Search Documents

By M. Laframboise, M. Buarzaiga

High-pressure acid leaching (HPAL) of nickel laterites has received considerable attention in recent years. High paymetals extraction, good selectivity, and advances in pressure hydrometallurgical technology are some of the reasons for this interest. Falconbridge Limited (Sudbury. Ontario) investigated the HPAL process using both fresh water and seawater for ore processing. The use of seawater resulted in a chloride concentration of 7.8 g/L in the autoclave feed. A test program was developed to study the effect of process water and leach temperature on the leaching behaviour of different ore compositions from the Koniambo deposit in New Caledonia. The work showed that salinity has a major effect on autoclave chemistry. This paper explores the results.

Jan 1, 2004

By M. Suzuki, T. Shiomi, M. Nakada, K. Tsutsumi

Mold powder plays an important role in the continuous casting process for high quality steel production. It is well known that mold powder entrapment causes surface defects in steel sheet and the high viscosity of mold powder prevents the entrapment of mold powder in molten steel in ultra low carbon steel. This paper deals with the entrapment of mold powder caused by suction by Karman?s vortex in a laboratory experiment. At first the effect of the viscosity of oil and interfacial tension between water and oil was investigated in a water model experiment. Then hot model experiments were carried out by mold powder and molten steel. The amount of mold powder entrapment was affected by the viscosity and the interfacial tension between molten steel and mold powder. As a result, the following equation of the mold powder entrapment was obtained. m=1.06*107?-0.255?m-s-2.18 The amount of mold powder entrapment decreased when the viscosity and interfacial tension increased. But the effect of viscosity was larger than that of interfacial tension in the case of the industrial mold powder when the viscosity was under 0.5 Pa.s, interfacial tension was from 1200to 1300 mN/m.

Jan 1, 2004

By Karl Hoover, Cassandra Spence, Brent Bachewich, Jaakko Levanaho

"Since year 2000 the gold recovery into copper concentrate at Hudson Bay Mining and Smelting has reduced considerably during the summer months. This initiated a testwork program in the fall 2003 to find reasons and solutions for such change. During the testwork mineralogical factors, water quality effects and different reagents were evaluated. The reason for the lower recovery appeared to be the sensitivity of some collectors to pulp temperature. As a result of the work different collectors are being used in the mill in the summer than in the winter. A modification to the water system was also made to provide cooler water to the mill in the summer months.INTRODUCTIONHudson Bay Mining and Smelting (HBMS) is located in Northern Manitoba, just on the border of Manitoba and Saskatchewan. The complex consist of four different mines, Callinan, Trout Lake, Konuto Lake and 777 mine including copper smelter and zinc hydrometallurgical plants producing metallic copper and zinc. Gold is a very important byproduct providing about 30% of the mine revenue. In early 1990s when the company was facing declining ore reserves and was starting to gradually close down the operations, the 777’th exploration drill hole discovered a new orebody, which initiated a $0.5 billion expansion program. The main projects were a new 777 hoist with underground development and a new zinc cell house. About $30 million was used to increase the mill throughput to the present 2.27 million tonnes or 2.5 million short tons per year. The expansion programs were finished by the end of the year 2003.Historically the gold recovery at HBMS has varied between 60 and 70%. The recovery has been somewhat lower during the summer months. Gold recovery improvement projects were conducted throughout the 1990s, but were not focused on the seasonal gold recovery variance. However, since 2000, when the water system modifications to meet the increased water demand were completed, the gold recovery during the summer has been much lower than in the past. In August 2003 gold recovery fell below 30%, which initiated a metallurgical research program to discover the reasons behind the low gold recovery in the summer."

