Search Documents

By D. R. Tesarik, F. M. Jones, J. B. Seymour

As part of safety and stability studies at three underground mines in the United States, researchers installed earth pressure cells and embedment strain gauges in cemented rockfill to measure stress and strain changes as mining progressed and the rockfill was loaded. Data from these instruments were used to calculate the in situ modulus of the rockfill for two of the mines. A three-dimensional numerical model of a cemented rockfill cap was validated with data from extensometers anchored in the mine roof and sill; this model was then used to estimate deformation modulus at the third mine because the earth pressure cells and embedment strain gauges recorded negligible changes. Rockfill binder used at these mines ranged from 4 to 8 per cent of the dry components by weight, the water-to-cement ratio was from 0.42 to1.0, and the largest aggregate size in the three mixes ranged from 5 to12 cm (2 to 4.7 in). The range of the calculated in situ deformation modulus values was large, but as expected, it was bracketed by modulus values for cemented tailings and roller-compacted concrete with similar cement contents and water-to-cement ratios. Dans le cadre d’études sur la sécurité et la stabilité de trois mines souterraines situées aux États-Unis, les chercheurs ont installé des palpeurs de pression des terres et des extensomètres d’encastrement dans les remblais cimentés afin de mesurer les variations relatives à l’effort et à la déformation des terrains durant l’exploitation minière et le chargement du remblai. Les données recueillies à l’aide de ces instruments ont servi au calcul du module in situ du remblai dans deux de ces mines. Le modèle numérique tridimensionnel de la semelle d’un remblai cimenté a été validé à partir des données recueillies par les extensomètres ancrés dans la voûte et dans la semelle de ces mines; ce modèle a ensuite été utilisé pour estimer le module de déformation à la troisième mine, étant donné que les palpeurs de pression des terres et les tensiomètres enfouis avaient relevés des variations négligeables. La matière d’agrégation de l’enrochement utilisée dans ces mines comportait entre 4 % et 8 % des composantes sèches par poids; le rapport eau-ciment se situait entre 0,42 et 1,0; et la taille des agrégats les plus gros dans ces trois mélanges était de 5 cm à 12 cm (2 po à 4,7 po). L’écart entre les valeurs calculées des modules de déformation in situ était grand, mais comme on s’y attendait, cet écart a été compensé par les valeurs modulaires des résidus cimentés et du béton tassé au rouleau avec des teneurs en ciment et des rapports eau-ciment semblables. Als Teil der Sicherheits- und Stabilitätsstudien an drei Bergwerken in den Vereinigten Staaten von Amerika installierten Forscher Erddruckgeber und Einbindungsdehnungsmesser in zementierter Steinschüttung, um Spannungs- und Dehnungsveränderungen während der fortlaufenden Bergarbeiten und der Belastung der Steinschüttung zu messen. Daten von diesen Instrumenten wurden dazu verwendet, das In-Situ-Modul der Steinschüt-ung für zwei Gruben zu berechnen. Ein dreidimensionales numerisches Modell einer zementierten Steinschüttungsschwelle wurde mit den Daten von den im Grubendach und in der Schwelle verankerten Extensometern validiert; dieses Modell wurde dann dazu eingesetzt, um das Deformationsmodul in der dritten Grube zu schätzen, da die Erddruckgeber und Einbindungsdehnungsmesser nur geringfügige Messabweichungen feststellten. Das in diesen Gruben verwendete Steinschüttungsbindemittel variierte zwischen vier und acht Prozent an Trockenkomponenten nach Gewicht, der Wasser-Zementfaktor betrug zwischen 0,42 und 1,0 und die größte Zuschlagstoff-größe in den drei Mischungen schwankte zwischen fünf und zwölf Zentimetern. Die Reichweite der berechneten Werte des In-Situ-Deformationsmoduls fiel etwas breit aus, aber es fand erwartungsgemäß eine Klammerung der Modulwerte zwischen den Zemen-trückständen und dem durch Walzen verdichteten Beton mit ähnlichem Zementanteil und Wasser-Zementfaktor statt.

