Search Documents

By C. Chongo, F. X. Paquot, C. Ngulube

"Over the last six years, the Kansanshi copper/gold mine has continued to process significant quantities of complex transitional mixed ores. The effect of the complex mineralogy on the flotation performance is depicted. Initially, ore treated came predominantly from accumulated stockpiles. In the ensuing years, ore treated shifted to primarily freshly mined ore that generally showed less tarnish with better float kinetics but with the downside of producing lower concentrate grades. A number of changes were made to improve the efficiency of the roughing circuit and quality of concentrate produced. These changes were as a result of initial mineralogical studies and laboratory float test work done and discussed at length in a previous paper. Salient among the adopted recommendations from previous work were increasing circuit capacity and modifying configuration to increase the residence time and the number of sulphidisation stages. These modifications were completed and commissioned in 2011. This, however, resulted in significantly low rougher concentrate grades and subsequently below-specification final concentrate product. This was primarily due to higher mass pulls resulting from the extended rougher bank with multiple concentrate discharge streams. This necessitated the need for an enlarged cleaning capability to offset this. The extra cleaning capacity came on-stream in 2014. Of note was the development of a recovery model, based on the strong correlation between the total copper and acid-soluble copper ratio, as a tool for monitoring plant performance. INTRODUCTION The Kansanshi mine, the largest copper mine in Africa, is 80% owned by Kansanshi Mining PLC, a First Quantum subsidiary. The remaining 20% is owned by the state through the parastatal ZCCM. The mine is located approximately 10 km north of the town of Solwezi and 180 km to the northwest of the Copperbelt town of Chingola. The mine has been in commercial operation since 2005. Prior to June 2009, Kansanshi mine treated only two ore types: oxide and sulphide. All transitional ores mined during the period leading up to 2009 were stockpiled. The treatment of the minerologically complex, transitional ores through a third train commenced in June 2009 but with numerous metallurgical challenges. This transitional ore (called mixed ores) could not be previously treated economically due to high gangue acid consumption (GAC) minerals association (making it unsuitable for the oxide float–leach circuit) and poor flotation response ruling out the conventional sulphide float circuit. The new novel circuit involved a conventional sulphide pre-float followed by flotation involving staged controlled potential sulphidisation (CPS)."

