Search Documents

By P. Harris, D Bradshaw

"Comparison of the two most commonly used classes of depressant in the South African platinum industry is complicated by the fact that these polymers induce different effects on the surfaces onto which they adsorb. The use of carboxymethyl cellulose (CMC), which is ionically charged in solution, can lead to increased particle dispersion in addition to the effect of reduced surface hydrophobicity (depression). Guar is typically only slightly charged in solution. Comparison of these two depressants is complicated since it is uncertain whether differences in their action is a result of either depression of dispersion effects.This work investigates the role of dispersion independently to that of depression in the batch flotation of a platinum bearing ore. An inorganic dispersant, sodium hexametaphosphate (NaHMP) was added in parallel to the uncharged guar depressant to simulate the action of depressants with varying degrees of dispersion. By distinguishing between the material recovered by entrainment and the floatable gangue and by including the effects of froth stability it was possible to decouple the effects of dispersion and depression.The results show that both dispersion and depression led to increased grade of the sulphide minerals. Depression leads to a decreased recovery of floatable gangue minerals. Dispersion leads to an increased recovery rate of these minerals and an accompanying decrease in froth stability."

Jan 1, 2003

By B McFadzean, N P. Lima, D A. Deglon

The reverse flotation of Itabirite iron ore is typically performed after a desliming step in which most of the sub-10 µm particles are removed. This is done to limit processing problems such as poor flotation recovery of SiO2 due to slime coatings and increased slurry viscosities, unmanageable froths and increased losses of hematite particles due to entrainment. However, the rejection of ultrafine particles contributes to large losses in iron recovery and may contribute to the instability of tailings dams. The aim of this study is to decouple the effects of ultrafine particles in the pulp and froth phases to better understand the processing capabilities of the fines fraction. The flotation test work was performed in a special-purpose continuously operated laboratory flotation cell that has a deep froth section to simulate plant-scale froth conditions. Five conditions of fines addition were investigated at three different froth heights and a solids concentration of 50 per cent. The behaviour of the pulp and the froth were decoupled using froth stability and froth recovery tests. This showed that, even though there is an exponential increase in froth stability at increasing fines quantities, the performance of the pulp has the overriding effect on the overall SiO2 recovery. Pulp zone, froth zone and overall SiO2 recoveries showed that overall recoveries increased by about 3.6 per cent for every 1 per cent decrease in fines content. This meant a large increase of 20 per cent in SiO2 recovery when going from undeslimed to deslimed feed. This was driven largely by increases in the pulp zone recoveries, which were about 4 per cent for every 1 per cent decrease in fines content. The froth recoveries, on the other hand, decreased by between 0.75 per cent and 2.5 per cent for every 1 per cent decrease in fines content, depending on froth height. This paper explores further insights into iron ore flotation processing at different slimes concentrations.

Aug 24, 2022

By S Hapugoda, M Kilburn, M Adam, L Lu

Lump ore is one of the key ferrous materials used in the blast furnace ironmaking process, typically accounting for 5–25 per cent of the blast furnace ferrous burden. Like other ferrous materials, the characteristics of lump ore have an important impact on stable operation and productivity of a blast furnace. As the cold burden lands on the top of the hot burden in the furnace and descends, it is inevitably subjected to thermal shock, which will likely lead to breakdown of the lump particles, or decrepitation and affect the gas permeability inside the blast furnace adversely. An ISO decrepitation test has therefore been developed to assess this behaviour of lump ore. However, the results obtained according to the existing standard decrepitation test method vary considerably between laboratories even for the same lump ore. To improve the test procedure of the existing decrepitation test, this paper first discusses the mechanisms leading to decrepitation and then studies the factors affecting lump ore decrepitation. Understanding the key factors affecting lump ore decrepitation is particularly important to improve the existing test procedure that enables researchers to achieve a higher degree of precision when conducting the decrepitation test.CITATION:Lu, L, Adam, M, Hapugoda, S and Kilburn. M, 2017. Decrepitation of lump iron ores, in Proceedings Iron Ore 2017, pp 91–96 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