Jan 1, 2005

By Jian Deng, Hehua Zhu, Lianyang Zhang

Rockburst is defined as a sudden and violent explosion of rock on the surface of a rock excavation. Rockburst has been regarded as the least understood and most feared hazard problem for underground rock excavations. Traditionally, rockbursts were classified into the strain, pillar, and fault-slip categories. However, rockbursts are also known to occur at stress levels well below the rock yield strength, in mines where the rock is far from brittle, or without the presence of geological discontinuities. A plausible explanation of rockbursts is buckling, which has been identified as one of the main mechanisms for rockbursts. It is observed that rockbursts are often induced by dynamic loadings (pulses) from adjacent blasting. Therefore, the present paper studies the effect of pulse shape and amplitude on pillar rockbursts induced by dynamic loadings from blasting using the method of numerical analysis. The governing equation of a pillar’s motion is set up and the mechanism of pillar rockbursts is investigated through a practical example. The results show that it is not the shape of a pulse but the impact energy to decide the occurrence of pillar rockbursts. If all other parameters remain the same, pillar rockbursts are more likely to occur when the pulse duration is longer. The parametric resonance and the perturbation of dynamic loadings are also found to play an important role in the occurrence of rockbursts. These insights would provide invaluable clues about the mechanism and for better control of pillar rockbursts.

Apr 26, 2022

By R. L. Pozzo

A previous investigation showed that corrosion currents estimated from polarization curves for the pyrrhotite-grinding media system under abrasion correlated well with corrosion currents estimated from marked ball wear test data by applying the Faraday's Law. Freshly abraded metal debris were magnetically attracted to pyrrhotite and lowered the rest potentials of the mineral particles, thereby affecting the corrosive wear. The investigation was extended to explore the interactions between a nonmagnetic sulfide mineral, pyrite, and abraded metal debris and their effects on the corrosive wear mechanism. The electrochemical behavior of a three-electrode system involving pyrrhotite, pyrite and grinding media was also investigated as a first step towards elucidating the nature of interactions that occur in the grinding of complex sulfide ores.

Jan 1, 1987

By J. C. C. C. Menezes, R. A. S. Silva, A. V. Colling, I. A. H. Scheneider

"Coagulants rich in ferric sulfate can be obtained from pyrite-containing coal tailings using a biohydrometallurgical process. The aim of this study is to evaluate the relationship between quantity of pyrite and rate of oxidation, with regard to the consequent production of ferric sulfate for potential use as a coagulant for water and wastewater treatment. Leaching experiments were carried out on the laboratory scale on four coal tailings with different concentrations of pyrite. Characterization of the coal tailings was conducted for the following parameters: total sulfur, pyritic sulfur, sulfate sulfur, organic sulfur, and elemental analysis of CHN (carbon, hydrogen, nitrogen). The samples were also subjected to X-ray diffraction analysis to assess their mineral compositions. The leaching experiments were accomplished using a laboratory column constructed as a packed bed reactor with a sprinkling system in a closed circuit. After four weeks of leaching, the liquor was filtered and evaporated to an iron concentration of about 12 percent w/w, which is typical of the ferric sulfate coagulants commercialized in Brazil. IntroductionCoagulants used for the treatment of water and wastewater are predominantly inorganic salts of ferric iron and aluminum. Aluminum salts, including aluminum sulfate and aluminum chloride, and prehydrolyzed metal-ion reagents, such as polyaluminum sulfate (PAS) and polyaluminum chloride (PAC), are the coagulants most widely used for water treatment (Bratby, 1980; Tchobanoglous et al., 2003; Buzin et al., 2014).However, the presence of residual amounts of aluminum in drinking water has been controversially implicated in neurological diseases (Association of California Water Agencies, 2000; Becaria et al., 2006; Campbell, Hamai and Bondy, 2001; Rondeau et al., 2000; Walton, 2006). A possible alternative is to use iron-based coagulants, such as ferric chloride, ferric sulfate or polyferric sulfate, instead of the aluminum salts (Jiang, Graham and Harward, 1996; Jiang and Graham, 1998). Iron-based coagulants are commonly produced by the acid dissolution of iron scraps or iron ore (Tchobanoglous et al., 2003).Recent studies have shown that it is possible to produce ferric sulfate coagulants from the pyrite present in coal tailings through a biohydrometallurgical process (Colling et al., 2011). The main advantage of this process is that it does not require acid addition, which can be favorable in terms of production costs. Acidophilic bacteria, such as Acidithiobacillus ferrooxidans, can increase the rate of pyrite oxidation and dissolution by several times (Kontopoulos, 1998; Brett and Jillian, 2003; Johnson and Hallberg 2003). They can be highly significant in the bioprocessing of coal tailings for the production of ferric coagulants, as their action favors the acidification of the medium and iron leach (Colling et al., 2011)"