Jan 1, 2015

By R. M. Goldhoff, J. W. Spretnak, R. Speiser

IT has been observed by Grange and Garvey' that the homogenization of boron-treated steels could lead to complete elimination of the hardenability effect caused by boron. The experimental conditions leading to this conclusion involved the heating of steel specimens with and without boron at 2350°F for 24 hr. To prevent oxidation and decarburization, the specimens were encapsulated under vacuum in silica tubes. This observation of permanent deterioration of boron effect was noted in both a 0.63 pct plain carbon steel and a 0.25 pct C low alloy steel, both of which had been treated with ferroboron and homogenized at 2350°F for 24 hr. In another series of boron-treated steels which had been homogenized for shorter times, the effect was to reduce, but not completely eliminate, the boron effect. Under these circumstances, it was presumed that longer heating times would cause permanent deterioration of the boron effect in this series of steels also. Since the characteristic grain boundary constituent could not be formed in any of these steels after homogenization, it was concluded that possibly boron was being converted into an ineffective form through chemical combination resulting from prolonged heating at high temperatures. Assuming the validity of this observation, a series of experiments to establish the relationship between temperature of homogenization and kinetics of deterioration was contemplated. Initially an attempt was made to reproduce the results just described. For this purpose commercial lots of AISI 8640 and AISI 86B40 steels were used. The analyses of these steels appear in Table I. Hardenability evaluation was on the basis of the hardness of normalized sections. Grange and Garvey' pointed out that these steels are air hardening to some extent and such a technique can be used. For these tests the specimens were held for 20 min in a salt bath at 1600°F and then cooled in still air. Several evacuated silica capsules containing pairs of the test steels were made up and heated for 24 hr at 2350°F. A number of failures occurred among these capsules, but evaluation of the specimens successfully treated indicated a complete deterioration of the boron effect. However, examination of the surface of the treated specimens showed that some reaction, probably with the silica tube, had taken place, since none of the specimens was bright. One further test was made at 2350°F for 12 hr, using a pair of specimens wrapped in tantalum foil prior to encapsulation. These specimens appeared bright after treatment, and their hardenability evaluation showed that no deterioration had taken place. Since these steels are extremely sensitive to de-boronization at high temperatures and particularly at long times of holding, the experimental observations raised some doubt as to the real occurrence of the permanent deterioration effect. To resolve this question an experiment was undertaken in which the high temperature portion of the treatment was completed in vacuum. For this purpose a molybdenum wound resistance furnace capable of maintaining good vacuum was used. All the pertinent accessories to this furnace were machined from molybdenum stock in order to withstand the high temperature involved in the experiment. With this equipment a temperature of 2400 °F was obtained and held under a pressure of 5x10-" mm Hg for 24 hr. A specimen of each of the two test steels was suspended in the furnace and both were heated simultaneously. Temperature was measured with a standardized Pt—Pt-13 pct Rh thermocouple, whose millivoltage at 2400°F was extrapolated from the standardization equation, good up to 2200°F. The complete evaluation of these specimens is shown in Table 11. The hardness values attained by each steel after normalizing, both before and after the prolonged high temperature treatment, remain the same. A microscopic study of the decomposition products present in the microstructures of specimens at various points in the heat treatment correlated with the hardness values observed. It seems that no permanent loss of boron hardenability effect occurs, at least in these Grainal-treated steels, when deboronization is circumvented. Acknowledgments This work was conducted under the sponsorship of the Aeronautical Research Laboratory, Wright Air Development Center, under Contract No. AF 18(600)-94, and their support and permission to publish is gratefully acknowledged. A note of thanks is also extended to the Republic Steel Corp. for supplying the materials used in the work. References ' R. A. Grange and T. M. Garvey: Factors Affecting the Harden-ability of Boron Treated Steels. Tro.ns. ASM, 1946, vol. 37, p. 136.

Jan 1, 1957

"Australia’s largest rail freight network operator, the Australian Rail Track Corporation (ARTC), has selected GE Transportation’s Movement Planner solution as the key technology enabler for its Hunter Valley-focused network control optimization program.ARTC’s Newcastle-based network control, is the nerve center of Hunter Valley rail operations, where locally based train control professionals make thousands of decisions every day to safely support the annual movement of more than 24 kt/h (26,400 stph) of freight, and tens of thousands of coal, freight, grain and passenger trains each year.ARTC plans to transform its train control function by integrating and then building on Movement Planner, an advanced software solution by GE Transportation that provides real-time rail traffic planning and optimization to enable freight to move more efficiently. “The Hunter Valley rail network is one of the busiest and most complex in the country, supporting the largest coal export port in the world,” ARTC managing director and chief executive officer John Fullerton said.“As bulk freight demands grow, rail operators like ARTC and supply chains like the Hunter Valley coal network need to be creative in the way they respond so the Australian economy doesn’t miss out. That’s why we have conducted a worldwide search to find globally proven solutions that will improve our network productivity and efficiency,” Fullerton said.The Movement Planner solution considers multiple factors including train schedules, trafficcontrol systems and train movements relative to each other and then develops an optimized traffic plan for the trains throughout the network. Existing GE customers have benefited from increased visibility of network operations, higher velocity, less dwell times, and improved on-time performance across their networks."

