Search Documents

By Kenneth Etschlager

The ISEE Blast Vibration and Seismograph Section provides a forum for the discussion of issues related to vibration and noise from mine, quarry and construction blasting. The section began as a Technical committee in 1995 to promote the accuracy of blasting seismographs. Currently five subcommittees exist within the section: Seismograph Standards; Seismograph Testing and Calibration; Vibration Limits, Technical; Vibration Regulations; and Program and Communications. Foremost, the Seismograph Standards section wrote the first two technical standards adopted by the ISEE. The historical accomplishments, current activities and objectives of the section are discussed.

Jan 1, 2003

By Moore A. J, Evans R

Blast vibration control and assessment techniques have been developed which supplement traditional charge mass scaling methods. The improved techniques, which can be used to predict air and ground vibration levels at the planning stage, and to assist in the control of blasting operations, have reduced the level of operating risk concerning blast vibration. In addition to such factors as charge mass, distance and blast vibration levels, these additional techniques take account of orientation of the blasting face, topographic shielding, wavefront reinforcement, and meteorological conditions. They have assisted in compliance with specified blast vibration levels for environmental licence and mining lease conditions, the reduction of blast vibration nuisance to residents in the area surrounding a mine, and control of building and rock structure response in adjacent areas on the mine lease area.

Jan 1, 1994

By Moore A. J

This paper describes the use of a wavefront reinforcement model which has been developed to supplement established charge mass scaling methods. The model allows for the time taken for blast vibration wavefronts to travel from each blasthole, and has been successfully used to explain the reason for directional increases in both air and ground vibration in certain situations. The model has been used to identify wavefront reinforcement due to the propagation of air vibration and ground vibrations in certain situations. The paper includes a throw (or cast) blasting case history which provides multi-station evidence of the strong directional nature of wavefront reinforcement.

Jan 1, 1995

By Gordon M. Matheson, David K. Miller

Possible impacts to the water quality and production capacity of ground water supply wells by blasting is a common cause of complaints for blasting contractors, mining companies, and local regulatory authorities. The major complaints of changes in well water quality include; turbidity, discolored water (red, brown, black, yellow and milky water), and nitrate and/or coliform contamination. The major complaints for changes in well water production capacity include: loss of quantity production, air in water and/or water lines, damage to pump, and damage to well screen or borehole.

Jan 1, 1997

By Douglas A. Anderson

The US Bureau of Mines, in RI 8507, has shown that blast vibrations at low frequency are more likely to cause damage and complaints than those at higher frequency. Since that publication in 1980, the Office of Surface Mining and many state and local regulatory authorities have incorporated frequency in their regulations for acceptable ground vibration from blasting. Even when frequency is not explicitly stated in regulations, it may become an issue in hearings or in court.

Jan 1, 1992

By Drew Martin

In March 2010 the Boral Linwood Quarry, Adelaide South Australia, implemented the blasting contractors Monte Carlo Blast Vibration Model as part of their blast design process. The Linwood Quarry was developing an area where blasting activities were marginally complying with the statutory vibration limits. Compliance to the statutory limits was only being achieved through the use of small blasts (less than 15 000 T (14 763 ton)) at a high cost to the quarry.

Jan 1, 2012

By W. J. Birch, R. Farnfield

Nuisance caused by perceived high vibration levels as a result of blasting on quarries and opencast coal mine is now the number one environmental concern of residents living adjacent to such operations. The intrinsic nature of blast vibration monitoring and prediction is that it is impossible to accurately forecast the vibration levels that will be experienced by a given blast at a given location. Thus it is that a statistical approach to the problem is the only viable option. Unfortunately, persuading local residents living adjacent to a project that requires blasting that this is the best way of safe guarding both their homes and their quality of life is not an easy task. Thus routine monitoring involving both operators and regulators play a key role in building trust. However, public confidence is often shaken when regulators and operators use two different blast monitoring instruments side by side to record a blast at a local resident’s house and arrive at different results. To make certain that this does not happen in future, what is needed is a protocol that ensures that any two different blasting seismographs give the same peak particle velocity values at the same observation point. To do this all the equipment manufacturers, regulators and relevant professional explosive engineering bodies need to be involved.

