Search Documents

By P Marlow

Raiseboring is an attractive method of constructing shafts, being safe, fast and comparatively cheap. But this means back-reaming through weathered ground. However in the gravels and weathered near-surface rocks typical of the Western Australian goldfields, back reaming large diameter shafts through to the surface is risky and conventional sinking from surface has normally been required.An alternative construction approach has recently been used to stabilise the weak surficial materials and allow raiseboring through to the surface. The method is based on first installing rings of non-contiguous reinforced bored piles around the shaft perimeter, for temporary support, then back reaming shafts at full diameter through to the surface. Immediately after the reaming head is removed, the weak exposed materials are supported using remotely sprayed fibrecrete.The method has been successfully applied to four shafts since July 2007; 3 m and 4 m diameter shafts at Trident Mine, a 3 m diameter shaft at Wattle Dam and a 4.5 m diameter shaft at Athena Mine.Bored pile layout designs have varied from eight to 24 piles, of diameters 120 to 270 mm, in one or two rings. In one case, the top 10 m of the proposed shaft was pregrouted. Subsequent surveys have confirmed that fallout occurred in some shafts, out to the ring of piles, implying that the piles inhibited collapse.The practical implementation of the method was not always easy and many valuable lessons have been learnt. This paper documents key aspects of the method and the critical elements for its application.

Mar 21, 2011

By George A. Savanick

The objective of this paper is to review advances in the art of borehole (slurry) mining made by the Bureau of Mines. The introduction gives historical and general background information on borehole mining. The borehole mining concept is defined and justified in terms of economics, health and safety, the environment, and resource conservation. This is followed by a description of the design of a prototype borehole mining tool (BMT) developed by the Bureau of Mines. Included are design drawings and performance specifications. The next section describes the application of the BMT in the extraction of metallurgical coal from steeply pitching seams near Wilkeson, Wash., during 1975-76. The field test showed that the BMT produced coal at the rate of 8 tons per hour (tph) (7,272 kg/hr) from a depth of 88 feet (26.8 m) and was effective in producing coal as far as 15 feet (4.6 m) from the center of the borehole. The data are used as a basis for an economic analysis of borehole coal mining and for the suggestions for the design of a second-generation borehole coal mining tool. The following section describes Bureau efforts in applying borehole mining to the extraction of uraniferous sandstone at Rocky Mountain Energy Corp.'s Nine-Mile Lake site, Natrona County, Wyo. BMT design changes appropriate to uranium mining are described along with production, reliability, and reclamation data taken during 1977-73. The field test revealed that the BMT produced 900 tons (81.8x105 g) of uraniferous sand at an average race of 8 tph (7,272 kg/hr) from a depth of 75 (22.8 m) to 90 (27.4 m) feet and created a cavity 25 feet (7.6 m) in radius. These data are used as the basis for an economic analysis of borehole mining of shallow uraniferous sandstones. Reclamation data included will be the results of backfilling experiments conducted at Nine-Mile Lake during 1978. The most significant of these data were that backfill was emplaced at the rate of 16 tph (14.5x103 kg/hr) and that 90 percent of the material extracted from a cavity can be backfilled.

Jan 1, 1979

By Barber C, Buselli G

Detailed monitoring of point sources of groundwater pollution is expensive due to the high cost of drilling monitoring boreholes. Whether groundwater pollution is due to mining, industrial or domestic waste disposal, a universal difficulty when monitoring groundwater contamination is the placement of boreholes to adequately define the extent of the pollution plume. This paper reports groundwater 'resistivity variations determined from transient electromagnetic soundings at a domestic waste disposal site north of Perth in Western Australia. Together with available hydrogeological and water quality data, the geophysics provides a broad "plume scale" picture of groundwater contamination. A simple three dimensional model of plume development, which takes account of the dimensions of the wastes, has also been developed and shows good agreement with the spread of contamination indicated by the geophysics for relatively small values of the dispersivities. Better estimates of these parameters are still required. The work indicates that a combination of geophysics and modelling with ground-truth data from groundwater quality monitoring of boreholes is required to avoid difficulties in interpretation of data and to better define the extent and migration of pollution in Groundwater.