Jan 1, 2018

By Mike Samuels, John Starkey

"This paper examines test results and grinding mill design for the recent Fortune Minerals’ NICO Project, located in the Northwest Territories. SAG milling and rod milling options are compared. Rod milling is clearly shown to be the best option because of the ore’s extreme resistance to breakage in a SAG mill environment.Surprisingly, the Bond Ball Mill Wi was 13 kWh/t for this ore. The Bond Rod Mill Wi was 20 kWh/t, whereas the SAG pinion energy to grind the ore to T80 1.7 mm was 30 kWh/t. The existence of ore with this ratio of SAG hardness to Bond BM Wi has not been previously observed. If not considered, this critical relationship may adversely impact the accuracy of mill design. This paper substantiates the significance of these findings to achieve successful grinding design on ore that is macro-competent during primary size reduction, but relatively normal during secondary grinding.INTRODUCTIONThe NICO Cobalt-Gold-Bismuth-Copper deposit is located 160 km northwest of the City of Yellowknife, Northwest Territories. It is the largest IOCG-type deposit (aka Olympic Dam-type) currently recognized in Canada with Mineral Reserves of 21.8 million tonnes contained within a larger 57 million tonne, lower-grade Mineral Resource. The project, owned 100% by Fortune Minerals Limited, has been assessed in a positive definitive feasibility study, subject to underground test mining and pilot plant testing, and is now in the permitting stage to develop a combined open pit and underground mine and process plant. An updated process flow sheet incorporates conventional crushing, grinding and bulk flotation, followed by filtration for shipment of a concentrate to a purpose-built refinery proposed to be built near Saskatoon, Saskatchewan. At the refinery, separate bismuth and cobalt concentrates will be produced following regrinding. The hydrometallurgical process methods include: pressure acid leach, precipitation, ion exchange, and electro-winning for recovery of cobalt as 99.8% cathode; solvent extraction and electro-winning of by-product copper cathode; ferric chloride leach and electro-winning for recovery of bismuth as 99.5% cathode; and cyanidation of the leach residues for recovery of gold as doré."

Jan 1, 2010

By Y. Z. Xu

This paper presents a new dynamic method called Resonant Pile Test (HPT) for evaluating bearing capacity of pile. The basic conception of RPT is given in brief and the measuring system is also introduced. In addition, the influences of the magnitude of exciting force and of the mass of pile cap on test results are discussed. Finally, comparisons between values of bearing capacity given by RPT and by static load tests for a variety of pile types are listed.

Jan 1, 2010

By Tony Lipiec, Greg Gosson

"When it comes to new mines being developed, there is a general industry consensus that most low-hanging fruit has been picked. Many projects currently in the mine development pipeline have been around for decades, but were held back because of technical challenges. Future development of these deposits will likely require access to the public capital markets, and in Canada that means providing scientific and technical disclosure on these deposits in compliance with NI 43-101. As many of these “challenged” projects have metallurgical issues, the companies that own the projects need to ensure their metallurgical Qualified Persons provide transparent disclosure regarding proposed solutions to those issues.This paper provides an overview of the disclosure requirements under NI 43-101 that are pertinent to metallurgists, and other Qualified Persons who prepare technical disclosure regarding the metallurgical characteristics of a mineral project. It lists the triggers for a technical report under NI 43-101 and Canadian stock exchange policies, and identifies the sections of the report that should involve input from a metallurgist or process engineer. It briefly outlines new civil liabilities under Canadian securities laws that increase the possible consequences for not complying with the technical disclosure standards.These materials are provided for general information purposes only and do not constitute legal advice. Readers are advised to seek specific legal advice from their own legal counsel in relation to any decision or course of action contemplated."

Jan 1, 2010

By A. Gourlie

"This paper describes the performance properties of a new 95 ksi minimum yield strength, oil well casing grade designed specifically to resist hydrogen sulphide stress corrosion cracking, SSCc. The new grade, Soo-95SS, demonstrates NACE Tensile threshold values greater than 90% specified minimum yield strength, SMYS, and NACE Bent Beam values in excess of 12.7 x 1()4 psi. The new Soo-9588 grade also exhibits superior collapse and notch toughness values. IntroductionIn recent years, a trend toward casing grade specialization has resulted in the introduction of numerous proprietary grades designed specifically for particular production environments, In response, Algoma Steel has developed, as part of a "" grade for service"" philosophy, two new 95 ksi minimum yield grades. The two grades are Soo-95, High Collapse (HC), and Sour Service (SS). This paper describes the development of Soo-95 Sour Service.Four main objectives were established:1. Definition of the steelmaking and continuous cast processing practices2. Determination of the acceptable maximum and minimum levels for all chemical elements3. Definition of special processing requirements4. Definition of the physical characteristics and ranges of the product properties.This paper provides a description of the experimental approach, followed by a presentation and discussion of the trial results . Finally, a number of conclusions are given."