The new Ceramic Engineering Building of the University of Illinois is to be formally dedicated on Nov. 20 and 21. The occasion will be made one of great interest to the clay-workers of the country. It is expected that the exercises will be attended by many representatives of the architectural, structural, mining, geological, chemical, and manufacturing interests. In connection with the dedication exercises, an industrial conference will be -held, in which a number of topics of current interest to the ceramic engineer, the clay-worker and the manufacturer will be discussed by well-known experts. : The number of students registered in the College of Engineering of the University of Illinois eleven days after the beginning of registration - for the new year, is as follows: Architecture, 116; Architectural Engineering, 167; Ceramic Engineering, 46; Civil Engineering, 190; Electrical Engineering, 266; Mechanical Engineering, 273; Mining Engineering, 25; Municipal and Sanitary Engineering, 26; Railway Engineering, 34; total, 1,143. The enrollment of students in the whole University, not including the College of Medicine, the College of Dentistry and the School of Pharmacy, which are located in Chicago, is 5,21.4.

Jan 10, 1916

Jan 1, 1892

By Norman A. M Macleod

FOR the past seven years, all flotation at the Britannia mill has been done in Forrester Air-Lift cells. Prior to 1931, the roughing and part of the cleaning operation had been performed in four 21-cell and two 14-cell M.S. machines. The resulting economies in reagent, power, maintenance, and general operating costs, and the increased recovery, more than justified the exclusive use of the Forrester machine. About three years ago, the possibility of still further improving the efficiency of the flotation section was the subject of considerable discussion and experiment. Arising from these experiments, tests were made of the practicability of using a cell of greater depth than that of any pneumatic or mechanically-agitated machine in common use. Cells were constructed with depths of 7 .5 feet, 10 feet, and 15 feet, and, in all cases, a very definite improvement in operation was indicated. The cell now being used in the mill treats from 5,500 to 6,200 tons of dry feed per day. It is 100 ft. long by 5 ft. wide by 8 ft. deep, and has replaced a total length of over 500 feet of standard Forrester machine. The choice of a depth of 8 feet was governed by the type of blower which was available-in this case, a Roots-Connersville blower, driven by a synchronous motor and delivering 6,000 c.f.m. of free air at 4.0 pounds per square inch. At the Chelan Division of the Howe Sound Company, where a new mill was recently built, all flotation is carried on in cells 10 feet deep, with good results.

Jan 1, 1938

By Wu Jie Mei, Li Yao Liang, Franz-Werner Gerressen, Arthur Bi

Diaphragm walls (D-walls) are known as underground structural elements commonly used for retention systems and permanent foundation elements. In addition, they are also quite often used as deep groundwater barriers, called Cut-Off-Walls (COW). Shanghai ranks third among the most densely populated metropolises in the world. In 1990, only eight million people lived there. Today, Shanghai has about25 million inhabitants. The increasing demand to accommodate the infrastructure of growing megacities like Shanghai pushes the required depth for subway, sewage and foundation projects to the limit. Future projects will demand excavation depths of more than 100 m (328 ft) on a regular basis. Already carried out reference projects will be described and a general outlook for upcoming projects will be given. The paper also explains the installation process in general focusing on the use of trench cutter technology. INTRODUCTION D- walls are known as underground structural elements, commonly used as retention systems for excavation pits and shafts as well as permanent foundation walls or elements. It is anticipated that, with the increasing trend of utilizing more and more underground space to accommodate environmental considerations and urban/suburban development, there will be an increasing requirement for diaphragm wall usage in even more difficult conditions and with increasing depth. The trench cutter is the most important tool for performing this work. The hydraulic grab, a well-known and valuable excavation tool for d-walls reaches its limits in terms of depth and when cutting rock. Therefore the trench cutter technology will be in the focus of this paper. The trench cutter itself is a reverse circulation excavation tool. It consists of a heavy steel frame with two drive gears attached to its bottom end, which rotates in opposite direction around the horizontal axis. Cutter wheels are mounted onto the drive gears. As they rotate, the soil beneath the cutter wheels is continuously broken up, removed, mixed with the bentonite slurry in the trench and moved towards the opening of the suction box of the pump? A centrifugal pump located right above the cutter wheels conveys the slurry via a hose system up to a desanding plant. There the slurry loaded with soil and rock particles is cleaned and returned into the trench.