Jan 1, 1988

By J. B. Newsom

SAFER, cheaper, and faster sinking of mine openings seems to have been realized with the completion of a borehole 5 ½ ft. in diameter and 1208 ft. deep, in Minnesota, during 1938. Moreover, as the opening is to be used solely for ventilation, its circular cross section, smooth walls and freedom from fire hazard recommend it in comparison with the usual timbered shafts of rectilinear cross section. It should be pointed out that a drill hole sunk without the use of explosives frequently will stand open without support, whereas a shaft sunk by standard procedure using dynamite usually must be timbered because of the wall-shattering effect of explosives. The saving in maintenance resulting from the elimination of timber is obvious. The work was done by Pickands Mather & Co. at its Zenith mine, Ely, Minn. This company wanted a ventilation opening capable of delivering 50,000 cu. ft. of air per minute to the fourteenth level, 1200 ft. below the surface. While several general articles1-3 have described the method used, detailed time and performance records have not been presented before. Moreover, with a method as new as this, it is important to compare the results attained under widely varying conditions. Among the new conditions faced at Ely were some extremely hard rock, a series of vertical fractures, seepage water, and some long stretches of sound rock which, combined with excellent equipment, gave a chance to operate without unusual delays. Developments in boring large holes have generally taken the obvious course of increasing the size of the equipment, a line of attack that has resulted in putting down 3-ft. diameter holes at damsites for studying the foundations4 and in drilling ventilation openings between levels at Butte. 5 Such drills operate from the collar of the hole, and the power from the drill is transmitted to the cutting tool through drill rods or pipes. In order to keep down the volume of rock that must be ground to sludge, the cores in large-diameter drilling are made as large in diameter as possible. Their large diameter increases their weight per foot of length, which

Jan 1, 1939

By W. D. Haselton, J. B. Newsom

SAFER, cheaper, and faster sinking of mine openings seems to have been realized with the completion of a borehole 5 ½ ft. in diameter and 1208 ft. deep, in Minnesota, during 1938. Moreover, as the opening is to be used solely for ventilation, its circular cross section, smooth walls and freedom from fire hazard recommend it in comparison with the usual timbered shafts of rectilinear cross section. It should be pointed out that a drill hole sunk without the use of explosives frequently will stand open without support, whereas a shaft sunk by standard procedure using dynamite usually must be timbered because of the wall-shattering effect of explosives. The saving in maintenance resulting from the elimination of timber is obvious. The work was done by Pickands Mather & Co. at its Zenith mine, Ely, Minn. This company wanted a ventilation opening capable of delivering 50,000 cu. ft. of air per minute to the fourteenth level, 1200 ft. below the surface. While several general articles1-3 have described the method used, detailed time and performance records have not been presented before. Moreover, with a method as new as this, it is important to compare the results attained under widely varying conditions. Among the new conditions faced at Ely were some extremely hard rock, a series of vertical fractures, seepage water, and some long stretches of sound rock which, combined with excellent equipment, gave a chance to operate without unusual delays. Developments in boring large holes have generally taken the obvious course of increasing the size of the equipment, a line of attack that has resulted in putting down 3-ft. diameter holes at damsites for studying the foundations4 and in drilling ventilation openings between levels at Butte.5 Such drills operate from the collar of the hole, and the power from the drill is transmitted to the cutting tool through drill rods or pipes. In order to keep down the volume of rock that must be ground to sludge, the cores in large-diameter drilling are made as large in diameter as possible. Their large diameter increases their weight per foot of length, which

Jan 1, 1939

Accounting for borehole damage in analytical modelling of explosively generated stress waves is important for predicting the finer details of the stress wave patterns observed in the field. The classical Sharpe's [19421 concept of an effective borehole larger than the initial borehole diameter has been widely accepted to explain material damage around a borehole. A new analytical model based on dynamic compaction is advanced to predict far-field stress wave patterns. This model supports field data corresponding to reduced frequency of oscillations and increased damping. The present model recovers the earlier result when compaction around the borehole representing borehole damage is ignored.