Jan 1, 2003

By S. Jeon, J. Kim, H. Lee

Though the importance of the engineering rock mass properties such as deformation modulus, cohesion and friction angle is emphasized, the researches on the reliability of these values are rarely performed. By using modified Takagi-Sugeno (TS) fuzzy inference system, a fuzzy model was developed based on the data obtained from domestic tunnel construction sites, and the ability of prediction was compared with the empirical equations conveniently used for estimating these values, which finds that fuzzy model is better than empirical equation. Sufficiently large database, however, is required for training the fuzzy model for more accurate prediction. Obwohl die Wichtigkeit der technischen Eigentümer der Felsenmassen wie zum Beispiel Verformungsmodulus, Bindekraft und Reibungswinkel betont werden, wird die Forschung auf der Zuverläßigkeit dieser Werte selten durchgeführt. Mit modifiziertem Takagi Sugenos (TS) Flaumigenschlußsystem wird die Flaumigenmodelle von den Daten, die von inländischen Tunnelbaustellen erhalten werden, entwickelt. Zum Schätzen dieser Werte ist es viel günstig, Flaumigenmodell zu benutzen, als zu adoptieren die empirische Gleichung für die Fähigkeit der Voraussage. Genügende große Datenbank wird aber zum Ausbilden flaumigen Modells für genauere Voraussage erfordert. Quoique l'importance sur la caractéristique d'ingénierie de la masse de roche comme le module de déformation, la cohésion et l'angle de friction, soit soulignée, la recherche sur la confiance de ces valeurs est rarement effectuée. Avec le système modifié de Takagi-Sugeno(TS) fuzzy inférence, le nouveau modèle fuzzy s'est développé. Après avoir estimé sa valeur, nous pouvons savoir que ce modèle fuzzy, basé sur les données venant du chantier de construction de tunnel national, est mieux que l'équaton empirique. Pourtant plus de données de base sont indispensables pour produire le modèle fuzzy plus précis.

Jan 1, 2003

By M. Pelser, C Aldrich

"The presence of calcium and magnesium in the hydrometallurgical processing of base metals, results in a number of process difficulties. These problems range from the contamination of the final product (where the final product is a precipitate) to high energy consumptions and large bleed streams during electrowinning. Calcium poses an additional problem in sulphate solutions owing to the low solubility of its sulphate salts. This can easily lead to a process stream that is supersaturated with calcium sulphate, resulting in unwanted solids formation within the process equipment.Several processes are reviewed for the control of calcium and magnesium. Of these, fluoride precipitation was selected for experimental investigation. This method involves the addition of a soluble fluoride to precipitate CaF2 and MgF2. The experiments showed high selectivity for calcium and magnesium over the base metals. The experiments also showed magnesium precipitation to dominate for calcium to magnesium molar ratios greater than 1:3.To avoid the domination of magnesium precipitation, a flow sheet is proposed whereby only a portion of the base metal stream is subjected to fluoride precipitation. For the precipitation, a 10% excess of ammonium fluoride is used to remove the maximum amount of calcium and magnesium. After precipitation and solid-liquid separation the split-stream is returned to reduce the overall calcium and magnesium concentration of the base metal stream."

Jan 1, 2003

By Ian M. Ritchie

Right across the universities of the developed world, the traditional disciplines of physics and chemistry are losing ground. Extractive metallurgy, which depends so heavily on chemistry, is also contracting despite a clear need for people with this kind of training in the mining industry. Reasons for this loss of popularity are discussed in this paper. High on the list is one of image. The extraction of metals is widely seen as a dirty, polluting, sunset industry which involves working in remote and uncomfortable corners of the earth for inadequate compensation. Ways in which the image problem can be overcome are considered. It is concluded that a concerted effort needs to be made by the universities and industry to redress this situation. The importance of extractive metallurgy, both now and in the future, when a greater emphasis will be placed on sustainability and recycling, needs to be stressed. In addition, courses need to incorporate training for a career path that leads on beyond extractive metallurgy.

Jan 1, 2003

Geological maps, data, and prospectivity analysis relevant to mineral exploration in New Zealand have recently been released. Regional-scale geological mapping is increasingly available for the country through the QMAP 1:250 000 Geological Map of New Zealand programme. Published QMAP sheets Greymouth, Wakatipu, Waitaki and Dunedin cover large areas of interest for mineral exploration companies. The QMAP geological data are also available in digital form for use with other digital datasets using GIS software. Crown Minerals, in cooperation with GNS, have completed two gold prospectivity studies; the first covering mesothermal gold in the South Island, and the second encompassing epithermal gold in northern New Zealand. These studies have defined areas of interest for these two mineralisation types and assembled geological, mineral occurrence and production, geochemical, geophysical, topographic and cultural data into projects for use with GIS software. Included are the results of prospectivity modeling for gold using these data and specific mineralisation models. The prospectivity studies and relevant data are freely available on CD through Crown Minerals and are intended to encourage mineral exploration in New Zealand.