Jan 1, 2018

By Alessandro Bertero, Dylan Pearson, Wesley Schmutzler, Matteo Bertoni

"The SR 83/US 331 highway is located in the Florida panhandle, where it connects the Walton County beaches to the I-10 corridor. The roadway is of vital importance to the economy of the area as well as its safety since it represents the primary hurricane evacuation route from southern Walton County. The Florida Department of Transportation (FDOT) decided to increase the number of traffic lanes from two to four and improve the geotechnical properties of the moderately deep, very loose foundation soils, that had affected the highway rideability for years. The soil mixing was selected as the method to meet the unique deep ground improvement challenges of the project. The design required that Shallow Mixing Method (SMM) be used to build a 10-foot thick platform that transferred axial load to the bottom soil layers through a series of Deep Mixing Method (DMM) columns. Upon completion over 8,300 SMM columns and 1,500 DMM columns had been installed, with no remedial work required. Also, only 1% of the almost 1,500 specimens tested did not meet the specification requirements. This paper will describe the challenges encountered and provide valuable information that may be useful for other future projects, including details not previously published.INTRODUCTIONThe counties of Walton and Okaloosa have been a very popular vacation destination for many ears. The 50-mile long coastline boasts beautiful, sugar-white beaches and waters the color of emeralds. The popularity of the area has been growing even further, over the last few years. A consequence of this phenomenon is a fast-paced increase of the traffic flow on the SR83/US331 highway, especially at the bridge that connects the Walton County beaches across Choctawhatchee Bay (Fig. 1) to the heavily traveled I-10 corridor. The highway plays a very important role for the area also as a commercial link and as the primary hurricane evacuation route from southern Walton County. The increase in traffic has produced higher travel time, when not a complete traffic paralysis, and exacerbated the issue of ground settlement where accelerated wearing of road foundation occurred due to the presence of very loose, moderately deep, soils, that had afflicted the highway for several years. The Florida Department of Transportation (FDOT) decided to put an end to these issues by increasing the number of traffic lanes from two to four and improving the geotechnical properties of the foundation soils. The Design-Build Maximum Price Request for Proposal (RFP) issued for the expansion of the Choctawhatchee Bay Bridge saw the participation of numerous D/B teams which produced various technical solutions. Among them, the FDOT selected the Skanska/Parsons Brinckerhoff (General Contractor) proposal which provided for the use of soil mixing as the ground improvement technology. The design/build team assigned Foundation & Geotechnical Engineering (Designer of Record) the ground improvement design which Treviicos South (Specialty Contractor) would execute."

Jan 1, 2017

By T. G. Paradis, C. A. Mohns

"This paper summarizes the Wren CAT (Clarifier and Accelerated Thickener) deep bed thickener operation at the EKATITM Diamond Mine in Canada’s Northwest Territories. EKATITMs’ thickener project is presented in terms of initial design considerations and present day operating practices. A circuit description summarizes process equipment, reagent systems, and typical process conditions, and details of Wren CAT operating principles are provided. Operating strategies are discussed, with emphasis on process instrumentation and control and operating challenges.INTRODUCTIONThe EKATITM diamond mine, operated by BHP Diamonds, Inc., is located in the Northwest Territories near Lac De Gras, approximately 300 km NNE of Yellowknife, NT. 9000 dry metric tonnes of diamond-bearing kimberlite ore are processed daily. Processing operations commenced in October, 1998.The EKATITM process plant flowsheet features typical steps in diamond recovery plant design. Figure 1 shows the general plant flowsheet. Size reduction and feed preparation are accomplished by crushing, scrubbing, and high pressure grinding rolls (HPGR) through closed-circuit classification with vibratory screens. Heavy medium separation (HMS) is used as the initial stage of heavy mineral concentration. Secondary concentration is accomplished in the recovery plant by attrition milling; wet, high-intensity magnetic separation (both wet and dry); and X-ray sorting.The present budget throughput rate is 9000 dry tonnes per day. This will be increased to 18,000 tonnes during the first ten years of operation. Unlike most kimberlite treatment facilities, which process material from a single ore body, EKATITM’s process plant was designed to accommodate ore from five different kimberlite pipes, each with its own treatment characteristics.All processing, except for primary crushing, is carried out in a temperature-controlled environment in the main process plant building."

