database software and can be presented with scale drawings of geological and geotechnical data to allow correlation of monitoring data results with risk factors.CITATION:Corbett, P and Sheffield, P, 2015. The use of high-intensity monitoring data to better characterise geotechnical properties of a non-homogeneous rock mass, in Proceedings Third International Future Mining Conference, pp 145–158 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

By Bernardo Martins Braga

O desgaseificador RH é um reator de refino secundário bem estabelecido. Nesse equipamento, gás inerte é usado para promover a circulação de aço entre a panela de aciaria e uma câmara de vácuo. A predição correta da dispersão de gás na perna de subida do RH é importante para a modelagem confiável do processo. O presente trabalho estudou a penetração de gás na perna de subida do RH por meio de modelos físico e matemático. No estudo, foram considerados apenas um ou dois bicos injetores e vazões de gás, por bico, entre 5l/min e 50l/min. Para as condições com um bico injetor, os resultados das duas abordagens mostraram boa concordância qualitativa. Já para as condições com dois bicos injetores, a concordância só foi satisfatória para vazões de até 30l/min por bico. Adicionalmente, os resultados obtidos indicaram que o problema de penetração de gás em modelos matemáticos de desgaseificador RH identificado na literatura está relacionado com erros numéricos e não com falhas na modelagem da física do problema.

Aug 17, 2017

By Fernando de Oliveira Boechat

Dentre as etapas de pelotização de minério de ferro, a fase de mistura tem grande importância devido ser responsável por dar homogeneidade a aos insumos e minério que serão processados nas etapas seguintes. Desta forma ela ajuda a garantir a boa formação das pelotas verdes e seu posterior endurecimento na etapa de queima. No desenvolvimento de misturadores, o auxílio de ferramentas de simulação são uteis para o correto dimensionamento destes equipamentos. Nos últimos anos a utilização do método dos elementos discretos (DEM) tem sido implementada para este fim e por isto vários cuidados têm sido tomados para ter-se resultados compatíveis com o comportamento real das partículas. Entre os fatores que podem inviabilizar o uso do método dos elementos discretos, o tempo e capacidade de processamento computacional tem sido um dos mais impactantes. Assim, este trabalho foi desenvolvido de forma a avaliar a influência do tamanho das partículas no resultado de capacidade de mistura de um misturador horizontal. Para isto, foi feito o escalonamento do modelo de um misturador e testado dois tamanhos de partícula avaliando o comportamento da mistura ao longo do tempo e o seu índice de mistura Lacey. Como resultado, pode-se verificar que o tamanho da partícula tem influência direta no resultado da simulação e que cuidados devem ser tomados no escalonamento destas para que haja compatibilidade entre as simulações e o comportamento real do sistema.

Aug 17, 2017

By Eric Lindquist, John Compagnone, Gabriel Carvajal

"Condon-Johnson & Associates, Inc. (CJA) with the assistance of design consultant, Brierley Associates, designed and installed a water tight shoring system utilizing several ground improvement techniques jointly. Prior to the installation of the shoring system, a test program consisting of the installation and testing of 7 jet grout columns; 1 soil mix panel; 7 soil anchors and 3 tie downs was performed to verify design assumptions. State-of-the-art quality control measures were employed throughout the project.The shoring system consisted of:•,Deep Soil Mixing (DSM) wall utilizing triple axis tooling to install overlapping columns along the perimeter of the proposed excavation to a treatment depth of 54 feet.•,Installation of steel piles in DSM to provide rigidity to the wall.•,Installation of a jet grout bottom seal, installed from surface to a depth of 58 feet below existing grade.•,Installation of 153 soil anchors, 1-1/4” diameter and 47’-6” length, to tie the jet grout bottom seal to the native soil below to resist hydrostatic uplift, installed from existing grade to a depth of 91 feet.•,Installation of walers and pipe struts for internal bracing•,Installation and stressing of 117 tie downs, 1” diameter and 16 ft length, to tie the pump station mat slab to the jet grout bottom seal, installed from inside the excavated pit.Subsurface conditions at the site consist of uncontrolled fill materials to a depth of 20 feet comprised of sandy silt and clayey sand. The native soils underlying the fill generally consist of soft and compressible lean clay and silt with varying amounts of sands to a depth ranging from approximately 44 to 54 feet below ground surface, which in turn are underlain by dense to very dense silty sand. The groundwater elevation at the site is approximately 8 feet below ground surface.This paper covers the design aspects, construction, and quality control measures undertaken by the geotechnical contractor, with supporting figures.INTRODUCTIONThe owner, County Sanitation District No. 2 of Los Angeles County, designed upgrades to their existing Long Beach Main Pumping Plant Facility. The upgrades consist of a new pump station that includes a reinforced concrete below-grade wet well and dry well, a two-story operations building, two 78-inch diameter pipe inlets, two 42-inch diameter discharge pipelines connecting the existing manifold, two pipe junction structures, two insert-type junction structures, and electrical transformers. This paper focuses on the excavation shoring for the new pump station. The original shoring design concept for the pump station excavation illustrated on the contract plans consisted of pressed in sheet piles, a jet grouted bottom seal with soil anchors, 2 levels of internal bracing, and tie-down anchors to resist hydraulic uplift forces on the buried pump station."

Jan 1, 2017

By H. G. Moulton

The increasing scale of mining operations over the past decade, particularly in connection with the exploitation of large bodies of comparatively low-grade copper ores, has made necessary the study of the behavior of rock under failure. When extractions of as high as 40,000 tons a day are reached in steam-shovel operations and as high as 20,000 tons per day in underground mining operations, it is evident that excavations soon become of such size that the behavior of the rock will often be dependent on fundamental principles applicable to more or less homogeneous materials under stress, rather than on weathering or local planes of weakness. In the ordinary rock excavations encountered in civil-engineering practice, such as excavations for subways, highways, railroads, etc., rock faces are not carried to depths sufficient to develop any pressures, or consequently any failures, except those due to loose masses resulting from local planes of weakness. When, however, orebodies whose tonnage is measured by hundreds of thousands are to be extracted by steam-shovel operations in open pits, it is necessary to determine if possible in advance the slopes that the sides of the pits will assume, for these slopes influence the shape of the excavations and thereby the amount of ore that may be extracted by the open-pit method. When large orebodies are mined underground at depths of 300 to 500 ft. (91 to 152 m.) by caving methods, the surface subsiding as the ore is withdrawn, it is necessary to determine in advance the outermost limits of fracture in the subsiding surface, for on the delineation of these limits depends the location of surface improvements, mills, smelters, etc. and also the location of development work, such as hoisting shafts, main haulage levels, and all other underground openings that must remain undisturbed during the period of ore extraction. Heretofore, in civil-engineering practice, it has been assumed that earth and rock behave differently in failure. For the calculation of earth pressures, formulas are used in which the assumption is made that earth banks fail by sliding along the slope determined by the frictional resistance of the material. The line of failure and the resulting pressure is held to be dependent on the angle of repose, which is different for varying

Jan 1, 1920