Search Documents

By M. Ahlers, Horace Pops

Slip features and formation of stress-induced mm-tensite have been studied in single crystals of fl phase Cu-Zn alloys in the composition range between 43 and 48 at. pct Zn. A phenomenological analysis is presented in which the glide planes and directions that me associated with the inhomogeneous shear in the martensite phase are predicted from the experimentally determined habit planes and macroscopic shear directions. It is shozun that the resolved shew component of the applied stress on the secondary shew system is a very important factor governing the formation of stress-induced martensite. A comparison is made between martensitic phases that form spontaneously upon cooling and those phases that arise from deformation. THE ß phase in Cu-Zn alloys is unstable and may transform spontaneously by a martensitic transformation1-3 during cooling. Thermoelastic and burst-type spontaneous martensitic phases have been observed3 in the composition range between 38 and 42 at. pct Zn. Martensite forms in alloys containing more than 42 at. pct Zn only by cold work below a temperature denoted as Md.4 Thus, alloys near the equiatomic composition can undergo a stress-induced transformation upon cold work at room temperature. Although data have been obtained concerning the effect of temperature5 and composition4 on the deformation of polycrystalline Cu-Zn alloys, it is rather surprising that few detailed studies6-8 on 6 brass have been conducted for single crystals where the stresses acting on crystallographic planes can be determined. A thorough understanding of transformation mechanisms requires knowledge of the role of stress and plastic strain. With this objective in mind we have made an investigation of the stress-induced rnartensite transformation in single crystals of 0 brass in the composition range between 43 and 48 at. pct Zn. Particular emphasis is given to the morphology and crystallographic features and a comparison is made between stress-induced and spontaneous martensite. I) EXPERIMENTAL PROCEDURE Master alloys having nominal zinc contents of 43, 45, and 48 at. pct were prepared from spectroscop-ically pure metals (>99.999 pct) in sealed quartz tubes under a partial pressure of helium. These alloys were cut into several pieces and converted into small rods by melting in quartz tubes. Subsequently, single crystals were grown from the rods by the Bridgman technique and homogenized for 3 hr at 820°C. Lattice parameter measurements were made from stress- relieved filings. Compositions, as determined from the reported variation of lattice parameter with atomic percent zinc,' indicated a zinc loss of less than approximately 0.25 at. pct. The single crystals were electroturned using a phosphoric acid electrolyte into tensile specimens each with a center section of 1 mm diam and 1 cm gage length. Cylindrical specimens approximately 3 mm in diam and 10 mm long and spark-machined rectangular blocks approximately 3 by 3 by 10 mm were prepared for compression studies. These blocks were stress-relieved and electropolished to eliminate any stresses introduced by spark machining. Crystal orientations were determined to an accuracy of ±2 deg primarily from back-reflection Laue photographs, and sometimes by the rotating single-crystal method. Figs. 1 to 3 show the location of the tension and compression axes within unit stereographic triangles. All specimens were deformed plastically at room temperature using an Instron machine, the crosshead speed being 0.02 or 0.05 cm per min. A hard steel hemisphere was placed at the upper end of the compression samples to achieve uniaxial loading. Trace normals of slip markings and habit planes of strain-induced martensite were determined to an accuracy of ±4 deg from the rectangular blocks by a two-surface analysis and from cylindrical specimens by measuring the angle between the tensile (or compression) axis and the tangent to the surface trace for different rotations about the deformation axis. Slip

Jan 1, 1969

By H. I. Aaronson, C. Laird

The kinetics of thickening and of lengthening of ?' plates in an Al-3.93 pct Cu alloy in the temperature range 203" to 300" C were determined by means of transmission electron microscopy. The rate of thickening was found to be less than that allowed by volume diffusion control at all temperatures, by amounts which increased with decreasing temperature, in agreement with the predictions of a general theory of precipitate morphology.1 Thickening was treated on the basis of the ledge mechanism. Ledges were deduced to spread across the broad faces of ?' plates at volume dzjrfusion-controlled rates, as anticipated from the disordered structure of their edges. Lengthening of 8' plates, on the other hand, took Place more rapidly than allowed by volume dzjrfusion. This occurred despite clear morPhological evidence of a bmrier to growth at the edges of these plates. It was concluded that the misfit dislocation structure comprising the barrier requires that lengthening take place by a jog mechanism. The tnisfit dislocations, however, also serve as diffusion short circuits, and allow high overall lengthening rates to be achieved. In Part I' it was shown that, within the range of aging temperatures and times studied, the broad faces of 8' plates formed in Al-4 pct Cu are fully coherent with the a, matrix. Virtually .all of the dislocations present in these faces were found to have developed as a result of plastic deformation in the a phase. Such dislocations are thus "intruders", rather than the more usual misfit-compensating variety. The edges of 8' plates were confirmed, by extension of the earlier studies of Mat-suura and Koda,3 to be made up of edge-type misfit dislocations, in sessile orientation with respect to lengthening of the plates. These interfacial structures should cause 8' plates to thicken and to lengthen at rates less than those allowed under the condition of volume diffusion control, such as would be expected if the interphase boundaries had disordered structures.' The narrow width of 8' plates, the reproducible crystallography of their broad faces, and the appearance of these plates in cross section as octagons rather than as circular discs2 provide qualitative support for these deductions. The present study of the rate of thickening and the rate of lengthening of 8' plates was undertaken in order to examine them on a quantitative basis. I) THICKENING KINETICS OF THE BROAD FACES OF?' PLATES A) Literature Review. The measurements now available on the thickening kinetics of single-phase precipitate plates consist of one plot of the thickening of a proeutectoid ferrite plate in an Fe-C alloy,' showing (as predicted) thickening rates less than those allowed by volume diffusion control. B) Experimental Procedure. Details of the preparation of the 4-3.93 pct Cu alloy used in this study have been previously reported.4 As in Part 1,' transmission electron microscopy was the observational tool employed. A general description of the apparatus and procedures of the electron microscopy studies is given in Section I of Part I. In thin foils, 0' plates tend to form at and parallel to the foil surface.' A direct investigation of the thickening process by means of hot-stage transmission electron microscopy was therefore not feasible. It was thus necessary to use the conventional method of aging individual bulk specimens for a wide range of different times at the various temperatures studied. In each specimen, the thicknesses of a number of plates were measured. Since thin foils prepared from "bulk-aged" material contain a large proportion of grains with orientations near (001) , it was relatively easy to find, near the edges of the foils, the characteristic multifold patterns of intersecting extinction contours which indicate regions where the foil is exactly at an (001) orientation. The thicknesses of large numbers of plates were measured along the (200) branches of the "stars" so that the 8' plates were precisely parallel to the optical axis of the microscope. Wherever possible, intersecting extinction contours were adjusted with the parameter s > 0 to improve the visibility of the plates in bright-field illumination. These precautions, in combination with taking the measurements at the thinnest parts of the foils, minimized the errors in the measurement of the thickness of the plates resulting from inexact parallelism to the electron beam. Since the plates were very thin, it was not easy to measure their thickness on the photographs. The techniques of enlargement and of microdensitometry were employed to minimize errors from this part of the measurement. A further source of possible error, that the plates can appear thicker because of contrast associated with mismatch normal to the plane of the plate, was also considered. The images of the plates were usually thinner than those of dislocations, however, and no anomalous changes in apparent plate thickness were observed when regions of foil containing plates were tilted through various diffracting conditions. Any error from this cause must therefore be small. Other sources contributing errors were: a) the microdensitometer traces per se and the subjective estimates of their peak limits, and b) slight fluctuations in magnification associated with small changes in the current of the objective lens of the electron microscope. The overall error probably amounted to no more than 5 to 10 pct. In order to obtain readily interpretable data on thickening kinetics, it is essential that the diffusion fields of adjacent ?' plates not be allowed to overlap. Calculations'-' showed that this condition is definitely not ful-

