Search Documents

By Ken Dyck Sr.

"Construction of the Cigar Lake uranium mine in northern Saskatchewan is well under way. Production is anticipated to begin in the first half of 2007. When in full production, the mine is projected to produce a net 18,000,000 pounds of U3O8 per annum from a high grade ore averaging approximately 20% U3O8.Water management was a major issue that required substantial effort in the Cigar Lake design. Not only is effluent quality controlled, a tight water balance to minimize effluent volume is also designed into processes in order to minimize environmental impact. This paper focuses on the water treatment process and water handling equipment, as well as the operating philosophies that will reduce fresh water consumption to a minimum. An overview of the mining and ore handling systems, as well as aspects of controlling water production from the ore formation and the mine development areas will also be discussed.INTRODUCTIONThe Cigar Lake ore body has proven and probable reserves that total 232 million pounds U3O8. Cigar Lake is the world’s largest undeveloped high-grade deposit. It is the second largest highgrade deposit surpassed only by the McArthur River deposit another Cameco - operated mine in the Saskatchewan Athabasca Basin. Cigar Lake is owned 50% by Cameco Corporation, 37% by AREVA (COGEMA Resources Inc.), 8% by Idemitsu Uranium Exploration Canada Ltd. and 5% by TEPCO Resources Inc. When production starts in 2007, ground ore slurry from Cigar Lake will be shipped to the McClean Lake mill (owned by AREVA) some 80 km away. All of the Cigar Lake uranium will be leached from the ore at McClean Lake. During initial production ramp up, all uranium will be processed at McClean Lake to yellow cake (uranium oxide). After the average production has exceeded a 10 million pound per year rate, Cigar Lake uranium will begin to flow from the McClean Lake Mill to the Rabbit Lake Mill. At this point, subject to regulatory approval, 57% of the Cigar Lake uranium, in a uranium rich solution, will be transported to Rabbit Lake mill (owned by Cameco) for purification to yellow cake. A complete summary of the flow of uranium from the Cigar Lake ore body through to product at both McClean Lake and Rabbit Lake can be found in a recent paper titled “The Cigar Lake Project – Mining, Ore Handling and Milling” in the March 2004 issue of the CIM Bulletin. The paper was written by C.R. Edwards."

Jan 1, 2006

By Sergio N. Monteiro

Polymeric composites reinforced with natural fibers are increasingly been used in several engineering applications, from automotive parts to building construction elements. In addition to the relatively low cost, the natural fibers are also appraised by their renewable and biodegradable characteristics. Fibers extracted from the crust of coconut fruits, also known as coir fibers have been investigated for a possible use in composite materials. In the present work, the coirfiber/polyester matrix interfacial strength was evaluated by means of pullout tests. The variation of the pullout tensile stress vs. the embedded coir fiber length permitted to determine the critical fiber length and, thus, to calculate the interfacial strength. Observations by SEM complemented the results from pullout tests, indicating that coir fibers have a potential for application aspolymeric composites that could replace conventional materials such as wooden and gypsumpanels.

Jan 1, 2006

By G. Velarde

This paper presents the metallurgical results of column and stockpile leach tests with forced aeration to determine the usefulness of this process in the operational leaching at Sociedad Minera Cerro Verde S.A.A. The evolution of the aeration system is presented and also an innovative solution developed to overcome forced aeration’s main problem, which is the early obstruction of the aeration pipes located at the base of the stockpile, causing a decrease in air and oxygen levels and therefore a reduction in the metallurgical benefits.

Jan 1, 2006

By F. Azgomi

A possible way to characterize (classify) frothers using gas holdup as a surrogate for bubble size was explored. Nine surfactants with a range in chemical structures were selected and tested in a bubble column instrumented to measure gas holdup and superficial gas velocity. A correlation between frother type and gas holdup was observed: for alcohols, gas holdup increases with hydrocarbon chain length and the effect is the same whether the chain is branched or straight; for polyglycols, gas holdup increased with number of propoxy groups. The ranking by gas holdup gave the same result as other frother characterization techniques.