Jan 1, 1990

By Francisco Sena Leite, Pedro Brito, Gean Frank, PhD Soeiro de Carvalho, Jose, Vinicius Miranda

The consequences of rock blasting with explosives are directly related to the accuracy of drilling and, because they have an effect on fragmentation and ground level, they should be controlled to ensure a problem free production, increase work safety and reduce environment impact. Safety control is one of the most important processes in detonation, since it can compromise the worker security on site and, eventually, neighboring communities. Due to the technology advancements, it is possible to build a hole deviation control device with “of the shelf” parts, and for that reason the authors decided to evaluate the possibility of measuring hole deviation by creating a portable prototype using an electronic sensor capable of measuring the acceleration on objects, that is, to measure the own acceleration of a system, known as "accelerometer" and a micro-controller to handle and treat data. The main idea behind this paper is to validate the power of the Euler method, given the stepping limitations of the sensor and micro controller in order to reproduce of the hole shape. A case study was carried out, comparing the measurements of borehole deviations made by a traditional equipment and the prototype. A mobile application was also created in order to recover and treat and display the data to the user. For validation of the prototype, several holes were measured using the two devices. A residue analysis was used to validate the data obtained. After analyzing and confirming the effectiveness of the new equipment, the normality tests prove a symmetric distribution with null expected residual mean and minimum variance. Consequently, the accuracy of the prototype is evidenced. Thus, the authors aspire to emphasize the potential of using these sensors allied to a traditional numerical method for analysis of hole deviation.

Jan 1, 2019

By David A. Bacca

Hydraulically powered submersible borehole dewatering pumps and emulsion/ANFO blends evolved at about the same time and for the same reasons. Mining operators needed safe, efficient dewatering systems and water resistant products.

Jan 1, 1994

By Kyle Ott, Bernard Daly, Syed Haq, Douglas Anderson, Parsons Brinckerhoff

Drill and blast was determined to be the most cost-effective means of excavating the Raw Water Tunnel (RWT) for the Croton Water Treatment Plant in the Bronx, New York City. One of the major issues confronting project designers was the potential impact of blast vibrations on a major City Distribution Tunnel (CDT). The proposed path of the RWT would cross less than 30 meters (100 feet) above the CDT, which was built in 1917. Discussions with New York City Department of Environmental Protection led to vibration criteria on the CDT of 51 mm/sec (2 in/sec) peak particle velocity as an alert level, and 38 mm/sec (1.5 in/sec) as a review level.

Jan 1, 2012

By J. G. Kelly, C. P. Brown

"In June 1983 a new borehole hoisting system was commissioned at Sherritt Gordon's Fox Mine. Twelve hundred tons-per-day of ore from the 2600 and 2800 levels are being hoisted to the 2000 level through an 8-jt diameter bored winze. This new method replaces the diesel truck haulage system which had been in operation at the mine since 1975.A study was initiated in 1980to determine the most effective method of achieving the required production. The study examined several hoisting alternatives including: expanding the existing trucking system; converting to electrically -powered truck haulage; and deepening the skip compartments of the existing main shaft. The alternative selected as the hoisting method most suited to the requirements was borehole hoisting.Development of the new system commenced in April 1982. Underground excavations included 700 feet of 8-ft diameter borehole, a hoistroom and headframe, storage bins, and a grizzly and rockbreaker station. Equipment installations included: a 5-ft diameter double-drum Nordberg hoist; a counterweighted Kimberley-type skip; two rockbreakers; and the steel sets in the winze. These installations were completed in June 1983. Some problems were encountered after the initial commissioning but these were solved, and since August 1983, the system has proven that the designed capacity is achievable within expected costs."