Jan 1, 1969

By F. D. George, M. J. Salkind

Al3Ni whisker-reinforced aluminum was found to exhibit good Charpy impact toughness and little notch sensitivity even though its room-temperature tensile elongation parallel to the whiskers is only 2 pct. This impact behavior was maintained d liquid nitrogen temperature (-196"C). It is postulated that this behavior is due primarily to the presence of the continuous aluminum matrix which provides sufficient 10calized ductility in the vicinity of the crack tip to absorb considerable energy from the advancing crack. The impact behavior of Al-Alni was found to be quite anisotropic. Of six orientations studied, the transverse orientation having the notch normal to the whisker axis was found to exhibit the lowest impact energy, whereas the transverse orientation having the notch parallel to the whisker axis was found to exhibit the highest impact energy. A significant differnce was noted between the impact behavior of material containing needlelike whiskers and that containing bladelike whiskers. Only two of the six orientations studied exhibited complete fracture for the material containing needlelike whiskers. On the other had, most of the specimens containing bladelike whiskers exhibited complete fracture. It was postulated that the bladelike whiskers block transverse flow, thus reducing the amount of plastic deformation ahead of the crack tip. One of the more significant advantages of composite materials is the prospect of combining high strength with toughness. In general, toughness is associated with materials which exhibit considerable ductility and can deform plastically in the presence of a stress concentration. Very strong materials which resist plastic deformation generally exhibit low toughness. At first glance, then, it would appear as though strength and toughness are mutually incompatible so that useful engineering materials would have to be a compromise between the two. One approach to the problem of combining the high intrinsic strength of ceramics with the toughness of metals was to mix them together to form a cermet. Unfortunately, the toughness of cermets was found to be rather disappointing. Whisker reinforcement of metals, however, appears to be a more promising approach. It has been demonstrated that whisker-reinforced metals produced by unidirectional solidification exhibit enhanced strength due to the presence of high strength nonmetallic whiskers. The total strain capacity of these composites in the direction of fiber alignment is limited to that of the fibers, the matrix being unable to carry the load once the fibers have failed. A characteristic, then, of whisker composites is low ductility in the direction of whisker alignment, on the order of a few percent elongation. This low elongation, which is usually associated with brittle behavior, should not be taken as an indication of low toughness. Such a material can exhibit significant ductility in directions other than parallel to the fibers7 and can therefore possess significant intrinsic toughness. Toughness in a fiber-reinforced metal is derived from several mechanisms. The first is due to the toughness of the matrix itself. A continuous ductile metal matrix can act as an effective crack arrest medium by undergoing localized plastic deformation. Cracks initiated from the surface of the composite or from a brittle fiber failure must travel through the matrix before reaching another brittle phase particle. A second crack arrest mechanism peculiar to fiber composites is due to the fact that, as a crack travels through the matrix and approaches a fiber, the plastic deformation ahead of the crack tip will result in loading of the fiber. This causes the matrix shear strength in the plastic zone to be apparently higher, thus extracting more energy from the crack and diverting the crack at an angle to the original direction of propagation. A third crack arrest mechanism occurs in fiber composites which exhibit a weak bond between fiber and matrix. The idea was proposed by Cook and Gordons that if a crack propagating transversely in a fiber composite were made to turn and run along the fibers by decohesion of the fiber-matrix bond, then toughness would be imparted by the blunting of the crack tip and the creation of new surfaces. The last mechanism, interfacial decohesion, is commonly noted in naturally occurring fiber composites such as wood, bone, and bamboo, and has been observed in man-made composites such as glass fiber-reinforced resins,g silica fiber-reinforced aluminum," laminated steel," and tungsten and silica fiber-reinforced electroplated copper.'' The first mechanism, crack arrest by plastic deformation in the matrix, has been noted in tungsten wire reinforced cast copper." The purpose of this investigation was to quantitatively assess the toughness of a whisker-reinforced metal as a function of orientation. Previous investigation considered only cracks propagating nominally perpendicular to the reinforcement. In this investigation, crack propagation in three mutually perpendicular directions as well as three intermediate orientations was investigated. The system chosen for study was the unidirectionally solidified A1-A13Ni eu-tectic alloy which has a microstructure consisting of 10 pct by volume of A13Ni whiskers in a matrix of aluminum This material exhibits two different kinds of whisker morphology, depending upon the rate at which it is solidified.' At low rates of solidification (less than 2 cm per hr) the whiskers are bladelike, whereas at higher rates of solidification they are

Jan 1, 1969

By R. A. Vandermeer, J. C. Ogle

The preferred crystallographic orientations (texture) developed in randomly oriented, poly crystalline niobium during rolling were studied by means of X-ray diflraction techniques. The evolution of texture at both the surface and center regions of the rolled strip was carefully examined as a function of increasing defamation throughout the range 43 to 99.5 pct reduction in thickness. Certain aspects of the center texture development in niobium are in agreement with the predictions of a theory by Dillamore and Roberts, but others cannot be explained by the theory in its present form. Above 87 pct reduction by rolling, a distinctly different texture appeared in the surface layers which was unlike the center texture. The present results are compared with previous results obtained from other bcc metals and alloys. RANDOMLY oriented, poly crystalline metal aggregates when plastically deformed to a sufficiently large extent develop preferred orientations or textures. In a recent review article, Dillamore and Roberts1 pointed out that the nature of the developed texture may be influenced by a large number of variables. These include both material variables such as crystal structure and composition and treatment variables such as stress system, amount of deformation, deformation temperature, strain rate, prior thermal-mechanical history, and so forth. From a practical point of view, the control of preferred orientation may often be important for the successful fabrication of metals into usable components. During the past few decades many experiments have been devoted to the study of deformation textures. This work, however, has been confined in large part to metals and alloys that have an fcc crystal lattice. By comparison, bcc metals and alloys have received much less attention, and consequently our understanding of preferred orientations in these materials is only shallow. This state of affairs worsens when it is realized that almost all of our present howledge about this class of materials derives from studies on irons and steels.' The bcc refractory metals, which are relative newcomers to the industrial world, have, on the other hand, been given at best only passing glances in the area of texture development. Our understanding of the evolution of preferred orientations in bcc metals can only remain fairly limited until systematic studies of metals and alloys other than the irons and steels have been carried out and the influence of the many variables has been determined. To that end a program was initiated to investigate in detail texture development in niobium. The present paper reports some of the results of this study. Textures were determined at both the center and surface of strips rolled variously to as much as 99.5 pct reduction in thickness at subzero temperatures. Emphasis in this paper is on texture description and on texture evolution during rolling to progressively heavier deformation. EXPERIMENTAL PROCEDURE The niobium was purchased from the Wah Chang Corp. as a 3-in.-diam electron-beam-melted billet. Chemical analysis indicated the impurities to be less than 300 ppm Ta, 40 ppm C, 10 ppm H, 170 ppm 0, and 110 ppm N. All other impurities were below the limits of detection by spectrochemical analysis. This large-grained billet was fabricated into specimen stock so that a fine-grained randomly oriented grain structure resulted. This was accomplished in three deformation steps alternated with recrystalli-zation anneals of 1 hr at 1200°C in a vacuum of low 10"6 Torr range after each deformation step. The first step was to alternately compress the billet 10 to 20 pct in each of three orthogonal directions. The second step was to compress in only two directions 90 deg apart to produce a 2-in.-sq bar. The final step was to roll this bar 50 pct to give a 1-in. by 2-in. cross section. After the final anneal, metallo-graphic examination showed the material to have an average grain size equivalent to ASTM No. 5 at 100 times (i.e., 0.065 in. diam). Specimens cut from the center and edges of this bar gave no indication of detectable preferred orientation when examined by X-ray diffraction. Samples 1.5 in. long, either 0.625 or 0.750 in. wide, and approximately 0.400 in. thick were machined from this fabricated ingot. The surfaces corresponding to the rolling planes were ground so as to be parallel. The samples were chemically polished in a solution of 60 pct nitric acid and 40 pct hydrofluoric acid (48 pct solution) prior to rolling to remove any cold work introduced in the machining operations. Rolling was accomplished with a 2-high hand-operated laboratory rolling mill that had 2.72-in.-diam rolls. Prior to operation, the rolls were polished with 600 grit paper, cleaned with acetone, and then soaked in a container of liquid nitrogen for several hours. The samples were also soaked in liquid nitrogen prior to rolling and were recooled between each pass. While some slight heating of the samples occurred during rolling, this procedure maintained the sample temperature well below 0°C at all times. The samples were rolled unidirectionally, and the rolling plane surfaces were not inverted during any phase of the operation. The draft per pass averaged between 0.010 to 0.012 in. After 96 or 97 pct reduction the draft was reduced to 0.001 to 0.002 in. per pass. Samples were rolled to various reductions in thickness between 43 and 99.5 pct.