Jan 1, 2006

By T. Plikas, L. Gunnewiek

Computational fluid dynamics (CFD) modeling was used to evaluate the performance and optimize the design of a potroom ventilation system in an aluminium smelter facility. The ventilation system must ensure the inflow of fresh air to the workplace by natural draft and the removal of heat and hazardous emissions generated from the pot cell process. A full-scale, three dimensional CFD model of the potroom was developed to predict the air temperature distribution and contaminant concentrations throughout the potroom for the purpose of verifying that the industrial workplace hygiene standards will be met by the proposed ventilation system design. The modeling work was used to optimize the size of the floor gratings around the pot cell and roof ventilator, as well as determine damper settings in the roof ventilator. The effects of outside air temperature and external wind on the performance of the ventilation system was evaluated to ensure the design performs adequately in response to seasonal variations in climatological conditions.

Jan 1, 2006

By P M. Bradbury

The nature of aggressive process chemical requirements typically in the Platinum Refinery Industries, lend themselves to the use of Polymer Composite Glass Reinforced plastics for pipework and other associated equipment in these types of Plants. This paper discusses the basic characteristics of a Polymer Composite glass reinforced piping system and gives sample examples of applications in current present day use.

Jan 1, 2006

By C. Hari Manoj Simha, J. Gholipour, M. J. Worswick

Due to the high pressures involved in the hydroforming process, friction and lubrication play an important role and can affect formability of the material. Tubes of A1Mg3.5Mn aluminum alloy, of 76.2 mm (3 inch) outside diameter and 2-mm thickness were considered in this study. Three kinds of lubricants, Al070, Hydrodraw711 and water, were applied to the tubes and tubes were hydroformed to burst in a square shape die cavity. The key process parameters were recorded during the tests. An in-house Gurson-Tvergaard-Needleman (GTN) damage-based material model, implemented in LS-DYNA, was used to model the process and predict the formability of this material. The applied axial loads and internal pressures recorded during the tests were used in the computations. The effect of different types of elements (solid and shell) with different constitutive models (von Mises and GTN models) in predicting the strain distribution is studied. The GTN damage-based material showed a good ability to capture necking and displacement histories in this process. Both predicted and measured results showed that the lubricant with lower coefficient of friction can effectively increase the comer expansion.

Jan 1, 2006

By Daniel Hauer

Blocking. (5) The “blocking” of boulders is a much cheaper way of breaking them up than “mud capping.” It should always be used in preference to that method except when too much time will be consumed by a crew of men waiting for the drilling to be done, as shown in example of cost No. 1, as given under “mud capping.” Under such circumstances the time consumed would be a greater cost to the contractor than the extra amount of dynamite. Then, too, on large thin boulders to drill one hole would result only in breaking the stone into such pieces as would again have to be broken; and the many holes might equal the cost of extra dynamite. Under such circumstances if method (6) cannot be used, “mud capping” will have to be resorted to, to do the work economically.

Jan 1, 2006

By S. Dixon

The Phelps Dodge - PD/PERI Heap2D Model is a phenomenological stockpile leaching model that has been used to investigate the best operating practices for leaching chalcocite. The model was used to investigate the interrelationships of raffinate application rate, aeration rate, raffinate iron grade, acid cures, lift height, crush size, bulk density, air injection spacing and raffinate drip emitter spacing.