Jan 1, 2014

During underground mining, rock mass changes can occur as a function of the mining sequence and excavation processes. Mining-induced rock mass damage can occur due to redistribution of static stresses and the application of dynamic stresses from blasting and seismic activity. These rock mass changes can result in a degradation of strength of the bulk rock mass and the remaining rock surrounding existing excavations. Rock mass damage near existing excavations which lead to excavation-scale instabilities such as rock fall, excavation closure, or visible rock mass fracturing can detrimentally affect the safety and profitability of mining operations.The focus of the current work was the prediction and assessment of damage to mine infrastructure occurring in relation to the blasting of a sublevel open stope. The study case involved a 60kt stope located in a highly-competent rock mass at a large Australian sublevel open stoping mine. The mine infrastructure of interest for investigation included local stope access development, critical access and haulage development crossing a regional-scale fault, an explosives storage magazine and a ventilation return air raise. The methods used to predict or assess the blast-induced damage to each infrastructure element in response to stope extraction were:- intact rock strength testing,- discontinuity mapping,- linear-elastic static stress modelling,- blast-damage mapping,- near-field blast vibration monitoring and analysis,- geophysical assessment using inferred stiffness and wave velocity methods, and- post-extraction void assessment.The results of the detailed blast damage prediction and assessment program at the mine site have been discussed by the primary author elsewhere (Fleetwood, 2010). The current work will address blast-induced damage to mine infrastructure as a result of extraneous blasting vibrations from stope production blasting. A method for predicting the amplification of excavation surface motions from reflecting body waves will be discussed as well as the results of damage mapping around the study stope. The results of the damage mapping program identified blast-induced damage that occurred to the surface of the explosives storage magazine and local stope access development. No damage was observed at the main fault crossing or return air raise where higher vibration amplitudes were measured or predicted.

Dec 6, 2010

By D. Lee Petersen, Travis Davidsavor

The 2003-2004 expansion of a Duluth medical center required rock blasting adjacent to the existing structures, a Mn/DOT retaining wall and other urban structures. This case history describes the methods of a blast damage assessment, based on blast parameters, excavation locations, and critical vibration receptors (including surgical suites, a linear accelerator and a major retaining wall). The assessment concluded that blast vibrations could be controlled, by limiting charge weight, to eliminate impact at the critical receptors. Prior to construction, we conducted preconstruction surveys on structures susceptible to vibration damage. During construction, we reviewed submittals, observed test blasts, reviewed blasting logs and monitored blasting vibrations. Up to 13 seismographs were used simultaneously. Close coordination with medical center operations personnel was necessary to prevent impacts to critical medical procedures. Measured vibrations were clustered around the predicted values, and attenuated at the predicted rate. High-frequency blast induced ground vibrations induced low-frequency vibration of an adjacent MnDOT retaining wall. Medical center structures were observed to significantly attenuate the ground-borne vibrations. This paper was first published in the Proceedings of the 56th Annual Geotechnical Engineering Conference, 2008, at the University of Minnesota.

Jan 1, 2010

In order to satisfy environmental and mine operational requirements it is becoming increasingly important to minimise ground blast vibrations at certain locations. These locations are often in soil or on large resonant structures such as grain silos, highway bridges or even the walls of an open pit. A soil monitoring exercise was carried out to evaluate the common practice of coupling vibration detectors to the ground using spikes. At a series of locations in an operating quarry the spiked array response to single blastholes was compared with that of an accelerometer array attached to a calibrated embedded mount. The results clearly showed that the spiked arrays over-estimated the true ground vibration by 46.5 per cent on average, with a maximum observed error of 99.2 per cent. These errors are considered too large for compliance monitoring where accurate vibration levels are required for comparison with prescribed limits. Although spike coupling is convenient, its use for compliance monitoring should be viewed with caution. Unfortunately, however, many manufacturers supply their detectors as spiked arrays. A structural monitoring exercise was also carried out to evaluate the vibration response of a grain silo, highway bridge and a pit wall to the initiation of single blastholes. In this case accelerometers and standard geophones were firmly attached to the bridge which resonated at low frequencies. The results clearly show that, due to their limited low-frequency response, the geophones typically measured only half the true vibration level as measured by the accelerometers.

Jan 1, 1995

Blast vibration analysis under relatively near-field conditions has been carried out in a narrow-vein underground operation. The objective was to characterize the vibration signal (particle acceleration and velocity) from carefully controlled stope blasts. The limitations of such analysis in deriving design guidelines for reducing dilution has been elucidated. It has been shown that identification of each individual hole with specific explosive types can yield explosive-specific predictive equations for particle velocity. This has been coupled with measurement of actual overbreak to arrive at a limiting vibration level to generate a realistic design tool for controlling dilution in narrow-vein mines.

