Search Documents

By Dennis Molvik, Roberto J. Guardia, Brad Cowles, Rick Andrews, Robert A. Robinson

A 220-meter (m) segment of the Henderson/ ML King Combined Sewer Overflow(CSO) consists of two 1.8-meter-inside diameter (I.D.) pipe-jacked tunnels that pass beneath Interstate-5 and the BNSF and UPRR railroads. A seismic tomography survey was conducted to develop a 3-dimensional profile of the tunnel zone and better define potential obstructions. The tomography was conducted through three 11 cm high-density polyethylene (HDPE) pipes installed in a triangular pattern around the future tunnel alignments using horizontal directional drilling methods. The pipe-jacked tunnels have been successfully completed, thus permitting a comparison between the predicted obstructions and those actually encountered. The top HDPE tomography pipe was also used to monitor settlements with an experimental horizontal profiler above the advancing tunnels during construction and located two areas of ground loss beneath I-5 that were subsequently grouted.

Jan 1, 2005

By L. H. Shang

The 319 Al-Si alloy is one of the most prominently used aluminium-based alloys in motor vehicle and engine applications, Microporosity present in 319 alloy castings reduces the load bearing capacity of the castings, The quantitative prediction of microporosity levels in Al-Si castings has been a subject of much interest for several years. In this research a new criteria function, tf 1,98 R13° (tf: local solidification time, R: cooling rate) was developed by multiple regression analyses, correlating thermal data from simulation studies to experimentally obtained microporosity values. This new criteria function gives a general prediction of microporosity in 319 Al-Si castings.

Jan 1, 2005

By Conné Spangenberg

Contents ?Introduction ?Metal accounting environment ?Problem statement ?Investigations & Achievements ?Metal Accounting ?Principles ?Standards ?Audits ?Questions

Jan 1, 2005

By Minggao Qian, Jialin Xu, Wenqi Lai, Weibin Zhu

This article advances an innovative concept explaining the connotation and technical system of "green" mining. The important theoretical foundations of "green" mining are the distribution and development characteristics of joints, fractures and bed separations, and the seepage and flow behavior of methane and water in the broken rock strata following coal mining. The main focus of "green" mining technique includes water-preservation in mining areas, coal mining under buildings with bed separation spaces grouted to retard surface subsidence, partial extraction and backfill mining, simultaneous extraction of coal and coal-bed methane, coal roadway supporting and underground disposal of rock waste, underground coal gasification, etc.

Jan 1, 2005

By A. D. Dalvi

Economics, Resources, Environment and Technology are the major driving forces in the base metals industry. However, these factors are intertwined and together will propel the industry in the future. The demand for metals has grown with economic expansion, between 2 to 4 % p.a. The current growth cycle has been driven by economic expansion in China where the demand for base metals has risen from - 7 % of the world demand in the 90's to - 25 % of world demand today, and rising. Base metals are commodities and their demand and price are cyclical. Historically metal prices have declined in constant dollars, forcing the industry to reduce costs, increase productivity and increase the scale of operation for economies of scale. Due to resource depletion and capacity expansion the industry is driven to expand its reserve and resource base. However, in the case of sulphide deposits of copper and nickel it appears to be a losing battle. For nickel the laterites represent a vast source at this time. Their development requires development of new technologies to make these resources economic. Emission reduction is being increasingly mandated in most jurisdictions with all governments enacting progressively more stringent regulations. The industry has been responding with technological innovation. With the Kyoto protocol there is a push to reduce energy intensity in metal production. Technological innovation is driven by all the other factors and is leading to novel ways of doing exploration, mining and processing, that would maximize resource delineation and utilization, reduce costs, increase productivity, reduce energy consumption, maximize asset utilization and reduce environmental affects. Development of alternative technologies such as Pressure Acid Leach of laterite for nickel, bio-leaching, heap leaching, SX-EW etc are being adopted to achieve the aims of the industry.

