Search Documents

By Yang Song, Li Shaokang, Wang Zhiqiang, Wang Jinjun, Li Guofeng, Su Meixuan

CaCO3, as a component widely existing in natural minerals, is a common impurity. In recent years, triboelectric separation has been applied to the separation of minerals containing CaCO3. However, the CaCO3’ s tribocharging mechanism is still unclear and the charging effect of CaCO3 is not obvious. In order to study the effect of triboelectric charging of CaCO3 particles under different conditions, according to the single particle frictional collision charge-mass ratio formula derived from the condenser model, an experimental platform for particle tribocharging was built in this paper. Then, the formula of charge-to-mass ratio (Q/m) was derived based on the analysis of the particle force. Particle image velocimetry (PIV) was used to record particle motion trajectories to calculate the Q/m of one particle by this formula. In the experiment, the airflow velocity, tribocharge material, and moving distance of the particles were varied to investigate the variation of the particle charge-mass ratio results. The results show that CaCO3 was negatively charged when tribocharging with mental. The particle’s Q/m is positively correlated with the airspeed. When the metal is triboelectrically charged with the insulator, the metal with a smaller work function leads to the insulator particle with a larger Q/m. As the moving distance of the particles increases beyond 230 mm, the particle charge ratio decreases. The particle charge-mass ratio is consistent with the trend of the charge-mass ratio deduced from the capacitance model.

Jun 3, 2023

By Kyle A. Perry, Ethan A. Steward

The mining of underground coal presents several hazards for miners, including the risk of an explosion fueled by methane gas and coal dust. Methane gas, produced during coal formation, can continuously leak into old workings and build up through its lower explosive limit. Underground coal mines are required to maintain safe conditions, either by ventilating old workings or sealing them off using approved methods. Seals must be designed to withstand instantaneous pressures for a minimum of four seconds. A design strength of at least 50 pounds per square inch (psi) is required for atmospheres monitored and maintained inert, 120 psi for non-inert or not monitored, and greater than 120 psi for special cases. Due to the high cost and testing environment availability, most mine seals are designed through calculations and computer modeling and not subjected to full-scale testing in a representative environment. High pressure is not the only threat that mine seals may be exposed to. During an underground explosion, pressure waves and gas expansion may propel common mine items and objects to a high velocity, generating enough energy to damage mine seals and reduce their strength. Damaged mine seals may fail to contain their rated pressure, allow high pressure gas and fumes to vent through the seal during an explosion, or allow gasses to leak through the seal later after an explosion has occurred. This paper examines the effects of high velocity impacts of common mine materials and items on a reinforced mine seal rated to 120 psi.

Jun 2, 2023

By Wei Victor Liu, Na Zhang, Chengkai Fan, Bei Jiang

This study used artificial neural networks (ANNs) coupled with Gaussian mixture modeling (GMM) to analyze truck haulage data from openpit mines. The proposed weighted ensemble models performed better than benchmark models in predicting truck productivity, providing a new means of solving complex data and improving mine planning and decision-making.

Jun 1, 2023

By Juan J. Monsalve, AMAN SONI, Nino Ripepi, Richard Bishop

The design and strength of pillars are important parameters when implementing the room-and-pillar mining method in a limestone mine. The process becomes complex with the presence of karst voids, which are frequent phenomena in carbonate rock formations. This research continues a previous study aimed at studying the effect of karst voids on the strength of a particular limestone pillar. Using calculated pillar strength and estimated redistributed stresses, it was assessed that the pillar can counter more stress than currently imparted on it. Numerical modeling studies combining in situ stress determination and excavation sequencing were used to estimate the existing stresses on the pillar. Different possibilities of modification to existing pillar design were simulated using distinct element method (DEM) modeling to determine a better design.

Jun 1, 2023

By Irina Chernyshova, Erik Larsen, Hanumantha Rao Kota, Vladislav Slabov, Garima Jain

The mining industry faces pressure to provide metals for the green digital shift using sustainable technologies. This study evaluates biosurfactants as collectors for ultrafine and coarser particles of hematite and malachite, aiming to improve the flotation of ultrafine particles.