Jan 1, 1969

By R. D. Daniels, T. G. Oakwood

A study was made of the effects of small quantities of hydrogen on the mechanical properties of colum-bium. Tensile specimens, hydrogenated to concentrations of 20 to 200 ppm, were tested at temperatures of 300°, 191°, and 77°K. Although hydrogen was found to have little effect on the strength of columbium, the ductility of Cb-H alloys was found to be quite sensitive to both hydrogen concentration and temperature. At 300°K, an abrupt loss in ductility occurred at a critical hydrogen concentration, although some ductility was observed beyond the tolerance limit. A similar result was found at a lower hydrogen concentration at 191°K. At 77°K, however, a more gradual loss in ductility with increasing hydrogen concentration was observed. Hydrogenated columbium was thus observed to undergo a ductile-brittle-ductile transition. Metallographic examination of fractured specimens revealed extensive porosity at both 77° and300°K which was a distinct function of hydrogen content. At 191°K, although some secondary cracking was noted, the amount of observed porosity was minimal. These observations are interpreted in terms of hydrogen solubility and mobility as a function of temperature and in the role of hydrogen in promoting growth of microcracks. lHE effect of hydrogen on the mechanical properties of the refractory metals is not, at present, completely understood. A number of studies have shown these materials to be susceptible to hydrogen embrittlement. Roberts and Rogers1 have found that vanadium can be embrittled by hydrogen. It was further demonstrated that fracture undergoes a ductile-brittle-ductile transition as the temperature is lowered from 150° to -196°C; i.e., there is a ductility minimum observed at a certain temperature. The ductility is increased by either raising or lowering the temperature from this point. A more complete study by Eustice and Carlson2 on vanadium containing 10 to 800 ppm placed the ductility minimum at about -100°C with variations reportedly due to hydrogen content and strain rate. Ductility minima have also been found at certain temperatures for tantalum containing 7 ppm H3 and 140 ppm H.4 At hydrogen concentrations above 270 ppm, however, the ductility return at low temperatures was considerably reduced.4 In the case of columbium, some disagreement exists in the literature. Eustice and Carlson,5 Wilcox et al.,6 and Imgram et al.4 failed to find a ductility minimum although a composition-dependent ductile-brittle transition was observed. Hydrogen concentrations in these investigations were 20 ppm,5 1 to 30 ppm,6 and 200 to 390 ppm.4 However, Wood and Daniels7 observed a rather pronounced ductility minimum at hydrogen contents ranging from 19 to 252 ppm. Those theories of hydrogen embrittlement involving the precipitation of diatomic hydrogen which have been applies to ferrous metals8-12 do not seem to be applicable to the case of columbium and other exothermic occluders. Such theories propose that extensive crack formation and propagation occurs by the precipitation and expansion of diatomic hydrogen at internal voids and microcracks. However, photomicrographs of hydrogenated columbium do not show any evidence of damage introduced by the sorption and precipitation of diatomic hydrogen; rather, at high hydrogen concentrations, a hydrogen-rich second phase is precipitated.13'14 In addition, a number of these theories require the development of high hydrogen pressures at voids in the structure.8'10'12 This does not appear to be feasible in the concentration ranges discussed in the aforementioned paragraphs. The possible interaction of atomic hydrogen with microcracks resulting from dislocation pile-ups15,16 remains in doubt since pile-ups have not been observed in bcc metals17 including columbium.18 Wood and Daniels7 have put forth the possibility that a hydride precipitation could be responsible for crack nucleation in columbium. Work by Longson19 has shown that hydrogen embrittlement of columbium parallels the bulk solubility limit; i.e., as the solubility increases, for instance with temperature, the amount of hydrogen necessary to cause embrittlement also increases. Although a hydride precipitation appears attractive as a means of nucleating microcracks in columbium, what require more intensive study are the low-temperature anomalies which have been observed, i.e., the ductile-brittle-d'ictile transition characteristics. Also, the hydrogen concentrations where embrittlement occurs are often below the bulk solubility limits determined by Albrecht et al.13,14 and Walter and Chandler.20 This work is an attempt to determine more definitively the effects of concentration and temperature on the mechanical properties of dilute Cb-H alloys. EXPERIMENTAL PROCEDURE Ultrahigh-purity columbium rods, obtained from the Wah Chang Corp., were cold-reduced by rotary swaging. A chemical analysis is given in Table I. The material was cut into cylindrical blanks 1.50 ±0.005 in. long. Individual specimens were either given a stress relief anneal at 750°C or recrystal-lized at 1200°C. Resulting microstructures were either a "bamboo" structure characteristic of a wrought material or a recrystallized structure with a grain diameter of approximately 100 n. All heat treatments were carried out in a vacuum of 10-5 Torr or less.