Jan 1, 2005

By Polysius AG

"The Lone Tree demonstration was an important milestone in bringing High Pressure Grinding Roll (HPGR) technology into hard rock applications in the mining industry. HPGRs have become standard equipment in the cement, iron ore, and diamond industries over the past fifteen years, but their use in severe duties found in the hard rock mining sector has been restricted due to high roll wear and subsequent low availability. HPGR availability has historically been limited because of frequent downtime for edge weld rebuilding as the rolls wore and short tyre life from high roll surface wear rates.Recent advancements in HPGR wear protection are now being evaluated for commercial applications in the gold and copper mining industry where this technology may offer benefits in comminuting hard and/or abrasive ores and in improving metal recovery in heap leaching applications.Proving the feasibility of HPGRs for processing competent, abrasive gold ore, Newmont Mining Corporation, the world's largest gold producer, operated an HPGR demonstration plant employing a POLYSIUS (POLYCOM) HPGR incorporating some unique wear protection, at their Lone Tree gold mine near Winnemucca, Nevada. Results of the successful demonstration are presented and evaluated in this paper.The Lone Tree HPGR demonstration plant operated for three months, from April through June 2003. The HPGR operated for 1626 hours and processed 141,000 tons of ore. This technology demonstration focused on measuring operating performance, wear characteristics, and availability of today's HPGR technology.Polysius' innovative roll surface wear protection system eliminated edge-welding downtime. Improved surface wear protection extended tyre life to predicted durations acceptable for very abrasive service. The POLYCOM HPGR is now deemed suitable for selected hard rock applications."

Jan 1, 2005

By B Mennie, R Poedjono, G Coad

PT Freeport Indonesia operates a large copper and gold mining operation near Tembagapura, Papua (formerly, Irian Jaya), Indonesia. This is a remote location with its own set of unique operational characteristics. The mining and concentrating operations typically produce a concentrate containing 2500 tpd of copper and 6000 oz of gold per day from the combined mining of a 45 000 tpd (ore) block cave operation (DOZ Mine) and a 190 000 tpd (ore) open pit mining operation (Grasberg Open Pit). The Grasberg Open Pit mine will be exhausted in 2015 at which time FreeportÆs operations will entirely underground mining methods. The Common Infrastructure Project (CIP) incorporates the elements required for the shift to underground mining at a production rate approaching 200 000 tpd. The AB Adit portion of the CIP will provide deep level access to the Grasberg Block Cave (below the Open Pit), Kucing Liar, Big Gossan, and the Mill Level Zone orebodies. Commencement of the project was September 2003. The Grasberg Block Cave is planned to start production in 2014. This paper provides details on the project scope, innovative contractual framework, advancement of mining methods throughout the life of the operation, equipment selection, manpower selection, training, geological, and socio-political conditions related to the project.

Jan 1, 2005

By M. Bozorgtabar

Metal Matrix Composites (MMC) have a ductile matrix containing ceramic particles, Due to their improved wear properties, Al?SiC composites have economical applications in many industrial uses where wear is a problem, One of the most serious difficulties in manufacturing Al-SiC composites is obtaining adequate 'wetting' of the particles by the melt. In this research work, a stir casting system was designed for the improved manufacturing Al-SiC composites, The effect of some production variables such as the addition of SiC particles to the aluminum melt on wettability, was also studied. The results showed that the manual addition of particles would not be successful in manufacturing and that a system of adding silicon carbide particles through controlled temperature, atmosphere and improved mixing was needed.

Jan 1, 2005

By L. Kulik

Sustainability of lignite mining in the Rhenish lignite mining area is ensured by a preceding study of the overall project, with the involvement of all those affected. The supporting holistic consideration of the various sustainability elements is essential for a later balancing of the several ecological, economic and social concerns. In what follows, a brief overview of the Rhenish lignite mining area is given as introduction to the focus of this report, which is on sustainability, starting with the approval procedure under regional planning law incl. opencast mine planning, and extending to concrete on-the-spot implementation, taking the Garzweiler II follow-up mine as example. To illustrate the issues involved, an account is given of some selected sustainability elements.

Jan 1, 2005

By M. J. Merwin

Heat treated seamless tubular products are processed in a fashion that can be easily modified to produce dual phase microstructures, through the implementation of intercritical soaking prior to quenching. Dual phase steels are known to possess low yield strength compared to tensile strength. The steel line pipe market is interested in low yield-tensile ratio materials for application in reel barge pipe laying operations. In the current work compositions of commercially produced material already in use for the line pipe market were examined and dual phase microstructures were successfully developed. The microstructure and properties of the materials were found to be stable over the range of intercritical temperatures employed. Tempering temperature and, somewhat unexpectedly, small chemistry differences were found to have the largest influence on properties. Excellent toughness performance was observed in samples tempered at temperatures in excess of 550°C. Tempering in this temperature regime produced materials with strength suitable for application as API X60 line pipe. A difference in tensile strength between steels of similar chemistry was observed, and is not fully understood at this time. Welding performance was considered through simulation of three regions of the heat-affected zone. Neither intercritical temperature, nor tempering temperature, were found to have a significant influence on the heat-affected zone properties. The peak temperature achieved in the thermal cycle was the only significant factor. The hardness of the heat-affected zone was found to increase continuously with increasing peak temperature. While toughness was found to be low for both partially-transformed and coarse-grain heat-affected zones, the toughness of the fine-grained heat-affected zone was substantially better. Based on the results found in this laboratory study, a limited production trial is expected.