Jan 1, 2006

By K. Getsos

Western Greece is a favorable site for exploration and discovery of oil fields. The most important potential source rocks seem to be all the rocks deposited before middle Jurassic under special circumstances, such as reducing conditions, which allowed preservation and maturation of the organic material. In general all the rocks of middle Jurassic to Paleogene are not favorite source rocks. The porosity type was studied on fifty samples using scanning electron microscopy (SEM). Potential reservoir rocks are the porous Paleogene wackestones-packstones with boring, channel and vuggy porosity type. Finally seal rocks are the impermeable mud-stones and wackestones of Jurassic, Cretaceous and Paleogene age. These rocks consist of micrite and whole sells of foraminiferas and the porosity type is mainly intercrystal/interparticle. A Total Organic Carbon (TOC) analysis, conducted on seventy samples using a wet oxidation method, has revealed an extremely low TOC content (less than 0.05 %). This amount is by far less than the minimum organic content amount, required for source rock characterization and characterizes all the rocks of middle Jurassic to Paleogene age. Additionally, 18O and 13C stable isotope analysis was contacted and the results are given in d values. All the rocks within the studied time interval have much lower d values than petroleum source rocks. Clay mineral content was studied in almost seventy samples. As is indicated by the clay mineral content the studied rocks have reached up to the Middle Diagenesis and the temperature during diagenesis was rather low.

Jan 1, 2006

Coal has been mined in the central Appalachian coalfields of southern West Virginia, western Virginia, and eastern Kentucky for more than a century. The dwindling reserve base consists in large part of coal that would have been considered unmineable by earlier generations. Nearly every current operation is working on a property where coal has been extracted in the past, from seams either above, below, or both. NIOSH is conducting research aimed at helping mine planners prevent hazardous conditions due to multiple seam interactions. To-date, more than 300 case histories have been collected from underground mines, mainly from central Appalachia. This paper focuses on several of the more challenging situations that have been encountered, including: • Room-and-pillar development 20 ft (6 m) beneath full extraction workings at a depth of 1,000 ft (300m) of cover (Virginia) • Pillar recovery 45 ft above full extraction workings at 900 ft (270 m) of cover (Virginia) • Near-simultaneous room-and-pillar mining with pillar recovery with 40 ft (12 m) of interburden and 1,500-2,000 ft (450-600 m) of cover (Kentucky) • Longwall mining directly beneath main entries in overlying seams (West Virginia) • Some of these operations have been highly successful in overcoming the challenges, others less so. The lessons learned from their experience will help ensure that these and similar difficult reserves can be mined safely.

Jan 1, 2006

By Edwin W. Meyer

The augered cast-in-place piling technique was used to install deep foundations 20 feet into weathered sandstone. The project involved the upgrading of the Air Quality Control System (AQCS) for a 560 megawatt coal fired power plant located in Stillwater, Minnesota. The site subsurface consisted of 20 feet of overburden overlying weak sandstone. The overburden consisted of sands and gravels with cobbles and boulders, and variable thicknesses of peat. Ground-water at the site was approximately 8 feet deep. Two foot diameter piers were selected to facilitate installation through the cobbles and boulders in the over-burden and to penetrate the sandstone 22 feet. During installation of the first pier, the weak sandstone broke down to sand-sized material that could not be cleaned from the pier hole without the use of slurry to hold the material in suspension. However, the use of slurry would significantly impact both schedule and cost. Since the sandstone could be easily drilled with the pier equipment, it was believed that 2 foot diameter deep foundations could be installed as designed using augered cast-in-place piling techniques. A brief test drilling pro-gram was conducted to evaluate the viability of 2 foot diameter continuous flight augers penetrating 22 feet into the weak sandstone. The test drilling indicated that augered cast-in-place installation techniques should be successful. Following a short delay to mobilize the additional required equipment, construction commenced. Installation of the 2 foot diameter augered cast-in-place piling to a depth of 22 feet into the weak sandstone was successfully performed.

Jan 1, 2006

By K. Law

"The Hatch Product Transport (HPT) system is a highly flexible and configurable route selection and sequencing system for controlling large bulk material handling facilities. The system has a generic control algorithm that can be configured to suit any material handling facility. It can also be easily reconfigured to cater to plant expansion or modifications without incurring significant disruption to the existing production, costs in testing, and re-commissioning, thus achieving cost savings throughout a facility’s lifecycle.This new material handling control system has been installed at BHP Billiton’s Port Hedland iron ore terminal to facilitate its expansion to beyond 100 Mt output capacity."