Jan 1, 1969

By J. L. Jorstad

The hypereutectic Al-Si alloys 390 and A390 have wear characteristics superior to any of the more common aluminum casting alloys. This excellent wear resistance, coupled with good mechanical properties, high hardness, and low coefficient of thermal expansion, has made these alloys candidates for the all-aluminum internal combustion engine, the application for which they were primarily developed. A390 alloy is intended for sand and permanent mold casting, and requires a lower iron ccxltent (0.5 pct maximum) than its die casting companion 390 alloy (0.6 to 1.1 pct Fe). The 17 pct nominal silicon in these alloys provides sufficient quantities of the hard primary silicon phase to assure a high degree of wear resistance, yet little enough of this phase, to minimize the casting and m achining problems associated in the past with the hypereutectic alloys. The mechanical and physical properties of 390 and A390 alloys are competitive with the best of the common aluminum casting alloys with the exception of low ductility. This low ductility is not considered a detriment, since in many applications these alloys replace cast iron. Corrosion resistance is similar to the standard alloys 380 and 333. Numerous parts, of varying degrees of complexity, have been cast of alloys 390 and A390, including engine blocks and heads. The deviations from normal good handling and casting practices that are required for the alloys are those associated with the presence of the primary silicon. To obtain optimum strength and machinability, the molten alloys should be treated with phosphorus to refine the primary silicon phase. Care must be exercised to properly control the pouring temperature and rate in order to minimize primary silicon growth and segregation. AUTOMOTIVE engineers have for years recognized the advantages of lighter weight and better heat transfer that aluminum could offer as material of construction for engine blocks. These advantages alone, however, are insufficient justification for acceptance of aluminum engines by the automotive industry. To be acceptable, an aluminum engine first must pass all tests to which cast-iron engines are subjected, and, in addition, must represent no cost penalty in manufacturing. None of the conventional aluminum casting alloys have sufficient wear resistance to withstand the tests to which cast iron is subjected as a cylinder bore material, and recent attempts to manufacture aluminum engines with cast-in-place iron sleeves could not compete costwise with the equivalent cast-iron engine. The prerequisite to an acceptable aluminum engine seemed to be a casting alloy with a high degree of wear resistance that would eliminate the necessity of cast-in iron sleeves or liners. The hypereutectic A1-Si alloys 390 and A390 have met this challenge.' Combined with modified pistons and a patented cylinder bore surface finish,2 the performance of these alloys in more than 1300 cold start and cold scuff tests, over 3500 hr of dynamometer wear and endurance tests, and more than 350,000 miles of road tests leaves no doubt as to the feasibility of running on bare aluminum cylinder bores. ALLOY DEVELOPMENT The desirable characteristics of the hypereutectic A1-Si alloys have been recognized for some time. Their excellent wear resistance and low coefficient of thermal expansions have been used to advantage in the production of diesel-type pistons in Europe and to a limited extent in this country. The major contributor to the good wear resistance of these alloys is the extremely hard primary silicon phase in the microstructure. Although the percent silicon used experimentally has been much higher, most commercial alloys have ranged from about 14 to 25 pct. Generally, as the silicon content is increased, wear resistance increases, and the coefficient of thermal expansion decreases. With increases in silicon, however, machinability and cast-ability tend to suffer. The development of a satisfactory aluminum engine block material at Reynolds involved the testing and evaluation of many alloys, covering a wide range of silicon contents and numerous variations of iron, copper, magnesium, manganese, and other alloying additions. Castability, mechanical and physical prop-

Jan 1, 1969

By M. O. Abo-el Fotoh, J. B. Mitchell, J. E. Dorn

The effect of strain rate and temperature on the tensile flow stress of a polycrystalline bcc alloy of magnesium containing 14 wt pct Li and 1.5 wt pct Al was investigated for strain rates of 3.13 x lom5 to 3.13 x 10-3 per sec over the range from 20° to 300°K. From about 180° to 300°K the alloy exhibited an ather-ma1 deformation behavior where the flow stress was independent of strain rate and increased only slightly with decreasing temperature. At lower temperatures the flow stress was strongly strain-rate- and temperature-dependent, characteristic of deformations controlled by thermally activated mechmzisms. The activation volume for thermally activated plastic defornzation was between 5 and 30 cu Burgers vectors, independent of plastic strain. This low-temperature thermally activated deformation behavior was found lo be in satisfactory agreement with the theoretical dictates of the Dorn-Rajnak1 formulation of the Peierls mechanism where deformation is controlled by the rate of nucleation of pairs of dislocation kinks over the Peierls energy barriers. SEVERAL studies of the low-temperature thermally activated deformation of bcc metals and alloys (molybdenum,1 tantalum,1 Fe-2 pct Mn,2 Fe-11 pct MO,3 and AgMg4) have revealed that the strain rate is controlled by the activation of dislocations over the Peierls-Nabarro energy hills. Although there is some uncertainty as to the nature and effect of solute atom-dislocation interactions during low-temperature deformation of bcc metals, it has been concluded by Dorn and Rajnak,1 Conrad,1 and Christian and Masters6 among others that overcoming the Peierls-Nabarro stress which arises from the variations in bond energies of atoms in the dislocation core as it is displaced is the probable mechanism controlling low-temperature deformation. The purpose of this research was to investigate the low-temperature plastic deformation of the bcc alloy Mg-14 wt pct Li-1.5 wt pct A1 to determine if the behavior of this alkali metal alloy might be analogous to that for other bcc metals. This alloy was selected because of its availability and its current industrial importance as a lightweight material for aircraft and aerospace applications. I) EXPERIMENTAL PROCEDURE Polycrystalline tensile specimens having cylindrical gage sections 2 in. long by 0.2 in. in diam were machined from as-received alloy sheet stock of Mg-14 wt pct Li-1.5 wt pct Al. Specimens were annealed in an argon atmosphere at 423°K for 4 hr and maintained in a kerosene bath together with the sheet stock to prevent corrosion. The resulting specimen microstructure consisted of a coarse uniform dispersion of incoherent precipitate MgLi2Al particles7 in a bcc 0 phase matrix having an average grain size of 150 p. Prior to testing the specimens were chemically polished in dilute hydrochloric acid. Comparison of tensile properties and microstructures of specimens cut from center and edge sections of the sheet stock revealed no effects of inhomogeneities in the sheet material. Tensile tests were performed on an Instron machine at crosshead speeds corresponding to tensile strain rates of 1.56 x 10-5 and 1.56 x 10"3 per sec. Stresses were determined to ±2 x 106 dynes per sq cm and strains to within ±0.0001. Average values of shear stress t and shear strain y reported were taken as one half the tensile stress and three halves the tensile strain, respectively. Flow stresses were taken at 0.05 pct strain offset. Test temperatures down to 77°K were obtained by immersing the specimens in constant-temperature baths. Lower-temperature tests were performed in a liquid helium cryostat to within ±2°K of the reported values. Prior to testing at the various temperatures and strain rates all specimens were prestrained at 2 35°K at a shear strain rate of 3.13 x 10-5 per sec to a stress level of 0.606 x 10' dynes per sq cm to obtain a uniform initial state. Additional tests were made to determine the effect of changes in strain rate and strain on the flow stress by rapidly changing the crosshead motion during testing. Shear moduli of elasticity, needed for analyses of the data, were obtained at several temperatures by a common technique of determining the resonant frequencies of vibrations of rectangular test specimens. 11) EXPERIMENTAL RESULTS Fig. 1 shows the experimentally determined flow stress vs temperature for two strain rates. Two distinct regions of behavior are evident. Below about 180°K the strong increase in flow stress with increased strain rate and decreasing temperature indicates that deformation is controlled by a thermally activated dislocation mechanism. At higher temperatures an athermal region is evident where the flow stress is independent of strain rate and only slightly dependent on temperature. The applied stress t to cause plastic flow was separated into two components:

Jan 1, 1969

By H. W. Schadler

The superplastic behavior of low carbon and manganese bearing steels has been evaluated. The results of elevated-temperature stress-strain rate and elongation tests are reported which indicate that high strain rate sensitivity (>0.5) and adequate elongations are achievable in ultrafine-grained steels 1 to 2 p, but at strain rates which are not commercially attractive. It has been demonstrated that the fine grain size is retained after long times and high strains if the temperature is kept within the range of the two-phase (a + ?) field. INTEREST in superplasticity has been stimulated by the desire to: 1) understand the origin of, and mechanisms responsible for, the large uniform elongations observed, and 2) exploit this property for commercial advantage in metal forming operations. Although the Zn-22 wt pct Al alloy presently being studied as a model material1-5 may find application in sheet forming and extrusion, the potential of super-plasticity should best be realized in large tonnage materials, such as steel and aluminum alloys. The degree of superplasticity in low-carbon and manganese-bearing steels has been evaluated. The results of elevated-temperature stress-strain rate and elongation tests on ultrafine grain size material are reported. Avery and Backofen6 and Hart7 have shown that geometrically stable flow leading to extensive uniform elongation in the tension test is associated with high values of the strain rate sensitivity, m, defined: Lozinsky had reported that titanium and zirconium experience permanent deformation if subjected to a constant load and cyclic heating through the temperature range of the phase transformation. Although strain rate sensitivities in excess of about 0.2 had not been reported previously for steel, permanent deformation had been observed11-13 in a wide variety of steels subjected to a constant load and cyclic heating through the temperature range of the a-? phase transformation. Thus by analogy, steel could be expected to exhibit high strain rate sensitivity but only in the a + ? condition. High strain rate sensitivity has been observed at 650°C (a + Fe3C), but not reported as such, by Bailey, Dickenson, and pearson14 in 1931 at a strain rate of about 10-9 per min. It then remained to determine whether high tensile elongations would be observed in a rate-controlled test at constant temperature and at what strain rate strain rate sensitivity values greater than 0.5 would be observed. Since previous experience8 had indicated the importance of fine grain size to realizing high m at reasonable strain rates, it was first necessary to produce an ultrafine grain size and then keep the grains from growing during the test. The results of this investigation show that fine grain size can be readily produced16 and maintained by restricting the temperature of testing to below the ? transus. Further, superplasticity (high m and large uniform elongation) is observed. However, the strain rate range is only marginally useful for commercial forming operations with the finest grain size produced. MATERIAL The material investigated initially was a 1.9 wt pct Mn, 0.42 wt pct C, hot-rolled bar previously used by Low and Turka1015 and available in the laboratory. The 0.500-in. round was cold-rolled to a 0.090-in. flat, annealed for 4 hr at 850°C in argon, air-cooled, and cold-finished to 0.050 in. Subsequently, four additional steels of the compositions given in Table I were investigated to explore the effects of manganese, carbon, and test temperature on the observed stress-strain rate behavior. These steels were melted under argon, cast to 0.75 by 2 by 5 in. slabs, hot-rolled at 850°C, surface-finished to 0.13 in., and cold-finished to 0.050 in. Sheet tensile specimens 0.200 in. x thickness with 1- or 2-in. gage length were cut parallel to the rolling direction. Table I also includes the nominal transformation temperatures for the AISI 1340 and the four experimental steels. EXPERIMENTAL PROCEDURE Production of Fine Grain Size. Ultrafine grain size (1 to 5 p) was considered essential for this studv. Grange16 has described two techniques for producing

Jan 1, 1969

By B. Wilshire, W. J. Evans

The high-temperature creep properties of nickel, zinc, and iron have been determined over a range of stresses. The creep strain, E, was found to vary with time, t, as: where e0 is the instantaneous strain on loading, ET the total transient creep strain, $ the steady creep rate, and m is a constant relating to the rate of exhaustion of transient creep. Deviations from this relationship occurred during the initial 10 to 15 pct of the transient stage. These deviations result in the initial creep rate, go, calculated as (m . ET + es), being considerably lower than those obtained by measurements on the creep curve. For all materials, the initial creep rate, the constant m, and the duration of transient creep are all related to the steady creep rate. These relationships suggest that transient and steady-state creep should not be regarded as distinct stages.

Jan 1, 1969

By M. S. Seltzer

In a previous paper1 it was shown that activation energies for steady-state creep in lead sulfide single crystals varied with the concentration of electronic defects. For n-type lead-excess crystals, values for the creep activation energy, Qc, decreased from 2.9 to 2.2 ev as the carrier concentration increased from 1017 to 1017 electrons per cu cm, while Q, increased from 1.6 to 2.3 ev for p-type sulfur-excess crystals as the concentration of holes increased from 6 X 1017 to 1018 per cu cm. It was also shown in Ref. 1 that the Q, values could best be correlated with the sum of the self-diffusion activation energies in PbS, i.e., for a given concentration of electrons or holes Q, = QPb + Qs, where Qpb and QS are the activation energies for diffusion of pb210 and s35 in PbS. This result suggests that creep rates are controlled by at least two atomic defects, one for lead migration and one controlling sulfur transport. It would be most desirable to interpret these creep energies in terms of an atomic defect disorder model for lead sulfide. Studies of creep rates as a function of sulfur pressure2 indicate that the defects controlling creep rates are singly ionized lead and sulfur vacancies, VPb and Vs. This hypothesis can be more firmly established by determination of Q, under conditions of constant atomic defect concentration rather than constant electronic defect concentration as has been previously done. Therefore, several measurements have been made of Q, on crystals whose con- centration of lead vacancies or sulfur vacancies has been fixed by equilibration under appropriate sulfur pressure and temperature. It was indicated in Ref. 2 that high-temperature isotherms are available which show how the concentrations of various atomic point defects in PbS vary with composition over the entire homogeneity range for the compound. Two such isotherms are shown in Fig. 1 for 900" and 1000°K. Utilizing these isotherms the concentration of a given defect, say Vbb, may be held constant over a particular temperature range by adjusting the sulfur pressure as the temperature is changed. Thus the concentration of one defect suspected of controlling creep rates may be held constant while other defect concentrations vary. The apparent activation energy for formation of these defects can be obtained from the isotherms giving their concentration as a function of sulfur pressure. Activation energies for creep obtained under conditions of constant defect concentration can then be compared with defect formation energies and certain possible atomic defects can be eliminated as creep-controlling species. We have performed creep experiments as a function of temperature at a stress of 244 g per sq mm under conditions which fixed the lead vacancy concentration, V', at 1016, 3.2 x 1016, and 3.2 x 1017 cm-3, and one were the sulfur vacancy concentration, Vs, was held at lo17 cm-3. The results are presented in Fig. 2 as creep rate, k, vs reciprocal of absolute temperature, 1/T. Specimens 34, 35, and 36 were deformed under constant lead vacancy concentration while specimen