Jan 1, 2016

By Xiaolu Ye

"Comprehensive utilization of Bi and Sn from the tin-associated polymetallic tailings by “gravity separation – flotation combination process” has been studied, which was verified that the novel process is an effective method to deal with the high content pyrrhotite tin-associated polymetallic tailings. In this investigation, ore property analysis and magnetism analysis of pyrrhotite were conducted to research and develop reasonable beneficiation flowsheet. The results of ore property analysis present that pyrrhotite was not closely related to bismuth and tin minerals. Particle size analysis results indicated that pyrrhotite was mainly in the form of fine particles. The magnetic analysis results show that pyrrhotite was distribution in all the three types of pyrrhotite in a single mining area, which indicated that variable magnetism of with different crystal structure pyrrhotite. The process of “low intensity magnetic separation - high intensity magnetic separation” shown an excellent adaption for the high content pyrrhotite tin-associated polymetallic ore compared with the single flotation process based on the magnetism variable of pyrrhotite. The results of whole process test indicated that a bismuth coarse concentrate assaying 5.63% of Bi at 81.77% recovery was obtained, which treat the conditions for the Bi-S separation flotation. In addition, the content of sulfur in the tin concentrate decreased from 2.5% to 1.5%, which provided a new reference for other tin-associated polymetallic tailings. INTRODUCTION Tin has been applied extensively in catalytic chemistry, gas sensors, tin plating, and plumbing. Tin-bearing polymetallic ores have been the important deposit types to recycle tin with the rapid depletion of mineral resources. The comprehensive utilization of the associated elements has been a preoccupation for the mineral processing researchers."

Jan 1, 2018

By H. W. McQuaid

IT IS usually assumed that chemical specifications are sufficient for steel to be used for case carburizing, and if the steel analyzes within the ordinary limits specified for steel for this purpose, no difficulty traceable to the steel used should be encountered in obtaining satisfactory results in the case carburizing and hardening. Much work has been done to determine the effect of various alloying elements on the rate of carbon penetration, etc. but, to our knowledge, little if anything has been published in regard to the effect of the quality of the steel on the final results in the hardening of case-carburized steel parts. The writers believe that the structure of the case both before and after quenching is greatly affected by the actual condition of the steel itself as made, and that for good results in the case-carburizing and hardening departments, the steel should be of the best possible quality as regards non-metallic impurities. It is the purpose of this paper to prove that the presence of excess dissolved oxides in the steel, as made in the melting furnace, affects permanently the results obtained in carburizing and hardening and that it is possible that the presence of dissolved oxide can result in total unfitness of low-carbon steel for, case hardening purposes. When races and rolls for roller bearings are made from a low-carbon steel, case carburized and hardened, it is of primary importance that the results of this treatment be of the highest quality. It is necessary, therefore, that in the case-carburizing work each detail be rigorously checked to avoid any defects which would cause the loss of much time and material. The case carburizing with which this paper deals was done in under-fired oil furnaces. The temperature of each furnace is controlled by means of a platinum platinum-rhodium thermocouple, in connection with a potentiometer indicator and potentiometer recorder. The temperature of each furnace is registered every 15 min. by an operator, who is continually checked by the automatic recorders.

Jan 2, 1922

By J. J. Jonas

The categories of interpass time encountered in hot rolling are characterized. These are shown to fall into three broad categories: short (in rod rolling); intermediate (in strip processing); and long (in plate schedules). The effects of interpass time on recrystallization and carbonitride precipitation are described, and particularly on the interaction between these two mechanisms. The interactions, in turn, determine the final microstructure produced as well as the mechanical properties.