Jan 1, 1988

By Elizabeth Varghese, Sanket Rawat, Prachuryya Kaushik, Ravi Kant Mittal

"Geo5 Software is gaining popularity worldwide due to its expediency in analysis and design of pile foundation. The analysis is based on various theoretical, empirical and semi-empirical methods available in existing literature and various country standards. Moreover, the ultimate resistance of pile in the software is based CSN 73 1002, Fellenius method, NAVFAC DM 7.2 and Tomlinson method. Due to the specificity in calculation of ultimate resistance, it becomes necessary to validate the results arrived using the software for better accuracy. Furthermore, the above-mentioned methods are not necessarily popular in every design offices. Therefore, an attempt has been made to predict the efficiency of Geo5-v15 software to analyze the pile foundation by comparing it with the results obtained using the analysis based on Indian Standard IS 2911:2010, performed with spreadsheet specifically designed for the same purpose. The accompanying outcome of the comparison and several shortcomings found in the design part associated with the software has been highlighted in the later part of the paper. Besides, the optimization tool present in the software is also described for the more efficient and economic design of pile foundation, hence contributing as practical aid to structural engineers.INTRODUCTIONThe analysis of individual pile foundation and pile in groups can be said to include the three main important parameters – Ultimate bearing capacity, Settlement and Structural Design. The first two parameters are to be evaluated to check the reliability of foundation against ultimate limit state and serviceability limit state. The third parameter includes the analysis of pile against both horizontal and vertical load. This parameter mainly intends to evaluate the size of foundation and the amount of reinforcement. Geo5 is a software which can expediently compute the above mentioned three parameters just by the mere input of the necessary factors. The ultimate bearing capacity analysis in Geo5 is based on various theoretical, empirical and semi-empirical methods available in existing literature and various country standards depending upon the drained and undrained condition of soil (Bowles, 1968; CSN 73 1002,1987; Felenius,1991; NAVFAC DM 7.2,1984; Tomlinson,1977). However, the method mentioned in IS 2911 (2010) is not the same and have slight variations in way of evaluating the parameters which affect ultimate bearing capacity. Therefore, it becomes necessary to evaluate the efficiency of Geo5 with respect to the value of ultimate bearing capacity and therefore, asserting the confidence in the software based method for the convenience of the designs in Indian Scenario. The present study aims to evaluate the efficiency of Geo5 v-15 software in predicting the ultimate bearing capacity of pile foundation. The results of the software are compared with the bearing capacity calculated using IS 2911 (2010) with the help of excel sheet. Moreover, as the software is frequently put under revision, therefore a comparison of this version has also been made with the latest version of Geo5 (2017) to check whether the latest revision has accounted for the discovered shortcomings. The design steps performed in the software is also shown. As Geo5 make use of IS 456 (2000) for the design purpose, hence it can be considered as reliable with respect to the estimate of the third parameter. Furthermore, the optimization process is also shown in the later part of the paper to emphasize the simplicity of the software in economizing the design cost."

Jan 1, 2017

By Choi Sang-Ken, Chung Hun-Saeng, Kim Byoung-Gon, Lee Jae-Jang, Park Chong-Lyuck

"Graphite has unique properties such as high thermal resistance, low thermal expansion coefficient, and good thermal and electrical conductivity, and is often utilized as coating materials for electrical conductors, TV Brown tubes, electromagnetic shields, and so on. Additionally, its excellent lubrication property is widely used in oil and solid lubricants. Finely ground graphite particles in the sub-micron range are commonly used for these applications.Sub-micron fine graphite particles are typically prepared in liquids by vibration ball mills. However, it is known that the wet process takes long periods of grinding time like 24 hours or more and requires a series of subsequent highenergy operations such as de-watering, drying, regrinding and classification. On the other hand, there would be numerous advantages if fine grinding could be done effectively in dry atmosphere. However, since crystalline graphite has a layered structure giving a high lubrication property, its dry grinding, especially when obtaining sub-micron size particles, is extremely difficult. The shape of the graphite particles is also important for its utilization since particles with flaky shape can maintain relatively high electrical and thermal conductance as well as lubrication ability. Therefore, it would be necessary to reduce the size of graphite particles into fines with flaky shape while grinding proceeds. Dry grinding characteristics of natural graphite under various atmospheric conditions with gases using different mills were studied, and fine flaky particles by grinding the graphite intercalation compounds and the exfoliated graphite were produced. However, there were no sufficient investigations on the size reduction of natural graphite at low atmospheric pressures in attritional milling conditions. The main purpose of this paper is to provide sub-micron fine grinding characteristics of natural crystalline graphite at various degrees of low atmospheric pressure, and to discuss the size reducing models in an attrition mill"