Jan 1, 1969

By Carl F. Cline, Richard R. Vandervoort, Willis L. Barmore

THE objective of this investigation was to determine the high-temperature plastic deformation behavior of stoichiometric uranium mononitride as a function of stress and temperature. Interest in the properties of this material stems from its potential use in high-temperature nuclear reactor systems. The creep of other refractory compounds containing uranium (e.g., U02, UC) has been studied by various investigators.1"4 Fassler et al.4 have studied the creep of UN in vacuum from 1100° to 1350°C at stresses of 6000 and 8000 psi. In the present work, the creep of stoichiometric UN was investigated from 1500° to 1800°C at stresses from 2000 to 5000 psi in a partial pressure of 200 mm of nitrogen. The specimens were prepared by hot isostatic pressing of UN powder into cylinders of $ in. diam by about 1 in. high. After pressing, the specimens were heat-treated in nitrogen at 1900°C for 50 hr. The densities of individual specimens were determined by the water displacement method. All specimens were theoretically dense, based on a value of 14.32 g per cu cm.5 Principal metallic impurities in ppm by weight were: Ca, 50; Cu, 5; Fe, 30; Mg, 5; Ni, 10; and Si, 20. Oxygen content was 400 ± 50 pprn and carbon content was 100 i25 ppm. The nitrogen content was 5.56 ±0.05 wt pct. The average grain size for five specimens, as determined by the intercept method, was 0.14 i 0.01 mm. One specimen had a grain size of 2.0 mm. This large grain size is an anomaly, since all specimens had the same chemical and thermal histories. Specimens of 1/4 in. diam by 1/2 in. high were creep-tested in compression in a clam shell furnace heated by W-25 pct Re sheet elements. Temperature was measured to ilODC by an optical pyrometer which had been calibrated by a standard source. The distance between fiducial marks on the specimen was measured before placement into the furnace. The furnace chamber was evacuated to 10-5 Torr and back-filled to 200 mm N2. After heating rapidly to temperature, the load was applied and controlled to ±2 pct by an Instron testing machine. Upon initial loading, the specimen was deformed until a constant crosshead rate was obtained, then quenched to room temperature, remeasured, and replaced in the furnace. Upon subsequent reloading at temperature, the crosshead rate was constant for the selected condition indicating steady-state creep.

Jan 1, 1969

By D. Kunstelj, M. Stubicar, A. Tonejc, A. Bonefacic

A. Bonefafcic, D. Kunsfeli, M. Stubicar, and A. Tonejc The present communication is concerned with the variation of the texture in aluminum wires with die angle and temperature, at constant speed of extrusion. Experiments were carried out concurrently on refined samples, with a stated purity of 99.997 pct pure A1 and commercial samples of 99.5 pct Al. Ingots of refined aluminum samples were machined to 30-mm-diam by 150-mm-long billets. These billets were transformed to 5-mm-diam wires by drawing. The final form, suitable for examination, was obtained by extrusion through conical-face dies with a 1-mm hole diam and extrusion ratio 5:l in diam. The initial form of the commercial aluminum samples was drawn wire 5 mm in diam. These samples showed a poorly defined texture with (111) as a major and (001) as a minor component. A similar defined texture appeared in the refined aluminum samples after drawing to 5 mm diam. Conical-face dies with different angles (defined by the axis and the generating line of the cone) were used in our experiments. The values of the angles were 27, 35, 45, 57, 63, and 90 deg. The extrusion container was fitted with a heating element and controller permitting temperatures up to 600°C to be maintained within i5"C. Extrusion was performed at 250°, 300°, 350°, 400°, and 500°C at constant speed (approximately 1 mm per sec) and constant die reduction. The extrusion product was a wire 1 mm in diam and approximately 20 cm long. In order to remove the surface layer with the "conical" texture and to reduce the absorption by the X-ray examination of the samples, the extruded wire was etched to 0.22 mm in diam. Experiments were performed in the middle sections of the 20-cm-long wires. In addition to the die of l-mm hole diam, dies with a 1.5-, 0.7-, 0.6-, 0.5-, and 0.4-mm hole diam and 63-deg die angle were constructed. In our experiments we did not find in these ranges any important difference concerning the texture of the extruded wires and we continued our work solely on the 1.0-mm die. The diffracted X-rays (Cu K radiation) were recorded photographically. Diffracted intensities were measured on the (111) reflection with a microphotometer. The relative amounts of texture components were determined from the areas under the diffracted maxima. We found the texture of extruded aluminum wires to be strongly influenced not only by the temperature of extrusion and the purity of the sample but also by the form of the die. It is generally admitted that cold-drawn aluminum wires have mainly a (111) texture with a small amount of (001) component, Table I of Ref. 1. In our experiments with wires extruded in conditions represented by Fig. 1, in some cases a single (001) texture was obtained. If these wires were drawn repeatedly at room temperature, X-ray measurements revealed a duplex (001)-(111) fiber texture. Further drawings increased the (111) and decreased the (001) texture component. In Fig. 1 the percentage of material oriented with (001) parallel to the extrusion direction is represented as a function of the temperature and the die angle (a), for commercial and refined aluminum samples, respectively. From these diagrams we may draw the following conclusions. The slope of the die (a) influenced more strongly the texture at the lower rather than the higher temperatures. Again, a stronger influence was found in the case of the commercial in comparison with refined aluminum samples. In the case of the commercial aluminum samples the amount of material with (001) texture increases with increasing wire temperature in an approximately linear manner. This effect is less pronounced in the pure aluminum samples, with the exception of the die with a = 45 deg. In this case the (001) texture decreases with increasing temperature, as shown in Fig. 1. Component (001) is more pronounced in higher-purity aluminum samples. Our experiments led to the conclusion that both (001) and (111) components are essentially stable in extruded aluminum wires. As we obtained a single (001) texture starting with a sample of drawn wire in which the (001) component was very weak, our experiments revealed that the (001) component is not a remnant of the initial texture; this is in disagreement with the findings of Vandermeer and McHargue.1 We gratefully acknowledge discussions with Professor M. Paic. 1 R. A. Vandermeer and C. J. McHargue: Trans. 7MS-AME, 1964, vol. 230, p. 667.

Jan 1, 1969

By D. F. DeSante, A. S. Tetelman

MICROCRACKS are often introduced into commercial metals during fabrication processes such as swaging, cold rolling, deep drawing, and welding. These microcracks act as strain concentrators and may be capable of causing premature catastrophic failure of a component or weld. The present investigation was undertaken to determine whether high-temperature annealing treatments may be capable of reducing or negating the detrimental effects of such existing microcracks. Internal microcracks, ranging from 0.1 to 0.85 mm in length and averaging 0.23 mm, were introduced into polycrystalline Fe-3 pct Si tensile specimens (0.155 mm grain size) by the cathodic charging of hydrogen.1'2 The typical appearance of such microcracks and their associated strain patterns (made visible by the technique of dislocation etch pitting3) is shown in Fig. 1. The stress fields of the dislocation loops formed during plastic relaxation stabilize the microcracks so that, when the internal hydrogen pressure is removed: the microcracks stay open, rather than disappear as perfectly elastic cracks would be expected to do.' As shown in Fig. 2, such stopped microcracks cause a 36 pct decrease in the macroscopic cleavage fracture strength at -196°C.

