Search Documents

By D. W. H. Su

This paper presents the results of ill situ horizontal stress measurements using a Minifrac system in several northern Appalachian coal mines. The effect of stress magnitude and orientation on longwall gate entry stability was analyzed using a series of three-dimensional finite element analyses. The best headgate stability is achieved if the maximum horizontal stress is aligned with the direction of longwall retreat or if the panel is oriented such that the maximum stress relaxes over the headgate due to the presence of the newly formed gob. The degree of horizontal stress damage to longwall gate entries depends largely on the stress magnitude and roof geology. Accurate assessments of support or design techniques which may mitigate longwall headgate or tailgate instability in areas of thinly laminated roof and high horizontal stresses must account for the in situ horizontal stress state and site specific roof geology. The ability to measure stresses and map geology is thus essential to prevent ground control failures at the longwall headgate.

Jan 1, 1995

By R. F. Korcak

There exists a wide array of industrial by-products that can be shown to produce beneficial responses in the soil/plant environment. These materials range from clean coal technology residues produced in the generation of electric power, particularly those high in gypsum, to mineral 'fines' produced by the aggregates and crushed stone industries. A number of these materials will be examined in relation to potential nutritional interactions in soils and crops with emphasis on trace elements. The significance of utilizing these materials in agriculture as a component of sustainable agricultural systems will be discussed.

Jan 1, 1995

In order to test the applicability of elastodynamic codes in the modeling of mining related problems, comparisons are made between seismic data and numerical analyses. The dynamic finite difference program WA VE is used for the modeling of a horizontal stope in a deep mine. The slip along a vertical fault situated within the positive excess shear stress lobe of the stope initiates seismic waves. The stope-fault geometry is modeled in both two and three dimensions. The three dimensional non-slip weakening WAVE analyses correlate well with Brune's analytical model. For accurate modeling of the peak particle velocities predicted by McGarr's empirical relationship, it is recommended that a three-dimensional stope -fault model is used, with the amount of slip weakening dependent on the magnitude of the event.

Jan 1, 1995

The Taupo Volcanic Zone inNew Zealand and the Philippine Mobile Belt in the Philippines are characterized by active subduction, active volcanism and high seismicity. The main factors affecting characteristics of geothermal systems in both countries are: tectonic setting, source magmas, maturity of the systems, and depth to the degassing magma body. Within New Zealand, geothermal systems are grouped into arc- and rift-type. Fluids in arc-type systems contain high amounts of volatiles (<20%), with high CO2/Cl, CO2/He, and N2/Ar ratios. Mantle-type volatiles predominate in rift-type systems. Philippine geothermal systems are largely arc-type, the topography is rugged, leading to the separation of water and vapour upflows, as opposed to the overlap found in New Zealand. The relatively shallow depths of degassing magma bodies in the Philippines results in steeper geochemical gradients, leading to higher proportions of arc-type magmatic water (>40%) and higher Cl contents (3000 - 10 000 mg/kg), Maximum temperatures are also higher, reaching up to >400¦C. Arc-type alteration assemblages in New Zealand and the Philippines are similar. Because Philippine geothermal systems are less mature, have higher temperatures and steeper geochemical gradients than New Zealand ones, advanced argillization is more widespread occurring down to depths of 2000 m. Mineral phases are more varied due to the active input of magmatic waters and the formation of vapor conditions at depth, forming P04-, B-, Li-, Ce-, F-, and Cl-bearing minerals at high temperatures. In the Philippines, high temperature magmatic-hydrothermal to contact metamorphic assemblages containing biotite, amphiboles and pyroxenes are relatively common, but rare in New Zealand.

Jan 1, 1995

By Patridge A. C

Observations of coal stockpiles subject to unusual levels of instability showed that the particular coals exhibited 'gap grading', a relative lack of intermediate size particles. This led to a suggestion that fine coal particles within the pile might have been induced to migrate under the influence of water flow and to concentrate in relatively impervious layers, resulting in local water saturation and reduction of shear strength. To investigate this suggestion, a large test column has been constructed and washed coals with various levels of fines content have been subjected to a downward flow of water. Subsequent examination of the bed of coal within the column confirmed the percolation of fines and their concentration into horizontal layers, and showed the development of zones of saturation above those layers. Shear box tests showed differences in cohesion and internal friction angle between coals with different percentages of fines, supporting the hypothesis that fines percolation may lead to decreased stability.