Jan 1, 2006

By D P. Murphy, R F. Dewhirst

Traditionally closure has been seen by the Resource sector solely as a green or an environmental issue, focused primarily on the requirement to rehabilitate the site following cessation of production activities. In addition to operational, maintenance and production aspects of processing plant design, future design teams will need to take a more holistic view and consider an increasing number of sustainability issues including safety in design and cleaner production as well as closure itself. Sustainability principles being adopted by industry such as the Minerals Council of AustraliaÆs Enduring Value Framework are now broadening our understanding of closure. While issues around the closure of tailings dams and associated infrastructure have been widely studied, few investigations have looked closely at the implications of closure on the design of minerals processing plants. It is likely that design teams may be able to make a significant contribution to meeting industry objectives by adopting innovative designs which, in addition to meeting production objectives, deliver sustainable and cost effective plant closure outcomes. This presentation explores the opportunity for innovative design of mineral processing plants through the assessment of alternative closure objectives. This assessment specifically looks at current industry standards and statutory requirements, as well as potential risks and opportunities associated with each objective. Alternative design strategies to meet these objectives are discussed.

Jan 1, 2006

By Michael Alber

Resin grouted rock bolts are the major support measure in coal mining. They are rather easy and foolproof to install, take immediately load and are the least time consuming support measure for controlling gateroad deformation. The use of only resin grouted bolts allows fast gateroad development which is essential for economical resource exploitation. The design of reinforcement / support systems for coal mining typically bases on empirical methods, which work fine when encountering known or usual ground conditions. However, coal mining approaches depths where little experience exists and numerical modeling is often the only method to estimate ground behavior. This paper discusses the geotechnical properties relevant to numerical model and focuses particularly on input values for modeling resin grouted rock bolts for safe gate design.

Jan 1, 2006

By M. N. H. Khan

CSIRO has been experimenting with supersonic flows as a method of rapidly quenching metallic vapours. Cooling rates above 106 °C/s have been achieved. The supersonic flow conditions are achieved by adiabatic expansion of the vapour through a Laval nozzle into a vacuum chamber. This paper will describe the basic physics of the process, outlining computer fluid dynamic (CFD) modelling of flow in the nozzle, the effects of different flow conditions on the condensation process and discuss the practical design issues associated with operating supersonic nozzles. Results obtained from a CFD model of the nozzle, which compared two methods of incorporating condensation, showed that inclusion of condensation substantially changes the conditions in the nozzle. Most noticeably, the effect of condensation produces a region in the nozzle where the temperature remains almost constant.

Jan 1, 2006

By S. M. C. Santos

Preliminary bench-scale studies were carried out on the leaching of a zinc sulphide concentrate from Somincor, Portugal, and the purification of the resulting pregnant solution using solvent extraction techniques. The sulphide concentrate contained 36% Zn, 36% S, 2% Fe and 4% Cu. The leaching was carried out with sulphuric acid in the presence of ferric sulphate as the oxidant. Important leaching parameters, such as the effect of reaction time, the solid-liquid ratio, temperature and concentrations of acid and oxidant, were investigated. After leaching, the recovered solution was contacted with an organic phase containing Acorga 5640 to remove the copper. Subsequently, the removal of iron from the leaching solution was achieved with a mixture of Cyanex 272 and TBP. This solvent mixture was relatively selective for iron over zinc. The stripping of the loaded solvent was performed with 200 g/L H2SO4. Six countercurrent extraction stages achieved a separation of about 99% of the iron from the leaching solution. The iron-free leachate can be further treated to recover minor metals by cementation, and finally, zinc by liquid-liquid extraction. The advantages of the suggested process relative to the traditional jarosite process are discussed.