Jan 1, 2005

By Hidenori Hatta, Takero Watanabe, Hideo Yoshida

"The effect of the quenching rate on age hardening in an Al-6.0mass%Zn-0.75mass%Mg alloy sheet was investigated. The quenching rates and aging conditions were as follows: water quenching (WQ) or furnace cooling (FC) followed by pre-aging at 20°C,then artificial aging at 120, 160 or 200°Cwere performed. The peak strength of the FC and the WQ are very similarat120°C aging. It is important high strength was obtained even at the extremely slow quenching rate. On the other hand, the strength of the WQ significantly decreased compared to the FCat200°C aging. GP(I) zones were formed during the pre-aging at 20°C even if the cooling rate was very slow like the FC, and were transformed into the GP(II) ones at 70°C or higher and then into the ?’ phase. However, these zones were dissolved by reversion during heating to 200°C. Thus the strength of the WQ decreased. On the other hand, it is considered that an unknown cluster or GP zone with a thermal stability formed during the FC was not dissolved up to 200°C and was transformed into the ?’ phase. Therefore, a higher strength was obtained in the FC for the200°Caging.INTRODUCTIONAl-Zn-Mg alloys are widely available in commercial production because these alloy have lower quench sensitivity and can be produced by air cooling (AC). Heat treatable aluminum alloys are usually produced by water quenching (WQ) to increase their strength because a high cooling rate inhibits the precipitation of the stable phase during cooling and increases supersaturated solute atoms. However, Baba(1967)reported the strength of an Al-6%Zn-1.8%Mg(mass%) alloy without additional elements quenched by very slow cooling (15°C/min) was 96% of that quenched by WQ. Furthermore,the age hardening at room temperature (RT) occurs after annealing at 410°C followed by furnace cooling (FC, 0.5ºC/min or less)in these alloys. Therefore, the process of annealing at 410 to 430°C for 120 min followed by AC, and reheating at 230°C for 240 min, then cooling is recommended in the specifications (Japan Aluminum Association, 2011). Matsuda and Yoshida(1996)also recommended annealing at 300°C for Al-Zn-Mg alloy extruded products to inhibit age hardening at RT by precipitating the solute atoms and decreasing them in the matrix. It has been considered that the higher the content of excess quenched-in vacancy becomes by WQ, the higher aging rate at RT is obtained. Therefore,it is theoretically and commercially important to clarify the reason why the age hardening occurs relatively quickly in almost no excess quenched-in vacancies such as the FC, and why the same strength as the WQ can be obtained in the FC"

Jan 1, 2018

By K. S. Raja, B. McNall, B. Pesic

"High-level radioactive wastes are stored in large underground storage tanks made of low-carbon steel. The wastes consist of concentrated solutions of sodium nitrate (NaNO3) and sodium hydroxide (NaOH), and the radionuclides 137Cs, 99Tc, and 90Sr. The corroding steel microenvironment may produce localized reducing or oxidizing conditions that affect the solubilities of the species such as Tc(VII) and Tc(IV), which in turn modifies the kinetics of corrosion of the storage tank. To understand the influence of technetate ions on the corrosion of steel, electrochemical polarization studies of A 537 steel samples were carried out in 1 M NaNO3 + 0 .05 M S r(NO3)2 + 0.1 M NaOH with and without addition of HReO4 at different temperatures (24 – 85 °C). The concentration of HReO4 was varied from 0.014 – 0.04 M.INTRODUCTIONAqueous processing of spent nuclear materials generates a large amount of high-level radioactive wastes. The wastes are primarily salt solutions of sodium hydroxide and sodium nitrate which also contain fission products such as 137Cs, 99Tc, and 90Sr. Among the high level radioactive fission products, Tc-99 is of great importance because of its high concentration, long half-life (2.1 x 105 years), high solubility in geologic waters as technetate, and rapid diffusivity through the geologic systems. The solubility of technetate ions varies depending on the oxidizing conditions prevailing in the storage containers. High level radioactive wastes are stored in single shell or double shell tanks made of low carbon steels such as ASTM type A15, A516-70 and A537. Most of the available literature on corrosion of steel in simulated radio active waste environments pertains to nitrate induced stress corrosion cracking (Subramanian & Mickalonis, 2005). The corroding steel microenvironment may produce localized reducing or oxidizing conditions that affect the solubilities of the species such as Tc(VII) and Tc(IV). Corrosion of steel and formation of Fe(II) and Fe(III) will affect adsorption and reduction of Tc species. The radioactive species can irreversibly be sorbed on the steel surface by oxidation of Fe(II) to more stable Fe(III) and fixed as less soluble Tc(IV)/Fe(III). The solubility of Tc species is also affected by other factors such as dissolved oxygen, local pH, temperature etc. How the corrosion behavior of steel will be affected in the presence of Tc species is not clearly understood.Cartledge (Cartledge, 1960) demonstrated that passivation of iron can be achieved in the presence of oxygen along with suitable inhibitor ions/molecules of the general formula XO4 n-, such as pertechnetate (TcO4 -). The pertechnetate ion is univalent. Since it is derived from a strong acid, no buffering action can be expected from this ion. The redox potential of the reaction (1) is 0.738 VSHE (Pourbaix, 1974)."