Jan 1, 2003

Council for 2002/2003 President S.J. Ramokgopa President-elect T.R. Stacey Vice-presidents Senior F.M.G. Egerton Junior W.H. van Niekerk Immediate Past-president A.A.B. Douglas Honorary Treasurer J.A. Cruise

Jan 1, 2003

By J Thoma, W Skinner, W Stewart, R Smart

The acid neutralisation capacity (ANC) of rock sample containing significant iron carbonates and/or reactive framboidal pyrite can be a difficult parameter to determine. Results indicated that negative ANC results can occur if reactive sulfide minerals are present; and an over-estimation of ANC will result if significant Fe rich carbonate minerals are present during industry standard ANC tests. In this paper we investigate these problems. Results showed that a significant lag period may be needed (up to 432 hours) after standard Sobek ANC type tests of siderite for the complete hydrolysis of iron released from this mineral. This even occurred with standard industry modifications that included the addition of two drops of hydrogen peroxide. In this work we use a modified Sobek test that included filtering, and thence continued hydrogen peroxide addition until there was no subsequent pH drop, followed by back titration to pH 7.0. Results indicated that the ANC for the siderite (after zero hours) was immediately comparable to the ANC determined after 432 hours lag by standard Sobek type tests; and a calculated theoretical carbonate ANC. Investigations of coal waste samples containing significant framboidal pyrite indicated that standard Sobek ANC type tests can result in negative ANC values due to the oxidation of this reactive pyrite. Because sulfide acidity is already addressed by the MPA calculation, the inclusion of sulfide acidity as part of the ANC determination is effectively biased towards acid generation and thus positive NAPP values. Negative ANC values cannot be ignored or assumed to be zero as this masks any actual ANC available within the sample, which may possibly affect AMD categorisation. This sulfide acidity can be factored out using the quantity of S in the ANC digestion liquor and knowing the non-acid generating sulfate content of the sample prior to ANC testing. Results indicated that incomplete iron hydrolysis at the completion of the Modified Sobek ANC test is not only a function of iron carbonate dissolution, but is also related to the dissolution of Fe-sulfate salts, and the oxidation of reactive sulfides such as framboidal pyrite.

Jan 1, 2003

By D R. Carr

The installation of the Flotation Capacity Project flow sheet in the copper concentrator at Mount Isa Mines Limited has recently been completed. The project involved increasing the flotation capacity with Wemco tank cells and Jameson cells as well as changing the copper cleaner circuit layout. The engineering design and construction for the brownfield expansion had significant involvement from operational, maintenance and technical personnel adopting the same approach as the highly successful George Fisher project in the Lead/Zinc Concentrator at MIM. The involvement of people familiar with the concentrator allowed for smooth integration of the changes into an operating concentrator with minimal downtime. Detailed circuit analysis over many years identified opportunities for improvements in the flotation circuit for both grade and recovery. This paper describes the program of work that led to the Copper Concentrator Flotation Capacity Project, and the implementation of the circuit expansion and flow sheet changes that resulted in an overall improvement in the circuit recovery.

Jan 1, 2003

By J G. Webster-Brown, K L. Brown

The Waihi Region is host to many low sulphidation epithermal Au-Ag deposits. The Golden Cross mine located at the head of the Waitekauri River, eight kilometres NW of Waihi, was a gold mining operation that placed significant emphasis on environmental management. An assessment of the influence of this mining project on stream sediment geochemistry (Fe, Mn, As, Cu, Pb, Zn, Cr, Cd, Ni, Ag and Se) in the Waitekauri Catchment has been made. Effective waste management during the mine operation appears to have prevented contamination of stream sediment. Trace metal concentrations in the Waitekauri Catchment sediment have generally decreased since 1987, and are currently mainly below the ANZECC (2000) sediment quality guidelines. However, elevated As levels were recorded in the Upper Waitekauri River and Battery Stream, exceeding guideline values. Elevated levels of Cu, Pb, Zn and Cd were found in the Huanui Stream, a tributary of the lower Waitekauri River. This reflects the influence of past mining operations in the valley, as well as natural weathering of hydrothermally altered Coromandel Group andesite. At a number of sites, Mn concentrations also exceeded sediment quality guidelines, and this may be derived from the remediated Golden Cross mine site.