Jan 1, 2000

By W. Sondermann

"AbstractThe construction of a distribution centre of minerals for a global mining and resources cooperation demanded the control of deformations and displacement of the stack reclaimer facilities on very inhomogeneous subsoil conditions. The variation of quality from soft clay with CPT values below 1 MPa up to rock formations were the challenge in design and execution of all the foundation works.The advanced design considerations were resulting in a barrier wall system to limit the deformations of the up to 40 m deep bored pile of the stacker-reclaimers, whereas the layout of the barrier wall and the stiffness of the elements had a major impact on the residual lateral forces to be absorbed by the bearing structure.IntroductionA large international raw material distribution organisation is currently building an iron ore and pellet distribution centre on the north-western coast of Malaysia. The distribution centre will handle around 90 MTPA (million tons per annum) of iron ore and includes accompanying plants for loading and unloading iron ore and pellets, pelletizing plants as well as corresponding storage space for these raw materials. The total storage space extends about 800m north to south respectively 1400m east to west and is about 200m from the coastline. The project area is located in a wide valley basin, bounded by a range of hills to the north. The existence of soil with low bearing capability in the area designated for the plant meant that measurements for ground improvement were required in the storage areas, in order to combine the needs of iron ore and pellet storage areas with requirements of the loading facilities as the overall project demand.Project LayoutThe iron ore distribution centre and the pelletizing facility both consist of an import/export jetty, material handling facilities, pellet plant and the associated infrastructure. This publication describes the execution of ground improvement and foundation works for the loading and storage system, which consists of five rows of stockpiles and four intermediate rows of stacker-reclaimers. The total area of these systems comprises 278,881 m2 (Fig. 1)."

Jan 1, 2014

By Judith S. Chan

With the increasing awareness of the need for the reduction of carbon emissions globally, geothermal energy, which offers a potential for cleaner energy generation, is one potential new source. In Alberta, these geothermal resources are likely to be found in the sedimentary basin, or in the deeper crystalline basement rocks. Alberta exhibits a very low geothermal gradient compared to other existing geothermal fields located in areas of volcanic and tectonic activity. To mitigate this effect, the focus in Alberta will involve the development of engineered geothermal systems (EGS) in the target resource. The first goal for EGS research and development is to develop a detailed geological-geophysical characterization of selected sites to delineate potential geothermal reservoirs in Northern Alberta. One of the selected sites is in the Fort McMurray area. The deepest well drilled in the oilsands areas of Northern Alberta is located just west of Fort McMurray. It has a depth of 2363 m and as such can provide details on the physical properties of the rocks, the state of stress, and the existence of fracture porosity toward geothermal investigations. To date, we have acquired temperature logs to study the change in geothermal gradient with depth, and a series of petrophysical logs to study the finer scale structure of the rock formations with vertical resolutions in the range of 0.05 cm to 80 cm. Our aim is to identify geological features such as zones of fractures in the basin and/or basement that could provide an indication of enhanced fluid flow potential ? a necessary component for any geothermal systems to be viable. Zero offset and walkaway vertical seismic profiles (VSP) were also conducted to measure the seismic responses at the borehole. VSP data can be used to delineate the structural and stratigraphic features surrounding the borehole that could not be resolved from surface seismic reflection data that are also available near the borehole. The full integration of well logs, VSP data and surface seismic reflection data are expected to provide a detailed characterization of the sedimentary basin and crystalline basement rocks of the Canadian Shield in Northeastern Alberta and will assist in future planning for drilling.