Jun 1, 2023

By Yueyue Ding, Yuanhui Li, Zhengrong Li, Pengfei Yu, Kunmeng Li, Zhipeng Xiong

The overburden responses in gently inclined orebody mining are different from those in horizontal orebody affected by the orebody dip angle. In particular, the mining-induced stress presents asymmetrical distribution characteristics spatially, resulting in stress concentration and large-scale pressure relief phenomenon in the surrounding rock. As a result, frequent ground pressure disasters such as roof collapse and barrier splitting occur frequently. Moreover, the ground pressure evolution law and the interaction between stopes in multistope mining are complex. The effective ground pressure control measures cannot be taken due to unclear understanding of the evolution of stress and displacement fields, justifying the investigation of the distribution and evolution of underground pressure for safe and efficient mining.

Jun 1, 2023

By Ihsan Berk Tulu, Haochen Zhao, Deniz Tuncay

The process of designing pillars and selecting support measures in underground coal mines relies highly on the accurate assessment of mining-induced loads and the load-bearing capacities of the supports. This study proposes a new method to estimate the percentage of load carried by the gob in underground coal mines using a new parameter that introduces the site-specific overburden geology.

Jun 1, 2023

By Aixiang Wu, Minjie Zhang, Zhuen Ruan, Yiming Wang

This paper combines theoretical and experimental analysis to conduct relevant research to improve the accuracy of predicting paste yield stress by slump flow. The analytical model of slump flow for yield stress is derived based on a mini-cylindrical mold with a height-to-diameter ratio of 1. It shows that the dimensionless slump flow is a monotonic decreasing function of the dimensionless yield stress and is independent of the material type (specific gravity), which provides a theoretical basis for quantifying the rheological properties of paste with slump flow. Three different tailing-prepared pastes were tested for their slump flow and implemented rheological tests simultaneously. The yield stress is obtained based on the Bingham model fit, as the measured value of the yield stress is substituted into the derived theoretical model. The studied pastes yield stresses range from 34.78 to 524.08 Pa, with corresponding dimensionless slump flow of 3.43 to 1.09. The results showed that the calculated slump flows were generally greater than the measured values. The analysis showed that this was mainly due to the thixotropy of the paste, with minor deviations ranging from − 1.5 to 5.8% for the less thixotropic pasted prepared from tailing C. An approximate analytical solution for yield stress as a function of slump flow is obtained using Taylor’s formula. However, it is unsuitable for predicting the yield stress because the yield stress calculated by this function is much higher than the measured value. The empirical yield stress model was constructed and experimentally verified. The results show that the empirical formula has high accuracy and good generality. The deviation of the studied pastes is between − 15 and 5%, which provides a practical method for rapid and accurate prediction of paste yield stress in mine sites.

Jun 1, 2023

By Brendan Demich, Brendan Macdonald, Timothy J. Orr, Jonathan K. Hrica, CASSANDRA L. HOEBBEL, Jason Navoyski, Jennica L. Bellanca

Haul truck fatal accidents and injuries continue to be a significant concern for the mining industry. However, the availability of high-quality training materials continues to be limited. Near-miss incident accounts, if packaged well, could help fill this gap, because for every fatality, there are hundreds of reportable accidents and thousands of undocumented near misses. Researchers from the National Institute for Occupational Safety and Health (NIOSH) collected detailed accounts of 21 near-miss incidents in virtual interviews with mineworkers at surface mining operations across the country. From these interviews, researchers created four simulation videos using the Unity game engine. The simulation videos bring these events to life through first-person retelling and various visual perspectives of actual events. Each video exemplifies a critical safety message and a common haul truck hazard. This paper describes the process of taking narratives and turning them into impactful visual stories using graphic simulation. NIOSH plans to co-release these simulation videos with the Mine Safety and Health Administration (MSHA) to the mining industry to raise awareness and ultimately help reduce haul truck-related accidents and fatalities in mining.