Jan 1, 1995

By McAuley T. J

Computer software is an integral part of mining operations today with many sites using six or more software packages on a daily basis. However, the use of these different programs generates the need for substantial staff training. The current trend toward large integrated packages to solve this problem is counter-productive because the relatively small companies producing specialised mining software do not have the resources to develop quality software with all the required features. Software standards are being proposed by various parties but recent history indicates these will be unsuccessful. An alternative approach is suggested using the various standards which have been developed for the Windows operating system.

Jan 1, 1995

By G J. Corbett, T M. Leach

A continued exploration programme has further defined the geology of the Tolukuma vein system, verified the resource indicated by Newmont, and identified potential for additional mineralisation. The resource at Tolukuma Hill, designated as zone C, is a mine recoverable 432,000 t at 18.1 g/t Au & 46 g/t Ag. Mining will be by a combination of open pit and underground at a rate of 100,000 t per annum. Processing will be by SAG mill, gravity circuit and CIL plant. A diatreme breccia, localised at an intersection of structures and a relationship of gold to base metal sulphides, are indicative of a strong porphyry association. Typical epithermal features such as crustiform banded quartz and quartz pseudomorphing platy calcite are also present and locally contain lesser gold mineralisation. Pre-existing dilatant structures have acted as a host to the ore fluids, resulting in the formation of the semi-continuous Tolukuma-Gulbadi veins over a 1100 m strike. A fluid flow model suggests that mineralizing fluids were sourced from a diatreme margin and migrated laterally along dilatant structures. Bonanza gold grades are interpreted to be derived through fluid quenching in the flexure between a hanging wall split, which hosts much of the Tolukuma Hill resource, and the feeder graben structure. Thus, the relationship between the pre-mineral structural geometry and fluid upflow at the margins of a diatreme breccia, controls the ore setting.

Jan 1, 1995

By N. C. Miller

In situ stope leaching is an innovative mining system that reduces the surface impacts of conventional underground mining. As in any leaching operation, stope leaching requires hydrologic site characterization and control of leaching solutions. Several tracer tests, using sodium chloride (NaCl) in various concentrations, were conducted by the U. S. Bureau of Mines (USBM) in an underground experimental stope to simulate a leaching environment. The tests were conducted in fractured crystalline rock that was partially saturated. As tests progressed, the surrounding fractures became more saturated. A predominant flow direction away from the stope was found during testing. Testing procedures, preliminary results, and remediation ideas based on field observations are presented in this paper.

Jan 1, 1995

By M. D. Chatham

Revolutionary electronic monitoring and control systems provide a gold mine of diagnostic and prognostic information. Lower cost per ton results from timely operator action, increased visibility of information to production and maintenance personnel, and better fleet management. When information is effectively integrated into fleet management systems lower costs result from higher availability, longer component life and reduced repair cost. This paper will present the objectives of the Caterpillar Vital Information Management System (VIMS) and provide actual examples of successful use.

Jan 1, 1995

By M. J. Klishis

This paper presents the findings of a study on roof bolters' hazard exposure. A "micro-analysis" of accident data was combined with ergonomic observations of roof bolter operators to categorize bolting-related injuries and a checklist was constructed. Bolting-related problems were identified as situations that could expose bolter operators to hazards. Approaches to avoid these situations were applied at six mining operations to evaluate specific problems in roof bolting operations. The re-search emphasized the importance of analyzing worker behaviors in the context of mining situations and equipment design problems that lead to human error accidents.

