Search Documents

By J. -C. Trickett

The high-resolution three-dimensional (3-D) seismic reflection data acquired for Impala Platinum between 1998 and 2002 in the western Bushveld Igneous Complex form an integral part of Impala?s mine planning and development programme. These data are of sufficiently high quality to provide unprecedented 3-D models of the geological structure of the Merensky Reef and UG2 Chromitite Reef, from which the mine deduces the size, geometry and distribution of mineable blocks. Conversely, the seismic data details zones of un-mineable ground caused by structural disturbances in the form of potholes, fault zones and pegmatoid intrusions. Furthermore, variations in dip and strike are well imaged, allowing the mine planners to optimize the mine design and layout. Current interpretation work is focused on enhancing the accuracy of these geological models even further through the analysis of ?seismic trace attributes.? Preliminary testing on the Impala Platinum 3-D seismic volume has shown that attribute analysis has the potential to illuminate a number of geological reef disturbances that are otherwise ?invisible? in the original seismic time volume. Potential areas of improvement include inter alia: ?Improved definition of major fault zones ?Improved definition of zones of reef depression (?slumping?) ?Identification of reef terracing and/or reverse dip. Keywords: 3-D reflection seismics; Impala Platinum Ltd; seismic attribute analysis; seismic micro technology (SMT); rock solid attributes; dip-azimuth; instantaneous phase and similarity.

Jan 1, 2005

By T. ?kre, O. M. Dotterud, S. Haarberg, J. Thonstad, G. M. Haarberg

An electrowinning pilot plant has been constructed at Falconbridge Nikkelverk A/S, Kristiansand, Norway. The equipment consists of a mixing tank where the electrolyte composition and temperature are controlled, an electrowinning tank equipped with five cathodes and six anodes of commercial size and design and a dechlorination facility. Electrowinning experiments were carried out in this pilot plant using acid cobalt chloride solution from the cobalt tankhouse. Key parameters were varied to obtain an improved understanding of the cobalt electrowinning process, focusing on the detrimental deposition of cobalt oxide on dimensionally stable anodes. The extent of anode scaling was found to be dependent on the electrowinning conditions. Low pH, temperature and cobalt concentration resulted in less scale being formed, however at the expense of cobalt current efficiency and cell voltage, adversely affecting electrowinning production capacity and energy consumption. When operating at high acidity, pH in the anolyte was higher than in the catholyte, which is believed to be due to H+ ions taking part in the current transport across the diaphragm, migrating out of the bags surrounding each anode.

Jan 1, 2005

By Andre Balt, Pierre Hofmeyr

It is only recently that automation has been applied to mining analytical laboratories. This paper describes the use of automation in the laboratory analytical process of hard-rock mining and geological samples and slurries in mining concentrator plant process control laboratories. Types of analysis include fire assay, XRF, ICP and wet chemistry. The benefits of automation are reduced unit cost of analyses, greatly reduced staff requirements, higher quality of data and very fast turn-around times.

Jan 1, 2005

By M. Mead, J. Dumouchel, W. Yule, J. Giroux

The QMM mineral sands of South East Madagascar contain approximately 1,900 million tonnes of mineable sand with a total heavy mineral (THM) content of roughly 4.5wt%. The QMM deposits are the world’s largest known reserves of 60% TiO2 ilmenite and also contain a small volume of zircon. The deposits are semi-continuous and homogenous and the mineralized sands are free flowing with minimal overburden, induration & slimes. These characteristics are favourable to dredge mining and allow the application of conventional wet gravity, electrostatic & magnetic separation to final products. A mature THM mineral suite of high valuable heavy minerals (VHM) content has enabled the development of a relatively simple separation process.

Jan 1, 2005

By Rudolph P. Frizzi

Structures supported on ACIP and DD piles perform successfully when quality control is maintained from the initial site subsurface investigation through pile design, bidding, and construction. The four stages of ACIP / DD pile construction are: preparation, augering the pile, grout / concrete placement, and reinforcement installation. During all four stages, careful observations and communication between the contractor and the owner's engineering inspection personnel are vital to successful pile completion. Automated monitoring equipment (AME) exists to supplement, but not replace, the field personnel's observations during the pile augering and grouting operations. Full-scale field load testing is done to verify the pile's geotechnical and structural design, and the contractor's pile installation means and methods, using several procedures including: conventional top loading, high-strain dynamic, rapid axial compression (i.e. Fundex PLT and Statnamic), and Osterberg Cell. Non-destructive sonic testing is performed to investigate the below-grade sectional properties of the completed pile; such methods include: low-strain impulse testing, and single-hole and cross-hole sonic logging. Post-construction observations are necessary to verify pile location and top properties prior to overlying cap construction.