Jun 1, 2023

By Bahaa Alyosif, Murat Erdemoğlu, Muhammet Kürşat Aydemir, Turan Uysal

The effect of intensive milling on the conversion of microcline ( KAlSi3O8) to potassium chloride (KCl) occurred during the chlorination roasting process for artificial KCl production was investigated. A feldspar ore with 10.89% K2O grade and containing microcline was dry milled by a planetary ball mill for mechanical activation. Milled ore mixed with calcium chloride was roasted at temperatures between 500 and 1000 °C to get the chlorination roasting process. The product was then leached in water to dissolve KCl occurring during the roasting, which will be precipitated from the pregnant leach solution by evaporation. Results showed that potassium recovery from the unmilled ore increased rapidly up to 800 °C, and dramatically decreased at higher temperatures due to the removal of KCl from the furnace by means of evaporation. A potassium recovery of 31.95% was achieved by the unmilled ore, whereas it was 88.43% when 15 min milled ore was roasted at 750 °C. It was concluded that intensive milling caused mechanical activation of microcline to reduce the roasting temperature of the chlorination roasting process.

May 31, 2023

By Anup Tiwari, Khanindra Pathak, BIBHUTI BHUSAN MANDAL

Failure of in-pit overburden dumps in open-pit coal mines causes debris to flow toward the active working face, threatening the safety of people and equipment. The evaluation of the potential mobility of failing mass will aid in hazard mitigation associated with unwarranted dump failure. The potential mobility is shown by mobility ratio (ratio of total drop between debris flow's initial and final deposition points to total travel distance) and runout characteristics. In light of above, a laboratoryscale debris flow flume was developed to investigate the effect of material gradation and slope angle on runout characteristics and mobility ratio. The total mass of experimental debris mix (Q) is fixed at 30 kg with 20% water content. Experiments at three different slope angles (30°, 35°, and 40°) demonstrate that increasing the proportion of fines in the experimental mix increases runout characteristics while decreasing the mobility ratio. The length and area of the runout decrease as the slope angle increases, while the mobility ratio increases. There is a positive correlation between d50 and runout characteristics at a fines content of 0.1Q, but a negative correlation at a fines content of 0.2Q and 0.3Q. Conversely, there is a negative correlation between d50 and mobility ratio for fines content of 0.1Q, but a positive correlation exists for fines content of 0.2Q and 0.3Q. A new index called the fine-to-coarse (F/C) ratio is used to identify the critical value of fines and coarse proportion that causes a transition from dry granular flow to fluidized debris flow.

May 29, 2023

By Amar Prakash, V. M. S. R. Murthy, VIVEK KUMAR HIMANSHU, Sufal Mehrotra, Ashish Kumar Vishwakarma

Raises are vertical or inclined openings made to connect two levels of an underground metalliferous mine. They are developed using drilling and blasting-based technique or by mechanical means. Raise boring machines (RBM) have evolved in recent years, which provide quicker and safer raise excavation. The penetration rate using RBM has influenced applied thrust. The required thrust to enhance penetration rate with optimal use of energy would be different under varying geological and geotechnical conditions. In this study, the influence of applied thrust on penetration rate using RBM has been investigated. The investigation has been made for two different rock types, amphibolite (AMP) and garnet-biotite-sillimanite-gneiss (GBSG). The numerical simulation model was developed for this purpose using Ansys-Explicit Dynamics. The induced tensile stress under different conditions of applied thrust has been analysed in the calibrated numerical model. The model output shows the power trend between the parameters. The experimental data on penetration rate was also collected along with the respective operational parameters. A statistical analysis has been carried out for the gathered data. The analysis of data also shows a power trend between thrust per cutter and penetration rate in both rock types and hence validates the numerical simulation-based output. Based on the outputs of the numerical simulation and empirical study of the experimental data, the optimum thrust per cutter for excavation in both rock types is in the range of 12–14 tons. The approach used in this study can be helpful for predicting the optimal operational parameters of raise boring machines under different geological/geotechnical conditions.