Jan 1, 2005

By Toshiaki Akahoshi

Keywords: Wasted catalyst, Hydrodesulfurization, Ammonium vanadate, Ammonium molyb-date, Hydrometallurgical process. The fundamental reactions have been investigated in order to develop a hydrometallurgical process for recovery of molybdenum and vanadium from wasted catalysts generated in the hy-drotreating desulfurization of heavy oil. The principal steps of the process are a mild oxidation roasting of the waste catalysts at temperature around 500°C, leaching of the target metal components with dilute ammoniacal aqueous leachates, selective precipitation of vanadic acid, and ammonium molybdate precipitation. The selective recovery of vanadium as vanadic acid is successfully performed using ammonium sulfate as a salting-out agent. Recovery of ammonium molybdate is based on large dependence of solubility of ammonium molybdate in ammoniacal solutions upon temperature and ammonium salt concentration. In this process, the solution after recovery of vanadium and molybdenum is recycled to the leaching stage of the roasted materials, and the ammonium salts in the process liquor is in the repeated use. Employment of am-moniacal system makes it possible to operate the roasting at much lower temperature than that for the currently operating process.

Jan 1, 2005

By Dale Bartholomae, David Harrison, Edward J. Walter

Methods that involve the use of signature blast holes in order to identify the particular frequency characteristics of a geographical area are widely available. Information acquired can be used to determine optimum blast hole timings to produce the desired constructive and destructive inference. However, these types of analyses can be both complicated and expensive. This study will investigate the use and practicality of signature hole and/or shift and sum analysis software and their application to small diameter construction utility blasting operations in Pennsylvania and faster moving projects in general. A determination will then be made as to whether this technology can be utilized by today’s blaster, from both a functional and a cost effective basis. Single hole blasts will be detonated on various smaller construction projects and will be monitored with an array of seismographs. The collected data will be analyzed in order to determine the optimum timing between holes to produce the preferred frequency content while keeping in mind the explosives user’s current inventory of blasting supplies.

Jan 1, 2005

In extracting base metals from orebodies, sulphide as well as oxide, the main environmental concern is sulphur, whether in the form of sulphurous gases or sulphate in liquid form. Generally sulphur is in over supply in developed countries mainly because of strict legislation to capture it. In developing countries, on the other hand there is usually a shortage of sulphur because of less strict environ-mental legislation. Africa falls in this second category and the African continent imports substantial amounts of sulphur, despite the fact that large quantities of sulphur are emitted by smelters, thermal power stations, coalmines, fertilizer manufacturers and others. Other than making acid from gaseous emissions, existing methods to capture sulphur from gaseous and liquid effluents are uneconomical and it ends up in the environment either as ammonium sulphate (from gaseous effluents) or as gypsum (from liquid effluents). The CSIR?s Environmentek and Key Structure Holdings have developed a process whereby gaseous sulphur emissions and sulphates in liquid effluents can be economically captured and converted into elemental sulphur and metal carbonates. The elemental sulphur is of high purity as it is precipitated from a gas stream and is readily marketable. The metal carbonates (barium or calcium) can be recycled back to the process or marketed. The only harmful by-product of the process is carbon dioxide. Should natural gas or methane be available, the carbon dioxide could be reduced by about one third. Should solar, wind or hydro energy be available to generate hydrogen, the carbon dioxide emissions would be zero. Employing this technology could make Africa independent of sulphur imports and furthermore reduce the impact of acid rain and seepage of sulphate from gypsum and other waste dumps into the environment.

Jan 1, 2005

By J. Pesl, R. Hurman Eric

Metal-slag phase compositions of molten iron and ilmenite smelting slags or solid titanate phases were determined between 1500° and 1700°C. The influence of oxygen partial pressure and impurity oxide additions including Al2O3, Cr2O3, MgO and SiO2 were investigated along with amount of reductant-carbon. The XRD revealed that the quenched slag crystallized as pseudobrookite (M3O5) solid solution in equilibrium with iron. Silica additions formed separate silicate phases because of its immiscibility in the titanate phase. Under strong reducing conditions iron oxide was almost completely reduced and the slag phase solidified as a consequence thereof. Cr2O3. SiO2 and MnO were also reduced to a high degree. Under weak reducing conditions the slag was fully molten and non of the impurity oxides were reduced. A significant portion of manganese, some magnesia and silicon, in the form of SiO gas, were removed via the gas phase due to their considerable vapour pressures. Alumina was not reduced under the applied conditions. A comparison of the experimental results with industrial data clearly suggested that industrial ilmenite smelting process operated under non-equilibrium conditions.