Jan 1, 2005

By A. K. Dikshit, H. R. Murty, S. K. Gupta

This paper deals with the development of environment performance indicators (EPIs) for the steel industry. Environmental performance has become one of the key measures of business success. Emergence of continuing pressure from customers, employees, government and NGOs for environmental performance evaluation (EPE) of industries has led to evolve a framework for the development of sector specific environmental performance indicators. EPIs can be used by steel industry for assessing the continual improvement in environmental perfromance, selecting various eco-friendly options, benchmarking, environmental reporting, technology assessment and dissemination, evaluating environmental impacts and building EPIs based environmental management systems. The objective of this paper is to develop EPIs for steel industry and provide framework for development of environmental performance indicators based environmental management system and its integration with the overall management system. An indepth discussion has been presented concerning identification of EPIs, eavaluation of significance of EPIs, their prioritization and its integration with Environmental Management Systems. A new methodology has been proposed for implementing EPIs based environmental management systems . The material presented is derived in part from PhD studies of Rajesh Kumar Singh.

Jan 1, 2005

By R. L. Virta

Common clay is a natural, fine-grained material composed of hydrous aluminum silicates. Shale is a laminated sedimentary rock that is formed by the consolidation of clay, mud or silt. Production About 160 companies produced common clay and shale in 41 states. In states not reporting production, common clay and shale probably was mined and sold for construction applications by companies not participating in the U.S. Geological Survey’s canvass of producers.

Jan 1, 2005

By Paul Laframboise, Nigel MacDonald, Mike Hallewell, Robert Thorpe

"Galmoy Mine, owned by Arcon Mines Limited, has operated since 1997, and is one of three operating lead/zinc mines in Ireland. Changes in ore type starting in mid 2002 created challenges to metallurgical operations at Galmoy. This resulted in unacceptable lead and zinc flotation performance, which prompted initiation of a formal plant review and a subsequent stabilization programme. This involved a structured review of operational practices, development of a new Standard Operating Procedure (SOP) which in turn led to significant changes in process control equipment needs in conjunction with extension of zinc flotation cell residence time.This paper will describe the metallurgy of the Galmoy operation. Reasons for the poor metallurgy experienced in 2002 will be described, as well as the solutions identified to overcome these problems. By the second quarter of 2003, these solutions had been implemented and recoveries had risen to record levels.INTRODUCTIONGeneralGalmoy Concentrator is located in County Kilkenny (Refer to Figure 1 below) and was constructed during 1996 and commissioned in 1997.The concentrator at Galmoy had been designed initially to treat 650,000 tonnes per annum of primarily CW ore type. The main mineral of economic significance was sphalerite (Typically 10 to 11% Zn) with some minor galena (0.7%Pb) in a dolomite (Magnesium Carbonate) host rock.The only other competing sulphide mineral was pyrite (Circa 3 to 5% Fe in Mill Feed. This CW ore type predominated the first 6 years of production, but in August 2002, the ore mineralogy changed due to significantly higher levels of pyrite rich G ore body being blended in with CW ore."

Jan 1, 2005

By K. Poorhaydari, B. M. Patchett, D. G. Ivey

In this paper, some applications of carbon extraction replicas, as samples for transmission electron microscopy (TEM), are discussed. Modern high strength microalloyed (HSMA) steels, used as structural or pipeline materials, have very small grains with substructures. Replicas used in TEM can resolve the grain boundaries and can be used for grain size measurements in cases where the small size of the grains pushes the resolution of conventional optical microscopes. The grain size variations obtained from replicas correlated very well with mechanical property variations, indicated by hardness, in the fine-grained heat-affected zone and base metal of some welded HSMA steels. Replicas are also very suitable samples for precipitate examination with analytical TEM. Advantages and limitations of the application of replicas, as well as some corrections for the estimation of the volume fraction of fine precipitates, are discussed.