Jan 1, 2003

By J. A. Bakken, M. Tangstad, P. A. Eidem

In the submerged arc production of ferromanganese, sillicomanganese and ferrochromium, the coke bed characteristics play an important role. The basic mechanisms of electric current conduction in the coke be dare not yet fully understood, but important parameters are the material resistivity of coke and the contact resistance between the coke particles. Preliminary tests indicate that the contact resistance is of great importance to the bulk resistance of the coke bed. An apparatus measuring the material resistivity and contact resistance of carbon materials has been developed. Both graphite and industrial coke have been tested. The material resistivity tests were performed on single particles to ensure that the effects of pores and cracks were included and the contact resistances were excluded. Two geometries were tested to obtain the contribution of the contact resistance to the total resistance of two connecting particles. The tests were performed in an inert atmosphere at temperatures and current levels found in industrial submerged arc furnaces. The results show that the method has a satisfactory reproducibility. It was found that the contact resistance is about 10 times higher than the resistance of the material when two particles are in perfect contact and that the resistivity of SSAB coke is more than 10 times higher than that of the graphite at room temperature, but with increasing temperature the difference decreases. For SSAB coke the general trend is that both the resistivity and the contact resistance decrease with increasing temperature.

Jan 1, 2007

The Coal Resources Survey commenced in 1974 as a search for Huntly Power Station coal, but soon developed into the most detailed regional coal search programme to be instituted in New Zealand. The program was initially conceived as geological in nature, but later included geotechnical, geohydrological, mining assessment, coal use, and environmental considerations in its investigations. The programme never undertook development work but has provided Government and the private sector with a sound basis for identifying development options. The discovery of large-scale coal resources in the Mokau, Waikato, and Taranaki regions and the lignite resources of Otago and Southland are a measure of the Survey's success. The directive by Government to phase out the NZCRS to a large extent coincides with the completion stage of the program. With most of the detailed regional study finished, it now remains to collate the data and publish summary reports at Coalfield and Coal Region level, in order to maximise the use and value of the data collected over the years.

Jan 1, 1987

By William Detty

An architect representing the Atlanta office of the Brick Institute of America periodically presents a slide lecture to interested groups entitled "The First 10,000 Years of Brick". The title signifies the fact that brick, man's oldest manufactured building material, has been around for quite some time and will continue to be utilized by architects and builders in the foreseeable future. This is not to say that the brick industry can rest on its laurels and ignore the competition presented by newer more innovative products. The industry will have to be equally inovative and market oriented in order to maintain its market share of the predicted construction boom between now and the year 2000. The implication is made, however, that brick can be produced under rudimentary conditions and that the desire to use the product has been long standing. In addition, history has sham that there has been plentiful clay available to produce the product. This paper is an attempt to assess the climate in which the brick industry will operate during the next 26 years. An analysis of regulatory conditions affecting the manufacture of the product will be followed by an assessment of the materials environment in which the industry will be operating. These factors are then reconciled with a projected demand for the product to determine the ability of the industry to satisfy future demand for brick. From a mineral point of view this paper will address itself generally to the availability of and demand for clay. However, other than a brief overview of the uses of other specific types of clay, it will concentrate on the clays utilized in the production of structural clay products, specifically brick.

Jan 1, 1974

By John C. Machisak

THIS CHAPTER of the Minerals Yearbook (volume III) contains overall injury experience and employment data at bituminous-coal, lignite, and anthracite mines, coking plants, metal and nonmetal mines, metallurgical plants, and stone quarries in the United States for the calendar year 1956. Volume I of the Yearbook includes injury experiences and related employment data in the metal, nonmetal, and quarrying industries, and in the milling operations connected with the mining of those commodities. Volume II contains the injury and related employment experience of the coal mining, coking, and oil and gas industries. Reporting is voluntary on the surveys conducted by the Bureau of Mines to collect injury and employment data in the mineral industries, except in the coal-mining industry, where operators are required by Federal law to furnish the information requested.