Jan 1, 2003

By Charles Dowding, Cathrine Aimone-Martin

This article summarizes an investigation of the structural response of a brick façade home in New Mexico. The subject Ricter residence was located some 1100 to 1400 ft away from an aggregate quarry, and was subjected to a maximum peak particle velocity and air blast over pressure of 0.29 ips and 122 dB, respectively. Superstructure (corner) and mid-wall responses to blasting and human induced activities were measured. An existing exterior crack in the brick work was instrumented to measure crack width response to blasting, human induced activities, and environmentally induced changes in temperature and humidity. Crack and structure response data were correlated with ground velocity and airblast excitations. Amplification of ground motions at the upper structure were calculated and compared with values for typical wood frame structures. The natural frequency and damping characteristics of the structure were determined to compare with measured amplification values. Wall strains produced by bending and inplane tension strains were computed from upper corner structure response and compared to failure strains for drywall and brick veneer. Calculated strains were found to be far lower than those required to crack brick and environmentally induced crack response was found to be far greater than that caused by blast induced ground motion or airblast overpressures

Jan 1, 2005

By Willard P. Ward

SOME TIME in the year 1874 or 1875, I conceived the idea that spiegeleisen might be made -in a blast furnace from ores that were not carbonates, and which did not contain both manganese and iron in the same ore. Up to this time, such ores had formed the basis of all the spiegel that had been produced; and all the ferromanganese that was on the market before 1875 was made in crucibles, and cost about 00 per ton, for 80 per cent. Mn. I consulted the great steel metallurgist of the day, Alexander Holley, who listened attentively to what I had to say, and told me he did not think my plan was practical, so I abandoned it for the time being. But I was so stubborn that I could not get the notion out of my head. It seemed to me that a good metallurgist should be able to work the thing out in some way. I had already had some experience in smelting refractory lead ores in Utah, and was young and not lacking in self confidence, so after waiting a bit, I got Anton Eilers, the best all-around metallurgist I knew, and J. H. Bramwell, the best iron blast-furnace man I knew, both intimate friends of -mine, to come to my place in Bartow County, Georgia, and look over things. They remained for several days, and made all the examination they thought necessary; and they also advised me to give up the project, and either to keep the furnace running on car-wheel iron or to blow it out. After my talk with Holley, I improved my plant in several ways. I closed the top of the furnace, put in a hot-blast stove, a steam boiler and a Weimer blowing-engine which gave me blast enough, at a pressure high enough for all the requirements of, the furnace, and which I could bring up to a temperature of 600° to 700° F.

Jan 1, 1921

By C. C. Furnas

IT is well known that particles of different sizes are not distributed evenly throughout the average charge in an iron blast furnace. Just how great the disparity in particle size in different parts of a single plane in a furnace may be is indicated by the results of some recent investigations1 conducted by the Bureau of Mines on a furnace operating on Lake ores. The wide variations found in gas velocity, gas composition, and temperature from the periphery to the center of the upper charge column were caused by the great variation in particle size of the raw materials used and were also greatly influenced by the methods of charging. This paper summarizes the results of an investigation of the influence of different methods of charging and of the treatment of raw materials upon the size distribution of the solid particles in the blast furnace. A more complete report will appear later as a Bureau of Mines technical paper.

Jan 1, 1929

By Chas. B. Dudley

A Discussion of the papers of Mr. James Gayley, on "The Application of the Dry-Air Blast to the Manufacture of Iron," and of Mr. J. E. Johnson, Jr., on "The Physical Action of the Blast-Furnace," by Messrs. Charles B. Dudley, R. W. Raymond, J. E. Johnson, Jr., William F. Mattes, James Gayley, David Baker, John Birkinbine and F. E. Bachman. (Washington Meeting, May, 1905.) CHAS. B. DUDLEY, Altoona, Pa.:-Pam not a blast-furnace man, and this always puts me it a disadvantage because I cannot go into the details of the making of iron and steel. I have not the experience, and have to take the statements of other people, so what I say regarding the subject of this paper is not in the sense of an expert. When I first heard of Mr. Gayley's experiments, I said to myself, " I fear they will result in failure, since, apparently, Mr. Gayley has forgotten one chemical fact, namely, that carbon does not combine with oxygen in the absence of water-vapor." This fact which was so astonishing when it was first brought out some years ago, and which those who are interested may find in the Journal of the Chemical Society of London, for 18S5, page 349, and 1894, page 611, led me to think that the drying of the air would be a mistake. The general subject of the influence of water-vapor on chemical action is a large one; but the special point in which we are for the moment interested, namely, the influence of water-vapor on the combustion of carbon, was especially treated by Mr. H. B. Baker, in the papers referred to. Apparently, however, as the result of Mr. Gayley's experiments, we are to learn that the amount of moisture still left in the desiccated air is sufficient to secure perfectly satis¬factory combustion. In thinking over Mr. Gayley's paper, it occurred to me that there were two alternatives, either of which might be chosen, namely, we might dry the air as Mr. Gayley does, or possibly we might, in a very much simpler way, simply saturate the air at a constant temperature, and thus get uniform working and