Jan 1, 2006

By John E. Feddock

Retreat mining plays an important role in the coal production within Kentucky and the Appalachian Coal Basin. In Kentucky, the majority of retreat mining is performed in the Eastern coal field. However, since September 2004, Kentucky has suffered four mining fatalities during retreat mining operations, and the coal industry has focused attention on the safety concerns associated with retreat mining practices. The Kentucky Department of Natural Resources (KYDNR) engaged Marshall Miller & Associates, Inc. (MM&A) to conduct a study to ensure that retreat mining is utilizing the best technology currently available and that the current available employee training programs afford maximum safety to miners. MM&A studied 34 coal mines that were conducting active retreat mining operations and represent about one third of all the mines with approved retreat mining plans in Kentucky. This paper summarizes the major research work conducted (Feddock and Ma, 2006) and recommends the practical methods for improving safety during retreat mining operations.

Jan 1, 2006

By Susumu Imashuku

A pseudoternary phase diagram of the BaO?ZrO2?ScO1.5 system is established and the conductivities of the scandium-doped barium zirconate are measured in wet conditions. According to the phase diagram, the molar fraction of scandia in the barium zirconate phase that equilibrates with the cubic zirconia (ZrO2) and scandia (Sc2O3) phase is 0.03. On the composition line, where the molar fraction of barium oxide (BaO) is 0.50, the solubility of scandia into barium zirconate is 0.27 as a molar fraction of scandia. At around 500 °C, the conductivities of scandium-doped barium zirconate are estimated to be almost same as that of yttrium-doped barium zirconateThe activation energies for bulk proton conduction in scandium-doped barium zirconate (0.57 eV for BaZr0.90Sc0.10O3-d) are higher than that of yttrium-doped barium zirconate (0.44 eV for BaZr0.90Y0.10O3-d). In addition, the bulk conductivity of scandium-doped barium zirconate in this study is 10 times higher than the reported conductivities in the temperature range of 75 °C to 300 °C.

Jan 1, 2006

By Thomas M. Barczak

The era of the shield-supported longwall face began in the United States a little over 25 years ago. The most fundamental development of the shield in the past 25 years has been an increase in size and capacity and a progression toward two-legged designs in favor over four-legged shields. Is the ?bigger-the-better? design philosophy justified? The advantage of the two-legged design is largely attributed to its active horizontal force caused by the forward orientation of the leg cylinders. How do we know this? You might be surprised to learn that shield loading data may suggest otherwise. In addition, what about setting pressures? Should they be set as high as possible? Some people have advocated that setting pressures should equal the yield pressure. Does this make any sense? Is yielding a good or bad thing? These are some questions still worthy of investigation that are addressed in this paper. The first major change in gateroad support was the use of cable bolts to replace conventional wood cribbing particularly in Western mines. Standing support changed very little until the mid-1990s, when Strata Products1 introduced the Hercules and Propsetter supports in Eastern mines and Burrell Mining Products introduced the Can support in Western mines. Since then, there has been a dramatic increase in new roof support technologies for longwall gateroad support. Historically, standing support, including shield supports, have been designed based on a simplistic model requiring the support to have sufficient capacity to support the gravity loading of a perceived detached rock mass. This approach ignores the stiffness of the support and the resulting ground deformation that is known to be critical to roof stability. Recently, a new approach based on the ground reaction concept has been promoted by the National Institute for Occupational Safety and Health (NIOSH) to account for the interaction of the support with the rock mass behavior in achieving ground stability. In addition to gateroad support design, this concept has ramifications for shield capacities, setting pressures, and recovery room support design that challenge current practices in these areas. Although longwall mining has matured into the safest and most productive underground mining method used today, traditional concepts of roof support design and practice should still be evaluated and challenged. Ultimately, advancements in the science of ground control are made by recognizing deficiencies in current theories and thinking outside the box.

Jan 1, 2006