May 29, 2023

By D Hope, D K. Mukhopadhyay, J D. Harvey

South32 (S32), a globally diversified mining and metals company, is listed on securities exchanges around the world (ASX, JSE, LSE), with its primary listing being on the Australian Securities Exchange (ASX). Chapter 5 of the ASX Listing Rules (Australian Securities Exchange (ASX), 2019b) requires a mining entity to provide a summary of governance arrangements and internal controls with respect to its estimation processes, estimates and reporting of Mineral Resources and Ore Reserves annually. As a global company, it is also important to design and implement all governance processes and internal controls which can be used consistently across the organisation. The three lines model (previously known as the ‘three lines of defense’ model) is employed across South32 to manage risk where the first line (Practitioners) designs, implements and executes processes and controls to manage risk; the second line (Stewardship) identifies material gaps and improvement opportunities in the first line by monitoring conformance with the group requirements, legislative and regulatory obligations. Second line also assists with the development and improvement of core fundamentals based on industry good practise. The third line (Group Assurance) provides independent and objective assurance over the Group’s system of risk management and control. The estimation of resources and reserves for most of the operations within South32 is managed by the Planning function. The estimation process is part of the annual Life of Operation Plan (LoOP). The LoOP identifies and assesses the strategic alternatives for the development of an operation and recommends the preferred pathway based on value and risk. The LoOP starts with opportunity framing and the updated resources as an input and ends with the short-term plan and annual budget (the outputs). Ore Reserves estimates are one of the outputs from the LoOP. All the inputs and outputs follow internal standards and procedures which includes peer review and performance reconciliation. Stewardship (Second line) which is a centralised function has standards in place to ensure compliance to internal controls and external regulatory requirements. This includes assessment of the competence of Competent Persons, technical reviews, independent audits and training in the relevant chapters of the ASX Listing Rules, Guidance Notes and Appendices. Group Assurance (Third line) which reports to the Risk and Audit Committee of the Board of Directors ensures the design and operating effectiveness of the processes, standards and procedures associated with the estimation and reporting of resources and reserves. While the level of scrutiny has a different intent for each line in the three lines model, the overall purpose is to achieve a consistent outcome across the organisation

May 24, 2023

By G Zhang, I Glacken

Multiple indicator kriging (MIK) has been used in the minerals industry for some decades. As one of the non-linear estimation methodologies, MIK has advantages related to resolving multiple or mixed populations, high variability data and strongly skewed distributions. Applying the MIK methodology requires a lot more effort when compared to other non-linear methodologies, for example localised uniform conditioning. This is due not only to the variogram modelling for multiple indicators, but the validation is also very important because the panel model is fundamental for follow-up work, including the generation of recoverable resources at the local or SMU scale. Apart from this, only a few reported case studies of MIK have documented post-processing of the estimated modelled distribution, representing the probability distribution at point scale at un-sampled locations. The MIK post processing should include the change of support from the point scale to the panel scale, and then the extraction of quantile values from the panel conditional cumulative distribution function (CCDF) for localisation of grades into the SMUs within each panel, based on a ranking estimate marking the SMUs from high to low. In this paper, we present a case study on a gold deposit with the MIK method with full-post processing implemented for recoverable resources. The MIK point estimate was carried out with an indirect lognormal change of support from point to panel scale, and localisation was done with a custom script. The localised uniform conditioning (LUC) method was also applied for comparison purposes. The comparison shows that MIK has advantages compared to LUC when comes to capturing the high-grades, especially when mixed or varying anisotropy is present within the mineralisation.

May 24, 2023

By D A. Sims

This paper outlines the contributing factors to a series of erroneous Mineral Resource estimates which led to considerable loss, including significant reduction of mine life and consequently a large write-down of asset value. The error prompted divestment of the mineral asset in the short-term by the owners, a major mining company. There were multiple and complex contributions to the result: • The mine was undergoing a transition in the deposit geology with increasing depth that was not accommodated in the models. Early indications of the geological transition in initial drilling were generally unrecognised in resource modelling. The shortcomings of the models became apparent with increasing infill drilling and subsequent production reconciliation. • There was a lack of recognition of, and confidence in, site-based input and skills by corporate technical management. The site had a reputation internally for over-delivery to plan early in its life and that supported the anticipation of ongoing metal delivery into the mine plan by management. • A corporate lack of confidence in site being able to adequately domain the mineralisation led to the use of a CIK domaining process, rather than one which was geologically based. This domaining process led to gross over-statement of mineralisation trends reflected in the subsequent OK estimate. • Timelines on the outsourced estimation process were so short that validation was not possible. Obvious errors in the estimate versus data were not able to be used to correct the issues and the site’s Competent Person sign-off occurred without adequate checks. This case study is presented to reinforce the concept that Mineral Resource estimates are not solely based on the ability of the Competent Person to satisfactorily guide the process. There are usually multiple complex issues in the estimation process which need to be recognised and considered in judging reconciliations of model to actual.