Jan 1, 2012

By S. Khoshkhooei

In this research, the effects of rare earth elements addition on thermal fatigue behaviors of AZ91 alloy were studied. Repeated heating and cooling cycles were applied on the samples at 170°C and 210 °C to develop thermal fatigue cracks, Crack growth mechanisms and microstructural influences were investigated by optical and scanning electron microscopy (SEM) as well as energy dispersive X-ray spectroscopy (EDS), Thermal fatigue behaviors were improved successively by addition of up to 2-wt% RE, This improvement is attributed to consummation of the aluminum of the melt by precipitation of the needle shape Al 11 RE3 phases, This process reduces the volume of Mg17Al12 phases and consequently decreases the brittle Mg/Mg17Al12 interfaces which are the main reason of weak thermal properties of the alloy at rather high temperatures, Further additions of RE, however, reduced the thermal shock resistance of samples by increasing in the mean length of the brittle needle shape phases.

Jan 1, 2005

By Richard L. Stowe, Donnie L. Ainsworth

The static, rapid, and shock-loading response of rock is of interest to many in the field of rock mechanics. For example, the effects of loading rates on strength and stress-strain characteristics of rock are quite important in defining input loading for use in the design of underground protective installations. Response data on rock subjected to shock loading over a wide range of pressures are also vital in the field of underground nuclear testing. In addition, material response is needed in design of shock-absorbing liners. A number of investigators have reported that ultimate compressive strength of rock increases with increased rates of loading.1-6 Wuerker3 stated that modulus of elasticity, obtained from sonic determinations, increased in some rocks by a factor as high as 4.5. It appears that only a limited amount of work has been done on comparing static modulus and modulus obtained from impact testing.6 Phillips4 showed that with increased rates of loading the deformation decreased. More recent work by Atchley and Furr5 showed that when moderate-strength concrete is stressed with increased loading rates, the axial strain at failure increased. One would expect this to occur if we think in terms of purely elastic materials. For example, if E is constant and maximum strength [amax], increases, the axial strain would also increase. However, in rock testing thus far we have worked almost exclusively with nonhomogeneous and inelastic rocks. From this fact alone the increase in axial strain with increased load application is noteworthy.

Jan 1, 1972

By Jue Kou, Hongda Xu, Tichang Sun, Shichao Wu, Wenli Han

To investigate the effect of simultaneous change in particle size of raw materials (including ore, reductant, and dephosphorization agent) on the direct reduction process of high-phosphorus oolitic hematite, the experimental research of method with direct reduction and magnetic separation was conducted to investigate the effect of simultaneous change in particle size of raw materials on the final reduction products in the form of mineral composition, reduction speed, metallic iron particle morphology, phosphorus distribution, and powdery reduction iron. The results revealed that under the same conditions of reduction temperature, the raw material particle size affects the mineral composition of the final reduction product, the coarser the raw material particle size, the slower the reduction speed, the lower the metallization rate, and the larger the final metallic iron particle size formed. Under the same conditions of raw material particle size, the reduction temperature affects the mineral composition of the final reduction product, the higher the reduction temperature, the faster the reduction speed, the higher the metallization rate, and the larger the size of metallic iron particles within a certain reduction time. Neither the raw material particle size nor reduction temperature affects the form of phosphorus present in the reduction product. Both the raw material particle size and reduction temperature affect the grade of powdery reduction iron to a less extent, but affect the recovery rate and phosphorus content significantly. At the same reduction temperature, the recovery of powdery reduction iron and phosphorus content gradually decreases with the increase in raw material particle size. For the same raw material particle size, the recovery of powdery reduction iron gradually increases, and the phosphorus content gradually decreases with the increase in the reduction temperature. The results identified the effect of simultaneous changes in particle size of raw materials on the direct reduction process of high-phosphorus oolitic hematite and provide a basis for the selection of raw material particle size for the industrial application.