Sep 1, 1905

By J. A. Brothers, M. R. Foran

"AbstractThis paper reviews the progress made in the manufacture of hydraulic cement from iron blast-furnace slag by simply grinding the granulated material with other constituents. The influence of the chemical and mineralogical composition of the slag, the conditions of granulation, the manner of drying, and the fineness of grinding, on the hydraulic properties of the cement, is discussed. The effect of additions of lime, portland cement, and anhydrite, alone and in combination, on the physical and cementing qualities of the mortar and concrete made from Sydney blast furnace slag, is shown in tables of data and is reviewed in some de- tail. The work at the Nova Scotia Technical College has shown that a cement equivalent in every respect to portland cement can be made from basic blast furnace slag- by the us2 of certain quantities of portland cement as an activator.IntroductionBlast furnace slag is a potentially valuable material for the manufacture of hydraulic cement. It is a by-product of the manufacture of iron in the blast furnace, and is formed by the combination of the silica and alumina .of the iron ore with the limestone flux. The metallurgist terms a slag .acid or •basic according as the percentage of lime is less or greater than the percentage of silica plus alumina. The basic slags have the •more pronounced hydraulic properties."

Jan 1, 1950

By Dale Preece, Ayman Tawadrous

This paper presents a number of examples of three-dimensional blast modeling in both surface and underground environments that include time-delay explosive decking. These examples include: 1) quarry blasting, 2) coal seam protection blasting, 3) mineral mine blasting with high energy time delayed decks, and, 4) underground single-level/single-shot drawbell blasting.

Jan 1, 2014

By K. M. Kim

An analysis was conducted to determine the effects of blasting on slope stability and downstream comminution processes. To investigate these effects, the extent of blast-induced rock damage and the magnitude of induced stress were examined. This analysis showed that damage may extend up to 500 m (1 MPa, tensile strength) into the rock mass, a distance that is sufficient to have an impact on the pitscale slope over the long term. In addition, the damage zone was calculated using the assumption that compressive waves are the primary agent in microfracturing during blast fragmentation. The calculated damage zone — up to 2.2 m (43 MPa, rock mass compressive strength) — indicates that microfracturing can occur throughout 20-50% of the entire rock mass in the blasting area, depending on the blast geometry, burden and spacing. Finally, an economic analysis was conducted by comparing two assumed blasts in a copper mine. The change in energy required for crushing and grinding was demonstrated using Bond’s law after increasing the blast energy from 180 kcal/t to 350 kcal/t. A total cost saving of 13.3% ($9.4M) was achieved with the increase. However, the benefits of blast-induced microfracturing must be balanced against the potential impacts to slope stability to ensure safe conditions, a top priority in mining operations.

Jan 1, 2014

By K. Kim

An analysis was conducted to determine the effects of blasting on slope stability and downstream comminution processes. To investigate these effects, the extent of blast-induced rock damage and the magnitude of induced stress were examined. This analysis showed that damage may extend up to 500 meters (1MPa, tensile strength) in the rock mass, a distance that is sufficient to impact the pit-scale slope over the long term. In addition, the damage zone was calculated using the reasonable assumption that compressive waves are the primary agent in microfracturing during blast fragmentation. The calculated damage zone ? up to 5.6 meters (30MPa, 30% of the compressive strength) ? indicates that microfracturing can occur throughout the entire rock mass in the blasting area. Finally, an economic analysis was conducted by comparing two reasonably assumed blasts in a copper mine. The change in energy required for crushing and grinding was demonstrated using Bond?s law after increasing the blast energy from 180kcal/t to 350kcal/t. A total cost saving of 13.3% ($9.4M) was achieved with the increase. An optimal blast design should consider both slope stability (safety) and downstream comminution energy (production).

Feb 23, 2014

By Hesam Dehghani, Farid Alimohammadnia, Nima Babanouri, Mokhtar Kalhori

In open-pit mining, blasting pattern design is performed to achieve a desired degree of fragmentation for loading, hauling, and crushing operations. Inappropriate fragmentation of rock will result in numerous problems such as incurring extra costs for secondary blasting, production interruption, etc. Wetness of the blast holes is one of the most important factors, which can cause the inappropriate rock fragmentation. Lowering ambient temperature in the vicinity of the explosion, the presence of water in the hole adversely affects the quality of the explosive while dissipating part of the explosion energy, ending up with inappropriate fragmentation problems. In the present research, in order to study blast-induced fragmentation conditions in Baba-Ali Iron Ore Mine, three scenarios were considered: explosion of ammonium nitrate with fuel oil (ANFO) in dry hole, explosion of ANFO in wet hole, and explosion of the emulsion in wet hole. For this purpose LS-DYNA, a numerical simulation code was used. Results of the present research showed that, compared to the explosion of ANFO in wet hole, the explosion of the emulsion produced more uniform distribution of fragment size, while the explosion of ANFO in dry hole resulted in fewer large fragments.