Jan 1, 1969

By J. Campbell

Long freezing range casting alloys are particularly susceptible to a type of porosity which is observed to form in layers parallel to the supposed position of the isotherms in the solidifying casting. Under favorable conditions (which appear to be typified by low-temperature gradients in the casting giving rise to a wide and more or less uniform pasty zone, and which arise from several factors, particularly: a) wide freezing range alloy, b) high thermal conductivity of metal, c) low thermal conductivity of mold, and d) high mold temperature3) layer porosity has been observed in many different casting alloys: copper,' aluminum, magnesium,' steels, and high-temperature alloys.3 Baker4,5 and later cibula6 argue that layer porosity occurs because of thermal contraction, in a manner analogous to hot tearing. In outline, the theory consists of the establishment of a coherent dendrite network by the impinging of dendrite tips. Subsequent shrinkage imposes tensile stresses on the network which tears perpendicularly to the stress, i.e., parallel to the isotherms. If these tears are not filled by the inflow of residual liquid then layers of porosity result. Baker7 attempted to test whether the porosity was the result of thermal contraction by casting test pieces in a mold designed to accentuate hot tearing. However, no significant increase in porosity was observed. This negative result of Baker's critical experiment appears to be substantiated by numerous observations, particularly the experiments by Lagowski and Meier8 on Mg-Zn alloys covering the range of zinc contents up to 30 pct Zn. These clearly reveal that the maxima for the incidence of hot tearing and layer porosity are well-separated, occurring at 1 and 6 pct Zn, respectively. Furthermore, the thermal contraction maximum occurred at 1 pct Zn, indicating that hot tearing is associated with contraction in the solid state, and not with porosity. These observations are further substantiated by the elementary consideration that the thermal contraction of the casting is likely to produce (if anything, since the temperature difference across casting of high thermal conductivity, such as aluminum and copper, is likely to be negligible) a compressive stress on the

Jan 1, 1969

By N. Standish

By contrast with viscometry and sedimentation, no actual measurements of the applicability of Stokes' law to steelmaking have ever been reported; instead, the proof for and against Stokes' law has been inferred from the frequently observed phenomenon that inclusions collect in the top scum and the bottom of ingots. As such proof is unsatisfactory, continued reference to Stokes' law in steelmaking, even as a model for calculating the terminal velocities of rising inclusions, should be avoided. In fact, all conclusions that have been reached regarding size, density, and viscosity on the flotation of inclusions could be made more rationally without Stokes' law. A worthwhile exception is that of Mitsche1 who in 1934 used Stokes' law to show not only the expected effects of size, density, and viscosity on flotation but also the beneficial effects of i) melting under a slag layer (now Electro Slag Refining); ii) treating melts with synthetic slags (Ref. 2 gives recent applications); iii) bubbling an inert gas through the melt (recent applications in Refs. 3 and 4); and iv) altering the solid/ liquid interface characteristics. At this point, it should again be emphasized that the boundary conditions for which Stokes' law was derived place enormous restrictions on the law but its application, as noted earlier, can yield useful results in some fields under certain conditions and within well-defined limits. When compared with inclusions, which may be solid or liquid, spherical or irregular, dispersed or coagulated, interacting between themselves and the melt, floating in a liquid which is in a state of motion of varying intensity5 and contained in vessels of various shapes and sizes that may change with time as in a solidifying ingot, the conclusion is obvious-Stokes'

Jan 1, 1969

By R. W. Smith, G. W. Delamore, J. A. Spittle

RECENT work by the authors1 has demonstrated that the crystals constituting the equiaxed zone in small ingots originate, on quenching, in the chilled liquid. Whether any partial remelting2 takes place of the den-drites nucleated in the chilled region was not examined. However, the claim3 that this normally occurs, leading to crystal multiplication, has been disputed.4 Thus, for an equiaxed zone to form in the central region of an otherwise columnar ingot, it is necessary to transport crystallites from the chill zone to this region. In view of the work of Uhlmann et al.,5 it was considered desirable to examine the transport process further. Experimental Technique and Results. In the earlier experiments by the authors.1 a stainless-steel crucible 17/8 in. diam, 41/2 in. high, ad containing an alloy of A1-4 wt pct Cu, was quenched from 660°C into a bath of Wood's metal maintained at 100°C. Under these conditions a central zone of equiaxed crystals was obtained. However, if a 2250-G unidirectional magnetic field was applied for 2 sec immediately following the instant of quenching, or subsequently, the equiaxed zone did not appear. Careful thermal analysis showed that the short application of the field had virtually no effect on the thermal conditions of the melt. It thus appeared that the crystallites which were ultimately to grow large enough to form the equiaxed zone existed in the liquid immediately ahead of the interface, occlusion being prevented by the convective fluid flow induced by freezing from the walls of the cylinder. When this relative movement was prevented by the Lorenz forces induced by the application of the magnetic field, the crystallites were caught up in the rapidly advancing dendrite solid-liquid interface. To test this assumption, a small ingot of super-purity aluminum was partially melted and poured into a heated stainless-steel mold which was then immediately quenched into molten Wood's alloy. The resulting structure is shown in Fig. 1, and consists of columnar grains with a central fine-grained zone. Thus the unmelted solid present at the beginning of solidification had been transported ahead of the columnar interface. Discussion. There appears to be little or no information available on the interaction of suspended particles with a metallic solid/liquid interface. However, some information is available for transparent organic sys-

Jan 1, 1969

By J. C. M. Li

A dislocation model is constructed for a cylindrical tilt boundary of which the axis of tilt is parallel to the axis of the cylinder. The strain energy per unit area calculated from this model agrees with thut of an infinite vertical wall of edge dislocations. Based on this model, a dislocation mechanism for the shrinking of such a cylindrical boundary is proposed. The power relation between the grain boundary velocity and the driving force is accounted fm by the stress dependence of dislocation velocity. The activation area for grain boundary motion is found to correlate with that .for Creep in aluminum. In the preceding paper' the velocity of a curved grain boundary is found to be a power function of the driving force, [1] where M is the velocity at unit driving force, y is the grain boundary energy, and p is the radius of curvature. This finding adds another nonlinear rate equation to metallurgical phenomena. While a macroscopic theory for the steady state as just presented2 can be used to understand the shape of the moving boundary, such theory usually does not provide any information about the atomistics of the process. It is attempted in this paper to discuss the nonlinear rate equation in terms of a dislocation mechanism. A DISLOCATION MODEL FOR A CYLINDRICAL TILT BOUNDARY Before a dislocation mechanism can be proposed for the motion of a cylindrical tilt boundary, it is necessary to construct a dislocation model for the boundary. For simplicity, a tilt boundary in a simple cubic lattice will be examined. Although this does not represent the situation in aluminum, it is expected that the general features will be similar. The details of the model in the fcc lattice can be constructed when a refinement of the simple model is called for. A cylindrical low angle tilt boundary in a simple cubic lattice is shown in Fig. 1. Two sets of edge dislocations are needed as shown. A schematic representation is shown in Fig. 2(a). In terms of a continuous distribution of dislocations, the density of dislocations n, of Burgers vector b, in the small segment ds of the grain boundary is Similarly the density of dislocations n, of Burgers vector bz in the same segment ds is where is the tilt angle of the grain boundary. Based on this continuous distribution of dislocations in the grain boundary, it can be shown that the interaction between a small segment of the boundary and the rest of it is zero. Furthermore, the stress produced at any point inside or outside the cylinder is also zero. This shows that the model is acceptable in the sense that the boundary has no long-range stresses. Since the model of continuous distribution of dislocations in the grain boundary does not reveal the interactions among individual dislocations, a discrete dislocation model has to be used for such purpose. For simplicity, an equivalent model is shown in Fig. 3. This arises because the total Burgers vector is, from