Jan 1, 2005

By K. Adham, C. Lee

The demand for nickel is continuing to exceed inventories, and producers are working vigorously to increase capacity. Many nickel processes utilize the fluidized bed technology for its fast heat and mass transfer, excellent temperature control and low maintenance. The following four nickel applications of the fluidized bed technology have been commercialized: I) Sulfide ore roasting; II) Nickel sulfide (matte) roasting; III) Nickel oxide reduction; IV) Nickel chloride pyrohydrolysis. This paper examines the issues surrounding the application of fluidization technology to the above processes, from the stand point of the engineer modeling the process and designing the key equipment, based on the historical success stories and the fundamental principles of flow sheet synthesis. Using the available data in open literature, typical flow diagrams (with convenient bases of 1 t/h feed or product) are developed to illustrate the relative flow rates and to highlight the key features of each application. In addition, some historical background information is provided for each process with supplemental notes with regards to our company's involvements.

Jan 1, 2005

By J. E. Amadi-Echendu, F. Stober, J. Ndlovu, L. R. Nelson

The Polokwane Smelter Complex (PSC) relies on a single 68MW high-intensity six-in-line furnace to smelt a planned 650 000 t/a dry concentrate to produce a platinum group metals (PGM)-bearing matte. As typical of a greenfields venture, considerable attention was paid to the project development and implementation stages of design, engineering, construction and commissioning. Somewhat unusual though, was the role of a dedicated multi-disciplinary "Operational Readiness" and support team, comprising the owners team and specialists from the furnace designer, HATCH, to effect a safe and rapid ramp-up to the design smelter capacity of 68MW. The challenges encountered in developing an effective partnership will be discussed. The modus operandi and roles of the "Operational Readiness" team during the design, procurement, construction and commissioning stages as well as that of the operational support team within the overall ramp-up objective will be presented. The "Operational Readiness" team was responsible for:

Jan 1, 2005

By Charles Dowding, Cathrine Aimone-Martin

This article summarizes an investigation of the structural response of a brick façade home in New Mexico. The subject Ricter residence was located some 1100 to 1400 ft away from an aggregate quarry, and was subjected to a maximum peak particle velocity and air blast over pressure of 0.29 ips and 122 dB, respectively. Superstructure (corner) and mid-wall responses to blasting and human induced activities were measured. An existing exterior crack in the brick work was instrumented to measure crack width response to blasting, human induced activities, and environmentally induced changes in temperature and humidity. Crack and structure response data were correlated with ground velocity and airblast excitations. Amplification of ground motions at the upper structure were calculated and compared with values for typical wood frame structures. The natural frequency and damping characteristics of the structure were determined to compare with measured amplification values. Wall strains produced by bending and inplane tension strains were computed from upper corner structure response and compared to failure strains for drywall and brick veneer. Calculated strains were found to be far lower than those required to crack brick and environmentally induced crack response was found to be far greater than that caused by blast induced ground motion or airblast overpressures

Jan 1, 2005

By I Jabou, D G. Blazak, L C. S Hogarth

The R70 test is a good indicator of coal reactivity to oxygen and is commonly used to provide a rating of propensity for self-heating. Tests performed by The University of Queensland Spontaneous Combustion Testing Laboratory have resulted in the development of a large database that shows the impact of coal quality on this parameter. From these results it is possible to infer an R70 value, which can be used to gain an appreciation of the intrinsic coal reactivity before it is even tested. However, any interpretation of R70 values must consider the influences of coal rank, mineral matter and moisture content to provide a better understanding of the spontaneous combustion risk of a particular coal.

Jan 1, 2005

By G. P. Gu, B. Fang, R. W. Revie, M. Elboujdaini

Stress-corrosion cracking (SCC) tests were conducted in the near-neutral pH standard solution, NS4, and in an actual soil solution, using four-point bending at high a stress ratio and low frequency conditions very similar to those of operational pipelines. Pitting incubation appeared first and then pitting initiated and grew in both solutions although there were many more pits on the specimen tested in soil purged with 5% CO2 + 95% N2 than in the specimen tested in NS4 solution purged with the same gas. These observations show that samples in soil solution are more susceptible to pitting than those in NS4 solution. When the pit reached a critical size, the increased stress concentration around the pits, resulted in the transition to a crack.