Jan 1, 2003

By L M. Foster, J R. Kellett, G A. McMah

The Great Artesian Basin (GAB) contains one of the largest reserves of fresh water in the world. The volume in storage is enormous, being estimated at nearly 65 000 million megalitres (ML). Development of this resource, dominantly for the pastoral industry, began in the late-1800s and quickly accelerated. With exploitation of the resource, artesian pressures declined almost as rapidly. This loss of head is a result of the total discharge from the basin and much of this discharge is waste of water. The waste through uncontrolled bores and inefficient distribution systems still amounts to about 75 per cent of all discharge. However, the volume in storage has hardly been depleted. The major concern is the effect of withdrawal on artesian pressures. Due to the size of the Basin, the relatively flat gradients and low permeability, the movement of water through the aquifers is extremely slow and independent of recharge. Hence, the normal concepts of sustainable yield (ie discharge should equal recharge) cannot be applied to the Basin as a whole as travel times do not allow for the effect of recharge to be seen away from the outcrop areas within management timeframes. The large volume in storage, though, can provide an extensive buffer to the impacts of temporary water needs. This effect should be considered when assessing the acceptability of fixed life projects such as mines and the extracted volumes from their operations. Identifying a sustainable yield involves balancing the acceptability of the economic, environmental and social costs with the associated discharge and fall in head, to arrive at an acceptable balance.

Jan 1, 2003

By P. A. Riveros, W. D. Gould, R. Molnar, D. W. Koren, P. Bédard

This paper reports the results of the field demonstration campaign of a new process for removing and destroying ammonia from mining/ metallurgical effluent solutions. The 50-day campaign was carried out at a uranium plant in Saskatchewan, Canada. The process was developed by adapting and integrating two well established technologies: zeolite adsorption/ elution to extract the ammonia from the effluent stream and to produce a concentrated ammonia eluate; and conversion of the ammonia in the eluate to innocuous nitrogen by applying bacterial nitrification-denitrification (NH3 = > NO3 - => N2). The data show that reasonable target criteria were met, under very challenging operating conditions. Problem areas and possible causes for poor performance are identified. Preliminary and generic cost estimates of the process are also presented.

Jan 1, 2003

By C. P. Manning

This paper reports recent progress in the development of a unique metal extraction technology utilizing zirconia-based inert anodes for the electrolytic reduction of metals from their oxides. In this process, the target metal oxide is dissolved in an ionically conducting liquid solvent phase. An extended anode consisting of an oxygen-ion-conducting stabilized zirconia membrane in intimate contact with a catalytically active electronic phase and an inert electronically conducting cathode are inserted into the molten flux containing the oxide. When the appropriate electric potential is applied between the electrodes the target metal is reduced at the cathode and oxygen ions are selectively transported across the stabilized zirconia membrane and oxidized at the anode. When the process is conducted at temperatures between 1200-1400°C, the ohmic resistance drop across the stabilized zirconia membrane is low, and high current densities on the order of I A/cm2 or greater can be obtained. In addition, the process efficiency can be increased further by directly reforming hydrocarbon fuel over the anode. Laboratory experiments at Boston University have demonstrated the technical viability of employing zirconia-based inert anodes for environmentally sound production of metals such as magnesium, tantalum, aluminum, etc., directly from their oxides. Significant progress has been made in the application of this concept to the electrolytic reduction of magnesium at 1300°C. The research topics covered include stability of the zirconia membrane in the selected molten solvent (flux), volatility of the flux, electrochemical characterization of the electrolytic cell, and analysis of the metals produced.

Jan 1, 2003

By J. N. Van der Merwe

The data base of failed coal pillars in South Africa was analysed with regard to the time of failure in an effort to develop a method to predict how long after their formation coal pillars will fail. It was found that meaningful results could only be obtained by splitting the data base up into groups that displayed similar behaviour. It was postulated, based on observation and experience, that coal pillars fail by a process of progressive weakening progressing into the pillar from the edges. Minimum pillar dimensions to ensure failure were calculated?these were the dimensions that corresponded to a minimum ?real? factor of safety. From the scaling distance required to reach the minimum safety factor, rates of scaling for the failed pillars were calculated based on the observed real lives of the pillars. It was found that the rates of scaling were unique for different mining areas and that they correlated directly with mining height and inversely with time. Using the derived scaling rates, the predicted pillar lives were back calculated for the pillars in the data base of failed pillars. In two of the three groups, the predicted lives correlated well with the observed lives on a one-to-one comparison. In all cases, the predicted lives were in the same time range as the observed lives. Overall, the frequency of predicted lives closely replicated the observed frequency of observed lives of the pillars in the data base of failed pillars. The method was successful in distinguishing between the data base of failed and a representative sample of intact pillars. While the predictions matched the observed lives of failed pillars, the predictions of expected lives for intact (hitherto unfailed) pillars were orders of magnitude greater. It is now possible to estimate the frequencies of future pillar failures for the purposes of mine closure and undermining of surface structures within broad bands.