May 24, 2023

By M J. Nimmo

extremely powerful tools for building predictive and generative models. ML can be used for building highly accurate regression and classification models. But without careful data science and statistical analysis, a regression or classification model could be highly biased and completely wrong – and we may not even realise. An example rock density estimation task will be used to illustrate the potential gains and possible pitfalls in using ML and AI in Mineral Resource estimation. What could possibly go wrong? Nothing! For most simple regression or classification problems, very little. For density estimation, using the global mean may be all that is possible, but the resource classification would need to reflect the uncertainty in global estimation of tonnage. Everything! From data collection and measurement, from selecting ML and AI techniques and designing the analysis workflow to our own cognitive bias. The things that could go wrong are vast and may include but not limited to asking the wrong question, not asking questions, data bias, measurement errors, insufficient data coverage, not collecting the right variables, not collecting enough observations, collecting clustered samples, unbalanced data, filtering out data without reason (outliers), clipping data (outliers), relying on automatic feature selection, including irrelevant variables, excluding relevant variables, geological interpretation, changing context, blindly following best practice, splitting small data sets, subsetting large data sets, using the wrong tool for the task, insufficient budget to complete the analysis, not allowing enough time for testing and experimentation (the science), focusing too much on building the model (the engineering), not learning from the data, our assumptions, our preconceptions, and our skill. This paper will explore the question of how training regression models to predict rock density are affected by gaps in the data (missing observations and missing variables). What could possibly go wrong?

May 24, 2023

By W Patton

Investment decisions in the mineral resources sector are made on the basis of an assessment of the economic potential for a mineral deposit. Given the supporting information for the location, scale, and quantity of the commodity of interest, miners and investors aim to make risk-informed decisions when considering further investment. The objective of resource classification is the synthesis of various types and quantities of geologic information used in resource model construction to assign confidence categories to the estimated mineral resources, which can then be used to support informed economic decisions. In this paper a risk-based classification scheme for iron ore mineral resources using conditional simulations is presented. The method involves categorisation of each block according to a confidence level, considering expected recoveries from a kriging model over mining production volumes. The realisations of the simulated model are used to assign risk-based confidence categories to zones of the ore deposit. One motivation for this work is to assess the sensitivity of the scheme to geologic uncertainties. Specifically, that which uncertainty in the layout of mineralising alterations and weathering overprints influence variabilities of associated rock properties and the likelihood of obtaining expected ore recoveries. It is shown these risks have material implications for a project’s economic potential. How the scheme can be extended to the grade control context and the value subsequent grade control activities is also quantified.