Jan 1, 1958

By Michael J. Kelly

IAMGOLD?s Westwood project is the site for the largest, by volume, bored vent raise in North America. When completed, it will be the fifth largest bored worldwide in a single pass. This paper will review the highest capacity raise drill system ever built (Redbore 100); as well as the technical difficulties in a single pass boring a 2,773 ft x 20 ft to 22 ft diameter raise. The difficult ground conditions and associated problems will be reviewed, as well as the solutions to overcome them. Use of the RVDS drilling tool to achieve .04% accuracy (14.5?) and the Geotube® water filtration system will also be covered.

Oct 1, 2010

By K. Goshtasbi

The mechanical behaviour of schistose sedimentary rocks such as slate show a great amount of anisotropy. Hence, the schistocity plane is essential when investigating the mechanical behaviour of such rocks. The presence of such rocks in civil projects causes non-symmetric deformation and their behaviour is unpredictable. In this research, the anisotropic strength behaviour of slates is studied. Uniaxial and triaxial tests were conducted on specimens having orientation angles (ß) of 0, 30, 45, 60, 75 and 90 degrees. The triaxial tests were done at confining pressures of 3, 5 and 10 MPa. The effect of anisotropy on uniaxial and triaxial strength, cohesion, angle of internal friction and Hoek and Brown's m and s constants were investigated. The results indicate that the strength of slates in uniaxial and triaxial compression exhibit a U-shaped anisotropic behaviour. In-order to evaluate the most suitable criterion for predicting the anisotropic strength of rocks in uniaxial and triaxial compression, an investigation was carried out on various criteria. In uniaxial compression, the Liao and Huong and Ramamurthy criteria had good agreements with the test results. In triaxial compression the Hoek and Brown and Mc Lamore criteria had better agreements with the test results. It should be noted that in-order to utilize these criteria, a large number of tests must be carried out. However, as the Ramamurthy criterion needs fewer test results, it can be the most suitable for investigating the behaviour of anisotropic rocks in triaxial compression. Keywords: Slate, anisotropy, schistose, failure criteria

Jan 1, 2006

By J. T. Fyles, C. G. Hewlett

"THE TOWN OF Salmo, rail centre for the Salmo lead-zinc mining district, is in southeastern British Columbia 26 miles by road east of Trail an about the same distance south of Nelson. The belt in which the mines occur is a few miles east of Salmo and extends about 6 miles north of the town and 17 miles south and southwest to the International Boundary. The belt includes the H. B. mine of The Consolidated Mining and Smelting Company of Canada, Limited, the Jersey mine of Canadian Exploration Limited, the Reeves MacDonald mine, and the Jack Pot property of New Jersey Zinc Explorations Limited.Since 1949, the Jersey and Reeves MacDonald mines have produced most of the lead and zinc in the district. From 1949 through 1954 these two mines together produced a total of 233,134 ounces of silver, 87,659,399 pounds of lead, 215,708,856 pounds of zinc and 475,397 pounds of cadmium. This amounts to more than 80 per cent of the total production of lead and 95 per cent of the total production of zinc from the district since the first recorded production in 1906. Reserves at the largest properties amount to several million tons of ore containing 4 to 7 per cent combined lead and zinc. Several prospects are potential producers.Regional StructureThe main structural units in the Salmo area are outlined in Figure I, and the major rock units of the stratigraphic column are listed in the following table. The lead and zinc deposits are replacements in a highly deformed limestone formation near the base of the Laib group, and all mineralized zones are on the south and east side of structural unit 2 (see Figure I)."