Jan 1, 1995

By Yoshiharu Tanaka, Toshiyuki Ichijo, Masaaki Yamamoto

We utilized electronic detonators (EDs) to investigate the effect of high detonator delay accuracy on overbreak, remaining rock damage, and surface smoothness, in comparison with that of long-period delay detonators (0.25 sec interval) PDs. The experiments were conducted in a deep mine, in a test site region composed of very hard granodiorite with a seismic wave velocity of about 6.0 km/see and a uniaxial compressive strength, uniaxial tensile strength, and Young's modulus of 300 MPa, 12 MPa, and 73 GPa, respectively. The blasting design was for a test tunnel excavation 8 m in cross section, with an advance per round of 2.5 m. Five rounds were performed, each with a large-hole cut and perimeter holes in a 0.4-m spacing charged with 20-mm-diameter water gel explosive to obtain low charge concentration. EDs were used in the holes on the perimeter of the right half, and PDs were used in all other holes.

Jan 1, 1995

By J. M. Dean

With the continued downward pressure on coal selling prices, mine management must make its operations as efficient as possible. The problem is the same one throughout the mineral industries, streamlining operations to maintain competitive mining costs (Born, 1991). There has been a great deal of research into better using production manpower. But the story is different for operations support personnel. Traditionally, planning man-power requirements are done annually, with modifications to the operating plan occurring generally quarterly. On the other hand, the demands on manpower are often dynamic, being responsive to changing productivity levels ,mine conditions (including water influx, bad roof, poor floor)and unanticipated project requirements (responses to machine breakdowns or a new section setup requirement because of a drop in coal quality in another area). Such changes may impact the manpower structure significantly. At times they may cause serious labor relations problems concurrently. Realignments and the generation of instability in the workforce because of active job switching (bidding) are a result. Most responses by coal operators are reactive rather than proactive, a situation that could be mollified by more accurate and detailed planning of predictable manpower requirements. A manpower planning tool is needed that takes into consideration such things as changing productivity levels and conditions as manhour requirements for different work areas are planned, rather than blindly allocated through traditional staffing modes.

Jan 1, 1995

By Lawrence Devon Smith

"The concept of risk is well established in the mining industry. It is acknowledged when estimates of reserves are expressed as proven or probable, when mining and metallurgical recoveries are applied to the ore, and when contingencies are added to costs. However, it is difficult to provide a quantitative assessment of risk. The significant sources of risk in a mineral project and how these are addressed in project evaluations are discussed.The discount rate is examined as a fundamental means of reflecting risk in discounted cash flow evaluations. Current industry practice is discussed, and a methodology for the analysis of risk levels is proposed that assesses the constituent components of the discount rate: real interest, mineral project risks, and country risk.IntroductionThis paper examines the components of the discounted cash flow discount rate and proposes a method of estimating project-specific discount rates. The motivation for this work comes from experience of project evaluations in which owners and purchasers had agreed on virtually every aspect of the evaluation except how much the project was worth. Agreement was reached on reserves, grade, recovery, capital costs, operating costs, taxes, and, by combining these components, even on the final cash flow values. The only difference in opinion concerned the discount rate to be used in the calculation of the net present value. Depending on the life of the project, such differences of opinion can cause a variation of more than 50% in the value placed on a project! This is illustrated in Figure I."

Jan 1, 1995

By W. Gutmannsbauer

Thin films of TiO2 nanoparticles have been prepared by different reactive deposition methods, such as electron evaporation, ion plating and ion beam sputtering. Many properties especially the optical properties, are strongly related to the film morphology and surface roughness. Scanning force microscopy was employed to obtain information on the surface structure of as-deposited Ti(h thin films. The influence of the deposition conditions and the film thickness on the optical and structural properties has been investigated. The as-deposited films were found to be amorphous or polycrystalline with anatase structure.

Jan 1, 1995

By Charles V. Jude

This U.S. Bureau of Mines report presents a review and evaluation of existing and new backfilling materials and methods for their applicability to the problem of gate road stress reduction in deep retreat longwall coal mines. Candidate backfill materials include pulverized coal combustion fly ash, flue gas desulfurization, and fluidized bed combustion by-products from coal-fired electric power generation plants. Properties of both backfill and its component materials are presented, with particular emphasis on the unconfined compressive strength and elastic modulus of backfill mixtures. Hydraulic mix designs discussed in this report include high-water content slurry and low-water content paste fills. Three gate road stress-transfer-modification concepts are proposed to reduce abutment stresses in gate road systems. The first concept, packwalling, involves packwall construction behind the headgate shield inby the face and adjacent to the headgate pillars. The second concept, gob-filling, involves infilling a strip of gob inset from and parallel to the headgate using paste injection methods patterned after a technology recently developed in Europe. In the third concept, entry-filling, slurry fill methods are used to fill abandoned gate roads and crosscut entries inby the face.