Jan 1, 1985

By W. R. Dengler, R. S. Brown

In 1974, Brunswick Mining and Smelting Corporation Limited started a 48 million dollar expansion programme at their property in Bathurst, New Brunswick. A portion of the expansion plans includes a 26 foot diameter 4,525 foot deep shaft, underground crusher and conveyor excavations and lower level access development. J. S. Redpath Limited was awarded the contract for the new shaft and associated rock work in May 1974. Brunswick Mining and Smelting Corporation Limited, a member of the Noranda Group, operate this 10,000 ton per day lead, zinc, copper plant with proven reserves in excess of 90 million tons. While most of the ore is provided by the underground operation at the Number 12 ore body, some tonnage is produced from the open pit at the Number 6 ore body. Long range plans indicate a phasing out of the open pit and an increase in production from the underground operation. Existing facilities at the underground mine could not provide additional tonnage, thus the requirement for a new shaft. (Figure 1) The new shaft will also provide access to ore below the 2,800 level which is currently the bottom level of the existing facility. The contract called for sinking a 26 foot inside diameter, nine compartment concrete shaft 4,525 feet deep (Figure 2). Station access and ramp development from existing workings would be required to the bottom of the new shaft. In addition, development work for new crushing and conveying facilities was needed simultaneous with the shaft sinking.

Jan 1, 1976

By Tom Palangio, Ralph M. Olmstead

Video inspection of boreholes with cameras developed specifically for the mining industry is now possible. These designs are reliable, cost effective, and have the flexibility to be used in other applications.

Jan 1, 1998

By Roger L. King

The Bureau of Mines has developed probes to be used in emergency mine rescue operations by being lowered through a borehole drilled into an underground mine. Various probes can provide two-way voice communication with trapped miners, continuous mine atmosphere monitoring, temperature indication, and television searching capability. At present, an infrared imaging probe is being developed for "seeing" through coal smoke.

Jan 1, 1976

By James K. Hallenburg

Geophysical borehole logging is a valuable and inexpensive tool for coal deposit evaluation, development, and production. In addition to the usual determinations of depth and seam thickness, geophysical borehole logs can effectively and accurately determine the coal ash, moisture, and heat contents in situ. Location and evaluation of the partings can be done quickly and accurately. Overburden character determination, such as roof competence, dewatering parameters, ripability, trace element content of the coal and overburden, and sulfur content can be done with existing tools and techniques. The quality of such determinations depends upon the quality of planning and calibration.

Jan 1, 1984

By G. Abramov

The 20th Century saw the modern mining industry enriched by one outstanding method of extracting of mineral resources called Borehole Mining (BHM). Mean while, despite its successful track record in wide ranging locales, few specialists are yet aware of this technology. The intent of this article is to introduce borehole mining to a wider spectrum of drilling and mining professionals. The BHM method is based on in-situ water jet cutting of rock mass. On Fig. 1 the schematic of the method is presented. The borehole mining tool 1 is lowered into the borehole 2 and high pressure water 3 is pumped down. At the bottom part of the tool, one portion of that water comes out through the hydromonitor nozzle 4 in a shape of water jet 5 and cuts the material 6 creating slurry 7. The other portion of high pressure water then comes to the hydroelevator 8 (jet pump, eductor) which produces a vacuum. When the slurry reaches this vacuum zone, the eductor sucks the slurry and pumps it up to the surface, where rock parts are separated from water in a tank 9 or a pond and clarified water is pumped down again closing the re-circulating BHM water supply system. The borehole mining tool is suspended on a drill rig tower 10 which allows the tool to rotate and move vertically along the borehole axis. While extracting rock mass, underground caverns (stopes) 11 are created. If necessary, compressed air 12 can be injected to the raising slurry flow to create an airlift effect. Also, a secondary agent 13 (such as oil, foam, etc.) can be added to the stope through the gap between the tool and the casing. As seen from the illustration, BHM is the remote mining method of extracting of mineral resources through boreholes by high pressure water jets.