Jan 1, 2003

By B Clemen, D Gordon, F Cesnik, P Griffin

In March 2002 Newcrest Mining Ltd commissioned a 4 Mtpa gold-copper concentrator at its Cadia Valley Operations in New South Wales. This paper presents the design and construction considerations, commissioning and ramp up issues related to start up of the concentrator as well as current performance and future expansion plans. Commissioning of the plant was the culmination of six years of project planning, from discovery of the resource during the Cadia Hill drill out campaign in November 1996 to project implementation and plant operation. Current resource estimates stand at around 50 Mt with an average grade of 2.4 g/t gold and 0.8 per cent copper. At current processing rates the project life is expected to exceed ten years. The processing plant comprises a 9.75 m (32 ft) diameter Fully Autogenous (AG) mill, a single 6.7 m (22 ft) diameter ball mill, pebble crushers, gravity gold recovery circuit and flotation plant. Upgrades to the existing infrastructure and manning requirements at Cadia will be discussed as well as the resultant impacts on operating costs for the operation. The processing plant was expected to deliver 290 000 ounces of gold and 30 000 tonnes of copper in concentrate in its first full year of operation and progress against that goal will be presented.

Jan 1, 2003

By Michael Zinigrad

The quality of metallic materials depends on their composition and structure and these are determined by various physico-chemical and technological factors. To effectively prepare materials with required composition, structure and properties it is necessary to carry out a research in two parallel directions: Comprehensive analysis of thennodynamics, kineties and mechanisms of the processes taking place at the solid-liquid-gaseous phase interface during welding processes and development of mathematical models of the specific welding technologies. We have developed unique method of mathematical modeling of phase interaction at high temperatures. This method allows us to build models taking into account the thennodynamic characteristics of the processes, the influence of the initial composition and temperature on the equilibrium state of the reactions, the kinetics of heterogeneous processes, the influence of the temperature, composition, hydrodynamic and thennal factors on the velocity of the chemical and diffusion processes. The model can be implemented in the optimization of various technological processes in welding, surfacing, casting as well as in manufacturing of steels and non-ferrous alloys, materials refining, alloying with special additives, removing of non-metallic inclusions.

Jan 1, 2003

By A. Peake

Background The CSIR Division of Mining Technology assumed responsibility for the operations of the Hoist Rope and Mechanical Test Laboratories at Cottesloe in April 1999. The laboratories were previously the responsibility of the CSIR’s Division of Manufacturing and Materials Technology, before which they fell under the National Mechanical Engineering Research Institute (also of CSIR). As the focus of this conference is on safety in mines research institutes, it was thought appropriate that this paper should review some of the activities at Cottesloe and its role in supporting mine safety strategies.

Jan 1, 2003

By D. Keech

The Conveyor Equipment Manufacturers Association (CEMA) specification B105.1 “Welded Steel Conveyor Pulleys” adequately defines standard pulleys for most aggregate material handling applications. However, many aggregate applications demand pulleys of higher capacity and reliability than that offered by CEMA pulleys. This paper examines the CEMA Pulley Standard and pulley specifications for aggregate applications requiring greater capacity and reliability than the CEMA Pulley Standard. Higher reliability increases the uptime and has a lower total cost of ownership.