Jan 1, 1970

By A. W. D. Hills

This paper describes the development of a generalized integral-Wofile method for the analysis of heat transfer dwing solidification. The method is extremely flexible, and can be applied to a wide range of situations. This flexibility has been achieved by characterizing the solid metal layer in terms of two parameters, and by developing two simultaneous nonlinear differential equations for these parameters in terms of the heat fluxes crossing the boundaries of the solid layer. The use of these equations is illustrated in a series of examples which involve the solidification of pure metals at zero superheat cooling under different conditions. The simplicity with which the method can be extended to treat more complicated jwoblems is illustrated in a further example which involves natwal convection effects in the liquid metal. ThE rate at which molten metal solidifies in an industrial casting process, and the structure of the cast product, are both controlled by the rate at which heat can be removed from the casting. A knowledge of heat transfer rates is thus essential to the control of the process and to the control of the structure and soundness of the final casting. Heat transfer rates during real solidification processes cannot be predicted by formal mathematical techniques, however, because nonlinear boundary conditions are involved. Approximate methods are normally used, and these have included electrical and hydraulic analogue techniques, finite difference methods, and the integral-profile method. Considerable effort has been devoted to the development of the first two techniques, but the integral-profile method has been used very little so far. This is unfortunate because the method is capable of providing relatively accurate solutions for the heat transfer equation during solidification without involving large amounts of computer time. A further advantage of the method is its flexibility, although this is not apparent from the integral-profile solutions that have been developed to date. These solutions have been derived for the solidification of molten metal at zero super-heat under cooling conditions involving either a constant heat flux from the cooled surface;' a constant heat transfer coefficient at the surface,'-3 or a specified variation in the surface temperature.4,5 A generalized integral-profile method is presented in this paper which can be used to predict unidirectional solidification rates under a very wide range of more realistic cooling conditions. The use of the method is illustrated in a series of problems involving pure metals, or skin forming alloys, solidifying at zero super-heat. However, the principal advantage that this method has over the previous integral-profile methods is the ease with which it can be extended to treat more complicated solidification problems. This is illustrated by considering a problem in which super-heat is liberated from the liquid metal by natural convection during the solidification process. In the final section of the paper the generalized method is compared with previous methods used to predict solidification rates and its extension to more complicated solidification problems is briefly discussed.

Jan 1, 1970

By A. K. Mukherjee, J. E. Dorn

A modified Peierls model is Presented for the rationalization of the asymmetric plastic behavior of single crystals of bcc metals. The model assumes that the asymmetry of slip arises from a tendency toward asymnetric splitting of the a/2[111] screw dislocation. The approach differs from former theories however insofar as it assumes that the splitting is so minor ttut only the core energy is modified and that no real partial dislocations exist. As a consequence, the concepts of a line energy of a partial dislocation, interaction between partial dislocations, constriction energies, and stacking fault energies are not invoked. Instead the present analysis is based on a specialization of the Peierls mechanism which assumes an asymmetric dislocation core which is modified by the effective stress and permits cross slip. The theoretical predictions on the stress-temperature -strain rate and orientation relationship agree qualitatively with the limited experimental data that are currently available. Additional experimental work over wider ranges of conditions is suggested to provide more complete evaluation of the possible validity of this theory. RECENT experimental investigations on the low-temperature thermally activated deformation of bcc metals have confirmed the existence of several unique orientation effects. These will be described with the aid of the standard stereographic projection shown in Fig. 1. If slip were determined exclusively by crystal symmetry, the deformation characteristics would be symmetrical about X; = 0 and independent of whether the specimen were subjected to a tension or a compression stress, regardless of what combinations of slip planes might be operative. Experiments, however, reveal that neither of these symmetry based predictions are valid. A schematic representation of the commonly observed asymmetry of both the yield stress and the plane of slip is shown in Fig. 2. A reversal of the direction of stressing results in an inversion of the asvmmetric behavior. 1) Asymmetry bf Yielding. A detailed investigation on the asymmetric yielding in an Fe-2.7 pct Si alloy was repoEted by Tabka, Tikeuchi, and Furubayashi,1 Similar trends have been observed by Keh and Nakada on iron,' Stein on molybdenum,3 Bowen, Christian, and Taylor4 on columbium, Sherwood, Guiu, Kim, and pratt5 on Ta, Cb, and Mo. The degree of asymmetry not only depends on the atomic number and alloying but, in all cases that have been examined, it also increases with a decrease in the test temperature. 2) Asymmetry of the Slip Plane. Asymmetric $I-~: curves of the type shown in Fig. 2 have been found for several Fe-Si alloys6-8,1 and columbium.4 There is general agre_ement that near X: = 30 deg slip occurs by the [111](211) mode so that ?1 = 30 deg. As X; decreases it appears that [111](211) to [111](101) cross slip takes place leading to slip band traces on intermediate planes. And as xi approaches 0 deg, sharp

Jan 1, 1970

By J. W. Spretnak, V. Kandarpa

Stress -induced ordering of carbon atoms is studied in a series of Fe-Mn-C alloys. A prominent peak is found in the vicinity of 280°C at frequencies of the order of 1.0 cps, with an associated activation energy of 37 kcal per mole. The height of the peak is linearly rekzted to the concentration of carbon in solution. The distortion of octahedral holes by manganese atoms appears to be predominant over carbon-carbon pair interactions. RELAXATION by stress-induced ordering of point defects is expected whenever the introduction of these point defects produces distortions which have a lower symmetry than that of the lattice. Under zero stress, the isolated point defects occupy the crystallographic-ally equivalent positions in the lattice, as these represent states of equal energy. However, if the defect sites are asymmetric, application of an uniaxial stress will split the energy states, and a redistribution of the defects among various states will take place. This is the case of the internal friction peak called the Snoek peak,1 resulting from isolated interstitials in bcc metals. The interstitial sites in this case have tetragonal symmetry. In the case of fcc and hcp lattices, such an effect is not expected from isolated point defects because of the symmetrical nature of the interstitial sites. However, internal friction peaks arising from interstitial diffusion have been reported both in hcp2,3 and fcc4-8 lattices. These peaks are often explained on the basis of stress-induced ordering of interstitial solutes, caused by the deviation of interstitial sites from their cubic symmetry through the presence of nearby defects. In the case of fcc lattices, evidence for interactions of both the substitutional-interstitial4,6,13 and interstitial-interstitial types5'798'14 have been presented by various investigators. The purpose of the present investigation was to study the internal friction peak attributed to the diffusion of interstitial carbon atoms in high purity austenitic manganese steels and to account for the peak in the light of the existing models. MATERIALS The Fe-Mn-C alloys used in the present investigation were made in two different ways, designated as Type I and Type 11. Type I alloys were made from high purity Fe-Mn alloys obtained in the form of 0.04- in.-diam wires from Materials Research Corporation, Orangeburg, N.Y. These alloys were carburized to different levels using gas mixtures of H2 and CH4 at 1000°C. Type I1 alloys were made in this laboratory starting with zone refined iron, spectrographically pure manganese, and spectrographically pure carbon. They were melted in an argon arc melting furnace and drawn into 0.04-in.-diam wires. All the wires were annealed at about 900°C for 3 hr prior to the internal friction experiments. After the measurements of internal friction, the phases in the samples were identified by X-ray diffraction and the carbon determined by the combustion method. EXPERIMENTAL PROCEDURE In the present work, a classical Ke-type pendulum was used. The details of the equipment were described previously by D. T. Peters.9 Dry helium at 40 torr was used in all the experiments. The internal friction, measured as the logarithmic decrement of the torsion amplitude of vibration was determined as a function of temperature, from ambient to about 500°C. The background internal friction was assumed to have the form of the exponential of the inverse temperature and was subtracted from the raw data. The height of the peak was measured at the position of the maximum in the plot of the internal friction versus temperature. The activation energies of the peaks were measured by the peak shift method. The internal friction values for an alloy were obtained as a function of temperature at different frequencies of vibration. The position of the peak changes with frequency, the higher the frequency the higher the peak temperature. The activation energy of the process associated with the peak is obtained using the formula

Jan 1, 1970