Jun 1, 2012

By C. Y. Liu

This paper principally deals with the application of caisson foundation in the Chinese bridge building industry, the different types of caisson foundation adopted, and their spheres of application. Caisson foundation has been used and speedily developed for bridge works in New China, and a number of new innovations have been made in its design. Especially in deep water foundation, the Nanjing Bridge over Changjiang has attained one of the deepest bridge foundations in the world. There are six types of deep caisson foundation being now in use in China, namely:

Jan 1, 2010

By Sameh M. Khella

This paper discusses the application of deep CFA piles for the foundation of structures in different ground stratifications with a focus on the application in Queensland region. Design, construction techniques and quality measures implemented during these procedures are described. Testing methods and verification of capacity, integrity and performance of these piles are also demonstrated. Case studies for this application are presented with an appreciation of this solution within the provided project conditions of each case. Examples of successes and challenges encountered over the course of application of deep CFA in Queensland are mentioned. Limitations of the technique and less favourable situations for its implementation are also highlighted.

Nov 1, 2022

By Z. G. Lin

In Xian, China, compaction by means of soil (or lime-soil) piles is one of the effective methods widely used for densifying loess and eliminating its collapsibility. However, as a result of groundwater table rising, it is no longer applicable in many areas. This paper is the summary of the first-time use in Xian of sand-gravel compaction piles aimed at densifying the miscellaneous fill (already partially under water) and saturated loess at a certain project site. In-situ tests, conducted before and after the treatment and including several kinds of penetration tests backed up and confirmed by a set of plate loading tests, yielded very satisfactory results, strongly testifying to the viability of the method.

Jan 1, 2010

By Tulu B. Ihsan, Mark A. Van Dyke, Ted M. Klemetti

"How well do current modeling procedures calculate the rear abutment extent and loading? Does an improved understanding of the rear abutment extent warrant a change in standing support in bleeder entries? What is the optimal standing support for bleeder entries separated from the longwall startup room by a barrier pillar? To help answer these questions and to determine the current utilization of standing support in bleeder entries, four bleeder entries at varying distances from the startup room were instrumented, observed, and numerically modeled. This evaluation was intended to determine the rear abutment extent and magnitude at various locations to optimize standing support in these entries and those under similar conditions. This paper details observations made by NIOSH researchers in the bleeder entries of a deep cover longwall panel; specifically data collected from instrumented pumpable cribs, observations of the conditions of the entries, and numerical modeling of the bleeder entries during longwall extraction. The primary focus was on the extent and magnitude of the abutment loading experienced by the standing support. As expected, the instrumentation of the standing supports showed very little loading relative to the capacity of the standing supports—less than 25 tons load and 1 inch convergence. The observations of the conditions showed little to no change from before the longwall panel extraction began to when the panel was more than 50% extracted. In addition to the observation and instrumentation, numerical modeling was performed to evaluate the bleeder design. The Flac3D program was used to evaluate these four bleeder entries using previously defined modeling and input parameter estimation procedures. The results indicated only a minor increase in load during the extraction of the longwall panel. The model showed a much greater increase in stress due to the development of the gateroad and bleeder entries, with about 80% of the increase associated with development and 20% with longwall extraction. The Flac3D model showed very good correlation between expected gateroad loading during panel extraction and those expected based on previous studies. The front and side abutment extent modeled was very similar to observations from this and previous panels with similar conditions. The results of this study showed that the rear abutment stress experienced by this bleeder entry design was minimal. The convergence measured in these bleeder entries was small enough not to mandate any additional support beyond development even by U.S. or Australian standards. The pumpable crib load and convergence experienced depends on the geological setting, mining geometries, and timing. The farther away from the startup room, the lower the applied load and smaller the convergence in the entry if all else is held constant. Finally, the numerical modeling method used in this study was capable of replicating the expected and measured results near seam."