Jan 1, 2001

By George A. Savanick

Borehole (slurry) mining, in which a tool incorporating a water-jet cutter and a downhole slurry pump mines phosphate through a borehole, was field tested in northeastern Florida as part of a Bureau of Mines program to increase the domestic availability of critical minerals. Approximately 1700 tons (1.54x106 kg) of phosphate ore were mined at 40 tph (10.1 kg/s) from a depth of 250 ft (76 m). The borehole was filled with water during mining for roof support and to assist slurry pumping. Underwater cutting was enhanced with an air-shrouded water jet. Mined cavities were backfilled to prevent subsidence after abandonment. Roof subsidence during mining was avoided only when the cavity was filled with water. Environmental monitoring before, during, and after mining included hydrological studies and measurements of water quality. Significant water quality changes occurred only in the zone being mined and were confined to the immediate area of the borehole.

Jan 1, 1983

By G. A. Savanick

Borehole (slurry) mining, where a tool incorporating a water-jet cutter and a downhole slurry pump mines phosphate through a borehole, was field tested in northeastern Florida as part of a US Bureau of Mines program to increase the domestic availability of critical minerals. About 1.5 kt (1700 st) of phosphate ore were mined at 23.6 t/h (26 stph) from a depth of 76 m (250 ft). The borehole was filled with water during mining for roof support and to assist slurry pumping. Underwater cutting was enhanced with an air-shrouded water jet. Mined cavities were backfilled to prevent subsidence after abandonment. Roof subsidence during mining was avoided only when the cavity was filled with water. Environmental monitoring before, during, and after mining included hydrological studies and measurements of water quality. Significant water quality changes occurred only in the zone being mined and were confined to the immediate area of the borehole.

Jan 1, 1986

By Gregory Abramov

Borehole Mining (BHM), a remotely-operated waterjet mining method (Figure 1), has recently achieved two major milestones. It was, for the first time, applied to the extraction of manganese ore and at temperatures below freezing. The 1St stage is a demonstration test that is now underway just north of Emily, Minnesota, where the manganese ore is located 100-160m below the surface and its reserves are estimated to be in excess of 500,000 tons. The deposit was discovered over 60 years ago but, due to the fragile and sensitive nature of this Land of 10,000 Lakes (nickname for the State of Minnesota) and strong environmental restrictions, the iron/manganese reserves were deemed unrecoverable and remained untouched until late 2010 when permission for a single-hole demo-test was issued by the local Department of Natural Resources.

Jan 1, 2011

By Marcus A. Wiley, Gregory Abramov

Borehole mining (BHM) is a remotely operated method of extracting rock material through boreholes by high-pressure water jets. Figure 1 illustrates a BHM tool and fluids circulation. The tool consists of at least two pipes, one for pumping down high-pressure water, the second for delivering slurry to the surface. This article reviews the BHM process. It discusses current and new applications for borehole mining and help the readers determine if BHM is applicable in their situations. Previous articles in ME about BHM explained either a particular project (ME, April 2001, pp. 33-36) or a newest patent in this area (ME, March 1991, pp. 313-318). However, neither one provided an overview on the modern BHM technology.

Jan 1, 2004

Provide a means for reliable in situ stress change measurements in soft, friable geologic materials under high stress. Background Effective mine design requires a knowledge of changes in rock stress generated by a mining operation. In situ stress measurement can provide a means of obtaining this knowledge from an active mine for the ultimate purpose of design verification and analysis. The Bureau of Mines has designed and tested a device for measuring changes in rock stress-the borehole platened flatjack (BPF). It has found application in investigating stress anomalies due to geologic structures, stress concentrations from multiple seam interaction, and stress abutments from pillar retreat and longwall mining.

Jan 1, 1990