Jan 1, 2003

By R. A. Bergman

"Process descriptions are provided for the following ten plants that treat high-magnesia lateritic nickel ores (saprolite) by pyrometallurgical means: PT Aneka Tambang; Cerro Matoso S.A.; Falconbridge Dominicana C. por A.; Hyuga Smelting Company Ltd.; Larco (Societé Minière & Métallurgique de Larymna); Loma de Niquel; Le Nickel, SLN-Eramet; Nippon Yakin Kogyo Company Ltd.; Pacific Metals Company Ltd.; and PT Inco Indonesia.Flowsheets, equipment information,chemistry and production data have been compiledfor plants based on both information providedby the companies and on calculated massand energy balances.IntroductionNickel is of vital importance to modern society. Without it, we would not be able to enjoy many of the things that we take for granted, such as computers, airplanes and stainless steel appliances in our homes and workplaces, to mention a few.Nickel occurs in nature both as sulphide and oxide ores. Approximately 36% of the nickel reserves in the Western World occur as sulphide and 64% as oxide ores. Sulphide ores respond to concentration processes, whereas, oxide ores do not. Sulphide ores mined at 1% nickel can be readily concentrated to 10% nickel, whereas, oxide ores cannot be concentrated and therefore have to be processed as mined.Laterite ores are normally classified intotwo groups:1. The high-magnesia ores, saprolites or serpentines, are, as a rule, processed by smelting. The main reason for this is that the nickel replaces magnesium in the magnesium-silicate lattice. To be able to recover nickel, the lattice has to be destroyed. This can be achieved by smelting under reducing conditions.Acid leaching is also possible, but in this case, large amounts of MgSO4 or MgCl2 will be produced making it costly to regenerate the acid.2. The high-iron, low-magnesia ores are known as limonite. The nickel is relatively loosely bonded to goethite and hence can be recovered by selective reduction followed by ammonium-ammonium carbonate leaching. In recently developed processes, these ores are also being extracted by acid pressure leaching, with high Ni and Co recoveries.This paper focusses on the production of ferronickel and nickel matte from the highmagnesia ores."

Jan 1, 2003

By C. E. Hales

In an effort to improve efficiencies and reduce costs, AngloGold has embarked on a process to develop and deliver consistent, high quality, tailings based support or construction products to stopes and tunnels on request. A three-phase approach of product conceptualisation, design and delivery has been adopted. To date a substantial amount of laboratory development has taken place with promising results, indicating that the project aims are achievable. Dans un effort pour améliorer le rendement et réduire les coûts, AngloGold s’est embarqué dans une opération qui vise à développer et fournir aux chantiers d’extraction et tunnels, sur demande, des produits de construction ou de support basés sur rejets qui sont réguliers et de haute qualité. Une méthode à trois volets a été adoptée : conception, création et livraison. A ce jour, un développement important en laboratoire s’est produit, avec des résultats pleins de promesses, qui semblent indiquer que les buts du projet peuvent être atteints. In der Bemühung, die Effizienz zu steigern und Kosten zu verringern, hat AngloGold begonnen ein Verfahren zu entwickeln welches auf Anfrage konsistent hochqualitative auf Haufwerk basierender Unterstützung oder Bauprodukte für Abbaustellen und Tunnels entwickelt und liefert Eine Dreiphasenplan zur Produktkonzeptualisierung, Design und Lieferung wurde adoptiert. Bis jetzt hat eine substantielle Anzahl an Laborentwicklung mit vielversprechenden Resultaten stattgefunden und aufgezeigt, daß die Projektziele erreichbar sind.

Jan 1, 2003

By George C. Webb

A wide variety and variable depth (up to 40 ft.) of compressible, uncontrolled fill (including construction debris and a perched water condition) was present at a proposed Kroger construction site in Dent, Ohio. An innovative solution using a combination of an ACIP foundation system with a Tensar geogrid reinforced load distribution platform was used to provide a high quality building pad. This system allowed the use of conventional shallow foundations for structure support. This system was used in lieu of more costly solutions, such as complete undercutting of the entire existing fill and replacement with engineered fill or a deep foundation/ structural slab system. The selected ground modification included a system of augercast piles bearing on shale bedrock, which were installed on a grid pattern over the entire building footprint. Then, three layers of Tensar polyproplene biaxial geogrid were used to create a reinforced soil mat, which was supported on the augercast piles. An eight-foot blanket of engineered fill was placed above the geogrid-reinforced mattress fill to establish the building subgrade elevation. Standard shallow footings and slab-on-grade construction methods were then used to support the 26-ft. tall masonry block building. A small-scale instrumentation program included monitoring the geogrid reinforced mat settlement, geogrid strain and earth pressure distribution under the reinforced mat to evaluate design assumptions and theoretical analyses. This case history describes the first application of a pile supported geogrid reinforced mat for structure support which has been documented in the United States.

Jan 1, 2003