Dec 20, 2022

By D. Malhotra

The effect of some of the reagents, namely hydrocarbon oil, Syntex (sulfated coconut oil surfactant), pine oil, sodium silicate, and lime, used at the Climax mill on the recovery and grade of molybdenite and gangue minerals has been investigated experimentally using factorially designed test approach in the laboratory. The results of the investigation are presented in two dimensional plots. The lower additions of lime (equivalent to a pH of 8 to 8.5) were desirable for maximizing recovery subject to constraints on grade. Higher additions of pine oil improved recovery, but only at the expense of grade. A mathematical model of the objectives of an operating plant was formulated and optimum reagent conditions obtained.

Jan 1, 1977

By E. Matinde, S. L. Msibi

"The robust nature of alumina refractory materials presents opportunities for their in-process reclaiming and re-use in non-critical applications. Virgin refractories can be substituted with different quantities of reclaimed materials without compromising the quality of the refractory products. In this study, the effect of reclaimed bauxite on andalusite-containing refractory castables for tundish applications was investigated. The recycled bauxite was formulated in different proportions to replace virgin andalusite in the castables. Standard tests were conducted to evaluate the physical, physicochemical, and thermochemical properties of the formulated products. Static corrosion tests were conducted using tundish slag in order to simulate the actual operating conditions. The results show that the standard flow behaviour, open porosity, and bulk density of samples containing up to 22 mass% reclaimed bauxite were comparable to those of the reference castable. However, high-temperature properties such as static corrosion at 1400°C and hot modulus of rupture at 1500°C indicated that there is an upper constraint to the amount of substitution. The study demonstrated direct potential savings of up to 10% when the reclaimed alumina replacement ratio was increased to 22 mass%. IntroductionAlumina-based refractories can be classified into low-alumina, containing less than 50% Al2O3, and high-alumina or bauxite, containing between 50 and 90% Al2O3. High-alumina refractories have widespread applications in high-temperature metal extraction processes due to their outstanding thermochemical and thermomechanical properties and stability (Rebouillat and Rigaud, 2002; Frulli, 2016). The typical chemical composition of refractory-grade bauxite consists of 85–90 wt.% Al2O3, 5–10 wt.% SiO2, 1–2wt.% Fe2O3, 3–4 wt.% TiO2, 0.4–0.8 wt.% CaO + MgO, and 0.20–0.8 wt.% K2O + Na2O (Nyoka et al., 2013). The thermochemical and thermomechanical properties of bauxite-based refractories rely principally on the conversion of the contained silica and alumina to the highly stable corundum (?-Al2O3) and mullite (3Al2O3· 2SiO2) phases (Rebouillat and Rigaud, 2002; Hill and Sehnke, 2006; Garbers-Craig, 2008; Frulli, 2016)."