Jan 1, 1949

Viscosity measurements were carried out on slags in the CaO-Cu2O-CuO-MgO-SiO2systemcontaining ~ 63 wt% SiO2in air. The experimental work was carried out over a range of temperatures where the slags were completely liquid. Initial measurements were on a binary CaO-SiO2slag to which incremental additions of CuxO-MgO-SiO2slag with the same silica mole fraction were made. The viscosity-temperature relationship was measured for slags with‘Cu2O’contents of 0.02, 0.19, 0.38, 0.79, 1.69, 2.47, 3.01, 5.31 and 10.0 wt%. The proportions of Cu+and Cu2+in the slags were determined. The oxidation state of Cushifted from predominantly Cu+to Cu2+, with the Cu+/Cu2+ratio of approximately 0.3 for slag with a Cu content above 2 wt%. This is equivalent to Cu1.13O. The trends observed for changes of Cu2+/Cu+redox ratio with slag chemistry were consistent with the literature. Decreasing the CaO content by substituting copper oxide resulted in a decrease in the Cu+/Cu2+redox ratio. The change in ratio corresponded to a shift of the value of x in CuxO from an initial value of 1.8 to 1.1,when the slags contained 10% ‘Cu2O’. In this study, the SiO2content of the slags varied between 64 and 60 wt% as the Cu content increased. The viscosity of the slag containing 10 wt% CuxO was nearly 4.5 times lower than the binary CaO-SiO2slag. As the silica mole fraction (xSiO2) actually stayed constant (0.61±0.009),the results show that CuxO acted as a network breaker. Comparison with other ternary slags with similar silica mole fractions suggest that that addition of CuxO to silicate slags has a stronger effect on lowering the viscosity than FeO or MnO has on a molar basis. Keywords: viscosity, copper, silicate, slags

Jan 1, 2004

By Steve Dubnewych

The Joint Water Pollution Control Plant, operated by the Sanitation Districts of Los Angeles County, treats wastewater generated by over three million people. A new tunnel and ocean outfall is being considered to meet future hydraulic demands and provide long-term redundancy for the Districts? existing tunnels, portions of which were constructed as early as the 1930s. The detailed process used to evaluate the feasibility of various tunnel and out-fall locations is described. Challenges include a geologic profile with mixed face and squeezing ground conditions; high water pressures; active fault crossings; gassy and contaminated ground conditions; and liquefaction, slope stability, and lateral spreading concerns in the area of the riser and diffusers.

By F. Dai

Due to difficulties associated with gripping in direct tension, indirect methods are commonly used to measure rock tensile strength. In this work, we adopt an innovative indirect tensile test method: Semi-Circular Bend (SCB) to measure the tensile/flexural strength of Laurentian granite (LG). The static tests are carried out with a servo-controlled material testing machine and the dynamic tests are conduced with a Split Hopkinson Pressure Bar (SHPB) system. Pulse shaping technique is adopted to achieve dynamic force equilibrium in SHPB to facilitate data regression. Finite element method is used to relate the failure load to the tensile strength. Strong rate dependence of the tensile strength is observed. The flexural strength is higher than the tensile strength measured using Brazilian Disc (BD). This difference is rationalized using the non-local theory. To further validate the method, a coupled Finite element/Discrete element method (Fem/Dem) in conjunction with the smeared crack model is utilized to simulate the fracture process during dynamic SCB tests. The resulting fracture patterns are qualitatively consistent with those from recovered samples. Both the experimental and numerical methods have validated the results and this new method is readily to be used for other rocks and other brittle materials.

May 1, 2009

As part of a comprehensive risk analysis which was carried out into the effectiveness of the water barrier between South Deep and Randfontein Estate mines, the potential threat posed by large seismic events was assessed. The study covered several aspects. Firstly, an estimate of the maximum credible earthquake was obtained from a probabilistic analysis of the regional seismicity of the previous 25 years. Allowance was made for ?reservoir-induced? effects by increasing the estimate of the size of the maximum credible earthquake from ML= 5.1 to ML= 5.5. Based on available knowledge of the geological structure, the possibility of such an event occurring in the vicinity of the barrier pillar was estimated. The possibility of substantial damage to the barrier rock mass, resulting as a consequence of a large event, was assessed. The likely damage to the concrete control plugs installed in five tunnels that penetrated the barrier, which might result from a ?near-miss? by the largest possible seismic event or from a ?direct hit? by a smaller event, was also considered. It was concluded that there was a negligibly small possibility that the maximum credible earthquake could occur close enough to the barrier, and in such a manner, as to cause any damage to it or to the plugs in the tunnels passing through it. The possibility of serious plug damage occurring as a result of a ?direct hit? by as maller event was slightly greater, but still sufficiently remote as to be of no practical concern at all.

Jan 1, 2006