Jan 1, 2005

By M. Dupuis

It has been previously demonstrated [1,2] that using selective collector bar rodding has a big impact on the uniformity of the current density at the top surface of the cathode block and hence on the intensity of the horizontal current in the metal pad, The present study investigates the impact of using selective collector bar rodding on the MHD stability of a 500 kA aluminium electrolysis cell, For this purpose the recently developed MHD package for the aluminium reduction cell time dependent behavior is used.

Jan 1, 2005

By D. Want

In titanium-lined autoclave design the most critical point of its mechanical reliability is its titanium batten strips present at the circumferential and longitudinal barrel-weld seams. Recently an Australian Company, W.E. Smith Hudson (WESH) P/L, has developed a fully flush batten strip and is building autoclaves with this design. Significant research and development has been performed in the process. In this presentation, design aspects of these batten strips are presented that cover topics such as residual-stress magnitudes during fabrication, affect of preheat during batten-strip welding and residual stress in respect to fatigue life. There has been little research done regarding the affects of residual batten stress in relation to fatigue life. Considerations of this 'grey' area of design will be discussed based on the author's research data and finite element analysis.

Jan 1, 2005

By H. Abdollahi

Cold rolling is one of the most important techniques in metal forming since the cold rolling products are almost finished product, The product quality of this process is widely influenced by friction in the roll gap; therefore, controlling the friction and other parameters affecting the cold rolling is very important in order to have a product with high quality, Among the cold rolling parameters, the pressure distribution or friction hill within the roll gap is known as the most significant one, In this study, a new software (Matroll), is introduced which can determine the coefficient of friction (COF) and plot the friction hills for an industrial mill, Besides, based on rolling equations, it offers about 25 rolling parameters as outputs. To verify the software operation, the real industrial rolling data was used as inputs, The results (outputs) are in good agreements with the findings of other researchers, The COF values are very reasonable, The friction hill shows that COF is not constant over the whole arc of contact.

Jan 1, 2005

By B Mohanty, G Yamin

A number of parameters, aside from blast design and pre-existing rock conditions, can change the performance of the explosives system in actual blasting practice. Sympathetic pressures caused by detonation of preceding holes have been identified as a major contributor to explosive system malfunctions, leading to uneven blasting performance. These effects can occur both within a hole or across several holes. These can consist of high transient pressures related to the shock phase of the explosion or the relatively longer or quasi-static pressures associated with the explosion gas expansion phase. This study presents the findings from an on- going investigation on measurement and analysis of these pressures between donor and receptor holes in a granitic outcrop for representative inter-hole distances and borehole conditions, employing single cartridges of emulsion explosive in 45 mm diameter holes. The results, despite wide scatter in the measured values, show the very short duration pressures to range up to 7 MPa and arriving within a few milliseconds after detonation, whereas the much lower amplitude pressures arrive after tens of milliseconds. Both have the potential to seriously affect the performance of an explosives system.

Jan 1, 2005

Breaks in coal slurry impoundments can threaten the lives and health of area residents, destroy homes and businesses and contaminate water supplies. This dangerous potential looms over coalmining regions in West Virginia and throughout Appalachia. The Coal Impoundment Project was begun in June 2003 to provide an inventory and mapping of active and abandoned impoundments in West Virginia. The project also provides the public with specific information about the impoundments in their communities. It is dedicated to alerting residents of danger and evacuation plans, reducing risk to residents and finding alternatives to impoundments. Since its first year, more than 100 impoundment sites have been added to the project’s Website.

Jan 1, 2005

By F. Khomamizadeh

In this study, deep cryogenic treatment was applied to A319 cast aluminum samples. Although the cryogenic treatment didn't have any significant effect on mechanical properties of the well degassed and fluxed samples, but the tensile strength of the samples containing a considerable amount of gas and shrinkage defects was improved surprisingly, This improvement was attributed to the strengthening of the a-aluminum matrix which slows down the propagation of the existing defects. There was no significant increase in the hardness after cryogenic treatment, The abrasion resistance of the alloy was improved after cryogenic treatment, by developing a homogeneous protector shield, composed of abrasive grains penetrated into the soft aluminum matrix and kept tight.

Jan 1, 2005