Jan 1, 2017

By Keith A. Heasley, Frank E. Chase, Christopher Mark

Deep cover retreat mining (overburden in excess of 750 ft) is an important emerging issue which will intensify in the future as the more easily mined shallow seam reserves are depleted. Analysis of Mine Safety and Health Administration (MSHA) statistics indicates that deep cover pillar recovery accounts for a disproportionate share of the underground coal mine roof/rib fall fatalities and injuries. Past research has shown that previously recommended Analysis of Retreat Mining Pillar Stability (ARMPS) stability factors (SF’s) may be excessive for deep cover pillar design. The objectives of this study were to evaluate the various methods and strategies by which panels, production pillars and barrier pillars are developed and extracted under deep cover, and to develop appropriate design guidelines. In the course of the research, 29 mines in 7 states were investigated to collect panel design case histories. At each mine site, underground geotechnical data were collected on the pillar line in order to document roof rock, coalbed and floor conditions. The analyses indicated that squeezes were the most likely failure mode where the depth was less than 1,250 ft, but bumps predominated in the deeper cover cases. Immediate roof rock quality, the ARMPS SF’s, and barrier pillar stability factors were all found to be important parameters in determining the outcomes of the case histories. Design guidelines, including suggestions for barrier pillars to isolate active panels from nearby gobs in bump prone ground, are also proposed.

By E. R. Bauer

The trend in underground room-and-pillar coal mining is to employ remote-control continuous mining machines and extended cuts, 12 m (40 ft) deep or more. This system of coal extraction, adopted by over 435 mines, can create additional worker-safety hazards. To address the ground control and worker-positioning hazards, a combination of statistical analyses and numerical modeling was conducted. Initially, the reported roof-fall incidents and fatalities were reviewed to delineate the ground-control hazards. Then, the application of the Coal Mine Roof Rating (CMRR) for estimating safe extended-cut depths was evaluated. Finally, computer modeling to predict roof displacements during extended-cut mining was completed. The paper describes the results of these studies and their impact on the safety of extended-cut mining.

Jan 1, 1999

By Klaus Pöllath

The Netherlands RandstadRail project makes use of a large range of sophisticated geotechnical techniques to allow a shield driven tunnel to approach the central station of Rotterdam. This paper describes the construction of three deep excavation pits constructed with 1.2 m and 1.5 m thick diaphragm walls. Besides the presentation of the actual diaphragm wall activities special consideration is given to the break-in and break-out situations of the TBM into the deep excavations pits using sealing blocks and partly glass fibre reinforcement in the diaphragm walls.

Jan 1, 2006

By Wolf-R. Under

For improvement of urban traffic infrastructure, the City of Amsterdam is cur­rently constructing the 9.5 km long North-South Metro line passing through the central districts of Amsterdam. Focal section of the project is the Central Station linking the NS Line with the Central Railway Station, the East Metro line, new bus and tramway terminals, ferries and individual traffic. Construction works required for the project are of high complexity and technical standards. They are executed under severe restrictions concerning programming, space, logistics, and impact on the integrity of existing buildings and structures as all existing installations and facilities have to maintain fully operational during the construction period. The paper deals with the main geotechnical features of the project and in particular with the diaphragm wall and bored pile construction at the Voor-plein and the De Ruijterkade sections of the Central Station.

Jan 1, 2006

By Theodore von Rosenvinge

Large diameter (2.4 meter) drilled shaft foundations were installed to depths of over 62 meters through soil into Arkose bedrock for Connecticut?s Pearl Harbor Memorial Bridge (I-95 over New Haven Harbor). The project involved many ?firsts? including the first ?extradosed? cable-stayed bridge in the US, and for Connecticut, the deepest drilled shafts, the first use of a rotator to install shaft casing, and the first use of the Mini-Sid technology for rock socket bottom inspection. Design utilized both friction and end bearing for rock sockets. O-Cell testing was employed to maximize performance factors during design and to allow adjustments to socket lengths during construction. Favorable test results permitted a reduction in socket lengths and significant cost saving.

Jan 1, 2011