Jan 1, 1995

By Gaballah Djona M.

Spent hydrorefining catalysts contain about 5 % of CoO and/or NiO, 12 % of MoO3 and up to 10 % of V205. They are generally supported by alumina and contain up to 25 percent of C, S and hydrocarbons. Such materials are potentially hazardous to the soil and to water resources. Selective chlorination of raw unroasted samples with Cl2 + air gas mixture had been investigated. At temperatures lower than 600 °C, it was possible to recover more than 90 % of nickel and cobalt chlorides, about 99 % of the molybdenum and up to 75 % of vanadium chlorinated compounds. CoCl2 and Ni/Cl2 were extracted from the chlorination residues by their dissolution with acidified water. Molybdenum and vanadium chlorinated compounds were recovered by selective condensation from the vapor phase. The chlorination of Al2O3 could be limited to less than 6 %. The scale up of this treatment was successful and a flow-sheet is proposed.

Jan 1, 1995

By Aitchison J, Clarke G

A reappraisal of the stratigraphy, new regional kinematic analysis and thermobarometric data allow a new interpretation of the metamorphic zoning and tectonic structure of the Upper Eocene high-pressure metamorphic core complex of northern New Caledonia allow a three steps evolution to be proposed : 1) subduction and understacking of previously thinned continental crust elements; 2) subduction blocking due to the crustal thickening; 3) crustal thinning and extensional detachment during the diapir-like uplift and unroofing of the eclogitic core. Steps 2 and 3 may be partly contemporaneous. Such a model accounts for the thermobarometric and radiochronologic data, and also for the weakness of substratum deformation during the emplacement of the ophiolitic nappe.

Jan 1, 1995

Overland conveyor belts that exhibit tracking problems under loaded and unloaded conditions can be tested to' determine the root cause of the mistracking. Moveable conveyors are more prone to mistracking due to structure alignment requirements. In addition, belting quality, splice straightness and carcass condition has a dramatic effect on the performance of a belt in relation to tracking. Methods are discussed that are proven to reduce belt mistracking and improve the operational reliability of the conveyor system.

Jan 1, 1995

By Oliver Gutsche

High-pressure roll mill comminution of heterogeneous multicomponent feeds was simulated with artificial limestone-quartzite mixtures using a piston-die press. The influence of heterogeneous interactions between components of the mixture on grinding path, energy utilization and energy split have been examined. Primary fractures are governed by differential fracture strength and attrition resistance of the components at heterogeneous contacts; subsequent secondary and tertiary fracture events are governed by coarse-fine interactions in the particle-bed. The weaker component is preferentially ground out of the feed size fraction and concentrates in the fines. Energy split among the components in the mixture is a function of their relative fracture strengths. It doubles for limestone and decreases by a factor of 5 for quartzite over the entire range of the mixing ratio.

Jan 1, 1995

By G J. Corbett, T M. Leach

Although hosted within an Ordovician magmatic arc, the Peak Hill high sulphidation system displays features typical of youngerPacific Rim high sulphidation epithermal gold deposits. Regional NW trending transfer structures are inferred to localise the magmatic source at their intersection of the NS trending arc. Fluids have migrated from the magmatic source along NW structures and thence exploited permeable horizons, which have become silicified. Alteration displays typical zonation from silicification through assemblages characterised by alunite, pyrophyllite and kaolinite and is followed by breccia/fracture controlled sulphide and gold deposition. Sinistral rotation on the NS arc has dilated NW trending fractures to produce the WNW to EW dilational fractures which host the higher grade ore. Mineral assemblages are typical of formation distal to the magmatic source in an epithermal environment. The combination of alteration and mineralisation zonation with structure provide fluid vectors which target a magmatic source to the SE of Peak Hill.

Jan 1, 1995