May 24, 2023

By L Bertoss, D Carvalho

In the last decade, the use of advanced implicit modelling software/algorithms in mineral resource workflows has become a best practice in the mining industry. In most cases, these workflows can easily replicate the level of detail of explicitly modelled geometries, even for very complex deposits. These techniques are flexible and can produce fast results since software is responsible for generating 3D surfaces and solids based on geological and interpretation data. Nevertheless, depending on how unique and complex some deposits are, intense manual editing and input are required to honour the geological context and produce the desired outcome. The current geological modelling workflow at George Fisher Mine (GFM) is based on the semi-automatic built-in tool that generates stratigraphic sequences (stacked lithology layers) based on logging and mapping data. This tool (stratigraphic sequence from Leapfrog Geo™) works for the majority of areas in the mine but fails to capture observed mineralisation pinch-outs in operational areas and at extrapolated boundaries of the deposit. These pinch-outs have the potential to negatively impact grade forecasts if not resolved manually. Using built-in software tools only, the alternative for a more accurate model is to generate each individual layer and adding tens of thousands of manual interpretation points to honour pinch-outs (based on the amount of existing drilling in the mine and number of layers). This approach would require an estimated minimum of two to four years of a full-time employee (FTE) to be exhaustively completed. This study presents an automated approach to generate pinch-out points using a set of Python scripts that only take a few minutes to run. The newly generated points are then combined into the commercial software workflow as interpretation points, honouring observed pinch-outs. The remarkable time difference between approaches removes chance of manual errors and allows mine geologists to spend valuable time in validation and testing of scenarios, ensuring they are more representative of the deposit’s geology.

May 24, 2023

By H Arvidson, V Chamberlain, R Marinho, B Parsons, T Rowl, M Noppé, M Mattera

With the introduction of CRIRSCO (2019) based mineral asset disclosure, Regulation S-K part 1300, 2019 (S-K1300) by the United States (US) Securities and Exchange Commission (SEC), applicable to companies listed on the New York Stock Exchange from 2021, Mineral Resource is now required to be reported Exclusive of Mineral Reserve, referred to here as ‘Exclusive Mineral Resource’ (EMR). EMR is equivalent to reporting Mineral Resource additional to Mineral Reserve, which has been permitted in jurisdictions outside the US for many years. Despite this, there are no practical guidelines in the literature or relevant reporting codes and rules for Competent/Qualified Persons to refer to, which creates a risk that disclosure of EMR estimates across the industry will be inconsistent and potentially ambiguous for analysts, investors, potential investors, and other stakeholders.With the introduction of CRIRSCO (2019) based mineral asset disclosure, Regulation S-K part 1300, 2019 (S-K1300) by the United States (US) Securities and Exchange Commission (SEC), applicable to companies listed on the New York Stock Exchange from 2021, Mineral Resource is now required to be reported Exclusive of Mineral Reserve, referred to here as ‘Exclusive Mineral Resource’ (EMR). EMR is equivalent to reporting Mineral Resource additional to Mineral Reserve, which has been permitted in jurisdictions outside the US for many years. Despite this, there are no practical guidelines in the literature or relevant reporting codes and rules for Competent/Qualified Persons to refer to, which creates a risk that disclosure of EMR estimates across the industry will be inconsistent and potentially ambiguous for analysts, investors, potential investors, and other stakeholders.

May 24, 2023

By I Sucholutsky, D M. First, D Mogilny, F Yusufali

Machine learning is creating value in all facets of the mining industry, from exploration to production. The authors provide an accessible, high-level introduction to artificial intelligence (AI), machine learning (ML), and deep learning (DL); the latter being widely recognised as one of the most powerful forms of ML. In particular, the authors will introduce deep learning models known as convolutional neural networks (CNNs), how they are applied, and the economic considerations necessary for determining when DL may be the right solution to de-risking complex block modelling problems. The authors present preliminary results from the mineral resource modelling study of the Jundee orogenic gold deposit, Yandal belt/gold province, Western Australia. The primary goal was to identify the direction and location of the narrow gold veins more accurately and demonstrate how non-linearly correlated elements are used as direct inputs to the resource model to assist with the target element’s grade prediction. This demonstrates that: (1) existing techniques for finding correlations between assayed elements do not adequately reflect the complex geology of the asset, (2) nonlinear correlations that are difficult to model as simple mathematical functions are representative of geological patterns in a deposit, and (3) non-linearly correlated assayed data, fed as inputs, increase the performance of the resource model as reconciled through blind tests. To conclude, the authors hypothesise that the patterns represented by the DL block models may be revealing the results of overprinting geological processes that generated mineral deposits. For example, the primary hydrothermal processes that deposited metals created depositional patterns that become particularly complex as a result of being overprinted, in part or in whole, by secondary physicochemical processes. This may explain why non-linear geochemical relationships have the capacity to generate more accurate block models of mineral deposits.

May 24, 2023