Jan 1, 2005

By B Firth, G OÆBrien, B Jenkins

In coal flotation, particles of different components of the coal such as maceral groups and mineral matter and their associations have different hydrophobicities and therefore different flotation responses. By using a new coal grain analysis method for characterising individual grains, more detailed flotation performance analysis and modelling approaches have been developed. The method involves the use of microscopic imaging techniques to obtain estimates of size, compositional and density information on individual grains of fine coal. The density and composition partitioning of coal processed through different flotation systems provides an avenue to pinpoint the actual cause of poor process performance so that corrective action may be initiated. The information on grain size, density and composition is being used as input data to develop more detailed flotation process models to provide better predictions of process performance for both mechanical and column flotation devices. A number of approaches may be taken to flotation modelling such as the probability approach and the kinetic model approach or a combination of the two. In the work reported here, a simple probability approach has been taken, which will be further refined in due course. The use of grain data to map the responses of different types of coal grains through various fine coal cleaning processes provided a more advanced diagnostic capability for fine coal cleaning circuits. This enabled flotation performance curves analogous to partition curves for density separators to be produced for flotation devices.

Jan 1, 2005

By Brett Zernich, Michael Krulc, Brett Robinson

This paper provides an account of the efforts undertaken to construct the Northeast Interceptor Sewer (NEIS) project, which is a portion of a much larger program in Los Angeles, California to upgrade the city’s wastewater facilities. The project consisted of a number of elements, including both soft ground and rock slurry wall shafts, drilled shafts, soft ground EPBM mining, rock TBM mining, large diameter pipe placement, and underground structure construction. The need to complete the project under strict schedule constraints, in addition to the challenges of underground construction in congested urban areas, necessitated the work be undertaken with the proper balance of state of the art equipment, and thoughtful planning. The paper will detail the means, methods, and equipment used on the project, as well as discuss several of the unforeseen conditions encountered during construction.

Jan 1, 2005

By M. Syamujulu

In 1994, Nkana smelter commissioned a multimillion US Dollar Chilean Teniente converter (CT) in its operations in order to improve its smelting technological base. The main objective was to reduce the overall smelting energy costs and increase the sulphur capture for sulphuric acid production to support the company?s leaching operations at Nchanga tailings leach plant. A decade of CT operations have since ensued following its installation and start-up. This paper provides a technical and operational audit of the performance of the CT in the first 10 years of its operations at Nkana smelter.

Jan 1, 2005

By Chaoxun Zhao, Daniel Tao, Craig Blue, Narendra B. Dahotre, Rick Honaker, Bhupendra K. Parekh, Hongyang Han

Equipment wear and corrosion have significant adverse impacts on the operating cost and efficiency of mineral processing plants. In this project advanced surface enhancement technologies are being investigated to decrease the wear and corrosion rate of metal surface. Enhanced metal surfaces are achieved through surface conversion, enrichment, and coating by use of advanced High-Density Infrared (HDI) and other technologies. Studies have been done to determine the effects of process parameters on surface properties and identify optimum conditions. The microstructure of the enhanced metal surfaces was characterized by SEM, EDS, and microindentation. Laboratory wear testing was carried out to investigate the wear performance and the viable coating candidate was determined.

Jan 1, 2005

By W. R. Tyson

Pipelines for the transport of gas and oil are being designed to operate at increasing pressures in increasingly harsh environments. The steel used to construct these pipelines must have adequate toughness to tolerate weld imperfections (i.e. withstand bending strains) and to arrest running cracks (i.e. to prevent propagation of axial fractures). The problems posed in specifying suitable toughness parameters and the approaches currently being used to measure them are discussed.

Jan 1, 2005

By Y. Huang

Corrosion of GaAs in aqueous electrolytes is a major limitation in implementing GaAs-based photoelectrochemical solar energy conversion systems, In this work, the corrosion behavior was investigated by electrochemical methods and surface analysis approaches, in both H2SO4 and NH3?H2O solutions, Open-circuit measurements showed that the cleaned GaAs surface was very sensitive to water/air, Impedance measurements for n-GaAs showed that an inductive loop only appeared at a high corrosion rate because a reaction intermediate is the oxidant for a further decomposition step in combination with chemical reaction with water, The results suggest that the same corrosion/decomposition mechanism occurred on n-GaAs in the two solutions, When the surface-hole concentration was low, the hole injection or generation process was the rate-determining step, At large reverse bias on n-GaAs, with high-hole concentration, the corrosion rate was limited by a Faradaic adsorption process, involving an adsorbed intermediate, The different surface compositions after corrosion in the two solutions can be explained by the dissolution of As(0), Further oxidation of As(0) to As(III) in NH3?H2O solution is still slow, as suggested from X-ray photoelectron spectroscopy (XPS) analysis,

Jan 1, 2005