Jun 1, 2019

By S. Castro, L. Gutiérrez, L. Uribe

"Use of lime in seawater as a pyrite depressant decreases Mo recovery in flotation of Cu- Mo sulfide ores. When technology that uses sodium metabisulfite (MBS) to depress pyrite is applied, the process is carried out at pH 6.5–7.5, the range where Mo recovery is higher than the usual pH 11.0–12.0 when lime is applied. Redox conditions and chemical reactions involved in depression mechanisms of pyrite by MBS, or sodium sulfite, in seawater are investigated and discussed based on the acidifying effect of MBS, oxidation of sulfite ions by dissolved oxygen, and the role of catalyst of some metal cations (e.g., copper ions) adsorbed on pyrite’s surface.RÉSUMÉ L’utilisation de chaux dans de l’eau de mer comme agent déprimant de la pyrite réduit la récupération de molybdène (Mo) dans la flottation de minerais sulfurés de Cu-Mo. Lorsque l’on applique la technologie utilisant du métabisulfite (MBS) de sodium comme agent déprimant de la pyrite, le procédé se fait à un pH de 6,5 à 7,5, gamme dans laquelle la récupération de Mo est supérieure au procédé habituel utilisant un pH de 11,0 à 12,0 lorsque l’on applique de la chaux. Les conditions de réduction-oxydation (redox) et les réactions chimiques impliquées dans les mécanismes de dépression de la pyrite par le MBS (ou sulfite de sodium) dans de l’eau de mer sont étudiées et débattues sur la base de l’effet acidifiant du MBS, de l’oxydation des ions sulfites par de l’oxygène dissous et du rôle de catalyseur de certains cations métalliques (par exemple les ions de cuivre) adsorbés à la surface de la pyrite. INTRODUCTIONThe copper industry is aware of the difficulties of floating Cu-Mo sulfide ores in seawater. Molybdenum recovery is partially depressed when lime is used to reject pyrite. In plant practice, sodium metabisulfite (MBS) has been demonstrated to be the most promising option for replacing lime in seawater."

Jan 1, 2017

By De-qing Zhu, Zi-fu Gao, Jian Pan

"In order to produce high quality metalized products and prevent from burden cohesion during pre-reduction, self-fluxed pellets were made for COREX process in the paper. The effects of reduction temperature and reducing gas composition on pre-reduction behaviors of self-fluxed pellets are studied. The results show that the prereduced pellets have poor quality and deposited carbon appears when the reduction temperature is between 600°C and 700°C. The metallization rate, reduction degree and compressive strength of prereduced pellets are promoted by the elevating reduction temperature and mole fraction of H2. Pellets reduced by pure H2 at 800°C have high metallization rate (96.2%), reduction degree (99.4%) and compressive strength (960N/pellet). In all tests, self-fluxed pellets display normal swelling (RSI<l5%) behavior which reveals that self-fluxed pellets are suitable for COREX process. Increasing reduction temperature and mole fraction ofH2 in reducing gas is benefit for pre-reduction of pellets.IntroductionCompared with Blast Furnace, the COREX process has advantages of short flow sheet, using non-coke coal and high-energy utilization. Acidic pellets and lump ores are the chief iron- bearing burden for COREX process which could lead to low melting point substance appearing in per-reduction process. In addition, the acidic hematite pellets tend to swell during the reduction [1-3]. This will result in decreasing compressive strength of pellets, burden cohesion, bad air permeability and poor work status in shaft furnace. Adding carbonate flux could restrain burden bonding to some extent in actual production, but decomposition of carbonate flux increases energy consumption. Worse still, weak reduction potential is unfavorable to iron material reduction [ 4, 5]."

Jan 1, 2013

By Zhiyun Li

Room temperature infrared reflection spectra of 2 n-type homo-epitaxial epifilms have been measured in the work. The effect of the refractive index on the determination of layer thickness using traditional calculation measurement is studied and some improvements have been added to the measurement to improve the accuracy and stability of the measured results. Results of the improved method have great agreement with the results from SEM and both variance and mean relative error decrease an order of magnitude.

Jan 1, 2010

By M. A. Berdine, C. N. Thompson, D. Brock

The raise bore method of shaft construction has been success-fully used in the mining and construction industries for over thirty years. In the mid 1990’s, Twentymile Coal Company (“TCC”), now affiliated with RAG American Coal Company, used this method for a moderately deep small diameter shaft and the raise bore and slash method for a shallow larger diameter shaft. In late 2001, TCC contracted to raise bore a 431-meter deep, 6.2-meter diameter shaft. During the raise bore and shaft lining processes, regional horizontal stress fields resulted in extensive elliptical caving beyond the original design diameter. This paper discusses the engineering approaches and procedures used to safely complete construction of the raise bore shaft.

Jan 1, 2004